Rohde&Schwarz FPL1000 User manual

COMPANY RESTRICTED

R&S®FPL1000

Spectrum Analyzer

User Manual

1178337002

Version 14

(;ÜQÔ2)

This manual applies to the following R&S®FPL1000 models with firmware version 2.10 and later:

●R&S®FPL1003 (1304.0004K03) - FPL1000 with maximum frequency 3 GHz

●R&S®FPL1007 (1304.0004K07) - FPL1000 with maximum frequency 7.5 GHz

●R&S®FPL1014 (1304.0004K14) - FPL1000 with maximum frequency 14 GHz

●R&S®FPL1026 (1304.0004K26) - FPL1000 with maximum frequency 26.5 GHz

In addition to the base unit, the following options are described:

●R&S FPL1-B4, OCXO (1323.1902.02)

●R&S FPL1-B5, Additional Interfaces (1323.1883.02)

●R&S FPL1-B9, Internal Generator (1323.1925.03/1323.1925.07)

●R&S FPL1-B10, GPIB interface (1323.1890.02)

●R&S FPL1-B11, YIG preselector bypass (1323.1619.02)

●R&S FPL1-B22, preamplifier (1323.1719.02)

●R&S FPL1-B25, electronic attenuator (1323.1990.02)

●R&S FPL1-B30, DC power supply (1323.1877.02)

●R&S FPL1-B31, Li-Ion battery pack and charger (1323.1725.02)

●R&S FPL1-K9, Power sensor support (1323.1754.02)

●R&S FPL1-K54, EMI measurements (1323.1783.02)

Muehldorfstr. 15, 81671 Muenchen, Germany

Phone: +49 89 41 29 - 0

Email: [email protected]

Internet: www.rohde-schwarz.com

Subject to change – data without tolerance limits is not binding.

R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KG.

All other trademarks are the properties of their respective owners.

1178.3370.02 | Version 14 | R&S®FPL1000 | COMPANY RESTRICTED

Throughout this manual, products from Rohde & Schwarz are indicated without the ® symbol , e.g. R&S®FPL1000 is indicated as

R&S FPL1000, R&S® FPL1-Bxx/-Kxx is indicated as R&S FPL1-Bxx/-Kxx.

Contents

R&S®FPL1000

3User Manual 1178.3370.02 ─ 14

Contents

1 Safety and regulatory information......................................................13

1.1 Safety instructions......................................................................................................13

1.2 Labels on R&S FPL1000............................................................................................. 16

1.3 Warning messages in the documentation................................................................ 17

1.4 Korea certification class A......................................................................................... 17

2 Documentation overview.....................................................................18

2.1 Getting started manual............................................................................................... 18

2.2 User manuals and help...............................................................................................18

2.3 Service manual............................................................................................................18

2.4 Instrument security procedures................................................................................ 19

2.5 Printed safety instructions.........................................................................................19

2.6 Data sheets and brochures........................................................................................ 19

2.7 Release notes and open source acknowledgment (OSA).......................................19

2.8 Application notes, application cards, white papers, etc......................................... 19

2.9 Video tutorials............................................................................................................. 20

2.10 Calibration certificate................................................................................................. 20

3 Welcome to the R&S FPL1000............................................................ 21

3.1 Key features.................................................................................................................21

4 Getting started......................................................................................22

4.1 Preparing for use........................................................................................................ 22

4.1.1 Lifting and carrying........................................................................................................22

4.1.2 Unpacking and checking............................................................................................... 22

4.1.3 Choosing the operating site.......................................................................................... 23

4.1.4 Setting up the R&S FPL1000........................................................................................ 23

4.1.5 Connecting to power..................................................................................................... 25

4.1.6 Switching on or off.........................................................................................................28

4.1.7 Connecting to LAN........................................................................................................ 29

4.1.8 Connecting a keyboard................................................................................................. 30

4.1.9 Connecting an external monitor.................................................................................... 30

4.1.10 Windows operating system........................................................................................... 32

COMPANY RESTRICTED

Contents

R&S®FPL1000

4User Manual 1178.3370.02 ─ 14

4.1.11 Logging on.................................................................................................................... 33

4.1.12 Checking the supplied options...................................................................................... 35

4.1.13 Performing a self-alignment.......................................................................................... 35

4.1.14 Considerations for test setup........................................................................................ 36

4.2 Instrument tour............................................................................................................36

4.2.1 Front panel view............................................................................................................36

4.2.2 Rear panel view............................................................................................................ 43

4.3 Trying out the instrument...........................................................................................48

4.3.1 Measuring a basic signal...............................................................................................49

4.3.2 Displaying a spectrogram..............................................................................................50

4.3.3 Activating additional measurement channels................................................................52

4.3.4 Performing sequential measurements.......................................................................... 56

4.3.5 Setting and moving a marker........................................................................................ 57

4.3.6 Displaying a marker peak list........................................................................................ 59

4.3.7 Zooming into the display............................................................................................... 60

4.3.8 Saving settings..............................................................................................................63

4.3.9 Printing and saving results............................................................................................ 65

4.4 Operating the instrument........................................................................................... 66

4.4.1 Understanding the display information - spectrum mode..............................................66

4.4.2 Accessing the functionality............................................................................................74

4.4.3 Entering data.................................................................................................................79

4.4.4 Touchscreen gestures...................................................................................................80

4.4.5 Getting help...................................................................................................................83

5 Applications, measurement channels, and result displays............. 85

5.1 Available applications.................................................................................................85

5.2 R&S MultiView............................................................................................................. 87

5.3 Defining channel setups.............................................................................................87

5.4 Running a sequence of measurements.................................................................... 89

5.4.1 The sequencer concept.................................................................................................89

5.4.2 Sequencer settings....................................................................................................... 92

5.4.3 How to set up the sequencer........................................................................................ 92

5.5 Channel setup overview............................................................................................. 93

5.6 Configuring result displays........................................................................................94

COMPANY RESTRICTED

Contents

R&S®FPL1000

5User Manual 1178.3370.02 ─ 14

5.6.1 Laying out the result display with the smartgrid............................................................ 94

5.6.2 Changing the size of windows.......................................................................................99

6 The spectrum application (RF measurements)............................... 100

6.1 Configuration overview............................................................................................ 100

6.2 Measurements and results.......................................................................................102

6.2.1 Basic measurements...................................................................................................103

6.2.2 Basic evaluation methods........................................................................................... 123

6.2.3 Power sweep measurements......................................................................................126

6.2.4 Channel power and adjacent-channel power (ACLR) measurement..........................133

6.2.5 Carrier-to-noise measurements.................................................................................. 155

6.2.6 Occupied bandwidth measurement (OBW).................................................................158

6.2.7 Spectrum emission mask (SEM) measurement..........................................................164

6.2.8 Spurious emissions measurement.............................................................................. 204

6.2.9 Statistical measurements (APD, CCDF)..................................................................... 217

6.2.10 Time domain power measurement..............................................................................231

6.2.11 Harmonic distortion measurement.............................................................................. 237

6.2.12 Third order intercept (TOI) measurement....................................................................243

6.2.13 AM modulation depth measurement........................................................................... 253

6.2.14 Electromagnetic interference (EMI) measurement......................................................256

6.3 Receiving data input and providing data output....................................................280

6.3.1 Radio frequency input................................................................................................. 280

6.3.2 Power sensors............................................................................................................ 282

6.3.3 Internal (tracking) generator........................................................................................289

6.3.4 Output settings............................................................................................................ 305

6.4 Frequency and span configuration......................................................................... 307

6.4.1 Impact of the frequency and span settings................................................................. 307

6.4.2 Frequency and span settings...................................................................................... 309

6.4.3 Keeping the center frequency stable - signal tracking................................................ 313

6.4.4 How to define the frequency range............................................................................. 314

6.4.5 How to move the center frequency through the frequency range............................... 314

6.5 Amplitude and vertical axis configuration..............................................................315

6.5.1 Impact of the vertical axis settings.............................................................................. 315

6.5.2 Amplitude settings.......................................................................................................317

COMPANY RESTRICTED

Contents

R&S®FPL1000

6User Manual 1178.3370.02 ─ 14

6.5.3 Scaling the y-axis........................................................................................................ 322

6.5.4 How to optimize the amplitude display........................................................................323

6.6 Bandwidth, filter and sweep configuration.............................................................324

6.6.1 Impact of the bandwidth, filter and sweep settings..................................................... 324

6.6.2 Bandwidth, filter and sweep settings...........................................................................329

6.6.3 Reference: list of available RRC and channel filters................................................... 338

6.7 Trigger and gate configuration................................................................................ 339

6.7.1 Triggering.................................................................................................................... 340

6.7.2 Gating..........................................................................................................................348

6.8 Adjusting settings automatically.............................................................................353

6.9 Marker usage............................................................................................................. 356

6.9.1 Basics on markers.......................................................................................................356

6.9.2 Marker settings............................................................................................................359

6.9.3 Marker search settings and positioning functions....................................................... 365

6.9.4 Marker (measurement) functions................................................................................ 373

6.9.5 How to work with markers........................................................................................... 394

6.9.6 Measurement example: measuring harmonics using marker functions...................... 395

6.10 Trace configuration...................................................................................................397

6.10.1 Standard traces...........................................................................................................397

6.10.2 Spectrograms..............................................................................................................416

6.10.3 Trace math.................................................................................................................. 434

6.11 Display and limit lines.............................................................................................. 436

6.11.1 Display lines................................................................................................................ 436

6.11.2 Limit lines.................................................................................................................... 438

6.12 Zoomed displays.......................................................................................................455

6.12.1 Single zoom versus multiple zoom..............................................................................456

6.12.2 Zoom functions............................................................................................................457

6.12.3 How to zoom into a diagram....................................................................................... 459

6.13 Importing and exporting measurement results for evaluation............................. 462

6.13.1 Displaying a reference trace - importing trace data.................................................... 462

6.13.2 Trace/data ex/import................................................................................................... 464

6.13.3 How to import traces................................................................................................... 468

6.13.4 How to export trace data and numerical results..........................................................468

COMPANY RESTRICTED

Contents

R&S®FPL1000

7User Manual 1178.3370.02 ─ 14

6.13.5 How to export a peak list.............................................................................................469

6.13.6 Reference: ASCII file export format............................................................................ 469

6.14 Independent CW source settings............................................................................ 473

7 Data management.............................................................................. 475

7.1 Restoring the default instrument configuration (preset).......................................475

7.2 Storing and recalling instrument settings and measurement data......................476

7.2.1 Quick save/quick recall............................................................................................... 477

7.2.2 Configurable storage and recall.................................................................................. 479

7.2.3 How to save and load instrument settings.................................................................. 484

7.3 Import/export functions............................................................................................486

7.4 Creating screenshots of current measurement results and settings.................. 489

7.4.1 Print and screenshot settings......................................................................................489

7.4.2 How to store or print screenshots of the display......................................................... 500

7.4.3 Example for storing multiple measurement results to a PDF file................................ 503

7.5 Working with test reports.........................................................................................504

7.5.1 Designing a test report template................................................................................. 505

7.5.2 Managing templates....................................................................................................514

7.5.3 Creating datasets........................................................................................................ 515

7.5.4 Creating a test report.................................................................................................. 516

7.5.5 How to create a test report..........................................................................................518

8 General instrument setup..................................................................521

8.1 Reference frequency.................................................................................................521

8.2 Display settings.........................................................................................................522

8.2.1 Display settings........................................................................................................... 522

8.2.2 How to work with the soft front panels........................................................................ 530

8.3 Language settings.................................................................................................... 531

8.4 System configuration settings.................................................................................532

8.4.1 Hardware information..................................................................................................532

8.4.2 Information on versions and options........................................................................... 532

8.4.3 System messages.......................................................................................................534

8.4.4 Firmware updates....................................................................................................... 535

8.4.5 General configuration settings.................................................................................... 536

8.4.6 Additional interfaces....................................................................................................537

COMPANY RESTRICTED

Contents

R&S®FPL1000

8User Manual 1178.3370.02 ─ 14

8.5 Service functions...................................................................................................... 537

8.5.1 R&S support information............................................................................................. 538

8.5.2 Self-test settings and results....................................................................................... 539

8.5.3 Calibration signal display............................................................................................ 539

8.5.4 Service functions.........................................................................................................541

8.6 Toolbar configuration............................................................................................... 542

8.7 Transducers...............................................................................................................544

8.7.1 Basics on transducer factors.......................................................................................544

8.7.2 Transducer settings.....................................................................................................545

8.7.3 Reference: transducer factor file format......................................................................551

8.7.4 How to configure the transducer................................................................................. 551

8.8 Alignment...................................................................................................................554

8.8.1 Basics on alignment.................................................................................................... 554

8.8.2 Alignment settings.......................................................................................................556

8.8.3 How to perform a self-test........................................................................................... 558

8.8.4 How to align the instrument.........................................................................................558

8.8.5 How to align the touchscreen......................................................................................559

9 Network operation and remote control............................................ 560

9.1 Remote control interfaces and protocols............................................................... 560

9.1.1 LAN interface.............................................................................................................. 561

9.2 Status reporting system........................................................................................... 564

9.2.1 Hierarchy of status registers....................................................................................... 564

9.2.2 Contents of the status registers.................................................................................. 565

9.2.3 Reset values of the status reporting system............................................................... 576

9.3 The IECWIN tool........................................................................................................ 576

9.4 Network and remote control settings......................................................................578

9.4.1 General network settings............................................................................................ 578

9.4.2 Remote settings.......................................................................................................... 580

9.4.3 Compatibility settings.................................................................................................. 583

9.4.4 LAN settings................................................................................................................585

9.4.5 Remote errors............................................................................................................. 587

9.4.6 Returning to manual mode ("local").............................................................................588

9.5 How to set up a network and remote control......................................................... 589

COMPANY RESTRICTED

Contents

R&S®FPL1000

9User Manual 1178.3370.02 ─ 14

9.5.1 How to configure a network.........................................................................................589

9.5.2 How to operate the instrument without a network....................................................... 596

9.5.3 How to log on to the network.......................................................................................596

9.5.4 How to share directories (only with Microsoft networks)............................................. 599

9.5.5 How to control the R&S FPL1000 via the web browser interface............................... 600

9.5.6 How to deactivate the web browser interface............................................................. 601

9.5.7 How to set up remote desktop.................................................................................... 602

9.5.8 How to start a remote control session from a PC........................................................608

9.5.9 How to return to manual operation..............................................................................609

10 Remote commands............................................................................610

10.1 Conventions used in SCPI command descriptions............................................... 610

10.2 Common suffixes...................................................................................................... 611

10.3 Common commands.................................................................................................611

10.4 Commands for remote instrument operation.........................................................616

10.5 Selecting the operating mode and application...................................................... 617

10.5.1 Selecting the mode and applications.......................................................................... 617

10.5.2 Performing a sequence of measurements.................................................................. 620

10.5.3 Programming example: performing a sequence of measurements............................ 622

10.6 Configuring and performing measurements.......................................................... 624

10.6.1 Performing measurements..........................................................................................625

10.6.2 Configuring power measurements.............................................................................. 628

10.6.3 Measuring compression points................................................................................... 632

10.6.4 Measuring the channel power and ACLR................................................................... 637

10.6.5 Measuring the carrier-to-noise ratio............................................................................ 655

10.6.6 Measuring the occupied bandwidth.............................................................................656

10.6.7 Measuring the spectrum emission mask.....................................................................658

10.6.8 Measuring spurious emissions....................................................................................689

10.6.9 Analyzing statistics (APD, CCDF)............................................................................... 702

10.6.10 Measuring the time domain power.............................................................................. 713

10.6.11 Measuring the harmonic distortion..............................................................................722

10.6.12 Measuring the third order intercept point.................................................................... 726

10.6.13 Measuring the AM modulation depth.......................................................................... 729

10.6.14 Remote commands for EMI measurements................................................................732

COMPANY RESTRICTED

Contents

R&S®FPL1000

10User Manual 1178.3370.02 ─ 14

10.6.15 List evaluations........................................................................................................... 740

10.6.16 Measuring the pulse power......................................................................................... 744

10.6.17 Programming example: performing a basic frequency sweep.................................... 749

10.7 Remote commands for result displays................................................................... 752

10.7.1 Working with windows in the display...........................................................................752

10.7.2 Examples: configuring the result display.....................................................................759

10.8 Setting basic spectrum RF measurement parameters.......................................... 761

10.8.1 Defining the frequency and span................................................................................ 762

10.8.2 Configuring bandwidth and sweep settings.................................................................772

10.8.3 Configuring the vertical axis (amplitude, scaling)........................................................779

10.8.4 Configuring triggered and gated measurements.........................................................786

10.8.5 Configuring the data input and output......................................................................... 792

10.8.6 Zooming into the display............................................................................................. 816

10.8.7 Configuring the trace display and retrieving trace data...............................................819

10.8.8 Working with markers..................................................................................................845

10.8.9 Configuring display lines............................................................................................. 906

10.8.10 Defining limit checks................................................................................................... 909

10.9 Managing settings and results................................................................................ 926

10.9.1 General data storage and loading commands............................................................ 927

10.9.2 Selecting the items to store.........................................................................................932

10.9.3 Storing and loading instrument settings...................................................................... 936

10.9.4 Storing or printing screenshots................................................................................... 941

10.9.5 Storing measurement results...................................................................................... 950

10.9.6 Test reports................................................................................................................. 952

10.9.7 Examples: managing data...........................................................................................962

10.10 Configuring the R&S FPL1000................................................................................. 966

10.10.1 Configuring the reference frequency...........................................................................966

10.10.2 Calibration and checks................................................................................................967

10.10.3 Working with transducers............................................................................................972

10.10.4 Customizing the screen layout.................................................................................... 976

10.10.5 Remote commands for language settings...................................................................981

10.10.6 Configuring the network and remote control............................................................... 982

10.10.7 Checking the system configuration............................................................................. 986

COMPANY RESTRICTED

Contents

R&S®FPL1000

11User Manual 1178.3370.02 ─ 14

10.10.8 Using service functions............................................................................................... 990

10.10.9 Programming examples for instrument setup............................................................. 992

10.11 Emulating other instruments' commands.............................................................. 993

10.11.1 Setting up instrument emulation..................................................................................993

10.11.2 Reference: GPIB commands of emulated HP models................................................996

10.11.3 Reference: command set of emulated CXA/EXA models.........................................1024

10.12 Using the status register........................................................................................ 1026

10.12.1 General status register commands........................................................................... 1027

10.12.2 Reading out the CONDition part............................................................................... 1028

10.12.3 Reading out the EVENt part......................................................................................1028

10.12.4 Controlling the ENABle part...................................................................................... 1029

10.12.5 Controlling the negative transition part......................................................................1029

10.12.6 Controlling the positive transition part....................................................................... 1030

10.12.7 Service request......................................................................................................... 1030

10.13 Deprecated commands...........................................................................................1039

11 Troubleshooting...............................................................................1041

11.1 Error information.....................................................................................................1041

11.2 Error messages in remote control mode.............................................................. 1042

11.3 Troubleshooting remote operation........................................................................1043

11.4 Miscellaneous troubleshooting hints....................................................................1045

11.5 System recovery..................................................................................................... 1047

11.6 Collecting information for support........................................................................1047

11.7 Contacting customer support................................................................................1049

12 Maintenance, storage, transport and disposal..............................1051

12.1 Cleaning................................................................................................................... 1051

12.2 Changing fuses....................................................................................................... 1051

12.3 Handling batteries...................................................................................................1052

12.4 Storage.....................................................................................................................1052

12.5 Transporting............................................................................................................ 1052

12.6 Disposal................................................................................................................... 1053

List of commands (Spectrum mode)..............................................1054

Index..................................................................................................1073

COMPANY RESTRICTED

Contents

R&S®FPL1000

12User Manual 1178.3370.02 ─ 14

COMPANY RESTRICTED

Safety and regulatory information

R&S®FPL1000

13User Manual 1178.3370.02 ─ 14

1 Safety and regulatory information

The product documentation helps you use the product safely and efficiently. Follow the

instructions provided here and in the following chapters.

Intended use

The product is intended for the development, production and verification of electronic

components and devices in industrial, administrative, and laboratory environments.

Use the product only for its designated purpose. Observe the operating conditions and

performance limits stated in the data sheet.

Where do I find safety information?

