Makita XT283X1 User manual

Brand: Makita

Model: XT283X1

Category: Power tools

Type: User manual

INSTRUCTION MANUAL

MANUAL DE INSTRUCCIONES

Cordless Impact Driver

Atornillador de Impacto

Inalámbrico

XDT13

IMPORTANT: Read Before Using.

IMPORTANTE: Lea antes de usar.

2 ENGLISH

ENGLISH (Original instructions)

SPECIFICATIONS

Model: XDT13

Fastening capacities Machine screw 4 mm - 8 mm (5/32" - 5/16")

Standard bolt 5 mm - 16 mm (3/16" - 5/8")

High tensile bolt 5 mm - 14 mm (3/16" - 9/16")

No load speed (RPM) 0 - 3,400 /min

Impacts per minute 0 - 3,600 /min

Overall length 126 mm (5")

Rated voltage D.C. 18 V

Standard battery cartridge BL1815N, BL1820B BL1830, BL1830B, BL1840B,

BL1850B, BL1860B

Net weight 1.3 kg (2.8 lbs) 1.5 kg (3.3 lbs)

• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange

without notice.

• Specicationsandbatterycartridgemaydifferfromcountrytocountry.

• Weight,withbatterycartridge,accordingtoEPTA-Procedure01/2003

SAFETY WARNINGS

General power tool safety warnings

WARNING: Read all safety warnings and

all instructions. Failure to follow the warnings and

instructionsmayresultinelectricshock,reand/or

seriousinjury.

Save all warnings and instruc-

tions for future reference.

Theterm"powertool"inthewarningsreferstoyour

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

1. Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

2. Do not operate power tools in explosive atmo-

spheres, such as in the presence of ammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

3. Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

Electrical Safety

1. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiedplugsandmatchingoutletswill

reduce risk of electric shock.

2. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators.Thereisanincreasedriskofelec-

tric shock if your body is earthed or grounded.

3. Do not expose power tools to rain or wet con-

ditions.Waterenteringapowertoolwillincrease

the risk of electric shock.

4. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords

increase the risk of electric shock.

5. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electric shock.

6. If operating a power tool in a damp location is

unavoidable, use a ground fault circuit inter-

rupter (GFCI) protected supply. Use of a GFCI

reduces the risk of electric shock.

Personal Safety

1. Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the inuence of drugs, alcohol or med-

ication.Amomentofinattentionwhileoperating

powertoolsmayresultinseriouspersonalinjury.

2. Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

willreducepersonalinjuries.

3. Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools with

yourngerontheswitchorenergisingpowertools

that have the switch on invites accidents.

4. Remove any adjusting key or wrench before

turning the power tool on.Awrenchorakeyleft

attached to a rotating part of the power tool may

resultinpersonalinjury.

3 ENGLISH

5. Do not overreach. Keep proper footing and

balance at all times.Thisenablesbettercontrol

of the power tool in unexpected situations.

6. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing, and gloves

away from moving parts.Looseclothes,jewel-

lery or long hair can be caught in moving parts.

7. If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

dust collection can reduce dust-related hazards.

Power tool use and care

1. Do not force the power tool. Use the correct

power tool for your application.Thecorrect

powertoolwilldothejobbetterandsaferatthe

rate for which it was designed.

Do not use the power tool if the switch does not turn

it on and off.Anypowertoolthatcannotbecontrolled

with the switch is dangerous and must be repaired.

Disconnect the plug from the power source and/or

the battery pack from the power tool before making

any adjustments, changing accessories, or storing

power tools. Such preventive safety measures reduce

the risk of starting the power tool accidentally.

4. Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in the

hands of untrained users.

5. Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the

power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

6. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

7. Use the power tool, accessories and tool bits

etc. in accordance with these instructions, tak-

ing into account the working conditions and

the work to be performed. Use of the power tool

for operations different from those intended could

result in a hazardous situation.

