Bticino 4073 Operating instructions

Brand: Bticino

Model: 4073

Type: Operating instructions

Bticino 4073 is an outdoor siren with a flashing light, designed to provide both audible and visual alerts for security systems. It features a self-contained battery for uninterrupted operation in case of power outages, ensuring continuous protection even during emergencies. The siren is easy to install and can be configured to work with various power supply options, including E46ADCN, E49, and E47ADCN. It is protected against removal and opening, providing enhanced security and peace of mind.

Page is loading ...

OUTDOOR SIREN WITH FLASH

OUTDOOR SIREN INSTALLATION

• Unscrew the 4 screws (1) and remove the external cover (2).

• Fit the cover and screw the four fastening screws (1) to the base on the wall.

• Using the drilling template (3), position the hole (4) by the wires out pipe,

and mark the 4 holes for the fastening screws (5), the hole for the tamper

screw (6) and the hole for the anti-tamper fastening (7) (Patent Pending).

NOTE: drill the holes using a Ø 6 mm drill bit.

•

Insert the plastic plugs into the holes.

• Break the hole cut-out (11) to insert the screw of the anti-tamper system

• Partially screw the two top screws and attach there the siren

(8).

• Screw the two bottom screws (9). Tighten all four fastening screws and the

screw of the anti-tamper system

Wall

Acoustic and optical outdoor warning designed to

contain the self-supply battery.

Acoustic

signaller

Optical

signaller

Cable

passage

The MAX at the input terminals:

- normal operation

- alarm

- battery charging with E47ADCN

with E46ADCN/E49

20 mA

50 mA

250 mA

Input/output and power supply Two wire

Housing for 12V battery 2.0 – 7.2 Ah

Alarm autonomy 15 min

Alarm sound intensity

105 dB(A) at 1 m.

Frequency 1500 Hz

Flashing LED

Flashes per minute 60

Weight (without battery) 2.1 Kg

IP degree of protection IP44

Room operating temperature (-25) – (+55) °C

Self-protected against removal and

opening

YES

Protection index against mechanical

impact IK

IK08

Features

Cut-outs for

installation

with pipes on

surface

•

Screw the tamper screw (10); if the device is being installed on an uneven

surface avoid excessive tightening.

•

Insert the battery in its housing without connecting the Faston clamps. For

the type of battery see the following table:

•

Connect the supply cable pair (BUS) to the appropriate clamps of the

internal card (see following page).

• Connect the battery connectors only with powered BUS.

Power supply Main battery Secondary battery

E49 7 Ah 7 Ah (*)

E46ADCN 7 Ah 7 Ah (*)

E47ADCN 2 Ah 2 Ah

(*) If the second siren is installed in order to have an additional signalling and it

is not necessary to extend the system autonomy in back-up mode (no network

supply), it is possible to install a 2Ah battery.

Battery

housing

Siren ash LED

Before performing any actions on the siren, make sure that the

system is in maintenance mode.

The ashing of the siren ash LED when exiting maintenance

mode indicates an inversion of the BUS polarity.

If the red BUS LED comes on, invert the polarity of the BUS.

Not compatible with sirens 4072A/4072L.

If a second siren is installed as part of the system, the installation

of another 4073 is also required.

LED ON OFF

Green power supply

LED

Power supply active Power supply disabled

Red BUS LED BUS polarity inverted BUS polarity correct

Red battery LED

Battery polarity

inverted

Battery polarity correct

LED notications

Type of power

supply

Second siren

Foam

protection

enable

Foam sensors

Power supply LED

BUS LED

Battery LED

Removable clamp for BUS connection

Battery

connector

LED and conguration switch:

Main siren Secondary siren

System with

E46ADCN or

E49 power

supply

SW1 SW2

1 2 3 4

SW1 SW2

1 2 3 4

In case of primary network power supply interruption, system autonomy is ensured by

the battery installed inside the siren itself.

This solution means that only one battery can be used, instead of the two normally

used in traditional systems, therefore reducing maintenance and increase system

reliability by keeping safety levels unchanged.

Congure the siren as shown above.

If a higher degree of system autonomy is

desired, a second siren can be installed on

the system, congured as shown above.

System with

E47ADCN

power supply

SW1 SW2

1 2 3 4

SW1 SW2

1 2 3 4

It’s presence is useful for notication purposes, but is however not compulsory, as the

system back-up battery will be connected to the power supply unit.

The internal housing of the siren houses the siren self-powering battery itself. A 2 Ah

battery will therefore suce.

Congure this siren as shown above.

If a second siren is desired, in order to have

two notication points, a second siren can

be installed on the same system, congured

as shown above.

Foam

protection

SW1 SW2

1 2 3 4

The foam protection can be enabled using the SW2 conguration switch.

SW2 = ON (Foam protection enabled)

Bring the central unit into “Maintenance” and disconnect batteries and SCS bus to modify the conguration.

Page is loading ...

Bticino 4073 Operating instructions

Brand: Bticino

Model: 4073

Type: Operating instructions

Download PDF

report

in other languages

italiano: Bticino 4073 Istruzioni per l'uso
français: Bticino 4073 Mode d'emploi
español: Bticino 4073 Instrucciones de operación
Deutsch: Bticino 4073 Bedienungsanleitung
Nederlands: Bticino 4073 Handleiding
português: Bticino 4073 Instruções de operação

Bticino 4073 Operating instructions

Bticino 4073 Operating instructions

in other languages

Related papers

Other documents