Safety information is part of the product documentation. It warns you of potential dan-

gers and gives instructions on how to prevent personal injury or damage caused by

dangerous situations. Safety information is provided as follows:

●In Chapter 1.1, "Safety instructions", on page 13. The same information is provi-

ded in many languages as printed "Safety Instructions". The printed "Safety

Instructions" are delivered with the product.

●Throughout the documentation, safety instructions are provided when you need to

take care during setup or operation.

1.1 Safety instructions

Products from the Rohde & Schwarz group of companies are manufactured according

to the highest technical standards. To use the products safely, follow the instructions

provided here and in the product documentation. Keep the product documentation

nearby and offer it to other users.

Use the product only for its intended use and within its performance limits. Intended

use and limits are described in the product documentation such as the data sheet,

manuals and the printed "Safety Instructions". If you are unsure about the appropriate

use, contact Rohde & Schwarz customer service.

Using the product requires specialists or specially trained personnel. These users also

need sound knowledge of at least one of the languages in which the user interfaces

and the product documentation are available.

Reconfigure or adjust the product only as described in the product documentation or

the data sheet. Any other modifications can affect safety and are not permitted.

Never open the casing of the product. Only service personnel authorized by

Rohde & Schwarz are allowed to repair the product. If any part of the product is dam-

aged or broken, stop using the product. Contact Rohde & Schwarz customer service at

https://www.rohde-schwarz.com/support.

Safety instructions

COMPANY RESTRICTED

Safety and regulatory information

R&S®FPL1000

14User Manual 1178.3370.02 ─ 14

Lifting and carrying the product

The maximum weight of the product is provided in the data sheet. You can lift or carry

the product by yourself, if you can manage the weight on your own. Alternatively, you

can use lifting or transporting equipment. Follow the instructions provided by the equip-

ment manufacturer.

Choosing the operating site

Only use the product indoors. The product casing is not waterproof. Water that enters

can electrically connect the casing with live parts, which can lead to electric shock,

serious personal injury or death if you touch the casing. If Rohde & Schwarz provides

accessories designed for your product, e.g. a carrying bag, you can use the product

outdoors.

Unless otherwise specified, you can operate the product up to an altitude of 2000 m

above sea level. The product is suitable for pollution degree 2 environments where

nonconductive contamination can occur. For more information on environmental condi-

tions such as ambient temperature and humidity, see the data sheet.

Setting up the product

Always place the product on a stable, flat and level surface with the bottom of the prod-

uct facing down. If the product is designed for different positions, secure the product so

that it cannot fall over.

If the product has foldable feet, always fold the feet completely in or out to ensure sta-

bility. The feet can collapse if they are not folded out completely or if the product is

moved without lifting it. The foldable feet are designed to carry the weight of the prod-

uct, but not an extra load.

If stacking is possible, keep in mind that a stack of products can fall over and cause

injury.

If you mount products in a rack, ensure that the rack has sufficient load capacity and

stability. Observe the specifications of the rack manufacturer. Always install the prod-

ucts from the bottom shelf to the top shelf so that the rack stands securely. Secure the

product so that it cannot fall off the rack.

Connecting to power

The product is an overvoltage category II product. Connect the product to a fixed

installation used to supply energy-consuming equipment such as household applian-

ces and similar loads. Keep in mind that electrically powered products have risks, such

as electric shock, fire, personal injury or even death. Replace parts that are relevant to

safety only by original parts, e.g. power cables or fuses.

Take the following measures for your safety:

●Before switching on the product, ensure that the voltage and frequency indicated

on the product match the available power source. If the power adapter does not

adjust automatically, set the correct value and check the rating of the fuse.

●If a product has an exchangeable fuse, its type and characteristics are indicated

next to the fuse holder. Before changing the fuse, switch off the product and dis-

Safety instructions

COMPANY RESTRICTED

Safety and regulatory information

R&S®FPL1000

15User Manual 1178.3370.02 ─ 14

connect it from the power source. How to change the fuse is described in the prod-

uct documentation.

●Only use the power cable delivered with the product. It complies with country-spe-

cific safety requirements. Only insert the plug into an outlet with protective conduc-

tor terminal.

●Only use intact cables and route them carefully so that they cannot be damaged.