Battery tool use and care

1. Recharge only with the charger specied by

the manufacturer.Achargerthatissuitablefor

onetypeofbatterypackmaycreateariskofre

when used with another battery pack.

2. Use power tools only with specically desig-

nated battery packs. Use of any other battery

packsmaycreateariskofinjuryandre.

3. When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another. Shorting the battery termi-

nalstogethermaycauseburnsorare.

4. Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If con-

tact accidentally occurs, ush with water. If

liquid contacts eyes, additionally seek medical

help.Liquidejectedfromthebatterymaycause

irritation or burns.

Service

1. Have your power tool serviced by a qualied

repair person using only identical replacement

parts.Thiswillensurethatthesafetyofthepower

tool is maintained.

2. Follow instruction for lubricating and chang-

ing accessories.

3. Keep handles dry, clean and free from oil and

grease.

Cordless impact driver safety

warnings

1. Hold power tool by insulated gripping sur-

faces, when performing an operation where

the fastener may contact hidden wiring.

Fasteners contacting a "live" wire may make

exposed metal parts of the power tool "live" and

could give the operator an electric shock.

2. Always be sure you have a rm footing.

Be sure no one is below when using the tool in

high locations.

3. Hold the tool rmly.

4. Wear ear protectors.

5. Do not touch the bit or the workpiece immedi-

ately after operation. They may be extremely

hot and could burn your skin.

6. Keep hands away from rotating parts.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product.

MISUSE or failure to follow the safety rules stated

in this instruction manual may cause serious

personal injury.

Symbols

Thefollowingsshowthesymbolsusedfortool.

volts

direct current

no load speed

revolutions or reciprocation per minute

number of blow

Important safety instructions for

battery cartridge

1. Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using

battery.

2. Do not disassemble battery cartridge.

4 ENGLISH

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

If electrolyte gets into your eyes, rinse them out

with clear water and seek medical attention right

away. It may result in loss of your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any con-

ductive material.

(2) Avoid storing battery cartridge in a con-

tainer with other metal objects such as

nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.

A battery short can cause a large current

ow, overheating, possible burns and even a

breakdown.

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a re.

8. Be careful not to drop or strike battery.

9. Do not use a damaged battery.

10.

The contained lithium-ion batteries are subject to

the Dangerous Goods Legislation requirements.

For commercial transports e.g. by third parties,

forwarding agents, special requirement on pack-

aging and labeling must be observed.

For preparation of the item being shipped, consult-

ing an expert for hazardous material is required.

Please also observe possibly more detailed

national regulations.

Tapeormaskoffopencontactsandpackupthe

battery in such a manner that it cannot move

around in the packaging.

11. Follow your local regulations relating to dis-

posal of battery.

SAVE THESE INSTRUCTIONS.

CAUTION: Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that

have been altered, may result in the battery bursting

causingres,personalinjuryanddamage.Itwill

also void the Makita warranty for the Makita tool and

charger.

Tips for maintaining maximum

battery life

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice

less tool power.

2. Never recharge a fully charged battery car-

tridge. Overcharging shortens the battery

service life.

Charge the battery cartridge with room tempera-

ture at 10 °C - 40 °C (50 °F - 104 °F). Let a hot

battery cartridge cool down before charging it.

4. Charge the battery cartridge if you do not use

it for a long period (more than six months).

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before adjusting or checking function on the tool.

Installing or removing battery

cartridge

CAUTION: Always switch off the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge. Failure to hold the tool and the battery

cartridgermlymaycausethemtoslipoffyourhands

and result in damage to the tool and battery cartridge

andapersonalinjury.

►1. Red indicator 2. Button 3. Battery cartridge

Toremovethebatterycartridge,slideitfromthetool

while sliding the button on the front of the cartridge.

Toinstallthebatterycartridge,alignthetongueonthe

battery cartridge with the groove in the housing and slip

it into place. Insert it all the way until it locks in place

with a little click. If you can see the red indicator on the

upper side of the button, it is not locked completely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen. If not,

itmayaccidentallyfalloutofthetool,causinginjuryto

you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly. If the cartridge does not slide in easily, it is

not being inserted correctly.

5 ENGLISH

Indicating the remaining battery

capacity

Only for battery cartridges with "B" at the end of the

model number

►1. Indicator lamps 2. Check button

Press the check button on the battery cartridge to indi-

catetheremainingbatterycapacity.Theindicatorlamps

light up for few seconds.

Indicator lamps Remaining

capacity

Lighted Off Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

Thebattery

may have

malfunctioned.

NOTE: Depending on the conditions of use and the

ambient temperature, the indication may differ slightly

from the actual capacity.

Tool / battery protection system

Thetoolisequippedwithatool/batteryprotectionsys-

tem.Thissystemautomaticallycutsoffpowertothe

motortoextendtoolandbatterylife.Thetoolwillauto-

matically stop during operation if the tool or battery is

placed under one of the following conditions:

Overload protection

Whenthebatteryisoperatedinamannerthatcauses

it to draw an abnormally high current, the tool automat-

ically stops without any indication. In this situation, turn

the tool off and stop the application that caused the tool

tobecomeoverloaded.Thenturnthetoolontorestart.

Overheat protection

Whenthetool/batteryisoverheated,thetoolstops

automatically. In this situation, let the battery cool

before turning the tool on again.

Overdischarge protection

Whenthebatterycapacityisnotenough,thetoolstops

automatically. In this case, remove the battery from the

tool and charge the battery.

NOTE: Overload protection will work only with batter-

ies with star marking.

►1. Star marking

Switch action

►1. Switch trigger

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

Tostartthetool,simplypulltheswitchtrigger.Tool

speed is increased by increasing pressure on the switch

trigger. Release the switch trigger to stop.

Electric brake

Thistoolisequippedwithanelectricbrake.Ifthetool

consistently fails to quickly stop after the switch trigger

is released, have the tool serviced at a Makita service

center.

6 ENGLISH

Lighting up the front lamp

►1. Lamp

CAUTION: Do not look in the light or see the

source of light directly.

Pulltheswitchtriggertolightupthelamp.Thelamp

keeps on lighting while the switch trigger is being pulled.

Thelampgoesoutapproximately10secondsafter

releasing the switch trigger.

NOTE: Use a dry cloth to wipe the dirt off the lens of

the lamp. Be careful not to scratch the lens of lamp, or

it may lower the illumination.

Reversing switch action

►1. Reversing switch lever

CAUTION: Always check the direction of

rotation before operation.

CAUTION: Use the reversing switch only after

the tool comes to a complete stop. Changing the

direction of rotation before the tool stops may dam-

age the tool.

CAUTION: When not operating the tool,

always set the reversing switch lever to the neu-

tral position.

Thistoolhasareversingswitchtochangethedirection

of rotation. Depress the reversing switch lever from the

AsideforclockwiserotationorfromtheBsideforcoun-

terclockwise rotation.

Whenthereversingswitchleverisintheneutralposi-

tion, the switch trigger cannot be pulled.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Installing or removing driver bit/

socket bit

12 mm

(15/32”)

9 mm

(3/8”)

Useonlythedriverbit/socketbitshowninthegure.Do

not use any other driver bit/socket bit.

►1. Driver bit 2. Sleeve

Toinstallthedriverbit,insertitintothesleeveasfaras

it will go.

►1. Driver bit 2. Sleeve

Toremovethedriverbit,pullthesleeveinthedirection

of the arrow and pull the driver bit out.

7 ENGLISH

NOTE: If the driver bit is not inserted deep enough

into the sleeve, the sleeve will not return to its original

position and the driver bit will not be secured. In this

case, try re-inserting the bit according to the instruc-

tions above.

NOTE:Whenitisdifculttoinsertthedriverbit,pull

the sleeve and insert it into the sleeve as far as it will

go.

NOTE:Afterinsertingthedriverbit,makesurethatit

isrmlysecured.Ifitcomesout,donotuseit.

Installing hook

►1. Groove 2. Hook 3. Screw

Thehookisconvenientfortemporarilyhangingthetool.

Thiscanbeinstalledoneithersideofthetool.Toinstall

the hook, insert it into a groove in the tool housing on

eithersideandthensecureitwithascrew.Toremove,

loosen the screw and then take it out.

OPERATION

Theproperfasteningtorquemaydifferdependingupon

the kind or size of the screw/bolt, the material of the

workpiecetobefastened,etc.Therelationbetweenfas-

teningtorqueandfasteningtimeisshowninthegures.

Proper fastening torque for standard bolt

140

(103)

120

(89)

100

(74)

(59)

(44)

(30)

(15)

M16(5/8")

M10(3/8")

M8(5/16")

M14(9/16")

M12(1/2")

2.01.0

M16(5/8")

M14(9/16")

M12(1/2")

M10(3/8")

M8(5/16")

N•m

(ft•lbs)

►1. Fastening time (second) 2. Fastening torque

Proper fastening torque for high tensile bolt

200

(148)

180

(133)

160

(118)

140

(103)

120

(89)

100

(74)

(59)

(44)

(30)

(15)

M14(9/16")

M12(1/2")

M10(3/8")

M8(5/16")

2.0 3.01.0

N•m

(ft•lbs)

M14(9/16")

M12(1/2")

M10(3/8")

M8(5/16")

►1. Fastening time (second) 2. Fastening torque

Holdthetoolrmlyandplacethepointofthedriverbit

inthescrewhead.Applyforwardpressuretothetoolto

the extent that the bit will not slip off the screw and turn

the tool on to start operation.

8 ENGLISH

NOTICE: If you use a spare battery to continue

the operation, rest the tool at least 15 min.

NOTE: Use the proper bit for the head of the screw/

bolt that you wish to use.

NOTE:WhenfasteningM8orsmallerscrew,carefully

adjustpressureontheswitchtriggersothatthescrew

is not damaged.

NOTE: Hold the tool pointed straight at the screw.

NOTE: If the impact force is too strong or you tighten

thescrewforatimelongerthanshowninthegures,

the screw or the point of the driver bit may be over-

stressed, stripped, damaged, etc. Before starting your

job,alwaysperformatestoperationtodeterminethe

proper fastening time for your screw.

Thefasteningtorqueisaffectedbyawidevarietyof

factorsincludingthefollowing.Afterfastening,always

check the torque with a torque wrench.

1. Whenthebatterycartridgeisdischargedalmost

completely, voltage will drop and the fastening

torque will be reduced.

2. Driver bit or socket bit

Failure to use the correct size driver bit or socket

bit will cause a reduction in the fastening torque.

3. Bolt

• Eventhoughthetorquecoefcientandthe

class of bolt are the same, the proper fasten-

ing torque will differ according to the diame-

ter of bolt.

• Eventhoughthediametersofboltsarethe

same, the proper fastening torque will differ

accordingtothetorquecoefcient,theclass

of bolt and the bolt length.

4. Themannerofholdingthetoolorthematerial

of driving position to be fastened will affect the

torque.

5. Operating the tool at low speed will cause a reduc-

tion in the fastening torque.

MAINTENANCE

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before attempting to perform inspection or

maintenance.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

TomaintainproductSAFETYandRELIABILITY,

repairs,anyothermaintenanceoradjustmentshould

beperformedbyMakitaAuthorizedorFactoryService

Centers, always using Makita replacement parts.

OPTIONAL

ACCESSORIES

CAUTION: These accessories or attachments

are recommended for use with your Makita tool

specied in this manual.Theuseofanyother

accessories or attachments might present a risk of

injurytopersons.Onlyuseaccessoryorattachment

for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Driverbits

• Socketbits

• Hook

• Plasticcarryingcase

• Batteryprotector

• Toolhanger

• Makitagenuinebatteryandcharger

NOTE: Some items in the list may be included in the

toolpackageasstandardaccessories.Theymay

differ from country to country.

MAKITA LIMITED ONE YEAR

WARRANTY

Warranty Policy

EveryMakitatoolisthoroughlyinspectedandtested

before leaving the factory. It is warranted to be free of

defects from workmanship and materials for the period

ofONEYEARfromthedateoforiginalpurchase.

Should any trouble develop during this one year period,

returntheCOMPLETEtool,freightprepaid,toone

ofMakita’sFactoryorAuthorizedServiceCenters.If

inspection shows the trouble is caused by defective

workmanship or material, Makita will repair (or at our

option, replace) without charge.

ThisWarrantydoesnotapplywhere:

• repairshavebeenmadeorattemptedbyothers:

• repairsarerequiredbecauseofnormalwearand

tear:

• thetoolhasbeenabused,misusedorimproperly

maintained:

• alterationshavebeenmadetothetool.

INNOEVENTSHALLMAKITABELIABLEFORANY

INDIRECT,INCIDENTALORCONSEQUENTIAL

DAMAGESFROMTHESALEORUSEOFTHE

PRODUCT.THISDISCLAIMERAPPLIESBOTH

DURINGANDAFTERTHETERMOFTHISWARRANTY.

MAKITADISCLAIMSLIABILITYFORANYIMPLIED

WARRANTIES,INCLUDINGIMPLIEDWARRANTIES

OF"MERCHANTABILITY"AND"FITNESSFORA

SPECIFICPURPOSE,"AFTERTHEONEYEARTERM

OFTHISWARRANTY.

ThisWarrantygivesyouspeciclegalrights,andyou

may also have other rights which vary from state to state.

Some states do not allow the exclusion or limitation of

incidental or consequential damages, so the above lim

itation or exclusion may not apply to you. Some states do

not allow limitation on how long an implied warranty lasts,

so the above limitation may not apply to you.

Page is loading ...

Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to the State of California

to cause cancer, birth defects or other reproductive harm. Some examples

of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this

type of work. To reduce your exposure to these chemicals: work in a well

ventilated area, and work with approved safety equipment, such as those

dust masks that are specially designed to filter out microscopic particles.

WARNING

< USA only >

ADVERTENCIA

Algunos polvos creados por el lijado, aserrado, esmerilado, taladrado y

otras actividades de la construcción contienen sustancias químicas

reconocidas por el Estado de California como causantes de cáncer, defectos

de nacimiento y otros peligros de reproducción. Algunos ejemplos de estos

productos químicos son:

• plomo de pinturas a base de plomo,

• sílice cristalino de ladrillos y cemento y otros productos de albañilería, y

• arsénico y cromo de maderas tratadas químicamente.

El riesgo al que se expone varía, dependiendo de la frecuencia con la que

realice este tipo de trabajo. Para reducir la exposición a estos productos

químicos: trabaje en un área bien ventilada y póngase el equipo de seguridad

indicado, tal como las máscaras contra polvo que están especialmente

diseñadas para filtrar partículas microscópicas.

< Sólo en los Estados Unidos >

Makita Corporation

3-11-8, Sumiyoshi-cho,

Anjo, Aichi 446-8502 Japan

www.makita.com

885505-946

XDT13-1

EN,ESMX

20160303

Makita XT283X1 User manual

Brand: Makita

Model: XT283X1

Category: Power tools

Type: User manual

Download PDF

report

in other languages

español: Makita XT283X1 Manual de usuario

Makita XT283X1 User manual

Makita XT283X1 User manual

in other languages

Related papers

Other documents