Page is loading ...
Page is loading ...
3
EN
OUTDOOR SIREN WITH FLASH
OUTDOOR SIREN INSTALLATION
• Unscrew the 4 screws (1) and remove the external cover (2).
1
1
1
2
1
• Fit the cover and screw the four fastening screws (1) to the base on the wall.
1
1
1
1
• Using the drilling template (3), position the hole (4) by the wires out pipe,
and mark the 4 holes for the fastening screws (5), the hole for the tamper
screw (6) and the hole for the anti-tamper fastening (7) (Patent Pending).
NOTE: drill the holes using a Ø 6 mm drill bit.
•
Insert the plastic plugs into the holes.
• Break the hole cut-out (11) to insert the screw of the anti-tamper system
.
• Partially screw the two top screws and attach there the siren
(8).
• Screw the two bottom screws (9). Tighten all four fastening screws and the
screw of the anti-tamper system
.
Wall
8
9
4
3
5
5
6
7
Acoustic and optical outdoor warning designed to
contain the self-supply battery.
Acoustic
signaller
Optical
signaller
Cable
passage
The MAX at the input terminals:
- normal operation
- alarm
- battery charging with E47ADCN
with E46ADCN/E49
20 mA
20 mA
50 mA
250 mA
Input/output and power supply Two wire
Housing for 12V battery 2.0 – 7.2 Ah
Alarm autonomy 15 min
Alarm sound intensity
105 dB(A) at 1 m.
Frequency 1500 Hz
Flashing LED
Flashes per minute 60
Weight (without battery) 2.1 Kg
IP degree of protection IP44
Room operating temperature (-25) – (+55) °C
Self-protected against removal and
opening
YES
Protection index against mechanical
impact IK
IK08
Features
Cut-outs for
installation
with pipes on
surface
•
Screw the tamper screw (10); if the device is being installed on an uneven
surface avoid excessive tightening.
•
Insert the battery in its housing without connecting the Faston clamps. For
the type of battery see the following table:
•
Connect the supply cable pair (BUS) to the appropriate clamps of the
internal card (see following page).
• Connect the battery connectors only with powered BUS.
Power supply Main battery Secondary battery
E49 7 Ah 7 Ah (*)
E46ADCN 7 Ah 7 Ah (*)
E47ADCN 2 Ah 2 Ah
(*) If the second siren is installed in order to have an additional signalling and it
is not necessary to extend the system autonomy in back-up mode (no network
supply), it is possible to install a 2Ah battery.
10
Battery
housing
Siren ash LED
11
4
Before performing any actions on the siren, make sure that the
system is in maintenance mode.
The ashing of the siren ash LED when exiting maintenance
mode indicates an inversion of the BUS polarity.
If the red BUS LED comes on, invert the polarity of the BUS.
Not compatible with sirens 4072A/4072L.
If a second siren is installed as part of the system, the installation
of another 4073 is also required.
LED ON OFF
Green power supply
LED
Power supply active Power supply disabled
Red BUS LED BUS polarity inverted BUS polarity correct
Red battery LED
Battery polarity
inverted
Battery polarity correct
LED notications
Type of power
supply
Second siren
Foam
protection
enable
Foam sensors
Power supply LED
BUS LED
Battery LED
Removable clamp for BUS connection
Battery
connector
LED and conguration switch:
Main siren Secondary siren
System with
E46ADCN or
E49 power
supply
SW1 SW2
1 2 3 4
SW1 SW2
1 2 3 4
In case of primary network power supply interruption, system autonomy is ensured by
the battery installed inside the siren itself.
This solution means that only one battery can be used, instead of the two normally
used in traditional systems, therefore reducing maintenance and increase system
reliability by keeping safety levels unchanged.
Congure the siren as shown above.
If a higher degree of system autonomy is
desired, a second siren can be installed on
the system, congured as shown above.
System with
E47ADCN
power supply
SW1 SW2
1 2 3 4
SW1 SW2
1 2 3 4
It’s presence is useful for notication purposes, but is however not compulsory, as the
system back-up battery will be connected to the power supply unit.
The internal housing of the siren houses the siren self-powering battery itself. A 2 Ah
battery will therefore suce.
Congure this siren as shown above.
If a second siren is desired, in order to have
two notication points, a second siren can
be installed on the same system, congured
as shown above.
Foam
protection
SW1 SW2
1 2 3 4
The foam protection can be enabled using the SW2 conguration switch.
SW2 = ON (Foam protection enabled)
Bring the central unit into “Maintenance” and disconnect batteries and SCS bus to modify the conguration.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
