Commercial Electric PRWX50-H-PC-4K-BZ User guide

PRWX50-H-PC-4K-BZ
Brand
Commercial Electric
Model
PRWX50-H-PC-4K-BZ
Type
User guide

This manual is also suitable for

Model No. PRWX50-H-PC-4K-BZ
PRWX80-H-PC-4K-BZ
POWERWALL X
LED WALLPACK
USE AND CARE GUIDE
THANK YOU
We appreciate the trust and confidence you have placed in Commercial Electric through the purchase of this LED
flood light. We strive to continually create quality products designed to enhance your home. Visit us online to see our
full line of products available for your home improvement needs. Thank you for choosing Commercial Electric!
Questions, problems, missing parts? Before returning to the store,
call Commercial Electric Customer Service
8 a.m. - 7 p.m., EST, Monday – Friday, 9 a.m. – 6 p.m., EST, Saturday
1-877-527-0313
HOMEDEPOT.COM
2
Table of Contents......................... 2
Safety Information....................... 2
Pre-Installation.............................. 4
Planning Installation...................... 4
Specifications.................................... 4
Tools Required................................. 4
Package Contents............................ 5
Hardware Included........................... 5
Installation.................................... 6
Operation...................................... 12
Care and Cleaning........................ 13
Troubleshooting........................... 13
Warranty.......................................... 3
Table of Contents
Safety Information
IMPORTANT
This product must be installed in accordance with the applicable National Electrical
Code and local building codes by a person familiar with the construction and operation
of the product and the hazards involved.
PRECAUTIONS
Please read and understand this entire
manual before attempting to assemble,
install, or operate this light fixture.
This light fixture requires a 120-277 volt
AC power source.
Some codes require installation by a
qualified electrician.
This light fixture must be properly
grounded.
Make sure connections are secure
using wire nuts, crimp-on lugs or other
approved connecting devices.
This light fixture should be installed
outdoors on a wall.
WARNING: Before installation or servicing, turn
the power off at the circuit breaker or fuse. Place
tape over the circuit breaker switch and verify
power is off at the light fixture.
WARNING: Risk of fire. Keep the lamp heads
at least 3 in. (76 mm) from combustible
materials.
CAUTION: Burn hazard. Allow the light fixture
to cool before touching.
NOTE: For dimming, use a 0-10 volt
dimming switch
NOTE: FCC Regulations state that any unauthorized
changes or modifications to this equipment not
expressly approved by the manufacturer could void
the user’s authorization to operate this equipment.
INFORMATION: The device is tested and found to comply with Part 15 of the FCC Rules. Operation is subject to two
conditions: (1) This device may not cause harmful interference and, (2) this device must accept any interference received,
including any interference that may cause undesired operation. This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment. The equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of the equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense.
☐
☐
☐
☐
☐
☐
3
Warranty
This is a limited warranty offered by Commercial Electric for a period of five years from the date
of purchase to its customers. Commercial Electric warrants to customers that the products
will be free from defects in material and workmanship. The obligation of Commercial
Electric under this warranty is limited to the provision of replacement of products and is
extended to the original purchaser of the product on presenting valid purchase receipt or other
proof of date of original purchase acceptable to Commercial Electric. The receipt is
required for rendering the warranty performance. Any warranty claims without original proof of
purchase would not be accepted.
It should be noted that the warranty does not apply to Commercial Electric products that have
been altered or repaired by unauthorized personnel, have been subjected to neglect,
abuse, misuse or accident or damages caused during shipping. Any other products not
manufactured by Commercial Electric which have been supplied, installed and/or used in
conjunction with Commercial Electric products are not covered under this warranty. Any
damages caused by replacements bulbs, LEDs or corrosion or discoloration of brass
components are also not covered by this warranty.
LIMITATION OF LIABILITY
In no event Commercial Electric shall be liable for indirect, consequential, incidental or special
damages, or lost profits. Commercial Electric is not liable for any claims or damage arising out
of or connected with the manufacture, sale, delivery, use, maintenance and repair or modification
of Commercial Electric products, or supply of any replacement parts that exceed the purchase
price of Commercial Electric products giving rise to a claim. Labor charges to remove or install
the fixtures will not be accepted.
TO CLAIM
Please contact Commercial Electric customer service at 1-877-527-0313 or email
[email protected] and include your name, address and contact number, along
with a copy of the purchase receipt and a brief description of the problem.
HOMEDEPOT.com
Please contact 1-877-527-0313 for further assistance.
4
Pre-Installation
Lumens (Light Output) 6,500 Lumens 10,000 Lumens
80 Watts LED
650W Incandescent
125 Lumens per watt
Watts (Power Consumption) 50 Watts LED
Replaces 450W Incandescent
Lumens/Watts (Efficacy) 130 Lumens per watt
Power Requirements
(Input Voltage) 120-277 VAC
Light Color (CCT) 4,000 Kelvin (Bright White)
Dimmable Dimming (When used with a 0-10V dimming switch.)
Operating Modes Dusk-to-Dawn:
Automatically turns light fixture ON during night
and OFF during day.
Switch-Controlled:
Flip switch to turn light fixture ON and OFF. (Use
included light sensor cap on fixture's light sensor
to utilize this mode setting).
PLANNING INSTALLATION
Before installing the light fixture, ensure that all parts are present. Compare parts with the
Hardware Included and Package Contents sections. If any part is missing or damaged, do
not attempt to assemble, install, or operate this light fixture.
SPECIFICATIONS
TOOLS REQUIRED
Phillips
screwdriver
Wire strippers/
cutters
Circuit tester
Safety
goggles
Work
gloves
Silicone
sealant
Ladder
Power drill
5
Pre-Installation (continued)
HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.
AA BB
Part Description Quantity
AA #8-32 x 3/4 in. Phillips head screw 2
BB Wire nut 3
CC Hex head screwdriver 1
CC
Clear photocell cover cap
PACKAGE CONTENTS
Part Description Quantity
ALight fixture 1
B
Mounting plate tightening screw (pre-installed) 1
Conduit entry knock-out feature 2
C
DPhotocell black opaque cap cover 1
E
F
Leveling bubble 1
Mounting plate 1
E
F
A
D
C
B
DD
HOMEDEPOT.com
Please contact 1-877-527-0313 for further assistance.
6
Pre-Installation (continued)
Installation
Wall Mount
1-1/2 in. 1-1/2 in.
Round Octagonal/Square
NOTE: Mounting base (D) mounts to recessed
mounted standard junction boxes or to the surface
directly. Junction box must be at least 1-1/2 inch
in depth for proper installation for recessed
mount application (fig 1).
(fig 1).
The fixture can be mounted in the
following two ways:
˜Junction Box Mount: Use a junction
box to mount the fixture.
˜Surface Conduit Mount: The fixture
can also be mounted directly on the
wall surface using conduit entry.
When mounting fixture, for Dusk
to Dawn operation, make sure the
photocell orientation is at the top for wall
mount, in an area that receives daylight
and not too close to reflective surfaces.
When installing two fixtures on one
switch, make sure the switch is rated for
at least a 1A inductive load.
If dimming, use with 0-10V dimming
switch.
1Shut off electric power
Verify wall switch is in OFF position (fig 2).
the circuit breaker that supplies power
At the main electrical panel, turn off
to the junction box you are working on
(fig 3).
For screw-in type fuses, unscrew the
fuse that supplies power to the junction
box you are working on (fig 4). (fig 2). (fig 3). (fig 4).
☐
☐
☐
☐
☐
☐
☐
7
Installation (continued)
2Removing the
Mounting Plate
Loosen the mounting plate tightening screw (C)
using a hex head screwdriver (CC) and
remove the mounting plate (F) from the
fixture. (fig.5)
3Installing the
Mounting Plate
(fig 6).
FOR MOUNTING TO A JUNCTION BOX
Route the junction box wires through
the large center hole in the mounting
plate (F).
Align the holes on the mounting plate
(F) with the holes on your junction box.
Use two #8 screws (AA), depending
on the size of the holes in your junction
box, to attach the mounting plate (F) to
your junction box. (fig.6)
NOTE: Use the leveling bubble (E) inside the
mounting plate (F) to adjust mounting for a
level install.
F
AA
F
C
CC
(fig 5).
NOTE: The mounting plate tightening screw (B)
comes pre-installed on the light fixture.
The tightening screw should not be
completely removed.
E
HOMEDEPOT.com
Please contact 1-877-527-0313 for further assistance.
☐
☐
☐
Installation (continued)
8
4Making Electrical
Connections
If necessary, strip 3/8 in. of insulation from
junction box and lighting fixture wires (fig 7).
Affix the fixture hands-free hanging wire
hook (the metal cable found on the back of
the fixture) to the small U-shaped slot
located on the bottom of the mounting plate
(F) (fig 8). This hanging wire allows the fixture
to hang in place while freeing both hands for
your electrical connections.
(fig 7).
Hanging wire hook for
hands-free electrical wiring
F
(fig 8).
NOTE: Use the leveling bubble (E) inside
the mounting plate (F) to adjust mounting for
a level install.
WHEN DIRECT SURFACE MOUNTING
USING SIDE CONDUIT ENTRY WIRING
(No junction box present)
Mark and drill two to four holes on the
wall surface as per the desired location
for attaching the mounting plate (F).
Use two or more suitable screws (not
included) to attach the mounting plate
(F) to the surface. (fig 9)
(fig 9).
F
E
AA
☐
☐
☐
☐
(fig 10).
Remove the conduit entry knock-out (B)
on the sides of the light fixture (A).
Thread the wires through the conduit entry
on the mounting plate (F) as shown in fig
10. Secure the conduit to the mounting
plate (F) and make wire connections as
shown in fig 10.
Hang light fixture (A) on mounting plate (F).
Tighten the mounting plate tightening
screw (C) to secure light fixture to the
mounting plate (F).
WHEN USING SIDE CONDUIT ENTRIES
(No junction box present)
Installation (continued)
9HOMEDEPOT.com
Please contact 1-877-527-0313 for further assistance.
F
A
B
C
CC
☐
☐
☐
☐
(Non-Dimming Wiring Diagram)
Surface Conduit Mount
Junction Box Mount
(0-10V Dimming Wiring Diagram)
10
Installation (continued)
Connect lighting fixture black wire to
junction box black wire (line), lighting fixture
white wire to junction box white wire
(common), and the lighting fixture green
wire to the junction box ground wire (fig 11).
For the purple and gray fixture wires either
leave the wires unstripped or individually
terminate fixture’s purple and gray wires
with wire nuts to prevent shorting (fig 11).
NOTE: Leave purple and gray wires terminated and
separated when NOT connecting to a 0-10V dimmer.
DO NOT connect the purple and gray wires to any
other wire unless wiring to a 0-10V dimmer.
FOR NON-DIMMING ELECTRICAL WIRING
(Follow these steps when NOT wiring
to a 0-10V dimmer).
TIP: Hold stripped ends near each other and align
any frayed strands (do not twist wires). Push the wires
into wire nut (BB) and use your fingers to twist the
wire nut clockwise until tight. Check for
tightness by pulling wires.
Black
(Line)
White
(Common)
Green
(Ground)
Junction
Box
Gray (-)
Dimming
Purple (+)
Dimming
Non-Dimming Wiring Diagram (fig 11).
Follow this diagram when NOT wiring
to a 0-10V dimmer.
Black
(Line)
Purple (+)
Dimming
Gray (-)
Dimming
White
(Common)
Green
(Ground)
0-10V
Dimmer
Connect lighting fixture black wire to
junction box black wire (line), lighting fixture
white wire to junction box white wire
(common), and the lighting fixture green
wire to the junction box ground wire.
For dimming, when connecting to a 0-10V
dimmer, connect the lighting fixture purple
wire to the dimmer switch purple wire
(+ DIM) and the lighting fixture gray wire to
the dimmer switch gray wire (- DIM) (fig 12).
FOR ELECTRICAL WIRING TO 0-10V DIMMER
(Follow these steps when wiring to a 0-10V dimmer.)
Dimming Wiring Diagram (fig 12).
Follow this diagram when wiring to a
0-10V dimmer.
☐
☐
☐
☐
(fig 13).
Once electrical connections are complete,
push wires and connections into the junction
box and hang the fixture by attaching the
back of the fixture to the mounting plate (F).
Tighten the one mounting plate tightening screw (C)
to secure fixture to the mounting plate (F). (fig. 13)
Installation (continued)
5Mounting the Light Fixture
6Caulking Around the
Light Fixture
NOTE: Failure to properly caulk around the
back face of the light fixture and mounting
surface could lead to water damage and is not
covered under warranty.
NOTE: When attaching this light fixture to an
extruded surface mount junction box, caulk
between the junction box and the mounting plate.
Caulk around the back face of the light fixture
as shown in fig 14 with silicone sealant (not
included).
(fig 14).
11HOMEDEPOT.com
Please contact 1-877-527-0313 for further assistance.
F
C
CC
☐
☐
☐
12
Operation
To enable dusk-to-dawn operation, remove the
black opaque cap cover (D) installed
on the fixture. Note: Ensure the
photocell is unobstructed. (fig 15)
Ensure the switch powering the outlet
connected to the light fixture is turned
to the ON position and leave it ON
at all times to enable dusk-to-dawn
functionality to operate automatically.
NOTE: If photocell is located in an area
under heavy shade, the photocell may not
detect enough light and may turn the light
fixture on.
TIP: To test if the light fixture and photocell
work properly, run power to the fixture and
cover the photocell to turn fixture ON.
Shine a light into the photocell to see if
fixture turns OFF.
AUTOMATIC
NIGHTTIME ON
DAYTIME OFF
Selecting Dusk-to-Dawn or Switch-
Activated Control
OPTION 1: DUSK-TO-DAWN OPERATION
Dusk-to-dawn operation enables the light fixture to automatically turn
ON when dark outside and turn OFF when the sun rises, thus saving
you energy.
OPTION 2: SWITCH CONTROLLED
Switch controlled operation enables the light fixture to
turn ON and OFF by flipping a switch that controls the
electricity to the outlet powering the fixture. The light
fixture will not turn ON and OFF automatically, but is
manually controlled.
To enable switch activated
operation leave the black cap cover
(D) on the photocell.
(fig 16).
(fig 15).
(fig 16).
D
D
☐
☐
☐
appearance, clean the light fixture with clear water and a soft, damp cloth only.
Do not use abrasive cleaners or cleaners that contain alcohol. Do not apply paints,
solvents, or any other chemicals on this light fixture. They could cause a premature
deterioration of the finish and may void the warranty.
Do not spray the light fixture with a hose or power washer.
Care and Cleaning
Troubleshooting
Problem Possible Cause Solution
Light does not
turn ON
No power to the fixture
Check if circuit breaker is tripped.
Confirm wall switch is ON.
Verify wiring to fixture is correct (turn
Fixture is sensing daylight Cover photocell. Wait several
seconds until fixture turns ON.
Light cycles
ON and OFF
continuously
Photocell light sensor is
sensing reflected light
Relocate light fixture to a location
where there is no reflected light.
OR place the black cap cover
over the photocell and use the wall
switch to turn the light fixture
ON and OFF.
Light
FLICKERS
The light fixture is wired
through an unsuitable dimmer
Replace the dimmer with a 0-10V
dimming switch or a standard
ON/OFF wall switch.
Light stays ON
Photocell is in a shaded area
Shine a flashlight into the photocell
and wait a couple minutes.
If the light turns OFF, the fixture
should be moved to a location
with enough light in the daylight
hours for the photocell to work.
OR place the optional opaque
cover over the photocell
and use the wall switch to
turn the light ON and OFF.
Photocell is faulty
a flashlight is shone on the photocell
for a few minutes, then the photocell
may be faulty. Please contact
customer service.
NOTE: Photocell may have a few minutes delay during troubleshooting.
When testing, shine a light and/or cover the photocell and allow a few minutes
for fixture to function properly.
13HOMEDEPOT.com
Please contact 1-877-527-0313 for further assistance.
☐
☐
☐
Questions, problems, missing parts? Before returning to the store,
call Commercial Electric Customer Service
8 a.m. - 7 p.m., EST, Monday – Friday, 9 a.m. – 6 p.m., EST, Saturday
1-877-527-0313
HOMEDEPOT.COM
Retain this manual for future use.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

Commercial Electric PRWX50-H-PC-4K-BZ User guide

PRWX50-H-PC-4K-BZ
Brand
Commercial Electric
Model
PRWX50-H-PC-4K-BZ
Type
User guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents