Drop-In 4 Burner Gas Grill
Parrilla de Gas con 4 Quemadores
OWNER’S MANUAL/MANUAL DEL PROPIETARIO
ASSEMBLY AND OPERATING IN STRUC TIONS
INSTRUCCIONES DE ARMADO Y OPERACIÓN
WARNING/ADVERTENCIA
HAZARDOUS EXPLOSION MAY RESULT IF THESE WARNINGS
AND INSTRUCTIONS ARE IGNORED. READ AND FOLLOW ALL
WARNINGS AND INSTRUCTIONS IN THIS MANUAL TO AVOID
PERSONAL INJURY, INCLUDING DEATH OR PROPERTY DAMAGE.
SE PUEDE PRODUCIR UNA EXPLOSIÓN PELIGROSA SI SE HACE
CASO OMISO A ESTAS ADVERTENCIAS E INSTRUCCIONES. LEA
Y SIGA TODAS LAS ADVERTENCIAS E INSTRUCCIONES EN ESTE
MANUAL PARA EVITAR LESIONES PERSONALES, INCLUSO LA
MUERTE, O LOS DAÑOS MATERIALES.
NOTICE TO INSTALLER:
LEAVE THESE INSTRUCTIONS
WITH GRILL OWNER FOR FUTURE
REFERENCE .
AVISO PARA EL INSTALADOR:
ENTREGUE ESTAS INSTRUCCIONES AL
PROPIETARIO DE LA PARRILLA PARA
REFERENCIA FUTURA.
SAVE THIS MANUAL FOR FUTURE REFERENCE
GUARDE ESTE MANUAL PARA REFERENCIA FUTURA
Model/Modelo GAS8490AS
®
1
WE WANT YOU TO ASSEMBLE AND USE YOUR GRILL AS SAFELY AS POSSIBLE.
THE PURPOSE OF THIS SAFETY ALERT SYMBOL
IS TO ATTRACT YOUR ATTENTION
TO POSSIBLE HAZARDS AS YOU ASSEMBLE AND USE YOUR GRILL.
WHEN YOU SEE THE SAFETY ALERT SYMBOL
PAY CLOSE ATTENTION TO THE INFORMATION WHICH FOLLOWS!
READ ALL SAFETY WARNINGS AND INSTRUCTIONS CAREFULLY
BEFORE ASSEMBLING AND OPERATING YOUR GRILL.
DANGER
IMPORTANT SAFETY
WARNINGS
IF YOU SMELL GAS:
1. Shut off gas to the appliance.
2. Extinguish any open ame.
3. Open lid.
4. If odor continues, keep away from the appliance and immediately call your gas supplier or your
re department.
1. Do not store or use gasoline or other ammable liquids or vapors in the vicinity of this or any
other appliance.
2. An LP cylinder not connected for use shall not be stored in the vicinity of this or any other
appliance.
a) Do not store a spare LP cylinder under or near this appliance.
b) Never ll the cylinder beyond 80% full.
c) If the information in (a) and (b) is not followed exactly, a re causing death or
serious injury may occur.
WARNING
DANGER
2
General Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
LP Gas Cylinder (Tank) Speci cations and Installation. . . . . . . . . . . . . . . . 4-6
Hose & Regulator Speci cations and Installation . . . . . . . . . . . . . . . . . . . . 6-7
Leak Testing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
Pre-start Check List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Lighting Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10
Operating the Grill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11
Proper Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-13
Transporting and Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-16
Grill Cooking Tips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-24
Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING: Be alert to the possibility of serious bodily injury if the instructions are not followed. Be sure to read and
carefully follow all of the messages.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
TABLE OF CONTENTS:
CALIFORNIA PROPOSITION 65 WARNING
This product contains chemicals, and when used, produces
chemicals, including carbon monoxide, known to the State of California
to cause cancer and birth defects or other reproductive harm.
https://www.p65warnings.ca.gov
WARNING! CONTAINS LEAD. MAY BE HARMFUL IF EATEN OF CHEWED. MAY GENERATE
DUST CONTAINING LEAD.COMPLIES WITH FEDERAL STANDARDS.
KEEP OUT OF THE REACH OF CHILDREN.
FOR COVERS, ACCESSORIES AND OTHER PRODUCTS PLEASE VISIT
US ONLINE AT: www.embersgrills.com
3
WARNING
• Leak test all connections before rst use, even if grill was purchased fully assembled and after each
tank re ll. Check propane tank rubber seal for damage.
• Always check grill and propane tank prior to each use as indicated in “Checking for Leaks” & “Pre-
Start Check List” sections of this manual.
• Never use natural gas in a unit designed for liquid propane gas.
• Flavoring chips must be contained in a metal smoking box to contain ash and prevent res.
• Ensure ames come out of all burner ports at each use. Spiders and insects like to build nests in
burner tubes. Blocked burner tubes can prevent gas ow to burners and could result in a burner tube
re or re beneath grill.
• Never check for leaks using a match or open ame.
• Never use or store gasoline, lighter uid, paint thinner, or other ammable vapors and liquids or
combustible materials in or near your grill.
• DO NOT block ventilation areas in sides, back or cart compartment of grill.
• DO NOT cover cooking grates or other components with aluminum foil, as this blocks ventilation and
damage to grill or personal injury may occur.
• Keep children and pets away from hot grill. DO NOT allow children to use or play near this grill.
• DO NOT leave grill unattended while ON or in use.
