Ohlins KA802 Mounting Instruction

Ohlins
Brand
Ohlins
Model
KA802
Type
Mounting Instruction

Ohlins KA802 is a rear monoshock absorber designed for the Kawasaki ZX-7R motorcycle. It features adjustable rebound and compression damping, as well as hydraulic preload adjustment, allowing you to fine-tune the suspension to suit your riding style and the riding conditions. The shock is designed to improve handling and stability, especially during acceleration, braking, and cornering. It can also help to reduce rider fatigue and improve overall comfort on long rides. The KA802 is relatively easy to install, and all necessary hardware is included. It also comes with a detailed instruction manual to guide you through the process.

Ohlins KA802 is a rear monoshock absorber designed for the Kawasaki ZX-7R motorcycle. It features adjustable rebound and compression damping, as well as hydraulic preload adjustment, allowing you to fine-tune the suspension to suit your riding style and the riding conditions. The shock is designed to improve handling and stability, especially during acceleration, braking, and cornering. It can also help to reduce rider fatigue and improve overall comfort on long rides. The KA802 is relatively easy to install, and all necessary hardware is included. It also comes with a detailed instruction manual to guide you through the process.

MOUNTING INSTRUCTION
Brand
KAWASAKI
Model
ZX-7R
Year
1998
Art. No.
KA 802
Total length
350
+12
0 mm
Stroke
75
mm
Reb.click
12
Comp.click
10
Preload
13
mm
Date
98-03-20
Supplementary parts
192-01
1180-01
231-01
1046-25
Sticker /Dekal (2x)
Memo sticker/ Memo dekal
Owners manual / Bruksanvisning
Tie rap / Buntband (2x)
Bolt / Screw M8x50
Mounting instructions
1.
Palla upp MC:n så att bakhjulet hänger fritt i
luften. Lossa sadeln. Tag ur batteriet och botten
av batterilådan.
2.
Lossa först den nedre fästbulten till
stötdämparen, därefter den övre.
3.
Lossa skruven till draglänkarna.
4.
Tag ut dämparen uppåt.
5.
Sätt Öhlinsdämparen på plats i omvänd ordning.
6.
Montera övre och nedre fästskruven. Montera
tillbaka draglänkarna.
7.
Hydraulförspännaren monteras på höger sida i
ljuddämparfästet.Använd medföljande skruv
1046-25. Bind upp slangen med buntband 231-
01.
8.
Montera tillbaks batteri och sadel.
9.
Kontrollera att alla skruvar är åtdragna innan du
ger dig ut på en provtur.
1.
Put the motorcycle on a stand so that the rear
wheel is off the ground. Remove the seat and the
battery and the bottom of the battery box.
2.
Remove the lower and upper shock mounting
bolts.
3.
Remove the bolt, which connects the pull rods
and triangular link.
4.
Remove the shock upwards.
5.
Put the Öhlins shock in place in reverse order.
6.
Mount the upper and lower mounting bolts.
Mount the linkage bolt to the pull rods.
7.
The hydraulic preload adjuster shall be mounted
in the silencer bracket on the right side of the
bike. Use the supplied bolt 1046-25. Tie up the
hose with the tie raps 231-01.
8.
Reinstall the battery and the seat.
9.
Check that all bolts are tightened before you go
for a test ride.
Groove / Spår
Lock nut /Låsmutter
På denna modell finns en ändögla/bygel monterad
som är justerbar på längden.
Öglan/bygeln får ej skruvas ut längre än att spåret
blir helt synligt under låsmuttern. Se skiss. Se till
att låsmuttern är fastdragen efter justering.
This model has an adjustable end eye/bracket
mounted. The end eye/bracket must not be threaded
out more than that the groove is visible beneath the
lock nut. See fig. Make shure that the lock nut is
tightened after adjustment
Öhlins Racing AB frånsäger sig allt ansvar för
skada på stötdämpare, motorcykel eller person om
inte monterings- och skötsel instruktionerna har
följts till fullo. Ingen garanti kan ges på funktion
eller livslängd om dessa instruktioner inte följts
Öhlins Racing AB can not be responsible for any
damage to shock absorber, motorcycle or person if
the mounting- and maintaining instructions are not
followed exactly. Also no guarantee can be given
for the performance and reliability if these
instructions are not followed.
  • Page 1 1

Ohlins KA802 Mounting Instruction

Ohlins
Brand
Ohlins
Model
KA802
Type
Mounting Instruction

Ohlins KA802 is a rear monoshock absorber designed for the Kawasaki ZX-7R motorcycle. It features adjustable rebound and compression damping, as well as hydraulic preload adjustment, allowing you to fine-tune the suspension to suit your riding style and the riding conditions. The shock is designed to improve handling and stability, especially during acceleration, braking, and cornering. It can also help to reduce rider fatigue and improve overall comfort on long rides. The KA802 is relatively easy to install, and all necessary hardware is included. It also comes with a detailed instruction manual to guide you through the process.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers