• Set the steam regulator to the appropriate setting:
- Set the steam regulator to the “1” position for “••” temperature setting
- Set the steam regulator to the “2” position for “•••” and “max” temperature
settings
Ironing without steam
•Set the steam regulator to the “0” ( ) position
• Select an appropriate temperature for the type of material being ironed
Spray
• Make sure that there is water in the tank
• Press the spray “
” button
Vertical steaming with jet of steam
• Never spray or aim steam at people !
• Set the temperature control to the “•••” or “max” position
• Hold the iron in an upright position 10-20 cm away from the object being
steamed
• Press the jet of steam “
” button at intervals of 5 seconds
Ironing with jet of steam
• Set the temperature control to the “•••” or “max” position
• Press the jet of steam “ ” button repeatedly at intervals of 5 seconds
Additional features: (dependent on model)
Anti-drip system
If your iron is equipped with an anti-drip system, it will automatically stop
producing steam when the selected temperature setting is too low. You may
hear a clicking sound when this system is in operation
Anti-scale system
If your iron is equipped with an anti-scale system, this will reduce the build up of
lime scale, consequently prolonging the life of the appliance. However, this
system does not completely prevent the formation of lime scale. Please read the
“After finishing each ironing session” section of the instructions for use. If you
live in a hard water area, please also read the “Filling the water tank” section of
the instructions for use
After finishing
each ironing session
• Unplug the iron from the mains socket
• Set the steam regulator to the “0” ( ) position
• Empty out the water tank – hold the iron with the point facing down and shake
it gently
• Coil the cable around the heel of the iron but not too tightly
• Leave the iron standing in the vertical position to cool down before storing
Self-cleaning
After finishing each ironing session turn the steam regulator knob back and forth
between the “0” (
) position and the “2” position several times to remove any
traces of lime scale that are left on the valve needle
Problem Possible causes Solution
Iron does not Temperature control set to Turn the temperature
work or is minimum selector to the desired
not heating up position
Connection problems Check that the plug is inserted into
the mains socket correctly
Iron is not There is no water in the tank Fill the water tank
steaming
The steam regulator is in the Set the steam regulator
“0” ( ) position to the corresponding position
Water is The temperature control is set Set the temperature control
dripping from too low for the iron to produce within the steam “
” area,
the holes in the steam and the iron does not have between “••” and “max” or turn
soleplate an anti-drip system the steam regulator to “0” ( )
You have pressed the jet of steam Wait 5 seconds between each
button repeatedly without waiting press of the jet of steam button
5 seconds between each press
Water has been left in the tank Always empty the tank after
when the soleplate was cold, ironing and set the steam
with the steam regulator in the on regulator to “0” ( ) after ironing
position and when filling the tank
Distilled water has not been Mix distilled water with tap water
used (see section on filling the as directed in the table under
water tank) or other products such “filling the water tank” and never
as fragrant water have been add any other products to the
added to the tank water tank
Deposits come Traces of lime scale from the Carry out a cleaning cycle
out through the steam chamber - see “Self cleaning” section
holes in the of the instructions for use
soleplate
SOLVING MINOR PROBLEMS YOURSELF Cleaning and maintenance
!
Attention ! Risk of burns !
• Clean the body of the iron and the soleplate with a damp cloth and then
dry it
• In the event that the soleplate is heavily stained: when the soleplate is
cold, iron a linen cloth soaked in white vinegar or stand the soleplate in a
container with vinegar for 15 minutes (maximum depth 1mm). Then
dampen a cloth with water and wipe the soleplate clean, then dry it
thoroughly.
Or:
• To immediately remove any marks on the soleplate use a dry cotton cloth
folded several times with the iron set to the maximum temperature setting
• Do not de-scale or clean the water tank with cleaning products or
solvents, as these could cause the iron to drip when using the steam
function
• Do not use a “professional steam cleaner” for cleaning the appliance
Advice on discarding used appliances
Before throwing a used appliance away, you should make it noticeably
inoperable and be certain to dispose of it in accordance with current laws
and regulations. Your retailer, town council or local council can give you
detailed information about these.
GUARANTEE TERMS
The terms of the guarantee for this appliance are in accordance with that
stated by our representative for the country in which it is sold. Details of
those conditions can be obtained from the retailer from whom the appliance
was purchased. The SALES RECEIPT must be presented when making any
claims against the terms of this guarantee
We reserve the right to make technical modifications
02
1
02
1