• DO NOT allow gas hose to come in contact with hot surfaces. Redirect gas hose if necessary.
• DO NOT allow grease or hot drippings to fall on hose and regulator assembly. If this occurs, turn gas
supply OFF at once. Empty grease tray/cup and clean hose and regulator assembly and inspect for
damage before use.
• Never cook on grill without grease cup/tray in position.
• DO NOT use water on a grease re. Closing lid to extinguish a grease re is not possible. Use type
BC dry chemical re extinguisher or smother with dirt, sand or baking soda.
• DO NOT use while under in uence of drugs or alcohol.
• FOR OUTDOOR USE ONLY. DO NOT operate indoors or in an enclosed area such as a building,
garage, shed or breezeway.
• Position your grill outdoors on a non-combustible level surface in a well ventilated location, a safe
distance 10 ft. (3.1 m) from combustible materials, buildings and overhangs.
• Apartment dwellers: Check with management and follow requirements and re codes for using a
LP gas grill in your apartment complex. Only use outside on ground (not on a balcony, patio, garage,
etc) with a 15 foot (4.6 m) minimum clearance on back and all sides from any wall, structure or
combustible material.
• Maintain a minimum clearance of 36 inches (91 cm) between back and all sides of grill, deck railings,
walls or other combustible material. Not adhering to these clearances may prevent proper ventilation
and can increase risk of a re and/or property damage, which could also result in personal injury. DO
NOT use grill under overhead combustible construction.
• DO NOT use or install this grill in or on a recreational vehicle and/or boat.
• If a bristle brush is used to clean any cooking surfaces, ensure no loose bristles remain on cooking
surfaces prior to grilling as loose bristles may attach to food.
• DO NOT store items in cart that can catch re or damage your grill (such as swimming pool supplies/
chemicals, table cloth, wood chips).
GENERAL WARNINGS:
4
LP GAS CYLINDER (TANK) SPECIFICATIONS AND INSTALLATION:
• Grill is hot when in use. To avoid burns:
• DO NOT attempt to move the grill.
• Wear protective gloves or oven mitts.
• DO NOT touch any hot grill surfaces.
• DO NOT wear loose clothing or allow hair to come in contact with grill.
• Not for commercial use. DO NOT use this grill for anything other than its intended purpose.
USE CAUTION AND COMMON SENSE WHEN OPERATING YOUR GAS GRILL.
FAILURE TO ADHERE TO THE SAFETY WARNINGS AND GUIDELINES IN THIS MANUAL
COULD RESULT IN SEVERE BODILY INJURY OR PROPERTY DAMAGE.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
WARNING
• ONLY connect this grill to a Type 1 cylinder valve. The Type 1 valve can be identi ed with the
large external threads on the valve outlet.
• DO NOT connect to a propane cylinder exceeding a 20 lb. (9.1 kg) capacity.
• DO NOT connect to a cylinder that uses any other type of valve connection device.
• Inspect the propane tank valve rubber seal for cracks, wear or deterioration prior to use. A
damaged rubber seal can cause a gas leak, possibly resulting in an explosion, re or severe
bodily harm.
• Turn off the cylinder valve when your grill is not in use.
• Handle the tank with care.
• Always secure the cylinder in an upright position.
• Never connect an unregulated LP gas cylinder to your grill.
• DO NOT expose LP gas cylinders to excessive heat or ignition sources.
• DO NOT store a spare LP gas cylinder under or near your grill.
• Allow only quali ed LP gas dealers to ll or repair your LP gas cylinder.
• DO NOT allow the cylinder to be lled beyond 80% capacity.
• Read and follow all warnings and instructions that are on the cylinder and that accompany this
product.
• DO NOT store a spare LP gas cylinder (full or empty) under or near your grill. This could cause
excess pressure to be expelled through the vapor relief valve resulting in re, explosion, or
severe personal injury, including death.
• Propane gas is heavier than air and will collect in low areas. Proper ventilation is extremely
important. Keep the ventilation opening(s) of the LP gas cylinder enclosure free and clear from
obstructions and debris.
• DO NOT insert any foreign objects into the cylinder valve outlet as this could damage the
rubber seal. Do not use propane tank with a damaged rubber seal. A damaged rubber seal can
cause a gas leak, possibly resulting in explosion, re, severe bodily harm, or death. Inspect
rubber seal for cracks, wear or deterioration prior to use.
• Always keep cylinder (tank) in upright position during use, transit or storage.
DANGER
5
• Allow only quali ed licensed LP gas dealers to properly ll or repair your LP gas cylinder.
• New tanks should be purged prior to lling; inform LP gas dealer if you are using a new tank.
• DO NOT allow the cylinder to be lled beyond 80% capacity. Over- lled tanks can create a
dangerous condition. Over- lled tanks can build-up pressure and cause the relief valve to expel
propane gas vapors. The vapor is combustible and if it comes in contact with a spark source or
ame an explosion causing severe burns, bodily harm, or death could occur.
• Always use a protective cylinder cap when grill is not connected to cylinder.
• If you exchange a cylinder with a quali ed exchange program, the new cylinder must have
a Type 1 valve and an over- lling prevention device (OPD).
• Inspect the propane tank valve rubber seal for cracks, wear or deterioration prior to use. A
damaged rubber seal can cause a gas leak, possibly resulting in an explosion, re or severe
bodily harm.
FILLING THE LP GAS CYLINDER (TANK):
WARNING
LP GAS CYLINDER (TANK) SPECIFICATIONS:
LP gas cylinder (not supplied with this grill)
The LP (Liquid Propane) gas cylinder speci cally designed to be used with this grill must be 12” (30.5 cm)
diameter x 18” (45.7 cm) tall and have a 20 lb. (9.1 kg) capacity incorporating a Type 1 cylinder valve and
an over- lling protection device (OPD).
This grill is designed to t Worthington, Manchester or SMPC brand 20 lb. (9.1 kg) cylinders. Other brand
DOT cylinders may t this grill if cylinder has similar dimensions of top and bottom rings.
The installation of this appliance must be in accordance with:
All applicable local codes, or in the absence of local codes, either:
• National Fuel Gas Code ANSI Z223.1 NFPA 54
• Natural Gas and Propane Installation Code: CAN/CGA B149.1
• Natural Gas Installation Code: CAN/CGA B149.1 (Canada)
• Propane Installation Code: CAN/CGA B149.2 (Canada)
To check your local codes, see your local LP gas dealer or natural gas company.
When purchasing or exchanging a cylinder for your gas grill, it must be constructed and marked in
accordance with speci cations for LP gas cylinders of the U.S. Department of Transportation (DOT) or
the National Standard of Canada, CAN/CSA-B339 Cylinders, Spheres and Tubes for Transportation of
Dangerous Goods; and Commission, as applicable; and provided with a listed over- lling prevention device
(OPD), and provided with a cylinder connection device compatible with connection for outdoor cooking
appliances.
The cylinder must also be equipped with:
• A shut-off valve terminating in a Type 1 gas cylinder valve outlet.
• A Type 1 valve that prevents gas ow until a positive seal is obtained.
• An arrangement for vapor withdrawal.
• A collar to protect cylinder shut-off valve.
• A safety relief device having direct communication with vapor space of the cylinder.
• A listed over- lling prevention device (OPD).
6
INSTALLING THE LP GAS CYLINDER (TANK)
ONTO THE GRILL:
1. Check that the cylinder valve is closed by turning knob
clockwise. Inspect cylinder valve rubber seal for cracks or
deterioration. Do not use propane tank with damaged seal
as a gas leak may occur.
2. Place cylinder in tank holder in an upright position.
3. Orient cylinder so valve opening faces right side of the
grill.
4. Fully tighten tank holder screw.
• Inspect propane tank valve rubber seal for cracks, wear
or deterioration prior to use. A damaged rubber seal can
cause a gas leak, possibly resulting in an explosion, re
or severe bodily harm.
• Inspection should be done each time propane tank is
connected to grill, has been re lled, exchanged or has
not been used for more than 60 days.
• Do not use a propane tank with a damaged rubber
seal. Exchange tank or have rubber seal replaced at a
quali ed propane lling station.
LP GAS CYLINDER (TANK) RUBBER SEAL INSPECTION:
Good
Rubber Seal
Damaged
Rubber Seal
HOSE & REGULATOR SPECIFICATIONS AND INSTALLATION:
• DO NOT attempt to connect grill, as purchased for LP (propane) gas, to any other fuel supply
source such as a natural ga
s line. For dual fuel grills that can be converted to natural gas, a
3 Embers conversion kit must be purchased and installed for use with natural gas.
• DO NOT use any other pressure regulator/hose assembly other than the one supplied with your
grill. Replacement pressure regulator/hose assembly must be part No 7480-155-7480-0, which can be
obtained by contacting customer service at 855-735-9922.
• DO NOT attempt to adjust or repair a regulator. The regulator is designed to operate at a
maximum output pressure of 11 inches of water column (2.74 kPa).
• Ensure the tank valve is CLOSED prior to connecting the LP gas cylinder to your grill. Turn the
valve knob clockwise to properly close the valve. Read and follow all instructions and warnings
on the supply hose safety tags. Read and follow all warnings in this manual concerning the safe
use of LP gas cylinders and the hose and regulator before connecting cylinder to grill. Read and
follow all warnings on the LP cylinder.
WARNING
Tank holder screw
7
HOSE AND REGULATOR:
Your grill is equipped with a Type 1 connection device with the following features:
1. The system will not allow gas ow from cylinder until a positive connection to valve has been made.
Note: The cylinder valve and all grill burner knobs must be turned OFF before any connection is made or
removed.
2. A regulator ow limiting device, when activated, restricts the ow of gas to 10 cubic feet per hour. If the
ow limiting device is activated, perform Regulator Resetting Procedure.
Note: If your grill will not get hot enough to cook, the ow limiting device may have been activated.
CONNECTING HOSE AND REGULATOR:
1. Inspect propane tank valve rubber seal for cracks, wear or deterioration
prior to use. A damaged rubber seal can cause a gas leak, possibly
resulting in an explosion, re or severe bodily harm. Do not use a
propane tank with a damaged rubber seal.
2. Attach or detach regulator to the LP gas cylinder only when cylinder is
at rest in tank holder.
3. Check that the cylinder valve is closed by turning knob clockwise.
4. Check that the grill’s burner control knobs are “OFF”.
5. Visually inspect hose prior to each use for damage, excess wear, or
deterioration. If found, replace hose before using your grill. Only the
manufacturer’s supplied replacement should be used.
6. Remove the protective plastic cap from cylinder valve.
7. Check that the hose does not contain kinks, does not contact sharp edges, and does not contact
surfaces that may become hot during use.
8. Hold regulator and insert the brass nipple into LP cylinder valve outlet. Ensure that the device is
centered properly.
9. Turn large coupling nut clockwise by hand and tighten to a full stop. Take care not to cross thread
coupling nut onto cylinder valve. Do not use tools to tighten connection.
Note: If you are unable to make connection, repeat Steps 7 and 8.
10. Leak check all ttings before lighting your grill. See section on “Leak Testing” in this manual.
Note: To remove regulator from propane tank, turn off tank valve and rotate large coupling nut
counter-clockwise and remove.
REGULATOR RESETTING PROCEDURE:
If your grill will not get hot enough to cook, the ow limiting device may have been activated.
Mini Reset:
Turn ALL burner control knobs to “OFF”, turn off cylinder valve. Wait one minute. Slowly turn cylinder
valve ON and relight grill. If burner ame is higher and grill heats up properly – proceed with cooking.
Full Reset:
Turn ALL burner control knobs to “OFF”, turn off cylinder valve. Disconnect hose and regulator from cylinder.
Wait two minutes, reattach hose and regulator and perform leak test.
WARNING
• Never use your grill without leak testing all gas connections, hoses and propane tank. Follow
the section on “Leak Testing” in this manual for proper procedures.
LEAK TESTING:
Inspect Rubber Seal (see page 6)
To prevent re or explosion hazard:
• DO NOT smoke or permit ignition sources in the area while conducting a leak test.
• Perform test OUTDOORS in a well ventilated area that is protected from the wind.
• Never perform a leak test with a match or open ame.
• Never perform a leak test while the grill is in use or while grill is still hot.
DANGER
WHEN TO PERFORM A LEAK TEST:
• After assembling your grill and before lighting for the first time, even if purchased fully assembled.
• Every time LP gas cylinder is refilled, exchanged or if any of the gas components are disconnected or replaced.
• Any time your grill has been moved.
• At least once per year or if your grill has not been used for more than 60 days.
CHECKING FOR LEAKS:
CAUTION: Strong odors, colds, sinus congestion, etc. may prevent the detection of propane by smell.
Use caution and common sense when testing for leaks.
Note: The leak test must be performed in an area that has adequate lighting in order to see if bubbles are
developing and not in a windy or noisy area so larger leaks can be detected by smell or sound.
1. Create a mixture of 50% water and 50% liquid dishwashing soap.
2. Open lid.
3. Ensure all control knobs are set to “OFF”.
4. Turn on gas at cylinder valve. Turn cylinder valve knob one turn
counter-clockwise. If you hear a rushing sound or smell gas,
turn gas off. Tighten any leaking connections. If leak is detected
at connection nut and tightening does not stop leak, reinspect
propane tank rubber seal.
5. Apply the soap water mixture to the following:
Supply tank (cylinder) weld.
Connection nut to tank valve.
Back connection nut to brass nipple.
Brass nipple connection into regulator.
Regulator connections to gas supply hoses.
The full length of gas supply hose.
Hose connection to gas manifold.
Tank valve to cylinder.
Connections to brass adaptor
6. Check each place listed (A–I) for growing bubbles, which indicates
a leak. Large leaks may not be detected by bubbles but should
produce a rushing sound or gas smell.
7. Turn off gas supply at cylinder valve.
8. Turn on control knobs to release gas pressure in hose.
9. Turn control knobs “OFF”.
10. Tighten any leaking connections. If leak is detected at connection
nut and tightening does not stop leak, reinspect propane tank
rubber seal. (see page 6)
11. Repeat soapy water test until no leaks are detected.
12. Turn off gas supply at cylinder valve until you are ready to use
your grill.
13. Wash off soapy residue with cold water and towel dry.
14. Wait 5 minutes to allow all gas to evacuate area before lighting
grill.
WARNING: DO NOT use grill if leaks cannot be stopped. Contact
a qualified gas appliance repair service.
8
A
B
C
D
E
F
G
H
Watch For Bub bles
I
H
I
E
D
C
B
A
F
G
F
9
LIGHTING THE MAIN BURNERS:
1. Open lid before lighting burner.
2. Make sure all control knobs are “OFF”.
3. Select burner to be lit. Push and hold down control knob and turn SLOWLY
(2 to 3 seconds) to “HIGH”. You should hear igniter click.
Note: Step 3 may need to be repeated 2-3 times to light grill.
4. If ignition does NOT occur in 5 seconds, turn control knob to “OFF”,
wait 5 minutes to allow gas to dissipate and repeat lighting procedure.
5. To light other burners, follow steps 3-4.
WARNING
DANGER
Property damage, bodily harm, severe burns, and death could result from failure to follow these
safety steps. These steps should be performed after the grill has been assembled and prior to
each use. DO NOT operate this grill until you have read and understand ALL of the warnings and
instructions in this manual.
• Ensure that the grill is properly assembled.
• Inspect gas supply hose for burns, chaffing, kinks, and proper routing before each use. If it is evident
there is excessive abrasion or wear, or the hose is cut, it must be replaced prior to grill being used.
Replace with hose and regulator Model No. 7480-155-7480-0, which can be obtained by contacting
customer service at 855-735-9922.
• Leak check all gas connections, hose and propane tank. See section on “Leak Testing”.
• Position your grill on a non-combustible level surface in a well ventilated location, a safe distance
10 ft. (3.1 m) from combustible materials, buildings and overhangs.
• Properly place empty grease cup under grease drain hole in bottom of grill to catch grease during use.
• DO NOT block ventilation areas in sides, back or cart compartment of grill.
PRE-START CHECK LIST:
LIGHTING INSTRUCTIONS:
Read, understand and follow all warnings and instructions contained in this manual. DO NOT skip any
of the warnings and instructions contained in the preceding sections of this manual.
Follow the instructions exactly.
1. OPEN THE GRILL LID before attempting to light a burner so that fumes do not accumulate inside
the grill. An explosion could occur if grill lid is down.
2. Check that all burner control knobs and the cylinder valve are turned to the “OFF” position.
3. Turn on the fuel supply by slowly rotating the cylinder valve knob counter-clockwise to full open.
4. DO NOT stand with head, body, or arms over the grill when lighting.
OFF
HIGH
10
6. If burner does not ignite using igniter, see “Match Lighting the Main Burners” section.
7. To turn off, turn each control knob clockwise until it locks in the “OFF” position. This does not turn off
the gas ow from the cylinder.
Note: If burner does not light or ame is too low, See “Trouble Shooting” section of the owners manual.
MATCH LIGHTING THE MAIN BURNER:
1. Open lid before lighting burner.
2. Make sure all control knobs are “OFF”.
3. Place a paper match in the end of the match lighter. Strike match and
place through the cooking grate approximately 1/2” (1 to 2 cm) from
the burner to be lit.
4. Turn burner control knob to “HIGH” position. The burner should light
within 5 seconds.
5. If burner does not light, turn control knob to “OFF” and wait 5 minutes
for gas to dissipate and repeat lighting procedure.
6. Once lit, light adjacent burners by following steps 3-6.
7. If burner does not light within rst few attempts of match lighting, there is a problem with the gas supply.
Turn off gas at burner and cylinder. DO NOT attempt to operate grill until the problem is found and
corrected.
Note: If burner does not light or ame is too low, See “Trouble Shooting” section of the owners manual.
Match
• Read and follow all warnings and instructions contained in the preceding sections of this
manual.
• Flavoring chips must be contained in a metal smoking box to contain ash and prevent res.
• DO NOT cover cooking grates or other components with aluminum foil, as this blocks
ventilation and damage to grill or personal injury may occur.
• DO NOT leave your grill unattended while “ON” or in use.
• DO NOT move grill when in use.
• DO NOT use water on a grease re. Closing the lid to extinguish a grease re is not possible.
Use type BC dry chemical re extinguisher or smother with dirt, sand or baking soda.
• Never cook on the grill without the grease cup/tray in place.
WARNING
OPERATING THE GRILL:
BREAKING IN YOUR GRILL:
• In manufacturing and preserving the components of your grill, oil residue may be present on burners
and cooking surfaces of your grill.
• Before cooking on your grill for the rst time you should preheat it for 15 minutes on “HIGH” to burn off
these residual oils.
PREHEATING GRILL:
• Prior to each use, it is recommended that you preheat your grill. This ensures that the grilling surfaces
are at the desired temperatures to sear the food sugars when cooking. After lighting your grill, set main
burner control knobs to “HIGH” position for 5 to 10 minutes. Close lid during the preheat period.
11
CONTROLLING FLARE-UPS/GREASE FIRES:
• Flare-ups are a part of cooking meats on a gas grill. This adds to the unique avor of cooking on a
gas grill. Use caution when opening lid as sudden are-ups may occur. Excessive are-ups can over-
cook your food and cause a dangerous situation for you and your grill. Excessive are-ups result from
the build-up of grease in your grill. If this should occur, DO NOT pour water onto the ames. This can
cause grease to splatter and could result in serious burns or bodily harm.
• If grease re occurs while lid is open, leave lid open, turn burner knobs to “OFF”, turn off LP cylinder
valve. If possible, relocate food to a different section of cooking grate and allow grease to burn out or
smother ames with baking soda.
• If grease re occurs while lid is closed, leave lid closed, as a sudden burst of air may increase ames.
Turn burner knobs to “OFF”, turn off LP cylinder valve. Allow grease to burn out.
• Never pour water on a grease re as grease may splatter/spread and could result in bodily injury or
property damage.
• If grease re does not quickly burn out or re is growing/spreading, use type BC dry chemical re
extinguisher or smother with dirt, sand or baking soda. Closing lid to extinguish a grease re is not
possible.
TO MINIMIZE FLARE-UPS:
• Trim excess fat from meats prior to cooking.
• Cook meats with high fat contents (chicken or pork) on Low settings or indirectly.
• Ensure that your grill is on level ground and grease is allowed to evacuate grill
through drain hole in bottom and into grease cup/tray.
• Clean grill frequently to minimize grease buildup.
INDIRECT COOKING:
• Indirect cooking is the process of cooking your food without heat source being directly under your
food. You can sear meats over a high ame on one side of the grill while slow cooking a roast on the
other (unlit) side of the grill.
TURNING OFF THE GRILL:
1. Turn off cylinder valve.
2. Turn all burner control knobs to “OFF” position.
Note: Turn off LP cylinder rst to prevent gas from being left in the system under
pressure.
CAUTION:
• The cylinder valve should always be in the off, or closed, position when grill is not in use.
