Makita BDF343 User manual

Brand: Makita

Model: BDF343

Category: Power drills

Type: User manual

This manual is also suitable for

BDF453

GB Cordless Driver Drill Instruction manual

ID Bor Obeng Tanpa Kabel Petunjuk penggunaan

VI Máy khoan & vn vít chy pin Tài liu hng dn

 

BDF343

BDF453

1 012153 2 012128

3 009077 4 009078

5 009079 6 009080

7 009081 8 009082

ENGLISH

Explanation of general view

SPECIFICATIONS

•Due to our continuing programme of research and development, the specifications herein are subject to change without

notice.

•Specifications and battery cartridge may differ from country to country.

•Weight, with battery cartridge, according to EPTA-Procedure 01/2003

END004-4

Symbols

The following show the symbols used for the equipment.

Be sure that you understand their meaning before use.

..... Read instruction manual.

ENE034-1

Intended use

The tool is intended for drilling and screw driving in wood,

metal and plastic.

GEA006-2

General Power Tool Safety

Warnings

WARNING! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and

instructions for future reference.

The term “power tool” in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

1. Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

2. Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or fumes.

3. Keep children and bystanders away while

operating a power tool. Distractions can cause you

to lose control.

Electrical safety

4. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will

reduce risk of electric shock.

5. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

6. Do not expose power tools to rain or wet

conditions. Water entering a power tool will increase

the risk of electric shock.

7. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase

the risk of electric shock.

8. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of

electric shock.

9. If operating a power tool in a damp location is

unavoidable, use a ground fault circuit interrupter

(GFCI) protected supply. Use of an GFCI reduces

the risk of electric shock.

1. Red indicator

2. Button

3. Battery cartridge

4. Star marking

5. Switch trigger

6. Reversing switch lever

7. Speed change lever

8. Adjusting ring

9. Graduation

10. Pointer

11. Sleeve

Model BDF343 BDF453

Capacities

Steel 10 mm 13 mm

Wood 25 mm 36 mm

Wood screw 5.1 mm x 63 mm 6 mm x 75 mm

Machine screw 6 mm

No load speed (min

-1

)

High (2) 0 - 1,300

Low (1) 0 - 400

Overall length 192 mm 214 mm

Net weight 1.4 kg 1.6 kg

Rated voltage D.C. 14.4 V D.C. 18 V

Personal safety

10. Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools

may result in serious personal injury.

11. Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce

personal injuries.

12. Prevent unintentional starting. Ensure the switch

is in the off-position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your finger on the

switch or energising power tools that have the switch

on invites accidents.

13. Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result

in personal injury.

14. Do not overreach. Keep proper footing and

balance at all times. This enables better control of

the power tool in unexpected situations.

15. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing, and gloves

away from moving parts. Loose clothes, jewellery or

long hair can be caught in moving parts.

16. If devices are provided for the connection of dust

extraction and collection facilities, ensure these

are connected and properly used. Use of dust

collection can reduce dust-related hazards.

Power tool use and care

17. Do not force the power tool. Use the correct power

tool for your application. The correct power tool will

do the job better and safer at the rate for which it was

designed.

18. Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be

repaired.

19. Disconnect the plug from the power source and/or

the battery pack from the power tool before

making any adjustments, changing accessories,

or storing power tools. Such preventive safety

measures reduce the risk of starting the power tool

accidentally.

20. Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the

power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands

of untrained users.

21. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and

any other condition that may affect the power

tool’s operation. If damaged, have the power tool

repaired before use. Many accidents are caused by

poorly maintained power tools.

22. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

23. Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to

be performed. Use of the power tool for operations

different from those intended could result in a

hazardous situation.

Battery tool use and care

24. Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used

with another battery pack.

25. Use power tools only with specifically designated

battery packs. Use of any other battery packs may

create a risk of injury and fire.

26. When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys,

nails, screws or other small metal objects, that can

make a connection from one terminal to another.

Shorting the battery terminals together may cause

burns or a fire.

27. Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation or

burns.

Service

28. Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the power tool

is maintained.

29. Follow instruction for lubricating and changing

accessories.

30. Keep handles dry, clean and free from oil and

grease.

GEB088-1

CORDLESS DRIVER DRILL

SAFETY WARNINGS

1. Use auxiliary handle(s), if supplied with the tool.

Loss of control can cause personal injury.

2. Hold power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring. Cutting

accessory contacting a “live” wire may make exposed

metal parts of the power tool "live" and could give the

operator an electric shock.

3. Hold power tool by insulated gripping surfaces,

when performing an operation where the fastener

may contact hidden wiring. Fasteners contacting a

“live” wire may make exposed metal parts of the

power tool “live” and could give the operator an

electric shock.

4. Always be sure you have a firm footing.

Be sure no one is below when using the tool in

high locations.

5. Hold the tool firmly.

6. Keep hands away from rotating parts.

7. Do not leave the tool running. Operate the tool

only when hand-held.

8. Do not touch the drill bit or the workpiece

immediately after operation; they may be

extremely hot and could burn your skin.

9. Some material contains chemicals which may be

toxic. Take caution to prevent dust inhalation and

skin contact. Follow material supplier safety data.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product (gained

from repeated use) replace strict adherence to safety

rules for the subject product. MISUSE or failure to

follow the safety rules stated in this instruction

manual may cause serious personal injury.

ENC007-7

IMPORTANT SAFETY

INSTRUCTIONS

FOR BATTERY CARTRIDGE

1. Before using battery cartridge, read all

instructions and cautionary markings on (1)

battery charger, (2) battery, and (3) product using

battery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively shorter,

stop operating immediately. It may result in a risk

of overheating, possible burns and even an

explosion.

4. If electrolyte gets into your eyes, rinse them out

with clear water and seek medical attention right

away. It may result in loss of your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any

conductive material.

(2) Avoid storing battery cartridge in a container

with other metal objects such as nails, coins,

etc.

(3) Do not expose battery cartridge to water or

rain.

A battery short can cause a large current flow,

overheating, possible burns and even a

breakdown.

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50°C (122°F).

7. Do not incinerate the battery cartridge even if it is

severely damaged or is completely worn out. The

battery cartridge can explode in a fire.

8. Be careful not to drop or strike battery.

9. Do not use a damaged battery.

SAVE THESE INSTRUCTIONS.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely

discharged.

Always stop tool operation and charge the battery

cartridge when you notice less tool power.

2. Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room

temperature at 10°C - 40°C (50°F - 104°F). Let a hot

battery cartridge cool down before charging it.

4. Charge the battery cartridge once in every six

months if you do not use it for a long period of

time.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before adjusting or

checking function on the tool.

Installing or removing battery cartridge

(Fig. 1)

• Always switch off the tool before installing or removing

of the battery cartridge.

• To remove the battery cartridge, slide it from the tool

while sliding the button on the front of the cartridge.

•To install the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click. If you can see the red indicator

on the upper side of the button, it is not locked

completely. Install it fully until the red indicator cannot

be seen. If not, it may accidentally fall out of the tool,

causing injury to you or someone around you.

•Do not use force when installing the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

Battery protection system (Lithium-ion

battery with star marking) (Fig. 2)

For Model BDF453

Lithium-ion batteries with a star marking are equipped

with a protection system. This system automatically cuts

off power to the tool to extend battery life.

The tool will automatically stop during operation if the tool

and/or battery are placed under one of the following

conditions:

•Overloaded:

The tool is operated in a manner that causes it to

draw an abnormally high current.

In this situation, release the trigger switch on the tool

and stop the application that caused the tool to

become overloaded. Then pull the trigger switch

again to restart.

If the tool does not start, the battery is overheated. In

this situation, let the battery cool before pulling the

trigger switch again.

•Low battery voltage:

The remaining battery capacity is too low and the tool

will not operate. In this situation, remove and

recharge the battery.

Switch action (Fig. 3)

CAUTION:

•Before inserting the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the “OFF” position when

released.

To start the tool, simply pull the switch trigger. Tool speed

is increased by increasing pressure on the switch trigger.

Release the switch trigger to stop.

Reversing switch action (Fig. 4)

This tool has a reversing switch to change the direction of

rotation. Depress the reversing switch lever from the A

side for clockwise rotation or from the B side for

counterclockwise rotation.

When the reversing switch lever is in the neutral position,

the switch trigger cannot be pulled.

CAUTION:

•Always check the direction of rotation before operation.

•Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

• When not operating the tool, always set the reversing

switch lever to the neutral position.

Speed change (Fig. 5)

To change the speed, first switch off the tool and then

slide the speed change lever to the “2” side for high speed

or “1” side for low speed. Be sure that the speed change

lever is set to the correct position before operation. Use

the right speed for your job.

CAUTION:

•Always set the speed change lever fully to the correct

position. If you operate the tool with the speed change

lever positioned halfway between the “1” side and “2”

side, the tool may be damaged.

• Do not use the speed change lever while the tool is

running. The tool may be damaged.

Adjusting the fastening torque (Fig. 6)

The fastening torque can be adjusted in 17 steps by

turning the adjusting ring so that its graduations are

aligned with the pointer on the tool body. The fastening

torque is minimum when the number 1 is aligned with the

pointer, and maximum when the marking is aligned with

the pointer.

The clutch will slip at various torque levels when set at the

number 1 to 16. The clutch is designed not to slip at the

marking.

Before actual operation, drive a trial screw into your

material or a piece of duplicate material to determine

which torque level is required for a particular application.

ASSEMBLY

CAUTION:

•Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out any

work on the tool.

Installing or removing driver bit or drill bit

(Fig. 7)

Turn the sleeve counterclockwise to open the chuck jaws.

Place the bit in the chuck as far as it will go. Turn the

sleeve clockwise to tighten the chuck.

To remove the bit, turn the sleeve counterclockwise.

OPERATION

CAUTION:

•Always insert the battery cartridge all the way until it

locks in place. If you can see the red part on the upper

side of the button, it is not locked completely. Insert it

fully until the red part cannot be seen. If not, it may

accidentally fall out of the tool, causing injury to you or

someone around you.

Screwdriving operation (Fig. 8)

CAUTION:

• Adjust the adjusting ring to the proper torque level for

your work.

Place the point of the driver bit in the screw head and

apply pressure to the tool. Start the tool slowly and then

increase the speed gradually. Release the switch trigger

as soon as the clutch cuts in.

CAUTION:

• Make sure that the driver bit is inserted straight in the

screw head, or the screw and/or bit may be damaged.

NOTE:

•When driving wood screws, predrill pilot holes to make

driving easier and to prevent splitting of the workpiece.

See the chart.

006421

Drilling operation

First, turn the adjusting ring so that the pointer points to

the marking. Then proceed as follows.

Drilling in wood

When drilling in wood, the best results are obtained with

wood drills equipped with a guide screw. The guide screw

makes drilling easier by pulling the bit into the workpiece.

Drilling in metal

To prevent the bit from slipping when starting a hole, make

an indentation with a center-punch and hammer at the

point to be drilled. Place the point of the bit in the

indentation and start drilling.

Use a cutting lubricant when drilling metals. The

exceptions are iron and brass which should be drilled dry.

CAUTION:

•Pressing excessively on the tool will not speed up the

drilling. In fact, this excessive pressure will only serve

to damage the tip of your bit, decrease the tool

performance and shorten the service life of the tool.

Nominal diameter of

wood screw (mm)

Recommended size of

pilot hole (mm)

3.1 2.0 - 2.2

3.5 2.2 - 2.5

3.8 2.5 - 2.8

4.5 2.9 - 3.2

4.8 3.1 - 3.4

5.1 3.3 - 3.6

5.5 3.7 - 3.9

5.8 4.0 - 4.2

6.1 4.2 - 4.4

• There is a tremendous force exerted on the tool/bit at

the time of hole break through. Hold the tool firmly and

exert care when the bit begins to break through the

workpiece.

•A stuck bit can be removed simply by setting the

reversing switch to reverse rotation in order to back

out. However, the tool may back out abruptly if you do

not hold it firmly.

•Always secure small workpieces in a vise or similar

hold-down device.

•If the tool is operated continuously until the battery

cartridge has discharged, allow the tool to rest for 15

minutes before proceeding with a fresh battery.

MAINTENANCE

CAUTION:

•Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance.

•Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

•These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

•Drill bits

•Screw bits

•Various type of Makita genuine batteries and chargers

•Automatic refreshing adapter

•Plastic carrying case

NOTE:

•Some items in the list may be included in the tool

package as standard accessories. They may differ from

country to country.

BAHASA INDONESIA

Penjelasan tampilan keseluruhan

SPESIFIKASI

•Karena kesinambungan program penelitian dan pengembangan kami, spesifikasi yang disebutkan di sini dapat

berubah tanpa pemberitahuan.

•Spesifikasi dan baterai dapat berbeda dari satu negara ke negara lainnya.

• Berat, dengan baterai, menurut Prosedur EPTA 01/2003

END004-4

Simbol

Berikut ini adalah simbol-simbol yang digunakan pada

peralatan ini. Pastikan Anda mengerti makna masing-

masing simbol sebelum menggunakan alat.

..... Baca petunjuk penggunaan.

ENE034-1

Penggunaan

Mesin ini digunakan untuk mengebor dan memasang

sekrup pada kayu, logam dan plastik.

GEA006-2

Peringatan Keselamatan Umum

Mesin Listrik

PERINGATAN! Bacalah semua peringatan

keselamatan dan semua petunjuk. Kelalaian mematuhi

peringatan dan petunjuk dapat menyebabkan sengatan

listrik, kebakaran dan/atau cedera serius.

Simpanlah semua peringatan dan

petunjuk untuk acuan di masa

depan.

Istilah “mesin listrik” dalam semua peringatan mengacu

pada mesin listrik yang dijalankan dengan sumber listrik

jala-jala (berkabel) atau baterai (tanpa kabel).

Keselamatan tempat kerja

1. Jaga tempat kerja selalu bersih dan

berpenerangan cukup. Tempat kerja yang

berantakan dan gelap mengundang kecelakaan.

2. Jangan gunakan mesin listrik dalam lingkungan

yang mudah meledak, misalnya jika ada cairan,

gas, atau debu yang mudah menyala. Mesin listrik

menimbulkan bunga api yang dapat menyalakan debu

atau uap tersebut.

3. Jauhkan anak-anak dan orang lain saat

menggunakan mesin listrik. Bila perhatian terpecah,

anda dapat kehilangan kendali.

Keamanan kelistrikan

4. Steker mesin listrik harus cocok dengan

stopkontak. Jangan sekali-kali mengubah steker

dengan cara apa pun. Jangan menggunakan

steker adaptor dengan mesin listrik berarde

(dibumikan). Steker yang tidak diubah dan

stopkontak yang cocok akan mengurangi risiko

sengatan listrik.

5. Hindari sentuhan tubuh dengan permukaan

berarde atau yang dibumikan seperti pipa,

radiator, kompor, dan kulkas. Risiko sengatan listrik

bertambah jika tubuh Anda terbumikan atau terarde.

6. Jangan membiarkan mesin listrik kehujanan atau

kebasahan. Air yang masuk ke dalam mesin listrik

akan meningkatkan risiko sengatan listrik.

7. Jangan menyalahgunakan kabel. Jangan sekali-

kali menggunakan kabel untuk membawa,

menarik, atau mencabut mesin listrik dari

stopkontak. Jauhkan kabel dari panas, minyak,

tepian tajam, atau bagian yang bergerak. Kabel

yang rusak atau kusut memperbesar risiko sengatan

listrik.

8. Bila menggunakan mesin listrik di luar ruangan,

gunakan kabel ekstensi yang sesuai untuk

penggunaan di luar ruangan. Penggunaan kabel

1. Indikator berwarna merah

2. Tombol

3. Baterai

4. Tanda bintang

5. Saklar pemicu

6. Tuas saklar pembalik arah

7. Tuas pengubah kecepatan

8. Cincin penyetel

9. Skala

10. Penunjuk

11. Selongsong

Model BDF343 BDF453

Kapasitas

Baja 10 mm 13 mm

Kayu 25 mm 36 mm

Sekrup kayu 5,1 mm x 63 mm 6 mm x 75 mm

Sekrup mesin 6 mm

Kecepatan tanpa beban (min

-1

)

Tinggi (2) 0 - 1.300

Rendah (1) 0 - 400

Panjang keseluruhan 192 mm 214 mm

Berat bersih 1,4 kg 1,6 kg

Teg an ga n teru kur D.C . 14,4 V D.C. 18 V

yang sesuai untuk penggunaan luar ruangan

mengurangi risiko sengatan listrik.

9. Jika mengoperasikan mesin listrik di lokasi

lembap tidak terhindarkan, gunakan pasokan daya

yang dilindungi pemutus rangkaian salah arde

(ground fault circuit interrupter - GFCI).

Penggunaan GFCI mengurangi risiko sengatan listrik.

Keselamatan diri

10. Jaga kewaspadaan, perhatikan pekerjaan Anda

dan gunakan akal sehat bila menggunakan mesin

listrik. Jangan menggunakan mesin listrik saat

Anda lelah atau di bawah pengaruh obat bius,

alkohol, atau obat. Sekejap saja lalai saat

menggunakan mesin listrik dapat menyebabkan

cedera diri yang serius.

11. Gunakan alat pelindung diri. Selalu gunakan

pelindung mata. Peralatan pelindung seperti masker

debu, sepatu pengaman anti-selip, helm pengaman,

atau pelindung telinga yang digunakan untuk kondisi

yang sesuai akan mengurangi risiko cedera diri.

12. Cegah penyalaan yang tidak disengaja. Pastikan

bahwa sakelar berada dalam posisi mati (off)

sebelum menghubungkan mesin ke sumber daya

dan/atau baterai, mengangkat atau membawanya.

Membawa mesin listrik dengan jari Anda pada

sakelarnya atau mengalirkan listrik pada mesin listrik

yang sakelarnya hidup (on) akan mengundang

kecelakaan.

13. Lepaskan kunci-kunci penyetel sebelum

menghidupkan mesin listrik. Kunci-kunci yang

masih terpasang pada bagian mesin listrik yang

berputar dapat menyebabkan cedera.

14. Jangan meraih terlalu jauh. Jagalah pijakan dan

keseimbangan sepanjang waktu. Hal ini

memungkinkan kendali yang lebih baik atas mesin

listrik dalam situasi yang tidak diharapkan.

15. Kenakan pakaian dengan baik. Jangan memakai

pakaian yang kedodoran atau perhiasan. Jaga

jarak antara rambut, pakaian, dan sarung tangan

Anda dengan bagian mesin yang bergerak.

Pakaian kedodoran, perhiasan, atau rambut panjang

dapat tersangkut pada bagian yang bergerak.

16. Jika tersedia fasilitas untuk menghisap dan

mengumpulkan debu, pastikan fasilitas tersebut

terhubung listrik dan digunakan dengan baik.

Penggunaan pembersih debu dapat mengurangi

bahaya yang terkait dengan debu.

Penggunaan dan pemeliharaan mesin listrik

17. Jangan memaksa mesin listrik. Gunakan mesin

listrik yang tepat untuk keperluan Anda. Mesin

listrik yang tepat akan menuntaskan pekerjaan

dengan lebih baik dan aman pada kecepatan sesuai

rancangannya.

18. Jangan gunakan mesin listrik jika sakelar tidak

dapat menyalakan dan mematikannya. Mesin listrik

yang tidak dapat dikendalikan dengan sakelarnya

adalah berbahaya dan harus diperbaiki.

19. Cabut steker dari sumber listrik dan/atau baterai

dari mesin listrik sebelum melakukan penyetelan,

penggantian aksesori, atau menyimpan mesin

listrik. Langkah keselamatan preventif tersebut

mengurangi risiko hidupnya mesin secara tak

sengaja.

20. Simpan mesin listrik jauh dari jangkauan anak-

anak dan jangan biarkan orang yang tidak paham

mengenai mesin listrik tersebut atau petunjuk ini

menggunakan mesin listrik. Mesin listrik sangat

berbahaya di tangan pengguna yang tak terlatih.

21. Rawatlah mesin listrik. Periksa apakah ada bagian

bergerak yang tidak lurus atau macet, bagian yang

pecah dan kondisi lain yang dapat mempengaruhi

penggunaan mesin listrik. Jika rusak, perbaiki

dahulu mesin listrik sebelum digunakan. Banyak

kecelakaan disebabkan oleh kurangnya pemeliharaan

mesin listrik.

22. Jaga agar mesin pemotong tetap tajam dan bersih.

Mesin pemotong yang terawat baik dengan mata

pemotong yang tajam tidak mudah macet dan lebih

mudah dikendalikan.

23. Gunakan mesin listrik, aksesori, dan mata mesin,

dll. sesuai dengan petunjuk ini, dengan

memperhitungkan kondisi kerja dan jenis

pekerjaan yang dilakukan. Penggunaan mesin listrik

untuk penggunaan yang lain dari peruntukan dapat

menimbulkan situasi berbahaya.

Penggunaan dan pemeliharaan mesin bertenaga

baterai

24. Isi ulang baterai hanya dengan pengisi daya yang

ditentukan oleh pabrikan. Pengisi daya yang cocok

untuk satu jenis baterai dapat menimbulkan risiko

kebakaran ketika digunakan untuk paket baterai yang

lain.

25. Gunakan mesin listrik hanya dengan baterai yang

telah ditentukan secara khusus. Penggunaan

baterai lain dapat menimbulkan risiko cedera dan

kebakaran.

26. Ketika baterai tidak digunakan, jauhkan dari

benda logam lain, seperti penjepit kertas, uang

logam, kunci, paku, sekrup atau benda logam kecil

lainnya, yang dapat menghubungkan satu

terminal ke terminal lain. Hubungan singkat terminal

baterai dapat menyebabkan luka bakar atau

kebakaran.

27. Pemakaian yang salah, dapat menyebabkan

keluarnya cairan dari baterai; hindari kontak. Jika

terjadi kontak secara tidak sengaja, bilas dengan

air. Jika cairan mengenai mata, cari bantuan

medis. Cairan yang keluar dari baterai bisa

menyebabkan iritasi atau luka bakar.

Servis

28. Berikan mesin listrik untuk diperbaiki hanya

kepada oleh teknisi yang berkualifikasi dengan

menggunakan hanya suku cadang pengganti yang

serupa. Hal ini akan menjamin terjaganya keamanan

mesin listrik.

29. Patuhi petunjuk pelumasan dan penggantian

aksesori.

30. Jagalah agar gagang kering, bersih, dan bebas

dari minyak dan gemuk.

GEB088-1

PERINGATAN KESELAMATAN

BOR OBENG TANPA KABEL

1. Gunakan gagang tambahan, jika disertakan

bersama mesin ini. Kehilangan kendali dapat

menyebabkan cedera.

2. Pegang mesin listrik pada permukaan genggam

yang terisolasi saat melakukan pekerjaan bila

aksesori pemotong mungkin bersentuhan dengan

kawat tersembunyi. Pengencang yang menyentuh

kawat “hidup” dapat menyebabkan bagian logam pada

mesin teraliri arus listrik dan menyengat pengguna.

3. Pegang mesin listrik pada permukaan genggam

yang terisolasi saat melakukan pekerjaan bila

pengencang mungkin bersentuhan dengan kawat

tersembunyi. Pengencang yang menyentuh kawat

“hidup” dapat menyebabkan bagian logam pada

mesin teraliri arus listrik dan menyengat pengguna.

4. Selalu pastikan Anda berada di atas alas yang

kuat.

Pastikan tidak ada orang di bawahnya bila Anda

menggunakan mesin di tempat yang tinggi.

5. Pegang mesin kuat-kuat.

6. Jauhkan tangan dari bagian yang berputar.

7. Jangan tinggalkan mesin dalam keadaan hidup.

Jalankan mesin hanya ketika digenggam tangan.

8. Jangan menyentuh mata bor atau benda kerja

segera setelah pengoperasian; suhunya mungkin

masih sangat panas dan dapat membakar kulit

Anda.

9. Bahan tertentu mengandung zat kimia yang

mungkin beracun. Hindari menghirup debu dan

persentuhan dengan kulit. Ikuti data keselamatan

bahan dari pemasok.

SIMPAN PETUNJUK INI.

PERINGATAN:

JANGAN biarkan kenyamanan atau terbiasanya Anda

dengan produk (karena penggunaan berulang)

menggantikan kepatuhan yang ketat terhadap aturan

keselamatan untuk produk yang terkait.

PENYALAHGUNAAN atau kelalaian mematuhi kaidah

keselamatan yang tertera dalam petunjuk ini dapat

menyebabkan cedera badan serius.

ENC007-7

PETUNJUK KESELAMATAN

PENTING

UNTUK BATERAI

1. Sebelum menggunakan baterai, bacalah semua

petunjuk dan penandaan pada (1) pengisi daya

baterai, (2) baterai, dan (3) produk yang

menggunakan baterai.

2. Jangan membongkar baterai.

3. Jika waktu beroperasinya menjadi sangat singkat,

segera hentikan penggunaan. Hal tersebut dapat

menimbulkan risiko panas berlebih, kemungkinan

mengalami luka bakar atau bahkan terjadi ledakan.

4. Jika elektrolit mengenai mata Anda, basuh dengan

air bersih dan segera cari pertolongan medis. Hal

tersebut dapat mengakibatkan hilangnya

kemampuan penglihatan Anda.

5. Jangan menghubungkan terminal baterai:

(1) Jangan menyentuhkan terminal dengan

bahan penghantar listrik apapun.

(2) Hindari menyimpan baterai pada wadah yang

berisi benda logam lain seperti paku, uang

logam, dsb.

(3) Jangan membiarkan baterai terkena air atau

kehujanan.

Hubungan singkat baterai dapat menyebabkan

aliran arus listrik yang besar, panas berlebih,

kemungkinan mengalami luka bakar dan bahkan

kerusakan pada baterai.

6. Jangan menyimpan mesin dan baterai pada lokasi

dengan suhu yang bisa mencapai atau melebihi

50°C.

7. Jangan membuang baterai di tempat pembakaran

sampah walaupun benar-benar rusak atau tidak

bisa digunakan sama sekali. Baterai bisa meledak

jika terbakar.

8. Hati-hati jangan sampai baterai jatuh atau

terbentur.

9. Jangan menggunakan baterai yang rusak.

SIMPAN PETUNJUK INI.

Tip untuk menjaga agar umur pemakaian

baterai maksimum

1. Ganti baterai sebelum habis sama sekali.

Selalu hentikan penggunaan mesin dan ganti

baterai jika Anda melihat bahwa mesin kurang

tenaga.

2. Jangan pernah mengisi ulang baterai yang sudah

diisi penuh.

Pengisian ulang yang berlebih memperpendek

umur pemakaian baterai.

3. Isi ulang baterai pada suhu ruangan 10°C - 40°C.

Biarkan baterai yang panas menjadi dingin

terlebih dahulu sebelum diisi ulang.

4. Isi ulang baterai sekali dalam enam bulan jika

Anda tidak menggunakannya dalam jangka waktu

yang lama.

DESKRIPSI FUNGSI

PERHATIAN:

•Selalu pastikan bahwa mesin dimatikan dan baterai

dilepas sebelum menyetel atau memeriksa kerja

mesin.

Memasang atau melepas baterai (Gb. 1)

•Selalu matikan mesin sebelum memasang atau

melepas baterai.

•Untuk melepas baterai, geser dari mesin sambil

menggeser tombol pada bagian depan baterai.

•Untuk memasang baterai, sejajarkan lidah baterai

dengan alur pada rumah dan masukkan ke dalam

tempatnya. Selalu masukkan seluruhnya sampai

terkunci pada tempatnya dan terdengar bunyi klik kecil.

Jika Anda bisa melihat indikator berwarna merah pada

sisi atas tombol, berarti tidak terkunci sepenuhnya.

Pasang sepenuhnya sampai indikator berwarna merah

tidak terlihat. Jika tidak, bisa terlepas dari mesin secara

tidak sengaja, menyebabkan luka pada Anda atau

orang di sekitar Anda.

•Jangan dipaksakan ketika memasang baterai. Jika

baterai tidak bergeser dengan mudah, berarti tidak

dimasukkan dengan benar.

Sistem perlindungan baterai (Baterai

Litium-ion dengan tanda bintang) (Gb. 2)

Untuk model BDF453

Baterai Litium-ion dengan tanda bintang yang dilengkapi

dengan sistem perlindungan. Sistem ini memutus daya ke

mesin secara otomatis untuk memperpanjang umur

pemakaian baterai.

Mesin akan berhenti saat penggunaan saat mesin dan/

atau baterai berada dalam salah satu kondisi berikut ini:

•Kelebihan beban:

Mesin dijalankan dengan cara yang

menyebabkannya menarik arus tinggi yang tidak

normal.

Untuk situasi ini, lepas picu saklar pada mesin dan

hentikan penggunaan yang menyebabkan mesin

mengalami kelebihan beban. Kemudian tarik lagi picu

saklarnya untuk mengoperasikannya kembali.

Jika mesin tidak menyala, baterai mengalami

kelebihan panas. Untuk situasi ini, biarkan baterai

menjadi dingin sebelum menarik picu saklarnya lagi.

•Tegangan baterai rendah:

Kapasitas baterai yang tersisa terlalu rendah dan

mesin tidak akan beroperasi. Untuk situasi ini, lepas

dan isi ulang baterai.

Kerja saklar (Gb. 3)

PERHATIAN:

•Sebelum memasukkan baterai pada mesin, pastikan

picu saklar berfungsi dengan baik dan kembali ke

posisi “OFF” saat dilepas.

Untuk menjalankan mesin, cukup tarik picu saklarnya.

Kecepatan mesin akan meningkat dengan menambah

tekanan pada picu saklar. Lepaskan picu saklar untuk

berhenti.

Kerja saklar pembalik arah (Gb. 4)

Mesin ini memiliki saklar pembalik arah untuk mengubah

arah putaran. Tekan tuas saklar pembalik arah dari sisi A

untuk putaran searah jarum jam atau dari sisi B untuk

putaran berlawanan arah jarum jam.

Ketika tuas saklar pembalik arah pada posisi netral, picu

saklar tidak bisa ditarik.

PERHATIAN:

•Selalu periksa arah putaran sebelum penggunaan.

•Gunakan saklar pembalik arah hanya setelah mesin

benar-benar berhenti. Mengubah arah putaran

sebelum mesin berhenti dapat merusak mesin.

•Saat mesin tidak digunakan, selalu posisikan tuas

saklar pembalik arah pada posisi netral.

Perubahan kecepatan (Gb. 5)

Untuk mengubah kecepatan, pertama-tama matikan

mesin dan kemudian geser tuas pengubah kecepatan ke

sisi “2” untuk kecepatan tinggi atau “1” untuk kecepatan

rendah. Pastikan bahwa tuas pengubah kecepatan

diposisikan pada posisi yang tepat sebelum penggunaan.

Gunakan kecepatan yang tepat untuk pekerjaan Anda.

PERHATIAN:

•Selalu posisikan tuas pengubah kecepatan

sepenuhnya pada posisi yang tepat. Jika Anda

menggunakan mesin dengan tuas pengubah

kecepatan berada di posisi tengah antara sisi “1” dan

sisi “2”, mesin bisa rusak.

•Jangan menggunakan tuas pengubah kecepatan

ketika mesin sedang bekerja. Mesin bisa rusak.

Menyetel torsi pengencangan (Gb. 6)

Torsi pengencangan bisa disetel dalam 17 tahap dengan

memutar cincin penyetel sehingga skalanya disejajarkan

dengan penunjuk pada badan mesin. Torsi

pengencangannya minimum ketika angka 1 disejajarkan

dengan penunjuk, dan maksimum ketika tanda

disejajarkan dengan penunjuk.

Kopeling akan bergeser pada tingkat torsi yang berbeda-

beda ketika disetel pada angka 1 sampai 16. Kopeling

dirancang untuk tidak bergeser pada tanda .

Sebelum penggunaan yang sebenarnya, pasang sekrup

percobaan pada bahan atau potongan bahan lain untuk

menentukan tingkat torsi yang dibutuhkan untuk

keperluan tertentu.

PERAKITAN

PERHATIAN:

•Selalu pastikan bahwa mesin dimatikan dan baterai

dilepas sebelum melakukan pekerjaan apapun pada

mesin.

Memasang atau melepas mata obeng atau

mata bor (Gb. 7)

Putar selongsong berlawanan arah jarum jam untuk

membuka rahang cekam. Masukkan mata bor ke dalam

cekam sejauh mungkin. Putar selongsong searah jarum

jam untuk mengencangkan cekam.

Untuk melepas mata mesin, putar selongsong

berlawanan arah jarum jam.

PENGGUNAAN

PERHATIAN:

•Selalu masukkan baterai seluruhnya sampai terkunci

pada tempatnya dan terdengar bunyi klik kecil. Jika

Anda bisa melihat bagian berwarna merah pada sisi

atas tombol, berarti tidak terkunci sepenuhnya.

Masukkan sepenuhnya sampai bagian berwarna

merah tidak terlihat. Jika tidak, bisa terlepas dari mesin

secara tidak sengaja, menyebabkan luka pada Anda

atau orang di sekitar Anda.

Pekerjaan pemasangan sekrup (Gb. 8)

PERHATIAN:

•Setel cincin penyetel pada tingkat torsi yang tepat

untuk pekerjaan Anda.

Posisikan ujung mata obeng pada kepala sekrup dan beri

tekanan pada mesin. Jalankan mesin dengan perlahan

dan kemudian tingkatkan kecepatan secara bertahap.

Lepas picu saklar segera setelah kopeling memotong.

PERHATIAN:

•Pastikan bahwa mata obeng dimasukkan lurus

terhadap kepala sekrup, atau sekrup dan/atau mata

bor bisa rusak.

CATATAN:

•Ketika memasang sekrup kayu, lakukan pengeboran

awal untuk membuat lubang pengarah agar

mempermudah pemasangan sekrup dan untuk

mencegah pecahnya benda kerja. Lihat tabel.

006421

Pekerjaan pengeboran

Pertama-tama, putar cincin penyetel sehingga penunjuk

mengarah pada tanda . Kemudian lakukan

sebagaimana berikut.

Mengebor kayu

Bila mengebor kayu, hasil terbaik didapat dengan mata

bor kayu yang dilengkapi sekrup pemandu. Sekrup

pemandu mempermudah pengeboran dengan menarik

mata bor ke dalam benda kerja.

Mengebor logam

Untuk mencegah mata bor selip ketika mulai membuat

lubang, buatlah takik dengan penitik lalu palu pada titik

yang akan dilubangi. Letakkan ujung mata bor pada takik

dan mulailah membor.

Gunakan cairan pendingin saat mengebor logam.

Pengecualian untuk besi dan kuningan yang harus dibor

kering.

PERHATIAN:

•Menekan mesin secara berlebihan tidak akan

mempercepat pengeboran. Bahkan, tekanan yang

berlebihan hanya akan merusak mata bor Anda,

mengurangi kinerja mesin dan memperpendek usia

mesin.

•Akan timbul gaya yang sangat kuat pada mesin/mata

bor saat menembus lubang. Pegang mesin dengan

kuat dan berhati-hatilah saat mata bor menembus

benda kerja.

•Mata bor yang macet dapat dicabut dengan menyetel

saklar pembalik arah agar mesin berputar berlawanan

arah untuk mundur. Tetapi, mesin bisa saja mundur

mendadak jika Anda tidak memegangnya dengan kuat.

• Tahan benda kerja berukuran kecil dengan penjepit

atau alat penahan lain.

•Jika mesin terus-menerus digunakan sampai baterai

habis, istirahatkan mesin selama 15 menit sebelum

melakukannya lagi dengan baterai yang penuh.

PERAWATAN

PERHATIAN:

•Selalu pastikan bahwa mesin dimatikan dan baterai

dilepas sebelum melakukan pemeriksaan atau

perawatan.

•Jangan sekali-kali menggunakan bensin, tiner, alkohol,

atau bahan sejenisnya. Penggunaan bahan demikian

dapat menyebabkan perubahan warna, perubahan

bentuk atau timbulnya retakan.

Untuk menjaga KEAMANAN dan KEANDALAN mesin,

perbaikan, perawatan atau penyetelan lain harus

dilakukan oleh Pusat Layanan Resmi Makita dan selalu

gunakan suku cadang pengganti buatan Makita.

PILIHAN AKSESORI

PERHATIAN:

•Dianjurkan untuk menggunakan aksesori atau

perangkat tambahan ini dengan mesin Makita Anda

yang ditentukan dalam petunjuk ini. Penggunaan

aksesori atau perangkat tambahan lain bisa

menyebabkan risiko cedera pada manusia. Hanya

gunakan aksesori atau perangkat tambahan sesuai

dengan peruntukkannya.

Jika Anda memerlukan bantuan lebih rinci berkenaan

dengan aksesori ini, tanyakan pada Pusat Layanan

Makita terdekat.

•Mata bor

•Mata sekrup

•Macam-macam jenis baterai dan pengisi daya asli

buatan Makita.

•Adaptor pengisi otomatis

•Tas jinjing plastik

CATATAN:

•Beberapa item dalam daftar tersebut mungkin sudah

termasuk dalam paket mesin sebagai aksesori standar.

Hal tersebut dapat berbeda dari satu negara ke negara

lainnya.

Diameter nominal sekrup

kayu (mm)

Ukuran lubang pengarah

yang dianjurkan (mm)

3,1 2,0 - 2,2

3,5 2,2 - 2,5

3,8 2,5 - 2,8

4,5 2,9 - 3,2

4,8 3,1 - 3,4

5,1 3,3 - 3,6

5,5 3,7 - 3,9

5,8 4,0 - 4,2

6,1 4,2 - 4,4

TING VIT

Gii thích v hình v tng th

THÔNG S K THUT

•Do chng trình nghiên cu và phát trin liên tc ca chúng tôi nên các thông s k thut trong ây có th thay i mà

không cn thông báo trc.

•Các thông s k thut và hp pin có th thay i tùy theo tng quc gia.

•Trng lng có hp pin tùy theo Quy trình EPTA tháng 01/2003

END004-4

Ký hiu

Phn di ây cho bit các ký hiu c dùng cho thit

b. m bo rng bn hiu rõ ý ngha ca các ký hiu này

trc khi s dng.

..... c tài liu hng dn.

ENE034-1

Mc ích s dng

Dng c này c dùng  khoan và bt vít vào g, kim

loi và nha.

GEA006-2

Cnh báo An toàn Chung dành

cho Dng c Máy

CNH BÁO! c tt c các cnh báo an toàn và

hng dn. Vic không tuân theo các cnh báo và

hng dn có th dn n in git, ho hon và/hoc

thng tích nghiêm trng.

Lu gi tt c cnh báo và hng

dn  tham kho sau này.

Thut ng “dng c máy” trong các cnh báo  cp n

dng c máy (có dây) c vn hành bng ngun in

chính hoc dng c máy (không dây) c vn hành

bng pin ca bn.

An toàn ti ni làm vic

1. Gi ni làm vic sch s và có  ánh sáng. Ni

làm vic ba bn hoc ti thng d gây ra tai nn.

2. Không vn hành dng c máy trong môi tr

ng

cháy n, ví d nh môi trng có s hin din

ca các cht lng, khí hoc bi d cháy. Các dng

c máy to tia la in có th làm bi hoc khí bc

cháy.

3. Gi tr em và ngi ngoài tránh xa ni làm vic

khi ang vn hành dng c máy. S xao lãng có th

khin bn mt kh nng kim soát.

An toàn v in

4. Phích c

m ca dng c máy phi khp vi  cm.

Không bao gi c sa i phích cm theo bt

k cách nào. Không s dng bt k phích chuyn

i nào vi các dng c máy c ni t (tip

t). Các phích cm còn nguyên vn và  cm phù

hp s gim nguy c in git.

5. Tránh  c th tip xúc vi các b m

t ni t

hoc tip t nh ng ng, b tn nhit, bp ga

và t lnh. Nguy c b in git s tng lên nu c

th bn c ni t hoc tip t.

6. Không  dng c máy tip xúc vi ma hoc

trong iu kin m t. Nc lt vào dng c

 máy

s làm tng nguy c in git.

7. Không lm dng dây. Không bao gi s dng dây

 mang, kéo hoc tháo phích cm dng c máy.

Gi dây tránh xa ngun nhit, du, các mép sc

hoc các b phn chuyn ng. Dây b hng hoc

b ri s làm tng nguy c in git.

8. Khi vn hành dng c máy ngoài tri, hãy s

dng dây kéo dài phù hp cho vi

c s dng ngoài

tri. Vic dùng dây phù hp cho vic s dng ngoài

tri s gim nguy c in git.

1. Ch báo màu 

2. Nút

3. Hp pin

4. Du sao

5. Cn khi ng công tc

6. Cn công tc o chiu

7. Cn thay i tc 

8. Vòng iu chnh

9. Vòng chia 

10. Vch chun

11. Tr ngoài

KiuBDF343BDF453

Công sut

Thép 10 mm 13 mm

G 25 mm 36 mm

Vít bt g 5,1 mm x 63 mm 6 mm x 75 mm

Vít máy 6 mm

Tc  không ti (phút

-1

)

Cao (2) 0 - 1.300

Thp (1) 0 - 400

Chiu dài tng th 192 mm 214 mm

Trng lng tnh 1,4 kg 1,6 kg

Hiu in th nh mcD.C. 14,4 VD.C. 18 V

9. Nu bt buc phi vn hành dng c máy  ni

m t, hãy s dng ngun in có b ngt mch

ni t khi rò in (GFCI). Vic s dng GFCI s

gim nguy c in git.

An toàn cá nhân

10. Luôn tnh táo, quan sát nhng vic bn ang làm

và s dng nhng phán oán theo kinh nghim

khi vn hành dng c máy. Không s

 dng dng

c máy khi bn ang mt mi hoc chu nh

hng ca ma túy, ru hay thuc. Ch mt

khonh khc không tp trung khi ang vn hành dng

c máy cng có th dn n thng tích cá nhân

nghiêm trng.

11. S dng thit b bo h cá nhân. Luôn eo thit b

bo v mt. Các thit b bo h

nh mt n chng

bi, giày an toàn chng trt, m bo h hay thit b

bo v thính giác c s dng trong các iu kin

thích hp s giúp gim thng tích cá nhân.

12. Tránh vô tình khi ng dng c máy. m bo

công tc  v trí off (tt) trc khi ni ngun in

và/hoc b pin, cm hoc mang dng c máy. Vic

mang dng c máy khi ang t ngón tay  v trí công

tc hoc cp in cho dng c máy ang bt thng

d gây ra tai nn.

13. Tháo mi khóa hoc chìa vn iu chnh trc khi

bt dng c máy. Vic chìa vn hoc khóa vn còn

gn vào b phn quay ca dng c máy có th dn

n thng tích cá nhân.

14. Không vi quá cao. Luôn gi thng b

ng tt và có

ch  chân phù hp. iu này cho phép iu khin

dng c máy tt hn trong nhng tình hung bt ng.

15. n mc phù hp. Không mc qun áo rng hay

eo  trang sc. Gi tóc, qun áo và gng tay

tránh xa các b phn chuyn ng. Qun áo rng,

 trang sc hay tóc dài có th mc vào các b phn

chuyn ng.

16. Nu các thit b

c cung cp  kt ni các thit

b thu gom và hút bi, hãy m bo chúng c

kt ni và s dng hp lý. Vic s dng thit b thu

gom bi có th làm gim nhng mi nguy him liên

quan n bi.

S dng và bo qun dng c máy

17. Không dùng lc i vi dng c máy. S dng

úng dng c máy cho công vic c

a bn. S

dng úng dng c máy s giúp thc hin công vic

tt hn và an toàn hn theo giá tr nh mc c

thit k ca dng c máy ó.

18. Không s dng dng c máy nu công tc không

bt và tt c dng c máy ó. Mi dng c máy

không th iu khin c bng công tc

u rt

nguy him và cn c sa cha.

19. Rút phích cm ra khi ngun in và/hoc ngt

kt ni b pin khi dng c máy trc khi thc

hin bt k công vic iu chnh, thay i ph

tùng hay ct gi dng c máy nào. Nhng bin

pháp an toàn phòng nga này s gim nguy c vô

tình khi ng dng c máy.

20. C

t gi các dng c máy không s dng ngoài

tm vi ca tr em và không cho bt k ngi nào

không có hiu bit v dng c máy hoc các

hng dn này vn hành dng c máy. Dng c

máy s rt nguy him nu c s dng bi nhng

ngi dùng cha qua ào to.

21. Bo qun dng c máy. Kim tra tình trng lch

c hoc bó kp ca các b phn chuyn ng,

hin tng nt v ca các b phn và mi tình

trng khác mà có th nh hng n hot ng

ca dng c máy. Nu có hng hóc, hãy sa cha

dng c máy trc khi s dng. Nhiu tai nn xy

ra là do không bo qun tt dng c máy.

22. Luôn gi cho dng c c

t c sc bén và sch

s. Nhng dng c ct c bo qun tt có mép ct

sc s ít b kt hn và d iu khin hn.

23. S dng dng c máy, ph tùng và u dng c

ct, v.v... theo các hng dn này, có tính n iu

kin làm vic và công vic c thc hin. Vic s

d

ng dng c máy cho các công vic khác vi công

vic d nh có th gây nguy him.

S dng và bo qun dng c dùng pin

24. Ch sc pin li vi b sc do nhà sn xut quy

nh. B sc phù hp vi mt loi b pin này có th

gây ra nguy c ha hon khi c dùng cho mt b

pin khác.

25. Ch s dng các dng c máy vi các b pin 

quy nh c th. Vic s dng bt c b pin nào

khác có th gây ra thng tích và ha hon.

26. Khi không s dng b pin, hãy gi tránh xa các 

vt khác bng kim loi, chng hn nh kp giy,

tin xu, chìa khóa, inh, c vít hoc các vt nh

bng kim loi mà có th làm ni tt các u cc

pin. Các u cc pin b on mch có th

 gây cháy

hoc ha hon.

27. Trong iu kin s dng quá mc, pin có th b

chy nc; hãy tránh tip xúc. Nu vô tình tip

xúc vi pin b chy nc, hãy ra sch bng

nc. Nu dung dch t pin tip xúc vi mt, cn

i khám bác s thêm. Dung dch chy ra t pin có th

gây rát da hoc bng.

Bo dng

28.  nhân viên sa cha 

trình  bo dng

dng c máy ca bn và ch s dng các b phn

thay th ng nht. Vic này s m bo duy trì

c  an toàn ca dng c máy.

29. Tuân theo hng dn dành cho vic bôi trn và

thay ph tùng.

30. Gi tay cm khô, sch, không dính du và m.

GEB088-1

CNH BÁO AN TOÀN I VI

MÁY KHOAN BT VÍT DÙNG PIN

1. S dng các tay cm ph nu c cung cp kèm

theo dng c. Không iu khin c dng c s

gây ra thng tích cho con ngi.

2. Cm dng c máy bng b mt kp cách in khi

thc hin mt thao tác trong ó ph kin ct có

th tip xúc vi dây dn kín. B phn ct tip xúc

vi dây dn “có i

n” có th khin các b phn kim

loi b h ca dng c máy “có in” và làm cho ngi

vn hành b in git.

3. Cm dng c máy bng b mt kp cách in khi

thc hin mt thao tác trong ó b phn kp có

th tip xúc vi dây dn in kín bên di. B

phn kp tip xúc v

i dây dn “có in” có th khin

các b phn kim loi b h ca dng c máy “có in”

và làm cho ngi vn hành b in git.

4. Luôn chc chn rng bn có ch ta chân vng

chc.

m bo rng không có ai  di khi dùng dng

c  nhng v trí trên cao.

5. Cm chc dng c.

6. Gi tay tránh xa các b phn quay.

7. Không  mc dng c hot ng. Ch vn hành

dng c khi cm trên tay.

8. Không chm vào u mi khoan hay vt gia công

ngay sau khi vn hành; chúng có th rt nóng và

có th gây bng da.

9. Mt s vt liu có cha các hóa cht có th rt

c hi. Phi cn trng tránh hít phi bi và 

tip xúc vi da. Tuân theo các thông tin v an toàn

ca nhà cung cp i vi mi loi vt liu.

LU GI CÁC HNG DN NÀY.

CNH BÁO:

KHÔNG c  s thoi mái hay quen thuc vi sn

phm (có c do s dng nhiu ln) thay th vic

tuân th nghiêm ngt các quy nh v an toàn dành

cho sn phm này. VIC DÙNG SAI hoc không tuân

theo các quy nh v an toàn c nêu trong tài liu

hng dn này có th dn n thng tích cá nhân

nghiêm trng.

ENC007-7

CÁC HNG DN AN TOÀN

QUAN TRNG

I VI HP PIN

1. Trc khi s dng hp pin, hãy c k tt c các

hng dn và du hiu cnh báo trên (1) b sc

pin, (2) pin và (3) sn phm s dng pin.

2. Không tháo ri hp pin.

3. Nu thi gian vn hành ngn hn nhiu, dng

vic vn hành ngay lp tc. iu này có th gây

nguy c quá nhit, gây cháy hoc thm chí gây

n.

4. Nu cht in phân dính vào m

t bn, hãy ra

sch bng nc sch và i khám bác s ngay lp

tc. Vic này có th làm gim th lc ca mt bn.

5. Không c on mch hp pin:

(1) Không c chm vào các u cc bng vt

liu dn in.

(2) Tránh ct gi hp pin trong ch cha có các

vt kim loi khác nh inh, tin xu, v.v...

(3) Không 

c  hp pin tip xúc vi nc

hoc ma.

Pin b on mch có th gây ra dòng in ln,

gây quá nhit, cháy và thm chí gây phóng in.

6. Không c ct gi dng c và hp pin  nhng

ni nhit  có th vt quá 50°C.

7. Không c thiêu hy hp pin ngay c khi nó ã

b h hng nghiêm trng hoc hoàn toàn không

s dng c. H

p pin có th n khi b t cháy.

8. Cn thn không c làm ri hoc va p mnh

vào pin.

9. Không s dng pin ã h hng.

LU GI CÁC HNG DN NÀY.

Li khuyên  duy trì ti a tui th pin

1. Sc hp pin trc khi pin c x in hoàn toàn.

Luôn dng vic vn hành dng c và sc pin khi

bn nhn thy công sut dng c b gim.

2. Không bao gi sc li mt hp pin ã c sc

y.

Vic sc in thêm na s làm gim tui th pin.

3. Sc pin  nhit  phòng t 10°C - 40°C.  pin

ang nóng ngu

i li dn trc khi sc pin.

4. Sc hp pin mt ln mi sáu tháng nu bn không

s dng nó trong mt thi gian dài.

MÔ T CHC NNG

CN TRNG:

•Luôn m bo rng ã tt dng c và tháo hp pin ra

trc khi thc hin vic iu chnh hoc kim tra chc

nng trên dng c.

Lp hoc tháo g hp pin (Hình 1)

•Luôn tt dng c trc khi lp hoc tháo hp pin.

•  tháo hp pin, hãy trt nó ra t dng c trong lúc

trt nút  phía trc hp pin.

•  lp hp pin vào, hãy canh chnh phn cht ca hp

pin vào phn rãnh nm trên v và trt cht vào v trí.

Luôn trt ht mc n khi nào cht khóa úng vào v

trí vi mt ting click nh. Nu bn vn còn nhìn thy

ch

th màu  phía trên nút bm, cht vn cha c

khóa hoàn toàn. Lp cht hoàn toàn vào v trí cho n

khi không th nhìn thy ch th màu . Nu không,

cht có th vô tình ri ra khi dng c, gây thng tích

cho bn hoc ngi khác xung quanh.

