CNC4PC C34SDF Connector Board for F Series User manual

Brand
CNC4PC
Model
C34SDF Connector Board for F Series
Type
User manual
USER’S
MANUAL
VER. 1
C34SDF-BOARD
Rev. 1
DECEMBER 2021
User’s Manual Page i
USER'S MANUAL
TABLE OF CONTENTS
Contents Page #
1.0 OVERVIEW ..................................................................................................................... 1
2.0 FEATURES ..................................................................................................................... 1
3.0 BOARD DESCRIPTION .................................................................................................. 2
4.0 JUMPER TO SELECT THE ENABLE ............................................................................. 2
5.0 WIRING SAMPLE ........................................................................................................... 5
5.1 Diagram of connection with input signals Step & Dir and C76. ............................. 5
5.2 Diagram of connection with input signals Differentials C74 and C76. ................... 5
6.0 PINOUT ........................................................................................................................... 6
7.0 DIMENSION .................................................................................................................... 7
User’s Manual Page 1
1.0 OVERVIEW
This board interface is used for the connection between C82, C76, M16D, C62 and the F
AC SERVO DRIVER
2.0 FEATURES
• DB25 FEMALE connector for Driver Connection.
• RJ45 Connector for Axis.
• Encoder Output.
• Alarm terminal
• Select Jumper for Hard Enable or Soft Enable.
• Select jumper for signal differentials.
• Select Jumper active Low and active High
• Terminals for external drive enable push button.
User’s Manual Page 2
3.0 BOARD DESCRIPTION
4.0 JUMPER TO SELECT THE ENABLE
Use Software Enable to keep the driver active only while the system is active.
Set of jumpers as shown in the image.
SOFT ENABLE
Use Hardware Enable to keep the driver enabled all the time.
Set of jumpers as shown in the image.
User’s Manual Page 3
HARD ENABLE
JUMPER TO SELECT THE DIFFERENTIAL
If working the inputs of STEP and DIR as differentials signals, you have to use the board, set
jumper as shown in the image.
DIFERENTIAL.
If not use the differential signal for STEP & DIR, set jumper as show in the image.
STEP & DIR
User’s Manual Page 4
JUMPER TO SELECT ACTIVE LOW AND ACTIVE HIGH
1-2: ACTIVE LOW
2-3: ACTIVE HIGH
User’s Manual Page 5
5.0 WIRING SAMPLE
5.1 Diagram of connection with input signals Step & Dir and C76.
5.2 Diagram of connection with input signals Differentials C74 and C76.
User’s Manual Page 6
6.0 PINOUT
Note:
* Servo ON and Alarm signals are related to the RJ45 pin 5 of the C34SDF board, but
they are not connected directly to this pin.
RJ45 for Encoder
F SERIES SERVO DRIVE AND C34SDF
CONNECTION
DB25 FEMALE
PIN
FUNCTION
RJ45 PIN
21
SERVO ON *
5
8
COM+
7
-
+ 5V
8
3,16
COM- / GND
4
15
ALARM *
5
7
DIR-
3
19
DIR+
6
6
STEP-
1
18
STEP+
2
DB25
FEMALE PIN
RJ45 PIN
FUNCTION
3, 16
1
GND
-
2
5VDC
13
3
Z-
25
4
Z+
11
5
A-
23
6
A+
12
7
B-
24
8
B+
User’s Manual Page 7
7.0 DIMENSION
All dimensions are in Millimeters.
DISCLAIMER
Use caution. CNC machines can be dangerous machines. Neither DUNCAN USA, LLC
nor Arturo Duncan are liable for any accidents resulting from the improper use of these
devices. This product is not a fail-safe device and it should not be used in life support
systems or in other devices where its failure or possible erratic operation could cause
property damage, bodily injury or loss of life.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9

CNC4PC C34SDF Connector Board for F Series User manual

Brand
CNC4PC
Model
C34SDF Connector Board for F Series
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents