LIGHTINOVA CLIXX is a versatile magnetic track lighting system that offers endless possibilities for creating customized lighting solutions. With its sleek design and easy installation, CLIXX is perfect for both residential and commercial applications. The system's magnetic connectors allow for quick and tool-free installation, making it easy to add or remove lights as needed. CLIXX is available in a variety of track lengths, colors, and configurations, so you can create a lighting system that is tailored to your specific needs.
LIGHTINOVA CLIXX is a versatile magnetic track lighting system that offers endless possibilities for creating customized lighting solutions. With its sleek design and easy installation, CLIXX is perfect for both residential and commercial applications. The system's magnetic connectors allow for quick and tool-free installation, making it easy to add or remove lights as needed. CLIXX is available in a variety of track lengths, colors, and configurations, so you can create a lighting system that is tailored to your specific needs.
CLIXX
MAGNETIC
TRACK SYSTEM
INSTALLATION INSTRUCTIONS
ATTENTION
Installation instructions attention
The safety of this product can only be guaranteed if the installation
instructions are respected and carried out by a qualied professional.
Warning:
Always disconnect the power before installation. Do not attempt to make
any modications on the products. Lightinova declines any responsibility
on modied products. Installation should be carried out by a qualied
professional. It is recommended to test products before installation,
especially with recessed products. The LED driver should always be
accessible. This product is designed for indoor installation.
If any steps in the installion instructions are unclear, please contact us:
tel. +31 (0) 76 369 00 24
e-mail [email protected]
www.lightinova.com
2
Connecting tracks (surface/suspended) Page 4 - 5
Connecting corners (all installations) Page 6
Connecting track driver box (all installations) Page 7
Wiring (all installations) Page 14 - 15
CONTENTS
3 I CLIXX
LIGHTINOVA.COM
Surface installation
Page 8-9
Recessed installation
Page 10-11
Suspended installation
Page 12-13
4
Place track on a at clean surface.
Remove the magnet that supports the
decorative board with a screwdriver.
Remove the end caps with the included
hex key or screwdriver.
Slide ‘pins’ into ‘powerplate’.
CLIXX SLIM: 2 x pin-2 for all dimming types
CLIXX regular: pin-3 for TRIAC, 2 x pin-2 for
1-10V and DALI.
Lift and remove the ‘decorative board*’ from
the magnet.
* The ‘decorative plate’ should only be removed when connecting both sides of the track. If only 1 side of the track is connected,
choose the side without the plate, which can be connected directly with ‘pins’.
Insert the ‘powerplate’ into the track, make
sure the pins connect correctly.
1. CONNECTING TRACKS (SURFACE AND SUSPENDED INSTALLATION)
1
4
2
5
3
6
5 I CLIXX
The track is now prepared for electrical
connection.
Tighten the included screws until the track
connector is xed into place.
Turn the track around.
Slide both the ‘track connector’ and ‘pins’ into
the second track, connecting tracks and
electrical circuit. Make sure the pins connect
with the terminal block.
Slide the ‘track connector’ into the rst track.
Tighten the included screws until track
connector is xed into place.
7
10
8
11
9
12
LIGHTINOVA.COM
6
Slide ‘pins’ into board.
CLIXX SLIM: 2 x pin-2 for all dimming types
CLIXX regular: pin-3 for TRIAC, 2 x pin-2 for
1-10V and DALI.
Slide both the ‘track connector’ and ‘pins’ into
the second track, connecting tracks and
electrical circuit. Make sure the ‘pins’ connect
with terminal block.
Turn the track around.
Tighten the included screws until track
connector is xed into place.
Slide the ‘track connectors’ into the corner
prole and tighten screws until xed.
Repeat these steps for the other end(s).
2. CONNECTING CORNERS (ALL INSTALLATIONS)
1
4
2
5
3
6
7 I CLIXX
Connect cable to driver box (L/N/PE). The
driver box is available for all installation types.
Slide both the ‘track connector’ and ‘pins’
into the track, connecting tracks and electrical
circuit. Make sure the ‘pins’ connect with the
terminal block in the track.
Attach the end cap to the driver box. Note that
the driverbox is located at the start/end of the
track system or when connectable at both ends
in the middle.
Tighten the included screws until ‘track
connector’ is xed into place.
Slide the ‘track connector’ into the ‘driver box’
and tighten screws until xed.
The driver box is available for all installation
types. Note that the recessed driver box is
different. There is also a driverbox available
that can be connected at both ends and
placed in the middle.
3. CONNECTING TRACK DRIVER BOX (ALL INSTALLATIONS)
1
4
2
5
3
6
LIGHTINOVA.COM
8
4. SURFACE INSTALLATION
Decide position of track and mark position of
mounting clips. Detailed instructions on next
page.
For electrical connection and wiring go to page 14-15
Turn the levers tight until track is xed into
place.
Fix mounting clips to ceiling. Use plugs and
screws suitable for the specic ceiling type.
Make sure clips are aligned with the track.
Place the track over the mounting clips, leaving
the levers exposed.
7
10
8
11
9
12
9 I CLIXX
LIGHTINOVA.COM
Mounting of connected 2 meter tracks
Each 2 meter track requires 2 mounting clips. The dimensions given above are indicative. Corner proles and driver boxes are
supported by the track connectors and do not require any mounting clips. Make sure to use a clip near where the tracks are
connected if you notice that the track connector alone does not give enough support.
A stand alone 1 meter track requires 2 mounting clips. For connected tracks 1 mounting clip is sufcient. Corner proles are
supported by the track connectors and do not require any mounting clips. Corner proles and driver boxes are supported by
the track connectors and do not require any mounting clips. Make sure to use a clip near where the tracks are connected if
you notice that the track connector alone does not give enough support.
Mounting of connected 1 meter tracks
350 350350 350
200
1300 1300
600 700 1000 1000
10
5. SUSPENDED INSTALLATION
Decide position of track and mark pendant
clips. 2 for 1m and 2m track.
Turn the suspension brackets until straight side
of bracket is positioned under track exposing
the screw holes.
Attach the ceiling rose (A) over the central box
and suspension brackets (B) to the ceiling.
Use plugs and screws that are suitable for the
specic ceiling type.
Fix suspension brackets into place with
included hex socket set.
Place the tracks over the brackets. Connect the
power cable on top of the track (between the
sliders) or to the driver box or input terminal.
(See page 15)
- To shorten wire pull wire at end
- To extend wire push the top and pull wire up
7
10
8
11
9
12
Ga voor elektrische aansluiting en bedrading naar pagina 14-15
11 I CLIXX
LIGHTINOVA.COM
Mounting of connected 2 meter tracks
A stand alone 2 meter track requires 2 mounting clips. For connected tracks 1 bracket is sufcient. The dimensions given
above are indicative. Corner proles and driver boxes are supported by the track connectors and do not require any brackets.
Make sure to use a brackets near where the tracks are connected if you notice that the track connector alone does not give
enough support.
A stand alone 1 meter track requires 2 suspension brackets. For connected tracks 1 bracket is sufcient. Corner proles and
driver boxes are supported by the track connectors and do not require any brackets. Make sure to use a bracket near where
the tracks are connected if you notice that the track connector alone does not give enough support.
Montage van aangesloten 1 meter tracks
350 350
500
1300
1000 1000 1000
12
Place tracks on a at clean surface.
Insert the track into the cut-out (ceiling/wall).
Remove the end caps with the included hex
key.
Use drywall screws (preventing rust) to x the
track in place. Wooden boards are recom-
mended as support. Make sure screws do not
protrude and to not distort the track.
No pins are required for connection of the
electrical circuit between tracks, only use pins
to connect corner proles.
Prepare the next track following the previous
steps.
6. RECESSED INSTALLATION
1
4
2
5
3
6
Connect cable(s) on top. 1 cable for TRIAC and
0-10V, 2 cables for DALI.
When the plaster is completely dry, apply paint.
Tracks are now connected and xed to the
ceiling. Always test system with LED module
before applying the plaster!
Apply the plaster.
7
10
8 9
LIGHTINOVA.COM
13 I CLIXX
14
7. WIRING
DC24V-
230V
N
L
24V-
24V+
CLIXX TRACK
DC24V+
DC24V-
230V
N
L
24V-
24V+
CLIXX TRACK
DC24V+
DALI
DA1
DA2
1-10V DIMMER
DC24V-
230V
N
L
24V-
24V+
DIM-
DIM+
CLIXX TRACK
DC24V+
TRIAC/ZIGBEE
Driver
Driver
Driver
DALI
1-10V
15 I CLIXX
LIGHTINOVA.COM
DC24V-
230V
N
L
24V-
24V+
CLIXX TRACK
DC24V+
DC24V-
230V
N
L
24V-
24V+
CLIXX TRACK
DC24V+
DALI
DA1
DA2
1-10V DIMMER
DC24V-
230V
N
L
24V-
24V+
DIM-
DIM+
CLIXX TRACK
DC24V+
A D G
B E
C F
Situation A, B, C
The driver is located inside the driver box. Only
in the case of DALI 2 wires should be guided
over the driver box to the track. L , N and
PE are automatically connected to the track
through the driver box.
Situation D
The driver is located inside the ceiling box.
Wires are connected on top of the track or
through the input terminal.
Situation E, F, G
The driver is located elsewhere. Make
sure the driver is accessible at all times.
Wires are connected on top of the
track or through the input terminal.
LIGHTINOVA.COM
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
LIGHTINOVA CLIXX is a versatile magnetic track lighting system that offers endless possibilities for creating customized lighting solutions. With its sleek design and easy installation, CLIXX is perfect for both residential and commercial applications. The system's magnetic connectors allow for quick and tool-free installation, making it easy to add or remove lights as needed. CLIXX is available in a variety of track lengths, colors, and configurations, so you can create a lighting system that is tailored to your specific needs.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
SKYDANCE DA-PS-L User manual
-
-
SKYDANCE DH User manual
-
FLOS Recessed Profile Installation and Use Manual
-
Whirlpool KUDE20FB*0 Product information
-
Aerohive HiveAP 20 Deployment Manual
-
Epson Ensemble HD 8100 User manual
-
luminii Retrac Installation guide
-
ETC Irideon FPZ User manual
-