•Không c n mnh khi lp hp pin. Nu hp pin

không nh nhàng trt vào v trí, có ngha là pin vn

cha c lp úng.

H thng bo v pin (Hp pin Lithium-ion

có du sao) (Hình 2)

i vi mô hình BDF453

Các pin Lithium-ion có du sao c trang b h thng

bo v. H thng này s t ng ngt ngun in n

dng c  kéo dài tui th pin.

Dng c s t ng dng vn hành khi dng c và/hoc

pin  mt trong nhng tình hung sau ây.

•B quá ti:

Dng c c vn hành theo cách gây ra mt dòng

i

n cao bt thng.

Trong trng hp này, hãy nh cn khi ng công

tc và ngng thao tác làm cho dng c b quá ti.

Sau ó kéo cn khi ng công tc mt ln na 

khi ng li dng c.

Nu dng c không khi ng, pin ang b quá nhit.

Trong trng hp này, hãy  pin ngui li trc khi

kéo cn khi ng công tc m

t ln na.

• in th pin thp:

Dung lng pin còn li quá thp và dng c s không

hot ng. Trong trng hp này, hãy tháo pin và

sc li pin.

Hot ng công tc (Hình 3)

CN TRNG:

•Trc khi lp hp pin vào dng c, luôn luôn kim tra

xem cn khi ng công tc có hot ng bình thng

hay không và tr v v trí “OFF” (TT) khi nh ra.

 khi ng dng c, ch cn kéo cn khi ng công

tc. Tc  dng c c gim xung bng cách tng lc

ép lên cn khi ng công tc. Nh cn kh

i ng công

tc ra  dng.

Hot ng công tc o chiu (Hình 4)

Dng c này có mt công tc o chiu  thay i chiu

xoay. Nhn nút công tc o chiu t mt A  xoay theo

chiu kim ng h hoc t mt B  xoay ngc chiu

kim ng h.

Khi nút công tc o chiu  v trí chính gia, không th

kéo cn khi ng công tc c.

CN TRNG:

•Luôn luôn kim tra hng xoay trc khi vn hành.

•Ch s

 dng công tc o chiu sau khi dng c ã

dng hoàn toàn. Vic thay i hng xoay trc khi

dng c dng có th làm hng dng c.

•Khi vn hành dng c, luôn t nút công tc o chiu

 v trí chính gia.

Thay i tc  (Hình 5)

 thay i tc , u tiên hãy tt dng c và trt cn

thay i tc  sang v trí “2”  có tc  cao hoc v trí

“1”  có tc  thp. m bo rng cn thay i tc 

c t  úng v trí trc khi vn hành. S dng úng

tc  cho công vic ca bn.

CN TRNG:

•Luôn  c

n thay i tc  vào tht úng v trí. Nu

bn vn hành dng c vi cn thay i tc  t 

mt na gia v trí “1” và “2”, dng c có th b h

hng.

•Không c s dng cn thay i tc  trong lúc

dng c ang chy. Dng c có th b h hng.

iu chnh lc vn xit (Hình 6)

Lc vn xit có th c iu chnh theo 17 nc bng

cách xoay vòng iu chnh  canh chnh các  chia vào

vch chun trên thân dng c. Lc vn xit t ti thiu

khi s 1 c cn chnh vào vch chun và t ti a khi

du hiu c cn chnh vào vch chun.

B ly hp s trt  các m

c lc xon khác nhau khi

c cài t s 1 n s 16. B ly hp này không c

thit k  trt n du hiu .

Trc khi vn hành thc t, hãy bt th mt c vít vào vt

liu hoc mu vt liu tng t  xác nh mc lc xon

nào cn cho ng dng c th ó.

LP RÁP

CN TRNG:

•Luôn m bo rng ã tt dng c và tháo hp pin ra

trc khi thc hin bt c thao tác nào trên dng c.

Lp t hoc tháo mi vn hoc mi

khoan (Hình 7)

Xoay tr ngoài ngc chiu kim ng h  m các ngàm

kp. t u mi vào trong ngàm kp ht mc có th.

Xoay tr ngoài theo chiu kim ng h  vn cht ngàm

kp.

 tháo u mi, xoay tr ngoài ngc chiu kim ng

h.

VN HÀNH

CN TRNG:

•Luôn luôn lp hp pin vào ht mc cho n khi nó khóa

úng vào v trí. Nu bn vn còn nhìn thy phn màu

 phía trên nút bm, cht vn cha c khóa hoàn

toàn. Lp cht hoàn toàn vào v trí cho n khi không

th nhìn thy phn màu . Nu không, cht có th vô

tình ri ra khi dng c, gây thng tích cho bn hoc

ngi khác xung quanh.

Thao tác bn vít (Hình 8)

CN TRNG:

•Chnh nút iu chnh n cp  lc vn phù hp vi

công vic ca bn.

t nh mi vn vào trong u vít và nhn dng c. Khi

ng dng c t t, sau ó tng tc  dn dn. Nh cn

khi ng công tc ngay khi b ly hp va ngt.

CN TRNG:

• 

m bo rng mi vn c lp thng ng vào u

vít, nu không vít và/hoc mi vn có th b h hng.

LU Ý:

•Khi vn các vít bt g, hãy khoan trc các l nh

hng  giúp bt vít d dàng hn và ngn vt gia

công b chia tách. Xem s .

006421

Thao tác khoan

u tiên, xoay nút iu chnh sao cho vch chun ch vào

du . Sau ó tin hành nh sau.

Khoan vào g

Khi khoan vào g,  có kt qu tt nht cn s dng các

mi khoan dùng  khoan g và vít dn. Vít dn giúp

khoan d dàng hn bng cách kéo u mi vào trong vt

gia công.

Khoan vào kim loi

 phòng nga u mi b trt ra lúc bt u khoan l,

hãy to mt vt lõm bng cách dùng dùi c tâm và

óng

vào im cn khoan. t u mi khoan vào ch lõm này

và bt u khoan.

S dng du nhn  ct khi khoan kim loi. Tr các

trng hp dùng st và ng thau cn phi c khoan

khô.

ng kính danh nh

ca vít bt g (mm)

Kích thc khuyn cáo

ca l khoan dn (mm)

3,1 2,0 - 2,2

3,5 2,2 - 2,5

3,8 2,5 - 2,8

4,5 2,9 - 3,2

4,8 3,1 - 3,4

5,1 3,3 - 3,6

5,5 3,7 - 3,9

5,8 4,0 - 4,2

6,1 4,2 - 4,4

CN TRNG:

•Nhn dng c quá mc s không tng tc  khoan lên

c. Trên thc t, vic nhn mnh thêm này s ch

làm gây hng u mi ca bn, gim hiu nng và tui

th hot ng ca dng c.

•S có lc quán tính rt ln trên dng c/mi khoan lúc

l khoan c xuyên thng. Gi cht dng c và

chun b ghìm lc quán tính li khi mi khoan xuyên

thng vt gia công.

•Mi khoan b kt có th c tháo ra n gin bng

cách t công tc o chiu sang ch  xoay ngc

li  rút mi khoan ra. Tuy nhiên, dng c có th quay

ngc ra bt ng nu bn không gi cht.

•Luôn luôn gi cht các vt gia công có kích thc nh

bng kìm hoc dng c kp tng t

•Nu dng c c vn hành liên tc cho n khi hp

pin ã b x kit, hãy  dng c ngh 15 phút trc khi

thc hin tip bng pin mi.

BO TRÌ

CN TRNG:

•Hãy luôn chc chn rng dng c ã c tt và hp

pin ã c tháo ra trc khi c gng thc hin vic

kim tra hay bo dng.

•Không bao gi dùng xng, ét xng, dung môi, cn

hoc hóa cht tng t. Có th xy ra hin tng mt

màu, bin dng hoc nt v.

 m bo AN TOÀN và TIN CY ca sn phm, vi

c

sa cha hoc bt c thao tác bo trì, iu chnh nào u

phi c thc hin bi các Trung tâm Dch v c y

quyn ca Makita (Makita Authorized Service Center),

luôn s dng các ph tùng thit b thay th ca Makita.

PH KIN TÙY CHN

CN TRNG:

•Các ph kin hoc ph tùng gn thêm này c

khuyn cáo s dng vi dng c Makita ca bn theo

nh quy nh trong hng dn này. Vic s dng bt

c ph kin hoc ph tùng gn thêm nào khác u có

th gây ra ri ro thng tích cho ngi. Ch s dng

ph kin hoc ph tùng gn thêm cho mc ích ã quy

nh s

n ca chúng.

Nu bn cn h tr  bit thêm chi tit v nhng ph

kin này, hãy liên h vi Trung tâm Dch v ca Makita ti

a phng ca bn.

•Các mi khoan

•Các u mi vít

•Các loi pin và b sc chính hãng ca Makita

•B chuyn i sc pin t ng làm ti

•Hp nha cha dng c

LU Ý:

•Mt vài mc trong danh sách có th

c bao gm

trong gói dng c làm ph kin tiêu chun. Các thông

s k thut có th thay i tùy theo tng quc gia.

!"#"$%&

'(")*+,"&-)./0//).%123$4

!"#$%&'()*+),

! !"#$%&'())(*+,"+-,(-.'/01234/5"(%06(&

76%!"#$%& 8,%9:2';(!4(3<"!%)=(*>?/?"@A%('

!B2@$0"1B2&CD,ED0C967,%&1',&<F,G*(?26-&F",(

! 8,%9:2';(!4(312372/?1?7!7%*@$%('17)76(&)/"CB<"17623B*3!GH

! "A;(F"/)*-972/?1?7!7%*@$7(98,%?/&+/?8%& EPTA 01/2003

END004-4

!"#$"%&'(

76%CB"@A+#%=/I2/)JKLG@$<M,=;(F*/?%NB)*KL EB*DHO)J(+-(9F9(0

8%&=/I2/)JKL<F,!8,(<')6%")(*<M,&("

..... %6("+:69#%)(*<M,&("

ENE034-1

!"#$%&'()*+,(-)%./,(0.,

!+*#$%&9#%"@A<M,=;(F*/?!'(31238/"=)*:2&<"C9, E2F3 12342(=7.)

GEA006-2

!"#$%&'()*#(!+#,-.')/012'3

$!4&5'3,&'6778#905+6-

!"#$%&'(! ')#(!"#$%&'(*+#(!,#-./'*0123/4!"#3(4(5

61789-*

!"#$%&'()*+,),"%-."/,012345-."3252."6+7!4&"81"9:&7

;4<=>/!)6$??@"AB1, $?$=%> 345/=#01$6>#+**"6/9 B*1C&"7#>"C3#7

*-./01-2)3()*45#67&,3()76,6()819:;$<

=>"*?@6!"#$%&#"):#A:B6#6)34

!"#$%# !&!'()*+,(*-../#" 01!"#&2(*11345,#678+&!'()*+,(*-../# (,39#6)

:3):"#+#1;<60=>?'@A9-../#5'(*&!'()*+,(*-../# (-'>9#6) :3):"#+#1;<6

0=>AB2&2*'3)

)120$3,#456+,(7.89:;/:<2(29

!"#$%&'()*+),-.-(/012*34-2567-!#$62*#5.8954:-.

!"#$%&'

()(*+)*(*)*,("-."/%01-23$4256789)2(+):/-;1<= :+,=;5/>

2. ,6=2>?@(29-)%./,(0 .,ABBC2>9'427:;/,2!-DE#D2%%&-FE#

-?=9 >9'G29:;/:;/0;+,(-H31 DI2J H%.,K"L9M(:;/0;)"N'0F5OE

A1AB !+*#$%&9#%CPPQ('3=*,(&B*3)(0CP!4#$%'NDM"-"R N6"S&

F*#%)T(UD/&)26(-

*:3/;-)<9+-=$*>?@ 9A&'BC!!/'&D('2:)<(BAE$,F6 =D?"#/18<G+

$!A&D'8-&';HHI#

!"#%D:)E7#*!82:%"F)1"9G."<=>-HI:JK/:DC

!"#-8*-H%

1. CP1=D&=V("3=@1D&

2. BNW9

3. 72/?1?7!7%*@$

4. !+*#$%&F9(0D(-

5. =-.7ML=/$&&("

6. ),("=-.7ML!B2@$0"G.HG(&

7. ),("!B2@$0"+-(9!*X-

8. 1F-"B*/?

9. !28?%)*3D/?

10. 2:)H*M@A

11. B2%)

*N6" BDF343 BDF453

+-(9=(9(*V<")(*!'(3

E2F3 10 99.13 99.

C9, 25 99.36 99.

=)*:0ODC9, 5.1 99. x 63 99.6 99. x 75 99.

=)*:0ODE2F3 6 99.

+-(9!*X-8K3F9N"!B26( (*%?76%"(G@)

=:& (2) 0 - 1,300

7$;( (1) 0 - 400

+-(90(-ED0*-9 192

99.214 99.

"A;(F"/)=NGY. 1.4 )).1.6 )).

1*&D/"CPPQ( )*31=7*& 14.4 E-27L )*31=7*& 18 E-27L

)120$3,#456#@29ABBC2

4. $35PD+,(-)%./,(0.,ABBC2O@,(7,#;D5F-O@2%5F ,6 =2#5#Q$3(

$35PDA0=1=2D%N;>#R ,6=2>?@$35PD,&Q#S$-O,%*D5F

-)%./,(0.,

ABBC2:;/O=,'26#E9 B2/Z)G@$C96V:)D/D1B2&123!7,(*/?CPG@$!8,()/"

4%D@'3M6-02D+-(9!=@$0&8%&)(*!).DCPPQ(MX%7

5. %&15(,6=2>H@%=2(D26'50M5'D5F7.89ME1:;/O=,'26#E9 -?=9 :=,

-)%./,(9<2)120%@,9 -O2H"(O@0 Q3&OT@-6S9 9@+-(9!=@$0&G@$'3

!).DCPPQ(MX%7=:&8OA" F()*6(&)(08%&+NK=/9S/=) /?4#A"

6. ,6=2>H@-)%./,(0.,ABBC2GTD98<2H%.,,6T=>9'427-$U6D?.89 "A;(

G@$CF2!8,(CB<"!+*#$%&9#%CPPQ('3!4.$9+-(9!=@

60&8%&)(*!).D

CPPQ(MX%7

7. ,6=2>?@'26AB,6=2(A0=-H02&'0 ,6=2>?@'26AB-7./,6D #V(

H%.,G,#$35PD-)%./,(0.,ABBC2 -DSF'26AB>H@H=2(!2D)120

%@,9 98<2059 +,(0;)0 H%.,?E89'=19:;/-)3./,9:;/ =(0G@$M;(*ND

F*#%4/")/"'3!4.$9+-(9!=@$0&8%&)(*!).DCPPQ(M X%7

8. +N&:;/>?@(29-)%./,(0.,ABBC29,D,2)2% )1%>?@'26O=,

7=1(:;/-H02&'0D5F(294269,D,2)2% )(*<M,=(0G@$

!F9(3=9)/?&("[(0"%)%(+(*'32D+-(9!=@$0&8%&)(*!).D

CPPQ(MX%7

!"#$%&'()%'"*+,-./&'0.&1223"(*45"*67/+89:#) .;* (!%()%

&<8#-=>$?@A'B-+0./&07#-CD41223"-?/AE'@F* (GFCI)

!"#$%&

GFCI '()*+,"-./0123453!"#.!6*7889"%:5;

)120$3,#456'=19F"))3

10. >H@%&05#%&15(Q3&'5(-DO-'0,1=2)"ND<235(:<2'E/(>#,6T=

Q3&>?@'205W'<29VD>9+N&>?@(29-)%./,(0.,ABBC2 ,6=2

>?@(29-)%./,(0.,ABBC2>9+N&:;/)"ND<235(-H9./,6 H%.,>9

'427:;/0V9-02!2D62-'7OE# -)%./,(#./0 Q,3D,X,3* H%.,

D2%>?@62 M/$-8K3G@$8(D+-(9*39/D*3-/&!9#$%);(2/&<M,&("

!+*#$%&9#%CPPQ(%('G;(<F,+NKCD,*/??(D!'X?%06(&*N"1*&

11. >?@,"$D%N*$C,(D59'=19F"))3 '10Q1=9O2$C,(D59-'0,

B)*KLBQ%&)/" !M6" F",()())/"RNW" *%&!G,(".*[/0)/"2#$" F9-)

".*[/0 F*#%!+*#$%&BQ%&)/")(*CD,0."G@$<M,<"=[(4G@$!F9(3=9'3

M6-02D)(*?(D!'X?

12. $C,(D59A0=>H@-$Y#>?@(29Z#6A0=O58(>! O%1!',F1 =2'1EO?*

,6T=>9O<2QH9=($Y#D=,9-?./,0O=,D5FQH3=(!=26AB Q3&/H%.,

?"#QFO-O,%;/ H%.,D=,9D2%6DH%.,G.,-)%./,(0., )(*=%D

".A-9#%?*.!-K=-.7ML!4#$%V#%!+*#$%&9#%CPPQ( F*#%)(*M(*L'CP

!+*#$%&9#%CPP

Q(<"8K3G@$!B\D=-.7ML%0:6%('";(CB=:6)(*!).D

%N?/7.!F7N

13. 9<2D"WQ!$%5FQO=(H%.,$%&Q!,,DD=,9:;/!&-$Y#-)% ./,(0.,

ABBC2 B*31'F*#%)NI1'G@$!=@0?+,(&%0:6<"M.A"=6-"G@$F9N"CD,8%&

!+*#$%&9#%CPPQ(%('G;(<F,+NKCD,*/??(D!'X?

14. ,6=2:<2(29>9%&6&:;/'"#-,.8,0 !5#:=2D2%6.9Q3&D2%:%(

O51>H@-H02&'0O3,#-132 !4*(3'3G;(<F,+-?+N9!+*#$%&9#%

CPPQ(CD,D@8OA"<"=V(")(*KLG@$C96+(D+.D

15. QO=(D26>H@-H02&'0 ,6=2'10-)%.

/,(QO=(D26:;/H310-DE9

A$ H%.,'10-)%./,($%&#5F #TQ3A0=>H@-'@9M0 -'.8,M@2 Q3&

G"(0.,,6T=>D3@?E89'=19:;/-)3./,9:;/ !=#A%S,(*N69*6(9 !+*#$%&B*3D/?

F*#%S9G@$9@+-(90(-%('!8,(CB7.D<"M.A"=6-"G@$!+2#$%"G@$

16. H2D0;D2%!5#,"$D%N*'<2H%5F#T#Q3&!5#-DSFK"L9A1 @>9

'G29:;/ >H@O%1!',F1=2A#@-?./,0O=,Q3&>?@(29,"$D%N*9589

,6=2(-H02&'0 )(*<M,!+*#$%&D:D123'/D!)X?RNW"'3M6-02D

%/"7*(0G@$!).D'()RNW"S&CD,

D2%>?@Q3&#TQ3-)%

./,(0.,ABBC2

17. ,6=2K[9>?@-)%./,(0.,ABBC2 >?@-)%./,(0.,ABBC2:;/-H02&'0

D5FD2%>?@(29+,()"N !+*#$%&9#%CPPQ(G@$!F9(3=9'3G;(<F,CD,

&("G@$9@B*3=.GY.[(4123B2%D[/0)-6(7(98@D+-(9=(9(*V

8%&!+*#$%&G@$CD,*/?)(*%%)1??9(

18. ,6=2>?@-)%./,(0.,ABBC2 H2D'1EO?*A0='202%G-$Y#$Y#A#@

!+*#$%&9#%CPPQ(G@$+-?+N9D,-0=-.7MLC96CD,!B]"=.$&%/"7*(0123

7,%&CD,*/?)(*U6%91U9

19. G,#$35PD!2DQH3=(!=26AB Q3&/H%.,?"#QFO-O,%;/,,D

!2D-)%./,(0.

,ABBC2D=,9:<2D2%$%5FQO=( -$3;/69, "$D%N*

-'%E0 H%.,!5#-DSF-)%./,(0.,ABBC2 -.Y@)(*BQ%&)/"D,("+-(9

B2%D[/0D/&)26(-'3M6-02D+-(9!=@$0&8%&)(*!B\D<M,&("

!+*#$%&9#%CPPQ(ED0C967/A&<'

20. !5#-DSF-)%./,(0.,ABBC2:;/A0=A#@>?@(29>H@H=2(!2D0.,-#SD

Q3&,6=2,9"W2O>H@F"))3:;/A0=)"@9-)6D5F-)%./,(0.,ABBC2

H%.,)<2Q9&9<2-H3=29;8>?@(29-)%./,(0.,ABBC2 !+*#$%&9#%

CPPQ('3!B]"%/"7*(0!9#$%%0

:6<"9#%8%&S:,G@$C9 6CD,*/?)(*R^)%?*9

21. D2%#TQ3%5D\2-)%./,(0.,ABBC2 O%1!',FD2%$%&D,F:;/

A0=GTDO@,(H%.,D2%-?./,0O=,+,(?E89'=19:;/-)3 ./,9

:;/ D2%

QODH5D+,(?E89'=19 H%.,'427,./9R :;/,2!'=(M3D%&:F

O=,D2%:<2(29+,(-)%./,(0.,ABBC2 H2D0;)120-';6H26 >H@

9<2-)%./,(0.,ABBC2A$J=,0QJ0D=,9D2%>?@(29 %N?/7.!F7N

';("-"9()!).D'())(*D:12*/)J(!+*#$%&9#%CPPQ(%06(&C96

V:)7,%&

22. 35F)120)0Q3&:<2)120'&,2#-)%./,(0.,D2%O5#,6T=-'0,

!+*#$%&9#%)(*7/DG@$9@)(*D:12%06(&V:)7,%&1239@8%?)(*7/D+9

9/)'39@B_IF(7.D8/D",%0123+-?+N9CD,&6(0)-6(

23. >?@-)%./,(0.,ABBC2 ,"

$D%N*-'%E0 Q3&15'#"'E89-$3.,( ]3]

O20)<2Q9&9<2#5(D3=21 7E!2%N2'427D2%:<2(29Q3&

(29:;/!&3(0.,:<2 )(*<M,!+*#$%&9#%CPPQ(!4#$%G;(&("%#$""%)

!F"#%'()G@$);(F"DC-,%('G;(<F,!).D%/"7*(0

D2%>?@Q3&#TQ3-)%./,(0.,QFO-O,%;/

24. ?2%*!AB>H0=#@16-)%./,(?2%*!:;/%&F"Z#6MT@M3EO-:=29589

!+*#$%&M(*L'G@$!F9(3=;(F*/?MND1?7!7%*@$B*3![GF"O$&%('9@

+-(9!=@$0&G@$'3!).DCPCF9,!9#$%";(CB<M,)/?MND1?7!7%*@$%@)

B*3![G

F"O$&

25. >?@-)%./,(0.,ABBC2D5F?"#QFO-O,%;/:;/D<2H9#02Z#6-^72&

-:=29589 )(*<M,MND1?7!7%*@$B*3![G%#$"%('9@+-(9!=@$0&G@$'3CD,

*/??(D!'X?123CPCF9,

26. -0./,A0=>?@(29?"#QFO-O,%;/ >H@-DSFH=2(!2D15OG":;/-$_9

Z3H&,./9R -?=9 )3E$H9;FD%&#2\ -H%;6W D"WQ!

D%%AD%O5#-3SF 'D%T H%.,15OG":;/-$_9Z3H&+92#-3SD,./9R

:;/'202%G-?./,0O=,+581H9V/(D5F,;D+581H9V/(A#@ )(*2/D-&'*

8/A-1?7!7%*@$%('G;(<F,*,%"'/DF*#%!).DCPCF9,

27. >9D%N;:;/>?@(29A0=

GTDO@,( ,2!0;+,(-H31AH3,,D!2D

QFO-O,%;/ >H@H3;D-3;/6(D2%'50M5' H2D'50M5'Z#9+,(

-H31Z#6A0=O58(>! >H@3@2(,,D#@1698<2 H2D+,(-H31

D%&-#S9-+@2O2 >H@%;FA$7FQ7:6* 8%&!F2-G@$CF2%%)'()

1?7!7%*@$%('G;(<F,S.-F"/&*3+(0!+#%&F*#%CF9,

D2%F%ED2%

28. 9<2-)%./,(0.,ABBC2-+@2%5FF%ED2%!2D?=2(J=,0

:;/M=29D2%

%5F%,(Z#6>?@,&AH3=QFF-#;61D59-:=29589 !4*(3'3G;(<F,

)(*<M,!+*#$%&9#%CPPQ(9@+-(9B2%D[/0

29.

.JEB1%E%#-!"#3(4("#<(?#A9/)'/&D(3/4?#A$./=D2(

'C.?AFK$LAE-

30. #TQ30.,!5F>H@QH@( '&,2# Q3&A0=0;98<2059Q3&!2%&F;

-$[`,9

GEB088-1

3()*45#6<")63>)$?&#<C1D!#:

=!3>:=EEF)7//=0"G)D

1. >?@0.,!5F-'%E0 G@20;02D5F-)%./,( )(*=:I!=@0+-(9+-?+N9

%('G;(<F,!).D)(*?(D!'X?

2. G.,-)%./,(0.,ABBC2F%E-1N0.,!5F:;/-$_9^919+N&:<2(29:;/

-)%./,(0.,O5#,2!'50M5'D5F'26AB:;/J=,9,6T= !+*#$%&9#%7/DG@$

=/9S/=)/?=(0CPG@$ "9@)*31=CPPQ(CF2S6("# %('G`<F,=6-"G@$

!B]"E2F38%&!+*#$%&9#%CPPQ(G@$C969@>"-"FN,9 "9@)*31=CPPQ(

CF2S6("# 123G;(<F,S:,Ba.?/7.&("V:)CPPQ(MX

%7CD ,

3. G.,-)%./,(0.,ABBC2F%E-1N0.,!5F:;/-$_9^919+N&:<2(29:;/

'26%5#,2!'50M5'D5F'26AB:;/J=,9,6T= =(0*/DG@$=/9S/=)/?

=(0CPG@$ "9@)*31=CPPQ(CF2S6("# %('G;(<F,=6-"G @$!B]"E2F3

8%&!+*#$%&9#%CPPQ(G@$C969@>"-"FN,9 "9@)*31=CPPQ(CF2S6("#

123G;(<F,S:,Ba.?/7.&("V:)CPPQ(MX%7CD,

4. O%1!',FF%E-1N:;/6.9>H@0;)1200 5/9)(-'0,H2D>? @(29

-)%./,(0.,>97.89:;/'T( %&15(,6=2>H@0;)9,6

T=# @293=2(

5. !5F-)%./,(0.,>H@Q9=9

6. %&15(,6=2>H@0.,'50M5'D5F?E89'=19:;/H0"9A#@

7. ,6=2$3=,6>H@-)%./,(0.,:<2(29)@2(A1@ >?@(29-)% ./,(0.,>9

+N&:;/G.,,6T=-:=29589

9+#-L1-M1L?1B*'?L,)#(9A&'GE7(8#(61(6=6=D6"#8#($LA>N

$(&D'8N#?*'?L,)#(9A&'GE7(8#('#N-=!,#-A+'(L:83/4

/,?ME,9(18O'8!CF;*+

9. 15'#"F2(,6=2(,2!0;'2%-)0;:;/-$_97E\ %&15(,6= 2' T##0K"L9

H%.,>H@'2%-H3=29589'50M5'D5F%=2(D26 $aEF5OEO20+@,0T3

#@29)120$3,#456+,(MT@M3EO15'#"

/168H-3()76,6()*;&I)6J9

)<2-O.,9:

,6=2>H@)120A0=%&05#%&15(H%.,)120)"@9-)6D5FM3EO45Nb*

(!2DD2%>?@(29J8<2H326)%58() ,6T=-H9.,D2%$aEF5O EO20

Dc-DNb*#@29)120$3,#456>9D2%>?@(29M3EO45Nb*,6=2(

-)%=()%5# D2%>?@(29,6=2(A0=-H02&'0H%.,D2%A0=$aEF5OEO20

Dc-DNb*#@29)120$3,#456>9)T=0.,>?@(299;8,2!D =,>H@-DE#

D2%F2#-!SF,6=2(%"9Q%(

ENC007-7

3()76,6()<")63>)$?&#<C1D8JKG()31L

G();01/4&1/7/4*4#0JK

1. D=,9>?@(29O35FQFO-O,%;/ >H @,=29)<2Q9&9<2Q3&-)% ./,(

H026-O.,9:58(H0#F9 (1) -)%./,(?2%*!QFO-O,%;/

(2) QFO-O,%;/Q3& (3) O51M3EO45Nb*:;/>?@QFO-O,%;/

2. H@20G,#Q6D' =19O3 5FQFO-O,%;/

3. H2D%&6&-132>9D2%>?@(29'589-DE9A$ >H@H6"#>?@(29:59:;

-9./,(!2D,2!0;)120-';/6(:;/!&%@,9!5# AH0@H%.,%&-FE#A#@

4. H2D'2%3&326,E-3SDZ:%A3O*D%&-#S9-+@2O2 >H@3@2(,,D

#@1698<2-$3=2Q3&%;FA$7FQ7:6*:59:; -9./,(!2D,2!:<2

>H@O2F,#

5. H@2035#1(!%O35FQFO-O,%;/:

(1)

H@20QO&+581D5F15OG":;/-$_9'./,9<2ABBC2>#R

(2) H3;D-3;/6(D2%-DSFO35FQFO-O,%;/A1@>942?9&%=10

D5F15OG":;/-$_9Z3H& -?=9 D%%AD%O5#-3SF

-H%;6W ]3]

(3) ,6=2>H@O35FQFO-O,%;/GTD98<2H%.,K9

QFO-O,%;/35#1(!%,2!:<2>H@-DE#D2%AH3+,(D%&Q'

ABBC2 %@,9!5# AH0@H%.,-';6H26A#@

6. H@20-DSF-)%./,(0.,Q3&O35FQFO-O,%;/A1@>9'G29:;/0;

,"NH4T0E'T(GV(H%.,-DE9 50°C

7. H@20-M2:E8(O35FQFO-O,%;/ Q0@1=2QFO-O,%;/!&H0#H%.,

-';6H26!9>?@D2%A0=A#@,

;D O35FQFO-O,%;/,2!%&-FE#>9

D,(AB

8. %&15(,6=2:<2QFO-O,% ;/ODH3=9H%.,D%&:FD%&Q:D

9. H@20>?@QFO-O,% ;/:;/-';6H26

Page is loading ...

Makita BDF343 User manual

Brand: Makita

Model: BDF343

Category: Power drills

Type: User manual

This manual is also suitable for

BDF453

Download PDF

report

Makita BDF343 User manual

This manual is also suitable for

Makita BDF343 User manual

Related papers

Other documents