Check the power cables regularly to ensure that they are undamaged. Also ensure

that nobody can trip over loose cables.

●If you connect the product to an external power supply, use the one delivered with

the product or recommended in the product documentation. The external power

supply must conform to the country-specific regulations.

●Only connect the product to a power source with a fuse protection of maximum

20 A.

●Ensure that you can disconnect the product from the power source at any time.

Pull the power plug to disconnect the product. The power plug must be easily

accessible. If the product is integrated into a system that does not meet these

requirements, provide an easily accessible circuit breaker at the system level.

Handling batteries safely

The product contains exchangeable or built-in lithium polymer or lithium ion cells or

batteries. The use of the word battery in the following always means all types. Only the

battery contents are potentially hazardous. As long as a battery is undamaged and the

seals remain intact, there is no danger.

Impact, shock or heat can cause damage such as dents, punctures and other deforma-

tions. A damaged battery poses a risk of personal injury. Handle a damaged or leaking

battery with extreme care. Immediately ventilate the area since the battery releases

harmful gases. If you come into contact with the battery fluid, immediately remove all

contaminated clothing. Irritation can occur if the battery fluid comes in contact with your

skin or eyes. Immediately and thoroughly rinse your skin or eyes with water and seek

medical aid.

For safe handling, follow these rules:

●Do not short-circuit the battery.

●Do not mechanically damage the battery. Do not open or disassemble the battery.

●Do not expose the battery to high temperatures such as open flames, hot surfaces

and sunlight.

●Only use the battery with the designated Rohde & Schwarz product.

●Only use the appropriate Rohde & Schwarz charger to charge the batteries. If the

batteries are improperly charged, there is a risk of explosion. For charging and dis-

charging temperature ranges, see the product documentation.

●Replace exchangeable batteries only with the same battery type.

●Store the battery in the product or use the product packaging.

●Dispose of exchangeable batteries separately from normal household waste as

specified by the local waste disposal agency.

Safety instructions

COMPANY RESTRICTED

Safety and regulatory information

R&S®FPL1000

16User Manual 1178.3370.02 ─ 14

If you disregard these rules, you risk serious personal injury or even death due to

explosion, fire or hazardous chemical substances. The product documentation pro-

vides further details.

If exchangeable batteries or products with built-in batteries are defective, contact the

Rohde & Schwarz customer service. Rohde & Schwarz classifies the severity of the

defect. When returning batteries or Rohde & Schwarz products containing batteries,

use a carrier qualified to transport dangerous goods and notify the carrier of this classi-

fication. Follow the carrier’s transport stipulations in line with IATA-DGR, IMDG-Code,

ADR or RID.

Using headphones

Take the following measures to prevent hearing damage. Before using headphones,

check the volume and reduce it if necessary. If you monitor varying signal levels, take

off the headphones and wait until the signal has settled. Then adjust the volume.

Cleaning the product

Use a dry, lint-free cloth to clean the product. When cleaning, keep in mind that the

casing is not waterproof. Do not use liquid cleaning agents.

Meaning of safety labels

Safety labels on the product warn against potential hazards.

Potential hazard

Read the product documentation to avoid personal injury or product damage.

Electrical hazard

Indicates live parts. Risk of electric shock, fire, personal injury or even death.

Hot surface

Do not touch. Risk of skin burns. Risk of fire.

Protective conductor terminal

Connect this terminal to a grounded external conductor or to protective ground. This connec-

tion protects you against electric shock if an electric problem occurs.

1.2 Labels on R&S FPL1000

Labels on the casing inform about:

●Personal safety, see "Meaning of safety labels" on page 16

●Product and environment safety, see Table 1-1

●Identification of the product, see Chapter 4.2.2.14, "Device ID", on page 48

Labels on R&S FPL1000

COMPANY RESTRICTED

Safety and regulatory information

R&S®FPL1000

17User Manual 1178.3370.02 ─ 14

Table 1-1: Labels regarding R&S

FPL1000 and environment safety

Labeling in line with EN 50419 for disposal of electrical and electronic equipment after the prod-

uct has come to the end of its service life.

For more information, see "Disposing electrical and electronic equipment" on page 1053.

Labeling in line with directive 2006/66/EC for disposal of batteries after they have come to the

end of their service life.

For more information, see "Disposing electrical and electronic equipment" on page 1053.

1.3 Warning messages in the documentation

A warning message points out a risk or danger that you need to be aware of. The sig-

nal word indicates the severity of the safety hazard and how likely it will occur if you do

not follow the safety precautions.

CAUTION

Potentially hazardous situation. Could result in minor or moderate injury if not avoided.

NOTICE

Potential risks of damage. Could result in damage to the supported product or to other

property.

1.4 Korea certification class A

이 기기는 업무용(A급) 전자파 적합기기로서 판매자 또는 사용자는 이 점을 주의하시기

바라며, 가정외의 지역에서 사용하는 것을 목적으로 합니다.

Korea certification class A

COMPANY RESTRICTED

Documentation overview

R&S®FPL1000

18User Manual 1178.3370.02 ─ 14

2 Documentation overview

This section provides an overview of the R&S FPL1000 user documentation. Unless

specified otherwise, you find the documents at:

www.rohde-schwarz.com/manual/FPL1000

2.1 Getting started manual

Introduces the R&S FPL1000 and describes how to set up and start working with the

product. Includes basic operations, typical measurement examples, and general infor-

mation, e.g. safety instructions, etc.

A printed version is delivered with the instrument. A PDF version is available for down-

load on the Internet.

2.2 User manuals and help

Separate user manuals are provided for the base unit and the firmware applications:

●Base unit manual

Contains the description of all instrument modes and functions. It also provides an

introduction to remote control, a complete description of the remote control com-

mands with programming examples, and information on maintenance, instrument

interfaces and error messages. Includes the contents of the getting started manual.

●Firmware application manual

Contains the description of the specific functions of a firmware application, includ-

ing remote control commands. Basic information on operating the R&S FPL1000 is

not included.

The contents of the user manuals are available as help in the R&S FPL1000. The help

offers quick, context-sensitive access to the complete information for the base unit and

the firmware applications.

All user manuals are also available for download or for immediate display on the Inter-

net.

2.3 Service manual

Describes the performance test for checking compliance with rated specifications, firm-

ware update, troubleshooting, adjustments, installing options and maintenance.

The service manual is available for registered users on the global Rohde & Schwarz

information system (GLORIS):

https://gloris.rohde-schwarz.com

Service manual

COMPANY RESTRICTED

Documentation overview

R&S®FPL1000

19User Manual 1178.3370.02 ─ 14

2.4 Instrument security procedures

Deals with security issues when working with the R&S FPL1000 in secure areas. It is

available for download on the internet.

2.5 Printed safety instructions

Provides safety information in many languages. The printed document is delivered with

the product.

2.6 Data sheets and brochures

The data sheet contains the technical specifications of the R&S FPL1000. It also lists

the firmware applications and their order numbers, and optional accessories.

The brochure provides an overview of the instrument and deals with the specific char-

acteristics.

See www.rohde-schwarz.com/brochure-datasheet/FPL1000

2.7 Release notes and open source acknowledgment

(OSA)

The release notes list new features, improvements and known issues of the current

firmware version, and describe the firmware installation.

The software makes use of several valuable open source software packages. An open-

source acknowledgment document provides verbatim license texts of the used open

source software.

See www.rohde-schwarz.com/firmware/FPL1000

2.8 Application notes, application cards, white papers,

etc.

These documents deal with special applications or background information on particu-

lar topics.

See www.rohde-schwarz.com/application/FPL1000

Application notes, application cards, white papers, etc.

COMPANY RESTRICTED

Documentation overview

R&S®FPL1000

20User Manual 1178.3370.02 ─ 14

2.9 Video tutorials

Video tutorials that show you how to get started and perform basic tasks with the

R&S FPL1000 are available on the Rohde & Schwarz internet site:

https://www.rohde-schwarz.com/manual/r-s-fpl1000-trying-out-basic-measurement-

tasks-manuals_78701-567115.html

2.10 Calibration certificate

The document is available on https://gloris.rohde-schwarz.com/calcert. You need the

device ID of your instrument, which you can find on a label on the rear panel.

Calibration certificate

COMPANY RESTRICTED

Page is loading ...