Star Trac E Series Embedded Installation guide

1

N4i Installation Manual

(picture of N4i screen)

2

Table of Contents

N4i Computer Parts List.................................................................................................. 4

Netpulse Stabilizer Bar Parts List................................................................................... 6

Hardware List................................................................................................................... 7

Tools Needed for Installation........................................................................................... 7

N4i Assembly Instructions ............................................................................................... 8

Wiring the N4i Station.................................................................................................... 10

N4i Final Assembly......................................................................................................... 12

Install Stabilizer Bar....................................................................................................... 20

PC Configuration Instructions...................................................................................... 24

Quick Test Procedures:.................................................................................................. 27

3

N4i Stand Parts List

Lower Floor Stand Vertical Tube Upper Floor Stand Vertical Tube

Floor Stand Base Weldment Floor Stand Base Feet (2)

Base End Cap (2) Power Supply Bracket

4

Floor Stand Base Cover Base Cable Chase Extrusion (2) & Base

Cable Chase Cover (2)

N4i Computer Parts List

N4i Computer Computer Rear Shield

Computer Power Cable Computer Power Extender Cable

5

TV Coax Cable Cat5 Cable (wired installs only)

Wireless Adapter and USB Cable Computer Rear Bracket

(wireless installs only)

Computer Mount Adapter Plate and Tilt Box

6

Netpulse Stabilizer Bar Parts List

Stabilizer Bars (1 long, 1 short) Stabilizer Bracket

Velcro Straps (2) Rubber Sleeves

7

Hardware List

NETPULSE STAND ASSEMBLY

4 1/4-20 x 7/8" Socket Head Screw

Feet to Floor Stand Base Cover

4 1/4-20 x 5/8" Socket Head Screw

Base End Cap / Base Cable Chase Extrusion

2 1/4-20 x 1 1/8 Socket Head Screw

Floor Stand Base Cover front to Floor Stand Base

Weldment

2 1/4-20 x 1 3/8 Socket Head Screw

Floor Stand Base Cover rear to Floor Stand Base

Weldment

2 8-32 x 7/16 Phillip Head Self Tapping Screw

Floor Stand Base Cover to Floor Stand Base

Weldment

3 5mm x 8mm Socket Set Screw

Lower Floor Stand Vertical Tube

2 1/4-20 x 1/2 Pan Head Machine Screw

Lower Floor Stand Vertical Tube to Base Weldment

2 1/4-20 x 1/2 Pan Head Machine Screw

Lower Floor Stand Vertical Tube to Upper Floor Stand

Vertical Tube

2 1/4-20 x 1/4 Pan Head Machine Screw

Computer Mount Adapter Plate and Tilt Box to Upper

Floor Stand Vertical Tube

Netpulse N4i Computer Assembly

4 8/32 x 5/8 Phillips Head Screw

N4i Computer to Computer Rear Bracket and

Computer Mount Adapter Plate and Tilt box

2 5/32 x 1 3/8 Phillips Head Screw

Computer Rear Shield to Computer Rear Bracket

4 1/4-20 x 1/2 Socket Head Screw

Computer Mount Adapter Plate and Tilt box

Netpulse Stabilizer Bar Assembly

4 1/4-20 x 1 3/8 Socket Head Screw

Stabilizer bar

4 1/4" Flat Washer

Stabilizer bar

4 1/4-20 Hex Nut

Stabilizer bar

1 1/4-20 x 1/4 Pan Head Machine Screw

Stabilizer Bracket to Lower Floor Stand Vertical Tube

Tools Needed for Installation

PC Keyboard (PS/2)

Hand Tools:

- Allen Wrench (7/32 and 3/32 drive)

- Phillips head screwdriver

- Crescent wrench or 7/16” open end wrench

8

N4i Assembly Instructions

Follow these steps to assemble N4i Station:

1). Determine the width of the two Floor Stand Base Feet relative to the cardio equipment

base, as shown. Attach the two Floor Stand Base Feet to Floor Stand Base Weldment

using four Socket Head Screws (1/4-20 x 7/8).

9

2). Attach the Base Cable Chase Extrusion to both sides of the Floor Stand Base

Weldment and secure with two Socket Head Screws (1/4-20 x 5/8), as shown.

3). Slide the Power Supply Bracket over the base weldment tube of the Floor Stand Base

Weldment, as shown.

4). Slide the Lower Floor Stand Vertical Tube onto the Floor Stand Base Weldment tube

and align the cables access holes, as shown. Insert and hand-tighten two Pan Head

Machine screws (1/4-20 x ½), but do not tighten at this time.

10

5). Place stand in front of cardio equipment and insert the Upper Floor Stand Vertical

Tube into the Lower Floor Stand Vertical Tube.

Wiring the N4i Station

1). Connect the Computer Power Cable to Computer Power Extender Cable, as shown.

Feed Computer Power extender Cable down the top of the Upper Floor Stand Vertical

11

Tube until it emerges from the cable access hole at the bottom of the Lower Floor Stand

Vertical Tube, as shown.

2). In the same way, feed TV Coax Cable and Cat5 Cable (for wired stations only) down

Upper Floor Stand Vertical Tube. Leave 8-10 inches of all three cables (coax, cat5, and

power) exposed at the top of Upper Floor Stand Vertical Tube.

3). Feed upper ends of cables through Computer Rear Shield as shown in picture above.

Slide the Computer Rear Shield all the way down the Floor Stand Vertical Tube for now

to keep it out of the way until you are to attach in a later step.

12

4). Attach Computer Power Cable to Computer Power Extender Cable, as shown.

N4i Final Assembly

1). Assemble Computer Mount Adapter Plate to Tilt box using the four Socket Head

Screws (1/4-20 x ½). Completed assembly is shown above.

13

2). Attach Computer Rear Bracket to back of N4i Computer as shown above. Attach

computer mount/tilt box assembly you assembled in step 1 to the Computer Rear Bracket

and secure with four Phillips head screws (8/32 x 5/8).

3). Slide computer mount/tilt box assembly onto Upper Floor Stand Vertical Tube and

route cables (power, coax, catt5) out the bottom as shown in picture above. Secure with

two Pan Head Machine screws (1/4-20 x ¼).

14

4). Connect the TV Coax Cable, Cat5 Cable, (for wired stations only), and Computer

Power Cable to the connections on the back of N4i Computer.

5). Adjust the height of the N4i screen by sliding the Upper Floor Stand Vertical Tube up

or down to the desired location and securing with two Pan Head Machine screws (1/4-20

x ½).

15

6). Adjust screen to appropriate viewing angle by first loosening the Socket Head Screws

on the computer mount/tilt box assembly and then tightening in place.

7). For wired installs, skip to step 13. For wireless installs attach a piece of Velcro on the

inside of Computer Rear Shield, as shown.

16

8). Attach another piece of Velcro to Wireless Adapter.

9). Feed USB Cable through bottom hole of computer mount bracket/tilt box assembly

and plug USB cable into either USB port on back of N4i Computer. (It doesn’t matter

which USB port you use).

10). Attach wireless adapter to inside of Computer Rear Shield (using Velcro attached

earlier). Place antenna through hole as shown in picture above. Slide Computer Rear

Shield up the Floor Stand Vertical Tube and plug the free end of the USB Cable into the

Wireless Adapter.

17

12). Coil up any access USB Cable inside the Computer rear Shield and then secure

Computer Rear Shield to Computer Rear Bracket using two Phillips head screws (5/32 x

1 3/8). Skip to step 15.

13). For wired installs, slide Computer Rear Shield up the Floor Stand Vertical Tube and

secure to Computer Rear Bracket using two Phillips head screws (5/32 x 1 3/8).

18

14). Insert four Socket Set Screws (5mm x 8mm) into Lower Vertical Tube (3) and

computer mount/tilt box assembly (1) then tighten.

15). Place power supply at base of Floor Stand Base Cover as shown above. Wrap excess

cable around bottom of Floor Stand Base Weldment tube so power supply and cables can

be cover by Floor Stand Base Cover.

16). Feed cables through Base Cable Chase Extrusion (feed through the side closest to

cable sources).

17). Connect cables (coax, power, cat5 if wired install) to their respective sources.

19

18). Place the Base End Cap on the Floor Stand Base Cover as shown above (this end

will not have cables fed through). Secure with two Socket Head Screws (1/4-20 x 5/8).

19). Install Base Cable Chase Cover into slot on top of Base Cable Chase Extrusion.

Repeat for each side.

20

20). Attach Floor Stand Base Cover and secure with four Socket Head Screws (1/4-20 x 1

1/8 and 1/4-20 x 1 3/8) and Phillips Head Self Tapping Screws (8-32 x 7/16).

Install Stabilizer Bar

1). Determine correct length of the stabilizer required between the Floor Stand Vertical

Tube and the cardio equipment. Slide the long Stabilizer Bar inside the short Stabilizer

Bar to the desired length and insert two socket head screws (1/4-20 x 1 3/8). Secure

screws with flat washers (¼”) and hex nuts (1/4-20).

Page is loading ...

Related papers

Other documents