ROTISSERIE COOKING:
• Your grill was pre-drilled from the factory to include mounting holes for a rotisserie. Compatible with the
3 Embers® Stainless Steel Rotisserie Kit - Model ACC7100AS (sold separately).
• Read and follow all instructions provided with the rotisserie. Save instructions for future reference.
OFF
HIGH
MED
LOW
To turn off cylinder valve,
turn knob clockwise until it
stops.
12
WARNING: If a bristle brush is used to clean any of the cooking surfaces, ensure no loose bristles remain
on the cooking surfaces prior to grilling as loose bristles may attach to food.
CLEANING INTERIOR OF GRILL:
• We recommend cleaning off food residue immediately after cooking by gently scrubbing grates with bristle brush and then
turning burners to HIGH for approximately 5 minutes.
• Make sure unit has adequately cooled before cleaning.
• Clean up of the grill after each use is required.
WARNING: DO NOT leave grill unattended when grill is on. Wear oven mitts to protect from burns.
• The heat from burners will burn off most food/grease residue from grates & heat tents and turn it to an ash like substance
which will fall to the bottom of the rebox or grease tray. After the grill cools (approximately 30 minutes) remove grates
and heat tents and brush the ash and any grease out of the rebox. Clean and replace grease cup. Inspect the heat tents
for damage or deterioration before reinstalling in the grill. Don’t scrap or brush heat tents to avoid damage to screens.
(Replacements can be ordered by calling 855-735-9922.)
CAUTION: DO NOT allow ash residue to remain on grease tray or rebox as it could block proper grease
drainage of the grill.
INTERIOR OF GRILL LID:
• Smoke will accumulate inside grill lid and may ake onto your food. Clean the inside of the grill lid with scrub brush and
baking soda/water solution. Dry thoroughly. Do not mistake this for paint. The interior of gas grill lids are not painted.
MAINTAINING EXTERIOR OF GRILL:
• To protect your grill from excessive rust, the unit must be kept clean and covered at all times when not in use.
• Painted surfaces. Wash with mild detergent or non-abrasive cleaner and warm soapy water.
• Stainless steel surfaces. To maintain your grill’s appearance, wash with mild detergent and warm soapy water and wipe
dry with a soft cloth after each use. Baked-on grease deposits may require the use of an abrasive plastic cleaning pad.
Use only in direction of brushed nish to avoid damage. Do not use abrasive pad on areas with graphics. Car wax may
help protect the exterior nish of your grill.
• Porcelain surfaces. Because of glass-like composition, most residue can be wiped away with a solution of baking soda
and water or specially formulated cleaner. Use non-abrasive scouring powder such as baking soda for stubborn stains.
• Plastic and rubber parts. Wash with warm soapy water and wipe dry. Do not use citrisol, abrasive cleaners, degreasers or
a concentrated grill cleaner on plastic parts. Damage to and failure of parts can result.
RUST:
• Discoloration, rust and rust pits can occur as a result of high cooking temperatures, acidic marinades, grease res and
exposure to coastal climates or other natural elements.
• Rust spots on the interior surface can be buffed, cleaned, then lightly coated with vegetable oil or vegetable oil spray to
minimize rusting.
• Never use cleaners containing chlorine or store swimming pool supplies or chemicals in cart compartment as chlorine
promotes rust.
PROPER CARE & MAINTENANCE:
BURNER CLEANING AND MAINTENANCE:
• Keep appliance free and clear of combustible materials, gasoline and other ammable vapors and liquids.
• Keep ventilation openings of cylinder enclosure free and clear of debris.
• Visually check burner ames for proper operation (see pictorial in “Burner Assembly/Maintenance” under Proper Care and
Maintenance). Spiders or other insects can nest in the burner causing gas blockage.
• For safe grilling and peak performance of your grill, perform these checks at least twice per year or after extended
periods of storage.
• Be sure to tighten up all hardware (nuts, bolts, screws, etc.) at least twice per year.
CAUTION: Some parts may contain sharp edges. Wear protective gloves if necessary.
• Remove cooking grills, heat distribution plates, and burners from inside your grill. Use a brush with hot water and
detergent to remove excess residue. NEVER use a commercial oven cleaner. Rinse completely with water. Towel dry and
replace all components as described in the assembly instructions.
13
BURNER ASSEMBLY/MAINTENANCE:
• Although your burners are constructed of stainless steel, they
may corrode as a result of the extreme heat and acids from
cooking foods. Regularly inspect burners for cracks, abnormal
holes, and other signs of corrosion damage. If found, replace
burner.
• DO NOT block ventilation areas in sides, back or cart
compartment of grill. Burner tubes can become blocked by
spiders and other insects building their nests. Blocked burner
tubes can prevent gas ow to the burners and could result in a
burner tube re or re beneath the grill. To clean burner follow
these instructions.
1. Turn gas off at control knobs and LP cylinder tank valve.
2. Remove cooking grills and heat distribution plates.
3. Remove the cotter pin and stud from each burner.
4. Remove burner.
5. Use a narrow bottle brush or a stiff wire bent into a small hook
to run through each burner tube or use compressed air to blow
into burner tube and out the ame ports. Check each port to
make sure air comes out each hole.
CAUTION: Wear eye protection when using compressed air.
6. Use a wire brush to clean the entire outer surface of burner to
remove food residue and dirt.
7. Check burner for damage, if any cracks or holes are
found replace burner.
8. Install burner in grill, orient burners CORRECTLY.
IMPORTANT: Burner opening must slide over valve nozzle.
9. Replace the stud and cotter pin.
Note: Follow the “Gas Leak Testing” section of this
manual. Relight burners to verify proper operation.
10. Replace heat distribution plates and cooking
grills.
Debris
Stud
PROPER VALVE TO BURNER ALIGNMENT
Valve Nozzle
Burner Opening
Note: Normal ame height is 1˝ to 2˝
Cotter pin
14
BEFORE STORING YOUR GRILL:
• Ensure that cylinder valve is fully closed.
• Clean all surfaces. Lightly coat burners with cooking oil to prevent excess rusting.
• If storing grill indoors, disconnect LP tank and leave LP tank OUTDOORS.
• Place dust cap on cylinder valve outlet whenever the cylinder is not in use. Only install the type of dust cap on the
cylinder valve outlet that is provided with the cylinder valve. Other types of caps or plugs may result in leakage of
propane.
• Check and clean burner prior to use after storing, at the beginning of grilling season or after a period of not being
used. Spiders and insects like to build nests in burner tubes (especially during colder months). Blocked burner tubes
can prevent gas ow to burners and could result in a burner tube re or re beneath grill. See “Burner Assembly/
Maintenance” under Proper Care and Maintenance.
• If storing grill outdoors, cover grill with a grill cover for protection from the weather.
• Never move a grill when hot or in use.
• Make sure that cylinder valve is closed and burner knobs are in the off position.
• DO NOT store a spare LP gas cylinder ( lled or empty) under or near the grill.
• Never store ammable liquids or spray canisters under or near the grill.
• If the outdoor cooking gas appliance is not in use, the gas must be turned off at the LP gas
supply cylinder.
• Storage of an outdoor cooking gas appliance indoors is permissible only if the cylinder is
disconnected and removed from the outdoor cooking gas appliance.
• Cylinders must not be stored in a building or enclosure, including garages and sheds.
• Cylinders must be kept out of reach of children.
WARNING
TRANSPORTING AND STORAGE:
15
TROUBLE SHOOTING:
Problem Possible Cause Prevention/Cure
Burner will not light LP gas tank valve is closed Make sure regulator is securely attached to the LP gas tank, turn LP
gas tank valve to “OPEN”
LP gas tank is low or empty Check if LP gas tank is empty. If empty, replace or re ll.
LP gas leak 1. Turn LP gas tank valve to “CLOSED”
2. Wait 5 minutes for gas to clear
3. Follow “Leak Testing” in the owner’s manual
Coupling nut and regulator not fully connected See section on “Connecting Hose and Regulator”
Obstruction of gas ow 1. Clean burner assembly
2. Check for bent or kinked hose
Burner may not be properly seated Reseat burner and valve. Refer to “Burner Assembly/Maintenance”
instructions
Spider webs or insect nest in venturi Clean venturi and burner assembly
Burner ports clogged or blocked Clean burner ports
Battery needs to be changed Replace the battery (follow assembly step for inserting battery)
Wires or electrode covered with cooking residue Clean wire and/or electrode with rubbing alcohol
Electrode and burners are wet Wipe dry with cloth
Electrode cracked or broken - sparks at crack Replace electrode
Wire loose or disconnected Reconnect wire or replace electrode/wire assembly
Wire is shorting (sparking) between ignitor and
electrode
Replace ignitor wire/electrode assembly
Bad ignitor Replace ignitor
Grill does not get hot
enough
Out of gas Replace or re ll LP gas tank
Flow limiting device may have been activated 1. Mini Reset:
a. Turn control knobs and LP gas tank valve to “OFF”
b. Wait one minute and relight grill per “Lighting Instructions”
2. If ames are still too low, perform a Full Reset
Full Reset:
a. Turn control knobs and LP gas tank valve to “OFF”
b. Disconnect regulator from propane tank
c. Inspect LP cylinder rubber seal
d. Wait 1 minute
e. Reconnect regulator and perform “Leak Testing” on all
connections.
f. Light grill per “Lighting Instructions”
Irregular ame pattern.
Flame does not run full
length of burner
Burner ports are clogged or blocked
Air shutter on burner needs adjustment
Clean burner ports
See section on “Burner Adjustment”
Flame is yellow or orange New burner may have residual manufacturing
oils
Burn grill for 15 minutes on “HIGH” with the lid closed
Spider webs or insect nest in venturi Clean venturi and burner assembly
Food residue, grease, etc. Clean burner assembly
Poor alignment of valve to burner venturi
Air shutter on burner needs adjustment
Make sure burner venturi is properly engaged with valve
See section on “Burner Adjustment”
16
Problem Possible Cause Prevention/Cure
Flame blows out High or gusting winds Do not use grill in high winds
Low on LP gas Replace or re ll LP gas tank
Burner holes may be obstructed Refer to “Burner Assembly/Maintenance” instructions
Flow limiting device tripped Refer to “Regulator Resetting Procedure”
Flare-up Grease buildup Clean all grill parts per “Proper Care and Maintenance” instructions
Excess fat in meat Trim fat from meat before grilling
Excessive cooking temperature Adjust (lower) cooking temperature
Grease re Grease trapped by food buildup around burner
system
1. Turn control knobs and LP gas tank valve to “OFF”
2. Leave lid in open or closed position and let re burn out. Use BC
type re extinguisher or baking soda, sand or dirt to smother re,
if necessary.
3. After grill cools, remove and clean all parts per “Proper Care and
Maintenance” instructions
Flashback ( re in burner
tubes) / knobs melting
Burner and/or burner tubes are blocked Clean burners and/or burner assembly
Inside of lid is peeling
(like paint peeling)
Baked on grease buildup has turned into carbon
and is aking off
Clean thoroughly per “Proper Care and Maintenance” instructions
GRILL COOKING TIPS:
CLEANLINESS:
• Always wash hands thoroughly with soap and hot water prior to handling food and after handling raw
meat, uncooked poultry or seafood.
• When using a platter to carry raw meat, uncooked poultry or seafood to grill, make sure to wash platter
thoroughly with soap and hot water before placing cooked foods back on platter or use different platters
for raw and cooked foods.
• Never use same utensils when handling raw meat, uncooked poultry or seafood unless you wash
utensils thoroughly with soap and hot water.
• Never re-use marinade from raw meat or uncooked poultry on foods that have been cooked and are
ready to be served.
GRILLING TO PROPER TEMPERATURE:
• Use a meat thermometer to be sure food has reached a safe internal temperature.
• The USDA recommends the minimum temperature be reached for the following food items:
HELPFUL HINTS:
• If you pre-cook meat or poultry, do so immediately before grilling.
• Never defrost meat at room temperature or on a countertop.
• Refrigerate leftovers within 2 hours of taking food off the grill.
• For additional information, please phone the USDA’s toll free Meat & Poultry Hotline at 800-535-4555.
Chops . . . . . . . . . . . . . . . . . . . 145° F (62.8° C)
Ground Meat . . . . . . . . . . . . . . 160° F (71° C)
Pork . . . . . . . . . . . . . . . . . . . . . 145° F (62.8° C)
Poultry . . . . . . . . . . . . . . . . . . . 165° F (82° C)
Roasts . . . . . . . . . . . . . . . . . . . 145° F (62.8° C)
Seafood . . . . . . . . . . . . . . . . . . 145° F (60° C)
Vegetables . . . . . . . . . . . . . . . . 145° F (62.8° C)
17
ASSEMBLY INSTRUCTIONS:
READ ALL SAFETY WARNINGS & ASSEMBLY INSTRUCTIONS CAREFULLY
BEFORE ASSEMBLING OR OPERATING YOUR GRILL.
WE RECOMMEND TWO PEOPLE WORK TOGETHER WHEN AS SEM BLING THIS UNIT.
The following tool is required to assemble this 3 Embers® Drop-In 4 Burner Gas Grill:
• Phillips Screwdriver
3 AA Batteries
1 Battery Box Holder
1 Battery Box
1 Tank Holder
1 Clamp Mounting Bracket
2 Clamp Mounting Screws
PARTS LIST:
1 Grill Body
1 Warming Rack
3 Stainless Steel Cooking Grates
4 Stainless Steel Heat Tents
2 Grease Cup Brackets
1 Grease Cup
1 Grease Tray
1
2
3
4
5
6
7
8
11
9
10
Note: Screws needed for assembly are pre-installed and will need to be loosened
partially and/or removed to assemble grill.
1 Bandeja para grasa
3 Bateries AA
1 Soporte de caja de la batería
1 Caja de batería
1 Sostenedor del tanque
1 Abrazadera de montaje de la
abrazadera
2 Tornillos de montaje de la abrazadera
LISTA DE PARTES:
1 Cuerpo de la Parrilla
1 Rejilla para calentar
3 Rejilla para Cocinar de
Acero Inoxidable
4 Placas Térmicas de
Acero Inoxidable
2 Soportes de la bandeja de grasa
1 Recipiente para Grasa
1
2
3
4
5
6
8
11
9
10
Nota: Los tornillos necesarios para el montaje están preinstalados y deberán ser
a ojados parcialmente y / o retirados para ensamblar la parrilla.
7
12
13
12
13
18
12
3
4
5
6
7
8
11
9
10
12
13
19
PLACEMENT OF THE GRILL
Location
When determining a suitable location take into account concerns such as exposure to
wind, proximity to traffic paths, and keeping gas supply lines as short as possible. Place the
grill in well ventilated areas. Never locate the grill in a building, garage, breezeway, shed or
other such enclosed areas. During heavy use, the grill will produce a lot of smoke. For your
comfort, we recommend a nished height for your grill base of 36 to 38 inches (91.4 to 96.5
cm) and a minimum of 12 inches (30.5 cm) on either side of your grill.
Clearance
Non-Combustible Construction
A minimum of 10 inches (25.4 cm) clearance from the back of the grill to non-combustible
materials are required for the lid to open fully. Your grill base should incorporate an enclo-
sure to protect the LP cylinder from heat, ames and foreign materials such as grease drip-
pings. The enclosure should allow quick access to the LP cylinder valve. There should be a
minimum clearance of 2 inches between the base of the LP gas cylinder and the ground.
Ventilation
We recommend that adequate ventilation be incorporated into your drop-in grill base. Vents
should be placed on both sides of your grill base. The upper vent opening should be at
least 20 square inches (129 cm2) and located within 5 inches (12.7 cm) of the top edge of
your grill base. The lower vent opening should be at least 10 square inches (64.5 cm2) and
located within 1 inch (2.5 cm) or less from oor level of your grill base.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
Even Embers GAS8490AS Owner's manual
- Category
- Barbecues & grills
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI