Horstmann C-Stat 11-ZW User guide

Category
Thermostats
Type
User guide
C-Stat 11-ZW
User Instructions
24 Hour Wireless Programmable Room
Thermostat and ASR-ZW Receiver
Programmable room thermostats are widely recognised as one
of the best ways in which to control central heating. Horstmann
C-Stat programmable room thermostats have a large display
and intuitive user interface, making them easy to set up and use.
C-Stat uses a sophisticated time proportional integral (TPI)
algorithm for accurate temperature control and energy
efficiency.
1
What is a programmable room thermostat?
...an explanation for householders.
A programmable room thermostat is both a programmer and a
room thermostat. A programmer allows you to set 'ON and OFF'
time periods to suit your own lifestyle. A room thermostat works
by sensing the air temperature, switching on the heating when
the air temperature falls below the thermostat setting and
switching it off once the set temperature has been reached.
So, a programmable room thermostat lets you choose what
times you want the heating to be on, and what temperature it
should reach while it is on. It will allow you to select different
temperatures in your home at different times of the day (and
days of the week) to meet your particular needs.
Turning a programmable room thermostat to a higher setting will
not make the room heat up any faster. How quickly the room
heats up depends on the design of the heating system, for
example, the size of the boiler and radiators. Neither does the
setting affect how quickly the room cools down. Turning a
programmable room thermostat to a lower setting will result in
the room being controlled at a lower temperature, and saves
energy.
The way to set and use your programmable room thermostat is
to find the lowest temperature settings that you are comfortable
with at the different times you have chosen, and then leave it
alone to do its job. The best way to do this is to set low
temperatures first, say 18ºC and then turn them up by one
degree each day until you are comfortable with the
temperatures. You won't have to adjust the thermostat further.
Any adjustments above these settings will waste energy and
cost you more money.
2
If your heating system is a boiler with radiators, there will usually
be only one programmable room thermostat to control the whole
house. But you can have different temperatures in individual
rooms by installing thermostatic radiator valves (TRVs) on
individual radiators. If you don't have TRVs, you should choose
a temperature that is reasonable for the whole house. If you do
have TRVs, you can chose a slightly higher setting to make sure
that even the coldest room is comfortable, then prevent any
overheating in other rooms by adjusting the TRVs.
The time on the programmer must be correct. Some types have
to be adjusted in spring and autumn at the changes between
Greenwich Mean Time and British Summer Time.
You may be able to temporarily adjust the heating programme,
for example, 'Override', 'Advance' or 'Boost'. These are
explained in the manufacturer's instructions.
Programmable room thermostats need a free flow of air to sense
the temperature, so they must not be covered by curtains or
blocked by furniture. Nearby electric fires, televisions, wall or
table lamps may prevent the thermostat from working properly.
OVERVIEW EXPLANATION FOR HOUSEHOLDER
Your installer has made an excellent choice and installed one of
the very latest programmable room thermostats manufactured
by Horstmann of Bristol.
Full of the latest technology, the C-Stat has been designed to be
simple to use and adjust whilst still giving accurate energy
saving control over your heating system.
Communication between the thermostat and it's receiver is by Z
Wave wireless RF technology which avoids the need for
additional wiring.
3
Actual Room
Temperature
Day of
Week
Time of
Day
Until (Time)
Then (Temp)
Enter
Button
+ Button- ButtonBack
Button
Set
Temperature
Antenna
Symbol
4
DISPLAY
C-Stat 11-ZW
DISPLAY
Actual Room Temperature This is the actual room temperature
measured by the C-Stat
Set Temperature This is the temperature that the C-Stat
will allow the room to reach. The
temperature range can be set between
5°C and 30°C
When the temperature shown in the
display is achieved the C-Stat will switch
the heating OFF.
If the temperature in the room falls below
the setting the C-Stat will switch the
heating ON.
Until (time) This is the time that the next
temperature setting is due to operate
Then (temp) This is the temperature setting that is
due to operate next
Day of the week It is important that the correct day of the
week shows in the display
Time of day This is the current time of day
Setting Buttons Press any button to illuminate the
display.
The message 'To override press -/+ To
see menu press ENTER' will appear
No Radio Waves Wireless connection not set up
Solid Radio Antenna Z- Wave c ommunication present
– Flashing Radio Antenna – Temporary
loss of Z-Wave communication
ACTIVATING THE BACK-LIT DISPLAY
Press any button to illuminate the display. This will remain illuminated for
10 seconds
GENERAL INFORMATION
During programming please note that the display will return to its normal
operating screen if the last button press exceeds 10 seconds.
5
TEMPORARY OVERRIDE
A temporary temperature change can be made at any time. It is
also possible to extend how long this temperature override is in
operation.
The temperature will revert to its normal programmed setting at
the next timed temperature change
TEMPORARY OVERRIDE WITH TIME EXTENSION
(Maximum of 4 hours)
The temperature will revert to its normal programmed setting
at the next timed temperature change.
Press ‘-’ or ‘+’ to
adjust temperature
New temperature
setting will be shown
on the display
Press ‘-’ or ‘+’ to
adjust temperature
New temperature
setting will be
shown on the
display
Press ENTER
Press ‘+’ to
adjust the time
Press ENTER
6
The hours of
the UNTIL time
will flash
PERMANENT OVERRIDE
In the 'HOLD' position the temperature can be overridden by
pressing either the '-' or '+' buttons. This will then become the
new 'HOLD' temperature
PERMANENT OVERRIDE CANCELLATION
Press ‘-’ or ‘+’ to
adjust temperature
New temperature
setting will be
shown on the
display
Press ENTER
The hours of
the UNTIL time
will flash
Press ENTER
Press the '+'
repeatedly until
HOLD appears in
the display
Message will
appear briefly
confirming
'Temperature set
until manual
release'
Press BACK
Press ENTER
7
SETTING UP THE C-STAT
Upon initial installation the C-Stat has the following factory
default settings
Time Target Temperature
Period 1 06:00 am 20 °C
Period 2 08:30 am 18 °C
Period 3 11:30 am 20 °C
Period 4 01:30 pm 18 °C
Period 5 05:00 pm 21 °C
Period 6 10:00 pm 15 °C
These can be changed by the installer or the end user at
any time by accessing the MAIN MENU
8
MAIN MENU
To access the MAIN MENU take the following steps:
MENU OPTIONS
Press ENTER twice
Press '-' or '+' to
toggle between the
menu options
Programme This allows the user to adjust the different
time and temperature settings from the
factory default settings shown in the table
on page 8.
Up to six different temperature levels can be
set in any 24 hour period
Standby This puts the C-Stat into Frost protection or
Standby condition and allows the heating to
be permanently switched off but will activate
and switch the heating on if the temperature
in the house falls below the standby
temperature set.
All programme settings are overridden and
the unit will not return to normal operation
until the standby period has ended by
pressing the ENTER button.
Holiday This puts the C-Stat into a temporary
standby mode with a start and end date
which can be set to coincide with a holiday
period. At the end of the set period the C-
Stat will resume normal operation
Time / Date The C-Stat has a built in clock and calendar.
This will require setting on initial installation.
If this has not been set on installation
please go to Setting the TIME and DATE
section on page 14 before continuing
Set Up Enables the programming of various options
outlined in the SET UP MENU on page 15
of these instructions – These should be set
on installation.
9
Setting the PROGRAMME
Six time and temperature settings are available in each 24 hour period.
Pressing BACK at any time in this process will return you to normal
operating mode.
If only two different temperature settings are required in 24 hours then set
the first time and temperature using programme one (P1) and the second
time and temperature setting using programme setting two (P2). The
remaining programmes (P3 to P6) should all be set to the same time and
temperature as P2.
This same method can be used if three, four or five temperature levels are
required, always using the first settings to provide the temperature change
commands with the remaining settings that are not required set to the same
time and temperature as the last required setting.
Press ENTER
three times
Press ENTER
Time / Temperature
setting P1 will flash
Press '-' or '+' to
select time /
temperature period
you wish to set (P1
to P6)
Temperature will
flash, use the '-' or
'+' to select the
required
temperature
Press ENTER
The hours START
time will flash
Press '-' or '+' to
adjust the hours
then press ENTER.
The minutes will
then flash.
If you require to set further periods for
the same day, the next period will now
automatically flash. Follow this process
again to programme as required
10
On completion of
Period 6 (P6) press
BACK to return to
normal operating
mode.
Press '-' or '+' to
adjust the
minutes the
press ENTER
Setting the STANDBY
To exit STANDBY mode, press ENTER TWICE
Press ENTER Twice
The words STANDBY and
Standby Enabled will appear
on the display
Press ENTER
After a short period Standby
Enabled will disappear from
the display
Press '-' or '+' until
STANDBY
appears on the
display
11
Setting the HOLIDAY programme
Pressing BACK at any time in this process will return you to
normal operating mode
Press ENTER twice
The START date
will now flash
Press ENTER
Press the '-' or '+' to
adjust to the date you
wish the holiday
programme to start.
Pressing ENTER to
change between Day,
Month and Year
Press '-' or '+' until
HOLIDAY appears
on the display
The BACK date
will now flash
Again, Press the '-' or '+' to
adjust to the date you wish
the holiday programme to
end. Pressing ENTER to
change between Day,
Month and Year
12
HOLIDAY
programme is now
set
If the holiday period START date matches today's date, the
STANDBY temperature will be shown on the display together
with the suitcase icon.
If the holiday period START date does not match today's date
the display will remain in normal operating mode but with the
suitcase icon appearing on the right of the display. Indicating a
holiday period is pending
To cancel a set holiday programme in ADVANCE of its
activation, re-programme using the above procedure and set
the START date and BACK date to today's date.
To cancel a set holiday programme during activation press
ENTER button twice, the unit will return to normal operating
mode and the suitcase icon will disappear.
THE DATES SPECIFIED BECOME EFFECTIVE FROM
MIDNIGHT OF THE DAY ENTERED
13
Setting the TIME and DATE
Pressing BACK at any time in this process will return you to
normal operating mode
If an incorrect date is entered the wrong day will appear in the
normal operating screen.
Press ENTER twice
The hours for
the time of day
will flash
Press ENTER
Press '-' or '+' to
adjust hours then
press ENTER
Press '-' or '+' until
Time/Date appears
on the display
The minutes for
the time of day
will flash
Press '-' or '+' to
adjust minutes
then press
ENTER
The day of the
date will now
flash
Press '-' or '+' to adjust
the day to match
today's date Pressing
ENTER to change
between Day, Month
and Year
Time and Date are
both set and the unit
will return to normal
operating mode
14
SETUP MENU
To access the SET UP MENU take the following steps:
MENU OPTIONS
Press ENTER twice
Press ENTER
Press '-' or '+' to
toggle between the
menu options
detailed below
Press '-' or '+' until
Set Up appears on
the display
Select clock format This allows the display to show the time in
24 hour or AM/PM format
Daylight saving This is the adjustment made in the UK when
the clocks go back or forward in the Autumn
and Spring.
When using the C-Stat in the UK the
daylight saving ON setting should be
selected which will automatically adjust the
GMT/BST times accordingly
Standby temperature This is the temperature setting used when in
Standby or Holiday mode (Min 5°C / Max
30°C)
In cold weather the heating will activate if
the temperature being measured falls below
this temperature setting.
Lower temperature limit This sets the lowest temperature setting the
C-Stat will allow to be programmed.
The default setting is 5°C
Upper temperature limit This sets the highest temperature setting
the C-Stat will allow to be programmed
The default setting is 30°C
15
TPI cycles per hour This setting helps the TPI energy saving
software to operate correctly depending on
the type of heating system you have
Optimum start This calculates the amount of time the C-
Stat may need to switch on in advance of
the next target temperature setting in order
to meet the requirement.
Tamper setting This setting allows a 4 digit release code to
be set up to stop unauthorised adjustments
being made in multi occupancy buildings.
Set up Z-Wave Wireless connection to receiver
MENU OPTIONS (Contd...)
Setting the SELECT CLOCK FORMAT
Pressing BACK at any time in the process will return you to
normal operating mode
Press ENTER twice
Press ENTER
Press '-' or '+' until
Select clock format
appears on the
display
Press '-' or '+' until
Set Up appears on
the display
Press ENTER
Either 'Select clock
24 hr' or 'Select
clock AM/PM' will
appear
Press '-' or '+' to
toggle between
the two options
Select your choice
by pressing ENTER
The unit will now
return to the Set up
position, simply
press BACK to
return to normal
operating mode
16
Setting the DAYLIGHT SAVING
Pressing BACK at any time in this process will return you to
normal operating mode
The default factory setting is for the Daylight saving to be ON
giving automatic switching to GMT/BST
Press ENTER twice
Press ENTER
Press '-' or '+' until
Daylight saving
appears on the
display
Press '-' or '+' until
Set Up appears on
the display
Press ENTER
Either 'Daylight
Saving Off' or
'Daylight Saving On'
will appear on the
display
Press '-' or '+' to
toggle between
the two options
Select your choice
by pressing ENTER
The unit will now
return to the Set up
position, simply
press BACK to
return to normal
operating mode
17
Set ting the STAND BY TEMP ERATURE, LOWER
TEMPERATURE LIMIT or UPPER TEMPERATURE LIMIT
Pressing BACK at any time in this process will return you to
normal operating mode
Press ENTER twice
Press ENTER
Press '-' or '+' until
the required option
appears on the
display
Press '-' or '+' until
Set Up appears on
the display
Press ENTER
The temperature
setting will now
flash
Press '-' or '+' to
adjust temperature
then press ENTER
The unit will now return to the
Set Up position, simply press
BACK to return to normal
operating mode
18
Setting the TPI cycles
Pressing the BACK at any time in this process will return you to
normal operating mode
Oil Boilers 3 cycles per hour
Gas Boilers 6 cycles per hour
Not used 9 cycles per hour
Electric Heating 12 cycles per hour
This feature would normally be set by your installer
Press ENTER twice
Press ENTER
Press '-' or '+' until
TPI Cycles per hour
appears on the
display
Press '-' or '+' until
Set Up appears on
the display
Press ENTER
The current setting
will now flash
Press '-' or '+' to
adjust to the correct
setting for your
heating system.
(Please refer to
table below)
The unit will now
return to the Set Up
position, simply press
BACK to return to
normal operating
mode
Press ENTER
19
Setting the OPTIMUM START
This setting will allow the C-Stat to anticipate the next set
temperature and switch on up to two hours in advance to ensure
room temperature has been reached by the time the new set
temperature applies.
As a consequence the switch on time could take place anywhere
between 2 hours and zero before the set time and temperature.
With the optimum start set to OFF the user will need to anticipate
the warm up time needed in the programme settings. (Typically
the set temperature will be set approx. 1 hour in advance of
when it is required)
Pressing the BACK at any time in this process will return you to
normal operating mode
This feature would normally be set by your installer.
Press ENTER twice
Press ENTER
Press '-' or '+' until
Optimum Start
appears on the
display
Press '-' or '+' until
Set Up appears on
the display
Select YES or NO
and press ENTER
to confirm
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Horstmann C-Stat 11-ZW User guide

Category
Thermostats
Type
User guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI