Gossen MetraWatt U180B Operating instructions

Software Descripton

SOFTWARE M-BUS MASTER

For M-Bus Communication Module

3-349-657-03

1/11.11

M-BUS Master

M-BUS

Multilingual Manual

November Edition 2011

Haftungsbegrenzung

Der Hersteller behält sich das Recht vor, jederzeit und ohne Vorankündung, das Gerät oder dessen in diesem Handbuch beschriebenen

Spezifikationen zu ändern. Jede, auch die auszugsweise und nicht schriftlich vom Hersteller genehmigte Vervielfältigung des

Handbuchs durch Fotokopie oder mit anderen Systemen auch elektronsicher Art, verletzt das Urheberrecht und wird strafrechtlich

verfolgt.

Es ist strengstens verboten, das Gerät für andere Zwecke als die zu verwenden, für die es hergestellt wurde und die sich dem

Inhalt des vorliegenden Handbuchs entnehmen lassen. Während der Anwendung der Funktionen des vorliegenden Geräts immer

sicherstellen, dass alle Rechte sowie die Privatsphäre und die Rechte Dritter eingehalten werden.

AUSSER FÜR DIE GESETZLICH AUFERLEGTEN EINSCHRÄNKUNGEN HAFTET DER HERSTELLER IN KEINEM FALL FÜR SCHÄDEN,

DIE AUS DEM PRODUKT RESULTIEREN UND ER ÜBERNIMMT KEINERLEI ANDEREN PFLICHTEN ODER HAFTUNGEN, ALS

AUSDRÜCKLICH OBEN GENANNT UND BEFUGT AUCH KEINEN VERTRETER ODER ANDERE PERSON IN DIESEM SINNE.

Alle in diesem Handbuch genannten Marken sind Eigentum der jeweiligen Inhaber.

Die in diesem Handbuch enthaltenen Informationen dienen der Information und können ohne Vorankündigung verändert werden.

Sie sind für den Hersteller nicht bindend. Der Hersteller haftet nicht für Fehler oder Unstimmigkeiten, die in diesem Handbuch

vorhanden sein können.

Gedruckt in Italien.

Limitation of Liability

The Manufacturer reserves the right to modify the specifications in this manual without previous warning. Any copy of this manual, in

part or in full, whether by photocopy or by other means, even of electronic nature, without the manufacture giving written authorisation,

breaches the terms of copyright and is liable to prosecution.

It is absolutely forbidden to use the device for different uses other than those for which it has been devised for, as inferred to in this

manual. When using the features in this device, obey all laws and respect privacy and legitimate rights of others.

EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, UNDER NO CIRCUMSTANCES SHALL THE MANUFACTURER BE

LIABLE FOR CONSEQUENTIAL DAMAGES SUSTAINED IN CONNECTION WITH SAID PRODUCT AND THE MANUFACTURER NEITHER

ASSUMES NOR AUTHORIZES ANY REPRESENTATIVE OR OTHER PERSON TO ASSUME FOR IT ANY OBBLIGATION OR LIABILTY

OTHER THAN SUCH AS IS EXPRESSLY SET FORTH HEREIN.

All trademarks in this manual are property of their respective owners.

The information contained in this manual is for information purposes only, is subject to changes without previous warning and cannot

be considered binding for the Manufacturer. The Manufacturer assumes no responsabilty for any errors or incoherence possibly

contained in this manual.

Printed in Italy.

Limitazione di responsabilità

Il Produttore si riserva il diritto di modificare, senza preavviso, le specifiche illustrate in questo manuale. Qualunque duplicazione del

manuale, parziale o totale, non autorizzata per iscritto dal Produttore, ottenuta per fotocopiatura o con altri sistemi, anche di natura

elettronica, viola le condizioni di copyright ed è giuridicamente perseguibile.

E’ assolutamente proibito utilizzare il dispositivo per usi differenti da quelli per cui è stato costruito, desumibili dal contenuto del

presente manuale. Durante l’uso delle funzioni del presente dispositivo, assicurarsi di rispettare tutte le leggi, nonchè la privacy ed

i diritti altrui.

ECCETTO PER I LIMITI IMPOSTI DALLA LEGGE, IN NESSUN CASO IL PRODUTTORE SARA’ RESPONSABILE PER DANNI DERIVANTI

DAL PRODOTTO, NE’ SI ASSUME O AUTORIZZA ALCUN RAPPRESENTANTE O ALTRA PERSONA AD ASSUMERSI QUALUNQUE

OBBLIGO O RESPONSABILITA’ DIVERSE DA QUELLE DICHIARATE ESPRESSAMENTE SOPRA.

Tutti i marchi, citati in questo manuale, sono proprietà dei rispettivi possessori.

Le informazioni contenute in questo manuale hanno unicamente scopo informativo, sono soggette a variazioni senza preavviso e non

potranno venire considerate impegnative per il Produttore. Il Produttore non assume alcuna responsabilità per eventuali errori o

incoerenze che possano essere contenuti nel manuale.

Stampato in Italia.

Page is loading ...

USER MANUAL

English

CONTENT

1. Environment setup and installation .................................21

1.1 System requirements .........................................................21

1.2 Installation ..........................................................................21

1.3 Start the application ...........................................................21

2. Using M-BUS MASTER ......................................................22

2.1 Add an energy counter by automatic procedure .................23

2.2 Add an energy counter by manual procedure .....................27

2.3 Energy counter management .............................................29

2.3.1. Device Information ................................................................................................29

2.3.2. Device Setup .........................................................................................................30

2.3.3. Device Commands.................................................................................................31

2.3.4. Device Data ...........................................................................................................33

2.4 Remove an energy counter .................................................34

M-BUS Master 21

English

1. Environment setup and installation

1.1 System requirements

•WindowsXPServicePack3,Windows7(32–64bit)

•Microsoft.NETFramework3.5

1.2 Installation

Toinstallthisapplication,runtheM-BUS Master Setup.exeinstallationpackagefile,containedintheCD

ROM.FollowtheinstructionsshownonPCtoinstallwithsuccesstheapplication.

1.3 Start the application

ToruntheM-BUSMASTER,clickonthedesktopiconcreatedduringtheinstallationprocess,orclickthe

executablefile(M-BUS Master.exe)containedinthefolderselectedduringtheinstallationprocess.

22 M-BUS Master

English

2. Using M-BUS MASTER

WhenM-BUSMASTERstarts,thefollowingpageisdisplayed.

Pict.1–M-BUSMasterStartPage

 Itallowstoaddanenergycounter.

 Removetheselectedenergycounter.

 ItallowstoselecttheM-BUSMASTERlanguage(English,German,Italian,French).

 AninformationwindowaboutM-BUSMASTER(version,copyright)isdisplayed.

M-BUS Master 23

English

2.1 Add an energy counter by automatic procedure

ThefollowingdescriptionshowshowtoaddanewenergycountercombinedtoanM-BUSmodulebyautomatic

procedure.

ClickonApplication setupitemintheleftcolumn.Thefollowingparametersareshown.

Pict.2–Serialcommunicationsettings

SelectthePCPortwheretheM-BUSmoduleisconnectedandtherelevantcommunicationspeed(Baudrate).

ConfirmwithApplykey.

24 M-BUS Master

English

Afterserialport setup, click on Network discover item in the left column. The following parameters are

shown.

Pict.3–Networkdiscoverpage

InthispageitispossiblediscoveringtheM-BUScommunicationmoduleconnectedontheM-BUSnetwork,

bytheirprimaryaddress.

TostartM-BUSmodulessearching,pressStart Discoverkey.

M-BUS Master 25

English

Aftersearchingbyprimaryaddress,M-BUSMASTERwillstarttosearchbysecondaryaddress.

Pict.4–Searchingdevicesinprogress

26 M-BUS Master

English

WhenM-BUSMASTERfindsadevice,itwillbeaddedintheList discovered devices(Pict.5).

Pict.5–Onedevicehasbeenfoundedbyautomaticresearch

TostoptheM-BUSmodulesearching,pressStop Discoverkey.

SelectthedevicetobeaddedandthenpressAdd devicekey.

Apopupwindowwillappear(Pict.6).Inthiswindowtheenergycounternicknameandtype(Singlephaseor

Threephase)shouldbechoosen.

Pict.6–Adddevice

Selectcountertype,enterthenicknameandthenpressSetkey.Theenergycounternamewillbedisplayed

intheleftcolumnunderthefolderEnergy counters.

M-BUS Master 27

English

2.2 Add an energy counter by manual procedure

ThefollowingdescriptionshowshowtoaddanewenergycountercombinedtoanM-BUSmodulebymanual

procedure.

ClickonAdd counter manuallyitemintheleftcolumn.Thefollowingparametersareshown(Pict.7).

ToaddanM-BUScommunicationmodulemanually,followtheinstructionsbelow:

1.Selecttheenergycountertype(SinglephaseorThreephase)

2.EntertheNickname,thePrimaryAddress,theIdentificationNumberandtheFirmwareVersionofthe

device.

3.ConfirmthechoicesbyclickingonAdd Devicekey.

Afterthat,theenergycounternamewillbedisplayedintheleftcolumnunderthefolderEnergy counters.

Pict.7–Addenergycountermanually

28 M-BUS Master

English

TheSecondaryAddressismadeasdescribedbelow.

Ifthereisnochanges,theSecondaryAddressisshownonthelabeloftheM-BUScommunicationmodule.

Byte Nr. Value (Hex) Description

1–4 xxxxxxxx M-BUSInterfaceIdentificationNumber

5–6 xxxx Manufacturer’sID

7 xx VersionNumberofM-BUSInterfaceFirmware(00–FF)

8 02 Medium:Electricity

ForexampleinPict.7theSecondaryAddressis:

00000000 M-BUS Interface Identification Number

182E Manufacturer ID

02 Firmware Version

02 Medium Number (Electricity)

M-BUS Master 29

English

2.3 Energy counter management

Fourpageswithrelevanttab(Device information,Device setup,Device commands,Device data)areavailable

forenergycountermanagement.

2.3.1. DEVICE INFORMATION

Intheleftcolumn,selectthedesideredenergycounterandthenclickonDevice informationtab.

Thefollowingpagewillbedisplayedshowingtheinformationdetailsontheconnecteddevice.

Pict.8–Deviceinformation

30 M-BUS Master

English

2.3.2. DEVICE SETUP

Intheleftcolumn,selectthedesideredenergycounter(orcheckifthedeviceselectionhasalreadybeen

made)andthenclickonDevice setuptab.

Thefollowingpagewillbedisplayedshowingthepossibilitytoselectthetimeintervalformeasurementsrefresh.

Availablesettings:

•Continue:refreshiscontinuously.

•10 sec.:refreshismadeevery10seconds.

•30 sec.:refreshismadeevery30seconds.

•One shot:refreshismadeonce.

•Stop:refreshisstopped.

Pict.9–Devicesetup

M-BUS Master 31

English

2.3.3. DEVICE COMMANDS

Intheleftcolumn,selectthedesideredenergycounter(orcheckifthedeviceselectionhasalreadybeen

made)andthenclickonDevice commandstab.

ThefollowingpagewillbedisplayedshowingthepossibilitytosendsomecommandstotheM-BUSmodule

andtotheenergycounter.

Availablecommands:

•Setdeviceprimaryaddress

•Setdevicesecondaryaddress

•Setdevicebaudrate

•Resetenergycounter

•Resetpartialenergycounter

•Startpartialenergycounter

•Stoppartialenergycounter

•Setdevicepublisheddata

EachcommandcanbesentbyprimaryorsecondaryaddressoftheM-BUSmodule,accordingtotheselection

(Command addressing mode).

Pict.10–Devicecommands

ATTENTION: M-BUS Master will show a positive message if the command is sent with success; this means

that the command has been received correctly by the M-BUS communication module, but it is not possible

to detect if the command has been received by the energy counter too.

ATTENTION: After sending a command to change the baud rate of the MBUS communication module, it is

necessary to go to “Application Setup” page and change the baud rate of the serial port in use. If this action

is not performed within 5 minutes (and the M-BUS module doesn’t receive any command for 5 minutes),

the M-BUS communication module turns back to the old baud rate.

32 M-BUS Master

English

IfSet device published dataisselected,thefollowingpagewillbedisplayed:

Pict.11–Devicecommands:setdevicepublisheddata

InthispageitispossibletoselectthemeasurementstobeshownonDevice datapage.

M-BUS Master 33

English

2.3.4. DEVICE DATA

Intheleftcolumn,selectthedesideredenergycounter(orcheckifthedeviceselectionhasalreadybeen

made)andthenclickonDevice datatab.

ThefollowingpagewillbedisplayedshowingthemeasurementsselectedbyDevice commandspage.

ThemeasurementsrefreshchangesaccordingtothetimeintervalselectedinDevice setuppage.

Pict.12–Devicedata

ATTENTION: Data displayed in red is old data and it means that there is no communication between the

M-BUS module and the energy counter: a red LED and “Disconnected” will be shown on the status bar.

34 M-BUS Master

English

2.4 Remove an energy counter

Itispossibletodisconnectanenergycounterbyremovingit.

Theenergycounterremovalcanbecarriedoutbyselectingtheenergycountertoberemoved,rightclickonit

andthenpresstheDeletebuttonjustshown(Pict.13).

Pict.13–Removinganenergycounter

Page is loading ...

Edited in Germany • Subject to change without notice • A pdf version is available on the Internet

GMC-I Messtechnik GmbH

Südwestpark 15

90449 Nürnberg •

Germany

Phone +49 911 8602-111

Telefax +49 911 8602-777

E-Mail [email protected]

www.gossenmetrawatt.com

Gossen MetraWatt U180B Operating instructions

Gossen MetraWatt U180B Operating instructions

in other languages

Related papers

Other documents