U-tec B086DR2CZX Ultraloq U-Bolt WiFi Smart Lock User guide

Type
User guide

This manual is also suitable for

U-tec U-tec B086DR2CZX Ultraloq U-Bolt WiFi Smart Lock offers keyless convenience and enhanced security for your home. With its anti-peep keypad and smartphone compatibility, you can unlock your door using personalized codes or the U-tec App. The auto-lock feature ensures your door is always securely locked, and the low battery alarm alerts you when it's time for a change. Plus, the emergency key override provides peace of mind in case of battery failure.

U-tec U-tec B086DR2CZX Ultraloq U-Bolt WiFi Smart Lock offers keyless convenience and enhanced security for your home. With its anti-peep keypad and smartphone compatibility, you can unlock your door using personalized codes or the U-tec App. The auto-lock feature ensures your door is always securely locked, and the low battery alarm alerts you when it's time for a change. Plus, the emergency key override provides peace of mind in case of battery failure.

Ultraloq U-Bolt WiFi
Installation and User Guide
( V 1.0)
• Do not use a power drill for installation.
• Install and test the lock with the door open to avoid being
locked out.
• Please read all the instructions before contacting customer
support.
• Please contact customer support before returning the
product to the store.
• DO NOT install the batteries before installing the lock!
• Follow the instructions in sequential order!
This lock is designed for the following operating temperatures:
Outside Lock Body: -31°F(-35°C) to 158°F (70°C)
Inside Lock Body: 14°F (-10°C) to 131°F (55°C)
• Please must use AA Alkaline Battery and don't use Lithium Battery
or Rechargeable Battery.
To ensure the best service, please register your account at
www.u-tec.com/register.html
Need Help?
For technical documents and more
Please visit www.u-tec.com/support
Email: support@u-tec.com
Important Notes
Statements
- 1 -
Before using all Ultraloq products, please read all applicable terms,
rules, policies and usage provisions found at
www.u-tec.com/company/privacy. By using your Ultraloq, you
agree to be bound by the U-tec Privacy Policy.
Ultraloq Terms & Policies
Interior
Assembly
Exterior
Assembly
Interior Assembly
Mounting Plate
Screw A Screw C
Screw D
Strike
Screw B
Bolt Backup Key
AA Alkaline Batteries
May not be included
for some regions
Screwdriver User Guide Drill Template
Reset Needle Door Sensor
- 2 -
Packing List
Ultraloq U-Bolt Pro
User Guide
(V1.0)
Drill Template(V1.6)
Face of the door Edge of the door
Centerline
Backset
2
3
/
4
(70 mm)
2
3
/
8
(60 mm)
1
3
/
4
(44mm)
1
3
/
8
(35 mm)
Centerline
Backset
2
3
/
4
(70 mm)
2
3
/
8
(60 mm)
1
3
/
4
(44mm)
1
3
/
8
(35 mm)
Fold
(V1.6)
Plantilla de Perforación
Cara de la puerta Borde de la puerta
Eje
Cara de la puertaBorde de la puerta
Eje
Doblar
Entrada de
la cerradura
Entrada de
la cerradura
Fold
Doblar
Drill Template(V1.6)
(V1.5)
Plantilla de Perforación
Face of the doorEdge of the door
2”(50mm)
2”
(50mm)
Screw F
Screw E
Please scan this QR code to watch the easy
step by step installation video before
attempting to install Ultraloq U-Bolt WiFi.
1”
25 mm
53 mm
2 1
/
8
(33 mm ~ 50 mm)
15
/
16
~
2 ”
2 3
/
4
2 3
/
8
(70 mm)
OR
(60 mm)
Installation Guide
Installation Video
- 3 -
1. Preparing Door
Check the doors dimensions.
Step 1
Measure to conrm that the door is between
15
/
16
~
2 ”
(33 mm-50 mm) thick.
Step 2
Measure to conrm that the diameter of the hole is
2 1
/
8
(53 mm)
Step 3
Measure to conrm that the backset is either
2 3
/
8 ” or 2 3
/
4
(60 mm or 70 mm) .
Step 4
Measure to conrm that the diameter of the hole in the door
edge is
1”
(25 mm).
Step 5
Measure to conrm the depth of the hole in the frame is at least
1''(25mm).
If you have a new door, please drill the holes according to Drill
Template.
Or you can also view the webiste directly.
www.u-tec.com/lock/U-bolt-WiFi/guide
1''(25mm)
- 4 -
2. Installing Bolt and Strike
2
3
/
8
2
3
/
4
Adjust the Bolt
basket length
Step 1
Install Bolt into the door. Make sure the UP icon goes up.
Step 2
Note: Bolt is set for
2 3
/
8
backset initially. It can be adjusted to
2 3
/
4
if needed.
To adjust it please make sure the bolt is retracted, then, press it, twist and pull it
or push it to your desired length.
Install Strike into the door frame.
- 5 -
Step 1
Keep Bolt retracted and the cylinder tailpiece horizontal.
Install Exterior Assembly. Please do not insert the mechanical key
during installation .
Step 2
Align its two sticks with two holes on Bolt. The cable goes through
the hole below Bolt.
3. Installing Exterior Assembly
Step 1
Route the cable through the hole on Interior Assembly Mounting
Plate.
Step 2
Secure Interior Assembly Mounting Plate to Exterior Assembly
using Screws D.
4. Installing Interior Assembly Mounting Plate
- 6 -
5. Installing Interior Assembly
Step 1
Remove the battery cover of the Interior Assembly.
Step 2
Insert the connector of the cable to the socket on Interior
Assembly. Press the connector in rmly until it is completed
seated.
Screw D
- 7 -
Step 3
Rotate the knob and keep it in a vertical position to stay
unlocked.
Step 4
Attach Interior Assembly to Mounting Plate and tighten 2 Screws E.
6. Installing the Batteries and Performing the Door
Handing Process
This step will teach your lock the orientation of your door and is
crucial to lock operation.
Unlocked
- 8 -
Step 1
Rotate the knob and keep it in a horizontal position to stay locked.
Step 2
Insert 4 AA Alkaline Batteries.
Step 3
Install battery cover.
Locked
Note: Any ngerprint or code can unlock U-Bolt Pro WiFi in Factory Default Mode.
7. Installing the Door Sensor(Optional)
The door sensor lets you know whether the door is open or closed
through the App. When the auto lock is enabled in the App, your
Ultraloq will only lock itself when the door is closed.
Please do not mount the door sensor on the kind of metal door
that interferes with the magnet inside the door sensor(In this case,
the door sensor sticks to the metal door magnetically).
The door sensor can be installed on the wooden door or the kind
of metal door that will not interfere with the door sensor(In this
case, the door sensor will not stick to the door magnetically).
- 9 -
Note: Please refer to the guide in U-tec App for more information.
Door
Frame
Option 1 Installing with Sticker
Peel o either side of the sticker and push it against the door
frame about 10s. Peel o the other side and secure the door
sensor on the sticker rmly. Put on the door sensor cover at last.
Option 2 Installing with Screw F
Push the door sensor against the wall and secure it with Screw F.
You may need to drill a hole rst if the door frame is hard to screw
in with Screw F directly. Put on the door sensor cover at last.
UP
Door
Frame
UP
Door
Frame
Door
Frame
NoteDoor sensor should be
mounted as close to the edge
of your door frame as possible
,or within 0 to 1''(25 mm) from
the edgeand as close to the
bottom of the extended
deadbolt as possible ,or within
0 to 1''(25 mm) from the edge.
1. Product Overview
Anti-peep Keypad
Used to enter the code and unlock from outside.
Backup Key Hole
Used to insert the key to unlock in emergency situations.
Ultraloq Button
Used to lock from the outside, illuminate the keypad for code
entry and conrm previous operation etc.
Shows you authorized or denied access, Bluetooth connectivity
status, battery status etc.
- 10 -
Please watch our easy step by step User Guide video before
attempting to use your Ultraloq U-Bolt WiFi Smart Lock.
User Guide
User Guide Video
Or you can also view the webiste directly.
www.u-tec.com/lock/U-bolt-WiFi/guide
Anti-peep Keypad
Ultraloq Button
Backup Key Hole
- 11 -
Reset Button
Used to reset the lock to Factory Default settings.
Battery Compartments
Used to insert 4 AA alkaline batteries.
Note: Lithium batteries may have a longer life, but when
they begin to fail, they fail quickly. We don’t recommend
them because they don’t give you a lot of time to change
your batteries before the lock is completely dead.
Please don't use any Rechargeable Battery.
Battery Cover
Used to cover batteries and product label.
Knob
Used to unlock and lock the door from inside.
LED Indicator
Turns red when door is unlocked.
1.3 Low Battery Alarm
There will be low battery alert on the lock and App when battery
is low. Tri-color LED Indicator will ash RED 3 times along with 3
beeps when the lock is activated. Please replace batteries.
1.2 Interior
Reset Button
Battery
Compartments
Battery Cover
Knob
LED Indicator
- 12 -
Step 1
Scan above QR code to download the App, or search “U-tec”in
App Store (iOS) and Google Play (Android).
Step 2
Open the App, register U-tec account and log in the account.
Step 3
Make sure the lock is in Factory Default Mode. Turn on Bluetooth
on your smartphone, stay near the lock (within 10 feet ) and
search the lock in the App.
Step 4
Pair the lock in the App and start to use it.
DON’T WANT TO USE THE APP?
Please go to page 14 for programming guide for Standalone
Mode.
2. Lock Setup
Note: Please refer to the guide in U-tec App for more information.
App
3. Using Your Lock
• User Code
• Smartphone
Use your smartphone to unlock. Please refer to the guide
in U-tec App.
3.1 Unlock From Outside
Enter 4-8 digit code and press Ultraloq Button to unlock .
Note: You can press Ultraloq Button to turn on Keypad backlight.
U-Bolt
3.2 Lock From Outside
Press Ultraloq Button to lock manually.
Enable Auto Lock feature and the lock will relock automatically.
3.3 Unlock From Inside
Rotate the knob to a vertical position to unlock.
- 13 -
- 14 -
3.4 Reset the Lock
Please note all data will be erased if you reset U-Bolt WiFi to
factory default. If you are using U-tec App as Owner, please click
“Delete and Reset” to remove the lock from your U-tec Account,
then use a Reset Needle to push the Reset Button (at the bottom
of Interior Assembly) for around 3 seconds until you hear one long
beep and two short beeps.
3.5 Replace Batteries
Please use 4 high-quality alkaline AA batteries for replacement
when the battery is dead.
3.6 Emergency Key Override
Emergency Key Override can be used when the battery is dead.
1:
2:
3:
1 2 3 4 5 6 X X X X X X
1 2 3 4 5 6
X X X X X X
1 2 3 4 5 6
X X X X X X
Example
User Code: 123456
Vague Code
3.7 Enable Or Disable Auto Lock
Enable
Please keep Bolt unlocked and press "1" button for 3 seconds until
LED turns green and "1" button blinks.
Disable
Please keep Bolt unlocked and press "0" button for 3 seconds
until LED turns green and "0" button blinks.
This can also be set in U-tec App and Auto Lock timing can be
programmed between 10 seconds to 5 minutes. Factory Default
timing is 30 seconds.
3.8 Anti-peep Keypad
The lock supports up to 16-digit Vague Code. Just enter any
16-digit code, as long as a correct code is included in what you
entered, you can open the door.
Important Note
Please keep at least one key in secure location outside of
your place.
- 15 -
4.2 Add User Code in Standalone Mode
IndicatorOperation
Hold for 3 sec 2 beeps with ashing
blue light
Enter 4-8 digit Admin Code
and press
2 beeps with green light,
then steady blue light
Warning
Standalone Mode is NOT available after the lock is registered
in App! Please reset the lock to Factory Default Mode rst to
program your lock in Standalone Mode.
Admin Code must be created rst prior to any other programming.
Only one Admin Code is available.
4. Standalone Mode Programming Guide
IndicatorOperation
4.1 Add Admin Code in Standalone Mode
Hold for 3 sec 2 beeps with ashing
green light
Enter 4-8 digit Admin Code
and press
1 beep with green light,
then ashing green light
Enter the Admin Code again
and press 2 beeps with green light
Success All lights o
It is recommended to use U-tec App to program your lock. If
you don’t have a smartphone or don’t want to use the App, you
can use the programming instructions below.
- 16 -
4.3 Delete Admin and User
Please reset the lock to Factory Default Mode to delete Admin
and all Users.
How to reset the lock in Standalone Mode?
Please use a Reset Needle to push the Reset Button (at the
bottom of Interior Assembly) for around 3 seconds until you hear
one long beep and two short beeps.
FAQ
Enter 4-8 digit User Code
and press 1 beep with green light,
then steady blue light
2 beeps with green light
Success All lights o
Enter the User Code again
and press
1. How to reset U-Bolt WiFi?
Please note all data will be erased if you reset U-Bolt WiFi to
factory default.
If you are using U-tec App as Owner, please click “Delete and
Reset” to remove the lock from your U-tec Account, then use a
Reset Needle to push the Reset Button (at the bottom of Interior
Assembly) for around 3 seconds until you hear one long beep and
two short beeps.
If U-Bolt WiFi is working as Standalone Mode, please use a Reset
Needle to push the Reset Button (at the bottom of Interior
Assembly) for around 3 seconds until you hear one long beep and
two short beeps.
- 17 -
2. What if I lost the paired smartphone?
Please go to www.u-tec.com/myutec.html or login U-tec App via
another smartphone to change your U-tec Account password.
3. How can I unlock U-Bolt WiFi if battery runs out?
There will be low battery alert on the lock and App when battery
is low. Red LED will ash 3 times along with 3 beeps when the lock
is activated. Please replace batteries.
If battery runs out, you can use the backup key to unlock.
4. What’s the dierence between Owner, Admin, Normal
User and Temporary User?
Owner is the person who owns U-Bolt WiFi and registers it in U-tec
App originally. Owner has all privileges.
Admin can always unlock via code or App. Admin can add or
delete Admin and Users, control all lock settings and view logs.
Normal User can always unlock via code or App. Temporary User
has limited access within specic time range.
5. Does U-Bolt WiFi work with accessories such as bolt
from third party?
It is recommended to use the original accessories for best
performance and stability.
6. What is the user capacity for U-Bolt WiFi?
U-Bolt WiFi supports maximum 60 users and each user can
register 1 code.
7. What is the log capacity for U-Bolt WiFi?
U-Bolt WiFi supports maximum 1000 logs. The latest log will
replace the oldest one once log is full.
8. How to extend battery life of Ultraloq U-Bolt WiFi?
You can disable the Remote Access to Lock function in the U-tec
APP. After turning o the Remote Access to Lock function,battery
life will be approximately doubled.
Remote operation,smart control such as Alexa,Google
Assistant,IFTTT and smart notications will all be unavailable if
turned o.
9. Does Ultraloq U-Bolt WiFi need to be paired with an
Ultraloq Bridge?
No, it is a smart lock with built-in WiFi. No extra hub required.
10. What is the network requirement?
U-Bolt WiFi can only work with the 2.4G WiFi network (5G WiFi
NOT supported).
Ultraloq U-Bolt WiFi
Guía de Instalación y Uso
(V1.0)
ESPAÑOL
Para asegurar el mejor servicio, por favor registra tu cuenta en
www.u-tec.com/register.html
¿Necesitas Ayuda?
Para documentos técnicos y más
por favor visita www.u-tec.com/support
Email: support@u-tec.com
Notas Importantes
Declaraciones
- 1 -
Antes de usar cualquier producto Ultraloq, por favor lea todos
los términos, reglas, políticas, y disposiciones de uso aplicables
que podrá encontrar en www.u-tec.com/company/privacy.
Usando su Ultraloq, usted acepta estar sujeto a la Política de
Privacidad de U-tec.
Términos y Políticas de Ultraloq
• No uses un taladro electrónico para Instalación.
• Instala y prueba la cerradura con puerta abierta para evitar
ser bloqueada.
• Por favor lee todas las instrucciones antes de contactar al
apoyo de clientes.
• Por favor contacta al apoyo de clientes antes de
devolver el producto a la tienda.
• No instales las baterías antes de instalar la cerradura! ¡Sigue las
instrucciones en orden secuencial!
• Esta cerradura es diseñada para las siguientes
temperatura de operación:
Parte Exterior: -31˚F (-35˚C) a 158˚F (70˚C)
Parte Interior: -14˚F (-10˚C) a 131˚F (55˚C)
• Por favor, use batería alcalina AA y no use batería de litio o
batería recargable.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38

U-tec B086DR2CZX Ultraloq U-Bolt WiFi Smart Lock User guide

Type
User guide
This manual is also suitable for

U-tec U-tec B086DR2CZX Ultraloq U-Bolt WiFi Smart Lock offers keyless convenience and enhanced security for your home. With its anti-peep keypad and smartphone compatibility, you can unlock your door using personalized codes or the U-tec App. The auto-lock feature ensures your door is always securely locked, and the low battery alarm alerts you when it's time for a change. Plus, the emergency key override provides peace of mind in case of battery failure.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI