Roberts OrtusTime User guide

Brand: Roberts

Model: OrtusTime

Category: Alarm clocks

Type: User guide

This manual is also suitable for

OrtusTime( Rev.1)

Roberts OrtusTime is a DAB+/FM RDS digital alarm clock radio that boasts a variety of features to enhance your listening experience. With its crystal-clear digital audio, you can enjoy your favorite radio stations in exceptional quality. Utilize the DAB+ technology to access a wide range of digital radio stations, or tune into your preferred FM broadcasts.

Please read this manual before use

DAB / DAB+ / FM RDS digital alarm clock radio

Ortus Time

Controls ...............................................................................2

8VLQJWKHFORFNUDGLRIRUWKH¿UVWWLPH .................................3

Operating your clock radio - DAB ........................................4

Using the buttons.................................................................4

Selecting a station - DAB.....................................................5

Secondary services - DAB...................................................5

Finding new stations - DAB .................................................5

Manual tuning - DAB ...........................................................6

'\QDPLFUDQJHFRQWURO'$% ..............................................6

Prune stations - DAB ...........................................................7

Operating your radio - FM ...................................................7

Manual tuning - FM..............................................................8

Scan sensitivity setting - FM ................................................8

Display options - DAB / FM .................................................9

Presetting stations .............................................................10

6HWWLQJDODUPWLPHV .......................................................11-12

&DQFHOOLQJDODUPV ..............................................................13

Snooze function .................................................................13

7RYLHZWKHDODUPVHWWLQJV .................................................13

Contents

Sleep function ....................................................................14

$XWRPDWLFDOO\XSGDWLQJWKHFORFN .......................................14

6HWWLQJWKHFORFNIRUPDW .....................................................15

6HWWLQJWKHFORFNPDQXDOO\ .................................................15

Software version ................................................................16

'LVSOD\EDFNOLJKWGLPPHU...................................................16

Language function .............................................................17

Equaliser function ........................................................ 17-18

86%VRFNHWIRUVPDUWSKRQHRUWDEOHWFKDUJLQJ ..................18

Headphone socket.............................................................19

Auxiliary input socket .........................................................19

6\VWHPUHVHW......................................................................20

(OHFWURPDJQHWLFFRPSDWLELOLW\DGYLFH ...............................20

3URGXFWPDUNLQJV...............................................................20

Safety notices ....................................................................21

6SHFL¿FDWLRQV ....................................................................22

Circuit features ..................................................................22

Guarantee.............................................................Back page

Controls

1. Alarm 1 / Volume Down button

2. On/Off / Sleep button

3. Preset / Dimmer button

4. Alarm 2 / Volume Up button

5. Tuning / Select / Info control

6. LCD display

7. Snooze / Menu / Mode button

8. Volume control

(Top)

9. Auxiliary input socket

10. Headphone socket

11. DAB / FM wire antenna

12. DC input socket

13. USB charging socket

14. Loudspeaker

15. Micro USB socket

(underneath the unit for service use only)

Sleep

Mode

Ant

(Rear)

9 10 12 1311

8VLQJWKHFORFNUDGLRIRUWKH¿UVWWLPH

 3ODFH\RXUFORFNUDGLRRQDÀDWVXUIDFH

2. Carefully fully extend the wire aerial located on the rear of your clock

radio. Place the wire aerial so that it is as straight as possible extending

either above or below the clock radio.

3. Plug the mains adaptor into the DC input socket located on the rear of

your clock radio (marked 'DC') ensuring that the plug is pushed fully

into the socket.

4. Plug the other end of the mains adaptor into a standard mains socket

outlet and switch on the wall socket.

5. The display will show 'WELCOME' for a few seconds. During this time

WKHUDGLRLVVFDQQLQJWR¿QGD'$%UDGLRVLJQDO$IWHUDVKRUWWLPHWKH

current time and day will appear on the display and the clock hands

will be set to the correct time.

6. If no signal is found, '0:00' will be displayed. It may be necessary to

relocate your clock radio to a position giving better reception. You

VKRXOGWKHQFDUU\RXWDVFDQWR¿QGVWDWLRQVDVGHVFULEHGRQSDJH

7KH$&DGDSWRUVKRXOGEHGLVFRQQHFWHGIURPWKHPDLQVVXSSO\DQGIURP

the clock radio when not in use.

IMPORTANT: The mains adaptor is used as the means of connecting the

product to the mains supply. The mains socket and any multi-way mains

block used for the product must remain accessible during normal use. In

order to disconnect the product from the mains, the mains adaptor should

be removed from the mains socket completely.

Use only the mains adaptor provided with the product, or a genuine

replacement provided by Roberts Radio. The use of alternative adaptors

will invalidate the guarantee.

Ant

Operating your clock radio - DAB

1. Press the On/Off button to switch on your clock radio.

 :KHQ¿UVWVZLWFKHGRQWKHFORFNUDGLRZLOOEHLQ'$%PRGH$IWHUHDFKXVH

the clock radio will remember the mode used and then switch on in that

mode the next time it is used. If the clock radio has been used before, the

last used station will be selected.

 ,I WKLVLV WKH ¿UVWWLPH WKHFORFNUDGLR KDVEHHQXVHG DVFDQRI WKH%DQG

III DAB channels will be carried out (depending on whether scanning was

already completed in standby mode). During the scanning process the display

will show the progress of the station search. The number on the right of the

display is the number of stations that have been found.

 :KHQ WKH VFDQ LV FRPSOHWHG WKH ¿UVW VWDWLRQ LQ QXPHULFDOSKD RUGHU

$=ZLOOEHVHOHFWHG7KH ¿UVW VWDWLRQLQWKHOLVW RIVWDWLRQVIRXQG

during scanning will be played. The display will show the station name.

5. If no signals are found then it may be necessary to relocate your clock radio

WRDSRVLWLRQJLYLQJEHWWHUUHFHSWLRQ<RXVKRXOGWKHQFDUU\RXWDVFDQWR¿QG

stations as described on page 5.

• Your clock radio has an indicator

on the display to indicate the strength

of the DAB radio signal being received.

Note:KHQ¿UVWVZLWFKHGRQWKHFORFNUDGLRZLOOVHWWKHYROXPHWRDPRGHUDWHO\

high level, in case the broadcast is very quiet. After you have set the volume,

the clock radio will remember the setting that you have applied for the next time

that it is used.

Sleep

Using the buttons

Most operations on the clock radio are performed by a simple short press of a button.

A few operations require a longer press of a button. In this case the instructions will tell you to apply a long press, and the button should be held

down for 2 or 3 seconds, until the clock radio has responded. An example of this is applying a long press to the Menu / Mode button to change the

operating mode of the clock radio.

Selecting a station - DAB

1. Press On/Off to switch on the clock radio.

2. Repeatedly, apply a long press on Menu/Mode until the 'DAB' mode is

selected.

3. Rotate Tuning to step through the list of available stations.

4. Press Tuning to select and tune to the desired station.

5. Adjust the Volume.

Note: If after selecting a station the display shows 'OFF AIR' it may be

necessary to relocate your clock radio to a position giving better reception.

Secondary services - DAB

Some radio stations may have one or more additional broadcasts associated with

them. If these are available, they will appear immediately after the main station

as you rotate the Tuning control clockwise. To tune to the selected service,

press Tuning.

Mode

Sleep

Finding new stations - DAB

As time passes new stations may become available or you may have moved your clock radio

to a different part of the country. In this case you may need to cause your clock radio to scan

for new stations.

1. Press On/Off to switch on the clock radio.

2. Repeatedly, apply a long press on Menu/Mode until the 'DAB' mode is selected.

3. Press Menu/Mode. 'SCAN' will show on the display.

4. Press Tuning. Your clock radio will perform a scan of the Band III DAB channels. As

new radio stations are found the station counter on the right-hand side of the display will

increase and the radio stations will be added to the list stored in the radio.

Manual tuning - DAB

Manual tuning allows you to tune your clock radio to a particular DAB

frequency in Band III. Any new stations found will be added to the station

list. This function can also be used to assist the positioning of the aerial or

WKHFORFNUDGLRWRRSWLPLVHUHFHSWLRQIRUDVSHFL¿FFKDQQHORUIUHTXHQF\

1. Repeatedly, apply a long press on Menu/Mode until the 'DAB' mode

is selected.

2. Press Menu/Mode.

3. Rotate Tuning until the display shows 'MANUAL'. Press Tuning.

4. Rotate Tuning to select the desired DAB channel. Press Tuning to

tune to the chosen frequency.

5. If a signal is present, this will be indicated on a signal strength display.

The minimum signal marker (

) shows the minimum signal strength

needed for good DAB reception.

6. When a DAB signal is found, as shown by the signal indicator chevrons,

any new radio stations found with this signal will be added to the list

stored in the clock radio. Press Menu/Mode to exit.

Dynamic Range Control (DRC) settings - DAB

The DRC facillity can make quieter sounds easier to hear when your clock

radio is used in a noisy environment. The default DRC setting is 0.

1. When in DAB mode, press Menu/Mode.

2. Rotate Tuning until 'DRC' is displayed. Press Tuning.

3. Rotate Tuning to select the required DRC setting.

DRC 0 - DRC is switched off, Broadcast DRC will be ignored. DRC

1/2 - DRC level is set to 1/2 that sent by broadcaster. DRC 1 - DRC is

set as sent by broadcaster.

4. Press Tuning WRFRQ¿UPWKHVHWWLQJNote: Not all DAB broadcasts use

the DRC function. If the broadcast does not provide DRC information,

then the DRC setting in the clock radio will have no effect.

Mode

Operating your radio - FM

1. Carefully extend the wire aerial. Press On/Off to switch on the clock radio.

2. Repeatedly, apply a long press on Menu/Mode until 'FM' mode is selected.

3. Rotate Tuning clockwise and then apply a long press on the Tuning

control. Your clock radio will scan in an upwards direction (low frequency to

KLJKIUHTXHQF\DQGVWRSDXWRPDWLFDOO\ZKHQLW¿QGVDVWDWLRQRIVXI¿FLHQW

strength.

4. After a few seconds the display will update. The display will show the

frequency of the signal found. If the signal is strong enough and there is

RDS data present then the clock radio will display the station name.

5. Rotate Tuning anti-clockwise and then apply a long press on the Tuning

control. Your clock radio will scan the FM band in a downwards direction

(high frequency to low frequency). When the waveband end is reached your

radio will recommence tuning from the opposite waveband end. Adjust the

Volume. To switch off your clock radio press On/Off.

Mode

Prune stations - DAB

If you move to a different part of the country, some of the stations which were

listed may no longer be available. Also, from time to time, some DAB services

may stop broadcasting, or may change location or frequency. Stations which

cannot be found, or which have not been received for a very long time are shown

in the station list with a question mark. The Prune stations function will delete the

marked DAB stations from your station list.

1. When in DAB mode, press Menu/Mode.

2. Rotate Tuning until 'PRUNE' is displayed. Press Tuning.

3. Rotate Tuning until 'Y' is displayed. Press Tuning to cause the invalid station

names to be removed from the station list.

4. If you do not wish to prune stations choose 'N' in step 3 above.

Note: If you have moved your clock radio to a different part of the country you

should also carry out a search for new stations (please see the section 'Finding

new stations' on page 5).

Sleep

Manual tuning - FM

1. Rotate Tuning to tune to a station.The frequency will change in steps

of 50kHz.

2. Adjust the Volume.

Scan sensitivity setting - FM

Your clock radio will normally scan for FM broadcasts which are strong

enough to give good reception. However, you may wish the Auto-scan

IXQFWLRQWRDOVREHDEOHWR¿QGZHDNHUVLJQDOVSRVVLEO\IURPPRUHGLVWDQW

radio transmitters. Your clock radio includes a local / distant option for the

Auto-scan function.

1. When in FM mode, press Menu/Mode.

2. The display will show 'SCAN'. Press Tuning.

3. Rotate Tuning to choose either the 'LOCAL' or 'DISTANT' option.

7KH'LVWDQWRSWLRQZLOODOORZWKHUDGLRWR¿QGZHDNHUVLJQDOVZKHQ

scanning.

4. Press Tuning WRFRQ¿UP7KH/RFDORU'LVWDQWVHWWLQJLVVWRUHGLQWKH

clock radio and remains in force until changed or until a System Reset.

Note: The initial setting (out of the box, or after a System Reset)

causes the radio to ignore weaker (or more distant) signals.

Mode

Display options - DAB / FM

Your clock radio has a range of display options when in DAB and FM modes:-

1. Press Tuning to cycle through the various options. All displays except

the text display will revert to the clock display after about 10 seconds.

DAB display options

Your clock radio can display the following in DAB mode:-

Station name, scrolling text, program type, multiplex name, frequency,

bit rate, signal strength, time and date.

For the signal strength, the minimum signal marker (

) shows the minimum

signal strength needed for good DAB reception. The signal indicator

chevrons increase or decrease showing the changing signal strength as

you adjust the wire aerial or your clock radio position.

FM display options

In FM mode your clock radio can use the Radio Data System (RDS) to

display the radio station name and additional text when provided by the

EURDGFDVWHUDQGZKHUHWKHUDGLRVLJQDOLVVXI¿FLHQWO\FOHDU

Your clock radio can display the following in FM mode:-

Station name, frequency, scrolling text, program type, time and date.

Scrolling text (DAB and FM)

Signal strength (DAB only)

Frequency (DAB and FM)

Time and day (DAB and FM)

Presetting stations

You may store your preferred DAB and FM radio stations to the preset station memories. There are 20 memory presets in your clock radio, 10 for DAB

and 10 for FM. Presets are remembered by your clock radio in the event of a power failure.

The procedure for setting presets and using them to tune stations is the same for FM and DAB modes, and is described below.

Storing a preset

1. Press On/Off to switch on the clock radio.

2. Select either the FM or DAB mode using the Menu/Mode button.

3. Tune to the required station as previously described.

4. Press and release the Preset button. The display will show, for example,

(PSW\ if no station has been stored to that preset.

5. Rotate Tuning to select the desired preset number under which you wish

to store the station.

6. Apply a long press on the Tuning control. The display will show,

'STORED'. The station will be stored under the chosen preset. Repeat

this procedure as needed for the remaining presets. Stations which are

already stored in the presets may be overwritten by following the above

procedure.

Recalling a preset

1. Press On/Off to switch on the clock radio.

2. Select either the FM or DAB mode using the Menu/Mode button.

3. Press and release the Preset button. The display will show, for example,

(PSW\ if no station has been stored to that preset. If a preset has

been stored, then the display will show either the station name (for DAB

stations) or the frequency (for FM stations).

4. Rotate Tuning to select the desired station. Press Tuning. Your clock

radio will then tune to the station stored in the selected preset memory.

Mode

1. If necessary, press On/Off to switch off your clock radio.

2. Apply a long press on Alarm 1 or Alarm 2 buttons.

3. 'ALARM 1' or 'ALARM 2' will show on the display and the alarm

LQGLFDWRUZLOOÀDVK3UHVVTuning to enter the alarm setting menu.

4. Rotate Tuning to select ON or OFF. If OFF is selected any current

setting for that alarm will be cancelled.

5. With 'ON' selected press Tuning to cause the alarm hour digits to

ÀDVKRQWKHGLVSOD\

6. Rotate Tuning to choose the desired alarm hour.

7. Press Tuning7KHDODUPPLQXWHGLJLWVZLOOÀDVKRQWKHGLVSOD\

8. Rotate Tuning to choose the desired alarm minute.

• If your clock radio has been set to use the 12 hour clock format there

will be an option here to set either AM or PM.

9. Press Tuning7KHDODUPGD\RSWLRQZLOOÀDVKRQWKHGLVSOD\

10. Rotate Tuning to choose the desired alarm day option:

Daily - Will sound everyday

Once - Will sound at one time only

Weekends - Will sound only on weekends

Weekdays - Will sound only on weekdays

• If setting the alarm to once only, continue with step 11 overleaf.

Otherwise skip to step 17.

Setting alarm times

Your clock radio has two alarms which can be set to wake you to DAB, FM radio or buzzer alarm. Each alarm can be set to sound once, daily, on

weekdays or at weekends. In the event of a power interruption your clock radio has a built in memory that will retain your alarm settings. Ensure that

the time is set correctly before setting the alarms. Note: The alarms can only be set when your clock radio is in standby mode.

Note: If no buttons are pressed for 10 seconds, your clock radio will exit the alarm setup.

Sleep

11. Press Tuning7KHDODUPGD\ZLOOÀDVKRQWKHGLVSOD\

12. Rotate Tuning to choose the alarm day.

13. Press Tuning7KHDODUPPRQWKZLOOÀDVKRQWKHGLVSOD\

14. Rotate Tuning to choose the alarm month.

15. Press Tuning7KHDODUP\HDUZLOOÀDVKRQWKHGLVSOD\

16. Rotate Tuning to choose the alarm year.

17. Press Tuning7KHDODUPVRXUFHRSWLRQZLOOÀDVKRQWKHGLVSOD\

18. Rotate Tuning to choose the desired alarm source (DAB, FM

or BUZZER).

19. Press Tuning to choose the alarm source.

20. If setting the alarms to the radio option, the radio alarm may be set to

the last listened radio station or any of the stations which have been

stored as presets.

Rotate Tuning to choose either 'LAST' to wake up to the last listened

radio station or from a preset on the display. Press Tuning to choose

the desired station option.

Note: You can only set the alarm to use a preset which has already

been stored. Please see 'Presetting stations' page 10.

21. The volume setting will show on the display. Rotate Tuning to choose

the desired alarm volume. The clock radio uses the saved volume

settings for each alarm when it sounds.

22. Press TuningWRFRQ¿UPWKHDODUPVHWWLQJV'SAVED' will show on

the display before exiting the alarm setup.

Radio alarms are indicated in the display by the

symbol and the

corresponding alarm number. Buzzer alarms are indicated by the

symbol and the corresponding alarm number.

Cancelling alarms

1. Whilst an alarm is sounding, press On/Off to cancel the alarm.

Snooze function

1. When the radio or buzzer alarm sounds, press Snooze. This will silence the

alarm for 5 minutes.

When Snooze has been pressed during an alarm, the display will show the

Snooze symbol

. This sequence can be repeated as needed.

2. To cancel the Snooze function, press On/Off.

To view the alarm settings

1. Press On/Off to switch off the clock radio if needed.

2. Apply a long press on Alarm 1 or Alarm 2 button to enter the alarm setup.

3. Repeatedly, press Tuning to cycle through each of the settings for the chosen

alarm.

You may use the Tuning control to modify any particular setting if desired,

XVLQJWKH7XQLQJFRQWUROWRHQWHUWKHPRGL¿FDWLRQ

Mode

Sleep

When the alarm sounds

7KHDODUPZLOOVRXQGDWWKHVHOHFWHGWLPHVIRUXSWRPLQXWHVXQOHVVFDQFHOOHG7KHYROXPHXVHGIRUWKHDODUPZLOOEHVSHFL¿HGGXULQJWKHDODUP

setting procedure. When your clock radio is set to wake by the radio alarm, your clock radio will switch to the selected radio station. If the radio cannot

FRQQHFWWRWKHVSHFL¿HG'$%UDGLRVWDWLRQWKHEX]]HUZLOOEHXVHGLQVWHDG

Note: If the radio is switched on because of a radio alarm you can control basic functions such as the volume control.

When the buzzer alarm activates it will start softly and gradually increase in level.

7KHDODUPLFRQZLOOÀDVKRQWKHVFUHHQDQGWKHFORFNUDGLRZLOODXWRPDWLFDOO\VZLWFKEDFNWRVWDQGE\PRGHZKHQWKHPLQXWHVKDYHHODSVHG

Sleep

Sleep function

Your clock radio can be set to turn off after a preset time has elapsed. The

sleep timer can be set to between 15 and 90 minutes. Ensure your clock

radio is switched on.

1. Apply a long press on the On/Off/Sleep button. The sleep symbol

ZLOOÀDVKRQWKHGLVSOD\

2. Rotate Tuning to select the desired sleep time. The sleep setting will

increase in increments from 15 up to 90 minutes. A further increment will

cause the sleep timer to be set to OFF which will cancel the sleep function.

3. Press Tuning. The display will exit the sleep options. Your clock radio will

switch off after the preset sleep time has elapsed.

4. To view the remaining sleep time, apply a long press on the On/Off/

Sleep button.

5. To cancel the sleep timer and switch off your clock radio before the chosen

sleep time has elapsed, press On/Off. To cancel the sleep timer without

switching off your clock radio, set the sleep timer to the OFF setting.

Sleep

Automatically updating the clock

Your clock radio will usually set the clock time using the DAB signal. Alternatively

you may set the clock manually.

1. Press On/Off to switch on the clock radio.

2. Press Menu/Mode.

3. Rotate and press Tuning to select 'SYSTEM', 'TIME', 'UPDATE' and then

choose an update option from, 'DAB' or 'NONE'.

4. Press Tuning WRFRQ¿UP\RXUFKRLFH

5. The clock radio will set its time according to the information received.

If a signal is not found you should then either position the clock radio or its aerial

so that a signal can be received, or revert to manual clock mode (see page 15).

Mode

Sleep

Setting the clock format

The clock display used in standby mode and when the clock radio is in use

can be set to 12 or 24 hour format. The clock format can only be set while

the unit is playing.

1. Press On/Off to switch on the clock radio.

2. To set the clock format, press Menu/Mode.

3. Rotate and press Tuning to select 'SYSTEM', 'TIME', '12/24 HR' and then

12 or 24 hour format.

4. Press TuningWRFRQ¿UP

If the 12 hour clock format is chosen, the clock radio will then use the 12 hour

clock for the setting of alarms, and will display a 12 hour clock with an AM or

PM indicator on the display.

Mode

Sleep

Setting the clock manually

Normally your clock radio will set its clock automatically using the DAB radio

signal. If no DAB signal is available and you need to set the time manually,

please follow the procedure shown below.

1. Press On/Off to switch on the clock radio.

2. Press Menu/Mode.

3. Rotate and press Tuning to select 'SYSTEM', 'TIME', 'SET TIME', hour,

minute, day, month and year setting.

4. Press Tuning WRFRQ¿UPWKHWLPHVHWWLQJ'SAVED' will show on the display

before exiting the clock setup.

• If your radio has been set to use the 12 hour clock format there will be an

option to set either AM or PM.

Mode

Sleep

Software version

The software version display cannot be altered and is just for your reference.

1. Press On/Off to switch on the clock radio.

2. Press Menu/Mode.

3. Rotate and press Tuning to select 'SYSTEM' and then 'SW VER'.

4. Press Tuning to display the software version.

5. Press Menu/Mode as needed to exit.

Mode

Sleep

Display backlight dimmer

The brightness of the display can be adjusted for when the clock radio

is in standby. If you use the unit in the bedroom, you may prefer a lower

standby brightness level than the standard setting. There are four standby

brightness levels.

To change the current standby brightness setting please follow these steps.

1. When the clock radio is in Standby, press the Dimmer button to choose

from the High, Medium, Low or almost Off dimmer setting.

When the radio is in standby pressing any button (except the dimmer button)

or the rotary controls will cause the radio to switch to the 'High' brightness

level for a few seconds. This is so that if the standby brightness level is

set to Low or almost Off, it is still possible to see the time when needed.

The display backlight will always use the high setting whenever the radio

is switched on.

Language function

<RXUFORFNUDGLRVPHQXVFDQEHFRQ¿JXUHGWRDGLIIHUHQWODQJXDJH

1. Press On/Off to switch on the clock radio.

2. Press Menu/Mode.

3. Rotate and press Tuning to select 'SYSTEM', 'LANGUAGE' and then

select your desired language.

4. Press Tuning. The display will change to the chosen language.

5. Press Menu/Mode as needed to exit.

Equaliser function

The sound on your clock radio can be adjusted to suit your personal taste

for the material that you are listening to. The clock radio has six preset

equaliser options. Alternatively, you may set the treble and bass levels to

your own preferences.

1. Press On/Off to switch on the clock radio.

2. Press Menu/Mode.

3. Rotate Tuning until 'SYSTEM' appears on the display. Press Tuning.

4. Rotate Tuning until 'EQ' appears on the display. Press Tuning.

5. Rotate Tuning to cycle through various options until the desired option

is displayed. The options are as follows: Normal, Classic, Jazz, Pop,

Rock, and Speech.

6. Press Tuning WRFRQ¿UP\RXUFKRLFH

Mode

Sleep

Mode

My EQ

You may set the treble and bass levels to your own preferences using the

'My EQ' menu.

1. Follow steps 1-4 on the previous page to enter the Equaliser setup menu.

2. Rotate Tuning until 'My EQ,,,' shows on the display.

3. Press Tuning. Rotate Tuning until Treble or Bass is displayed.

4. Press Tuning. The current Bass or Treble level will be shown on the

display.

5. To adjust the Treble or Bass setting rotate Tuning until the desired level

(-7 and +7) is displayed.

6. Press Tuning WRFRQ¿UP\RXUFKRLFH

To cancel the effect of the 'My EQ'SUR¿OHFKRRVHWKH1RUPDO option from

the equaliser menu. Note: The treble and bass settings will be remembered

for the next time you wish to use the 'My EQ' setting.

The loudness setting in the 'EQ' menu increases the bass and treble at

low volume settings.

USB socket for smartphone or tablet charging

Your clock radio has a USB socket which can be used for charging a smart-

phone, tablet or other similar devices.

Charge time may vary and in some cases may take longer to charge than when

using the manufacturers charging unit supplied with the device.

1. Ensure your clock radio is plugged in.

2. Connect your device to the USB charging socket at the rear of your clock

radio.

3. Your device will begin to charge.

4. Once your device has charged remove the USB lead.

Headphone socket

A 3.5mm Headphone Socket located on the rear of your clock radio is provided for

use with either headphones or an earpiece. Inserting a plug automatically mutes the

internal loudspeaker.

Please be aware that the sensitivity of headphones can vary widely. We therefore

recommend setting the volume to a low level before connecting headphones to the

clock radio.

IMPORTANT: Excessive sound pressure from earphones and headphones can cause

hearing loss.

To prevent possible hearing damage, do not listen at high volume levels

for long periods.

Auxiliary input socket

1. Connect a stereo or mono audio source (i.e. CD player, MP3

player, etc.) to the Auxiliary input socket.

2. Press On/Off to switch on the clock radio.

3. Repeatedly, apply a long press on the Menu/Mode button until

the display shows 'AUX IN'.

4. Adjust the Volume control on your player and on the clock radio

for comfortable listening.

5. Remove the cable from the Auxiliary input socket or apply a

long press on the Menu/Mode button to cancel Auxiliary Input

mode.

Note that audio played via the auxiliary input will be played in mono

through the speaker and in stereo through stereo headphones.

Mode

Sleep

Page is loading ...

Roberts OrtusTime User guide

Brand: Roberts

Model: OrtusTime

Category: Alarm clocks

Type: User guide

This manual is also suitable for

OrtusTime( Rev.1)

Download PDF

report

in other languages

français: Roberts OrtusTime Mode d'emploi

Roberts OrtusTime User guide

This manual is also suitable for

Roberts OrtusTime User guide

in other languages

Related papers

Other documents