Braun 5441 User manual

Page is loading ...

13

14

15

16

17

18

19

12

Flex integral 5441

10

1

A

2

3

5

6

7

8

9

4

11

B

Clean &Charge

on

off

trimmer

head lock

lock

No. 6000

KURTZ DESIGN 21.01.01

5485458_S.3.fm Seite 1 Dienstag, 22. Januar 2002 10:23 10

4

English

IMPORTANT SAFETY

INSTRUCTIONS

When using an electrical appliance, basic precautions should always be

followed, including the following:

Read all instructions before using this appliance.

DANGER

To reduce the risk of electric shock:

1. Do not reach for an appliance that has fallen into water.

Unplug immediately.

2. Do not use while bathing or in a shower.

3. Do not place, store or charge the appliance where it can fall or be pulled

into a tub or sink. Do not place in or drop into water or other liquid.

4. When not using for a longer period of time, unplug this appliance from the

electrical outlet.

5. Unplug this appliance before cleaning.

6. This appliance is provided with a low voltage adapter. Do not exchange or

manipulate any part of it.

FOR HOUSEHOLD USE

SAVE THESE INSTRUCTIONS

5485458_S.4-38.fm Seite 4 Dienstag, 22. Januar 2002 10:22 10

5

WARNING

To reduce the risk of burns, ﬁre, electric shock, or injury to persons:

1. Close supervision is necessary when this appliance is used by, on, or near

children.

2. Use this appliance only for its intended use as described in this manual.

Do not use attachments not recommended by the manufacturer.

3. The appliance should never be exposed to temperatures of less than

32 ºF / 0 ºC and more than 105 ºF/+40ºC for longer than a few hours.

Keep the appliance and cord dry at all times. Do not handle with wet hands.

Do not store in a damp environment. To avoid damage do not wind the

cord around the appliance. It is important to check the cord for damage

periodically particularly at each end where the cord enters the plug.

4. Never operate this appliance if it has a damaged cord or plug, if it is not

working properly, if it has been dropped or damaged, or dropped into water.

Return the appliance to a service center for examination and repair.

5. Keep the cord away from heated surfaces.

6. Never drop or insert any object into any opening.

7. Do not use outdoors or operate where aerosol (spray) products are being

used or where

oxygen is being administered.

8. Do not use this appliance with a damaged or broken foil, as serious facial

injuries may occur.

9. Always attach plug to appliance ﬁrst, then to outlet.

To disconnect, turn all controls to «off», then remove plug from outlet.

5485458_S.4-38.fm Seite 5 Dienstag, 22. Januar 2002 10:22 10

6

A Shaver

Your Braun Flex Integral is supplied with a Braun

Clean&Charge (please see section B).

Technical speciﬁcations

•Wattage via cord set: 7 W

• Automatic power supply: (100-240 V~/ 50 or 60 Hz)

• Shaver input voltage: 12 V

Description

1 Foil protection cap

2 Shaver foil

3 Cutter block

4 Foil release button

5 Pop-out long hair trimmer

6 Switch lock

7 Switch for locking the pivoting head («head lock»)

and for activating the pop-out long hair trimmer

(«trimmer»)

8 On/off switch

9 Charging light

10 Shaver socket

11 Power supply cord set

Charging the shaver

• First

charging: Using the power supply cord set,

connect the shaver to the mains with the switch

on position «off» and charge it for at least 4 hours

(plug might get warm).

• Once the shaver is completely charged, shave with-

out the cord until fully discharged. Then recharge to

full capacity again (subsequent charges will take

about 1 hour).

•A full charge will give up to 50 minutes of cordless

shaving time depending on your beard growth.

However, the maximum battery capacity will only be

reached after several charging/discharging cycles.

• Best environmental temperature range for charging

is 60 °F to 95°F / 15 °C to 35 °C.

• The charging light shows that the shaver is being

charged. When the rechargeable batteries are fully

charged, the charging light goes off.

If later on, the charging light comes on again, this

indicates that the shaver is being recharged to

maintain its full capacity.

7570

off

on

5485458_S.4-38.fm Seite 6 Dienstag, 22. Januar 2002 10:22 10

7

Shaving

Switch lock

The shaver is delivered with the switch lock activated

(position «lock»). Push the switch lock up before you

shave for the ﬁrst time. To avoid accidentally switching

the shaver on, e.g. when travelling, push the switch lock

to position «lock».

Switch positions

off

on

Shaving with the pivoting head. The pivot-

ing cutting system automatically adjusts

to every contour of your face.

head lock

Shaving with the pivoting head locked

(to permit shaving in difﬁcult areas, e.g.

under the nose)

trimmer

The long hair trimmer is activated

(for trimming sideburns, moustache and

beard).

Shaving with the cord

If the rechargeable batteries are discharged, you may

also shave with the shaver connected to the mains via

the power supply cord set.

(If the shaver does not run immediately, charge it with

the switch on position «off» for approx. 1 minute.)

Tips for the perfect shave

• It can take 14-21 days for your beard to adjust to

the new shaving system.

•We recommend that you shave befor

e washing,

as the skin tends to be slightly swollen after

washing.

• Hold the shaver at right angles (90°) to the skin.

• Stretch your skin and shave against the direction

of beard growth.

• Replace the shaver foil and cutter block every

18 months, or when the parts are worn, to ensure

optimum shaving performance.

off

on

trim

head lock

off on

trimmer

head lock

lock

5485458_S.4-38.fm Seite 7 Dienstag, 22. Januar 2002 10:22 10

8

Keeping your shaver in top shape

Automated cleaning

The Braun Clean&Charge automatically takes care of all

cleaning and lubrication needs of your shaver. Please

refer to section B.

Manual cleaning

For easy manual cleaning after each shave, switch the

shaver off. Press the release button, take off the shaver

foil and gently tap it out on a ﬂat surface.

Using the brush, clean the cutter block and the inner

area of the pivoting head. About every four weeks,

clean the cutter block with Braun cleaning agents.

If your skin is very dry and you notice a reduced

operation time of the shaver, apply a drop of light

machine oil onto the shaver foil.

Do not rinse the shaver in or under water.

Replacing the shaving parts

The shaver foil and cutter block are precision parts that,

in time, are subject to wear. Replace your foil and cutter

block every 18 months and get a 25 % better shave.*

(Shaver foil and cutter block: part no. 6000)

(* Overall evaluation from Braun users comparing their

shave with new parts and those used for 18 months.)

oil

5485458_S.4-38.fm Seite 8 Dienstag, 22. Januar 2002 10:22 10

9

Preserving the cell unit

In order to maintain the optimum capacity of the

rechargeable batteries, the shaver has to be fully

discharged (by shaving) every 6 months approximately.

Then recharge the shaver to full capacity again. This

reconditions the rechargeable batteries.

Accessories

Available at your dealer or Braun Service Centers:

Shaver foil and cutter block

(part no. 6000)

Environmental notice

This appliance is provided with a nickel-hydride bat-

teries. They do not contain any harmful heavy metals.

Nevertheless, in the interest of recycling raw materials,

please do not dispose of this appliance in the

household waste at the end of its useful life. Disposal

can take place at a Braun Service Center or appropriate

collection sites.

Subject to change without notice.

6000

Flex Integral

5485458_S.4-38.fm Seite 9 Dienstag, 22. Januar 2002 10:22 10

10

B Clean&Charge

Braun Clean&Charge has been developed for cleaning,

charging and storing your shaver. Clean your shaver

daily in the Clean&Charge.

During the automated cleaning process, the shaver is

switched on and off at intervals to obtain best cleaning

results. Since the specially formulated cleaning ﬂuid

contains a small amount of oil, the cleaning procedure

also fulﬁlls the lubrication needs of the shaver.

Important

• Only use the power supply cord set supplied with

the shaver.

• In order to avoid any leakage of the cleaning ﬂuid,

place the appliance on a ﬂat, stable surface. Do

not tip, move suddenly or transport in any way if a

cleaning cartridge is installed.

• Do not place the appliance in a mirror cabinet, nor

store it over radiators, nor place it on polished or

laquered surfaces. Do not expose to direct sunlight.

• The appliance contains highly ﬂammable

liquid. Keep it away from sources of ignition.

No smoking. Keep out of reach of children. Do not

reﬁll cartridge. Use only original Braun reﬁll

cartridge.

• When cleaning the shaver, its protection cap should

be removed.

Description

12 Lift button for cartridge exchange

13 Contact bow

14 Release button

15 Operation mode selector

16 «clean» light: cleaning process indicator

17 «charge» light: charging process indicator

18 «cartridge» light: cartridge replacement indicator

19 Cleaning cartridge

Technical speciﬁcations

• Power consumption:

•3 W when cleaning

•7 W when charging

• Power supply: 100 -240 V ~ / 50 or 60 Hz

(automatic adaptation)

• Input voltage: 12 V

5485458_S.4-38.fm Seite 10 Dienstag, 22. Januar 2002 10:22 10

11

Before using Clean&Charge

First charge:

For the ﬁ

rst charge of the shaver, connect the power

supply cord set directly to the shaver, charge it for

4 hours and shave at least once.

Only then can the shaver be cleaned or recharged in the

Clean&Charge.

If the rechargeable batteries are discharged, select the

combined «clean» + «charge» programme rather than

the «clean» programme alone.

Installing the cartridge

Press the lift button (12) to open the housing.

Hold the cartridge down on a ﬂat, stable surface

(e.g. table). Carefully remove the lid from the cartridge.

Slide the cartridge into the base as far as it will go.

Slowly close the housing by pushing it down until it

locks.

Replacing the cartridge

After having pressed the lift button to open the housing,

wait for a few seconds before removing the used car-

tridge.

Before discarding the used cartridge, make sure to

close the openings using the lid of the new cartridge,

since the used cartridge will contain contaminated

cleaning solution.

Operating your Clean&Charge

• Use the power supply cord set from your shaver and

plug it into the Clean&Charge and then into a main

outlet.

Open the contact bow (13) by pressing the release

button (14). After shaving, switch the shaver off and

place it upside down into the Clean&Charge. The

pivoting head must not be locked (switch «head

lock» position down)

• Select the operation mode by toggling with the

mode selector (15):

clean (about 15 min)

clean + charge (about 75 min)

charge (about 60 min)

The corresponding lights will come on.

7570

2

1

new

old

new

5441

on

/o

ff

clean

charge

5441

5485458_S.4-38.fm Seite 11 Dienstag, 22. Januar 2002 10:22 10

12

• Slide down the contact bow to connect the shaver

and to start the selected program.

If no program is selected, the default function

«clean» will be started.

• Do not interrupt a running program, as it leaves the

shaver wet and not ﬁt for use. If interruption is need-

ed nonetheless, press the release button.

• After a program has ﬁnished, the corresponding light

will go out. If later on, and when in charging mode,

the charging light of the shaver comes on again. This

indicates that the shaver is being recharged to

maintain its full capacity. Prior to the next shave,

press the release button to release the shaver.

• When the «cartridge» light starts ﬂashing, the

remaining ﬂuid in the cartridge is sufﬁcient for ap-

proximately 5 more cleaning cycles. After these

5 cycles, the cleaning performance will be reduced

and the car-tridge has to be replaced.

• When the «cartridge» light illuminates constantly, the

cleaning function is locked and a new cartridge has

to be installed. Only then, the next cleaning cycle

can be started.

•A cleaning cartridge should be sufﬁcient for about

30 cleaning cycles. With daily use, the cleaning car-

tridge should be replaced approx. every 4 weeks.

• The hygienic cleaning solution cartridge contains

alcohol which, once opened, will naturally evaporate

slowly into the surrounding air. Each cartridge, if not

used daily, should be replaced after approximately

8 weeks.

Clean the housing from time to time with a damp cloth,

especially the opening where the shaver rests.

Accessories

Available at your dealer or Braun Service Centers:

Reﬁll cartridge

(double pack) CCR 2, (#5331)

Subject to change without notice.

select

5441

s

ele

ct

5441

5485458_S.4-38.fm Seite 12 Dienstag, 22. Januar 2002 10:22 10

13

FOR USA ONLY

2 year limited warranty

(foil and cutterblock excluded)

Braun warrants this Braun appliance (except foil and cutterblock) to be free of

defects in material and workmanship for a period of two years from the date of

original purchase.

If the appliance exhibits such a defect, Braun will, at its option, either repair or

replace it for the consumer without charge, provided the consumer:

1. Returns the appliance, postage paid and insured, indicating the reasons for

returning it to: Shaver Service Department, Braun U.S. Div., The Gillette Co.,

400 Unicorn Park Drive, Woburn,

MA 01801-3376,

or one of its authorized

service centers.

2. Submits proof of date of original purchase.

This warranty does not cover foils, cutterblocks or damage resulting from

accident, misuse, abuse, dirt, water, tampering, unreasonable use, normal wear,

servicing performed or attempted by unauthorized service agencies or failure to

provide reasonable and necessary maintenance, including recharging.

ALL IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF

MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE, ARE

LIMITED IN DURATION TO 2 YEARS FROM DATE OF ORIGINAL PURCHASE.

IN NO EVENT WILL BRAUN BE RESPONSIBLE FOR CONSEQUENTIAL

DAMAGES RESULTING FROM THE USE OF THIS PRODUCT.

Some states do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitation or exclusion may not apply to

you.

This warranty gives you speciﬁc legal rights, and you may also have other legal

rights which vary from state to state.

5485458_S.4-38.fm Seite 13 Dienstag, 22. Januar 2002 10:22 10

14

FOR CANADA ONLY

2 year limited warranty

(foil and cutterblock excluded)

In the event a Braun appliance fails to function within 2 years from date of

purchase, because of defects in material or workmanship, and the consumer

returns the unit to an authorized service center, Braun Canada, will, at its option,

either repair or replace the unit without additional charge to the consumer.

This guarantee does not cover any product, which has been damaged by

dropping, tampering, wrong current, servicing performed or attempted by

unauthorized service agencies, misuse or abuse,

kinks in the shaver foil as

well as the normal wear of the shearing parts.

Exclusion of Warranties:

The foregoing warranty is the sole warranty offered by

Braun Canada. Braun Canada hereby disclaims any implied warranty of

merchantability or ﬁtness for any particular purpose. In no event will Braun

Canada be responsible for consequential dam-ages resulting from the use of this

product.

5485458_S.4-38.fm Seite 14 Dienstag, 22. Januar 2002 10:22 10

Page is loading ...

Braun 5441 User manual

This manual is also suitable for

Braun 5441 User manual

in other languages

Related papers

Other documents