Kreator KRTGR9005 Owner's manual

Brand: Kreator

Model: KRTGR9005

Type: Owner's manual

  KRTGR9005  EN 
Copyright © 2018 VARO  P a g e  | 1  www.varo.com 
PARTS DESCRIPTION (FIG. A) ........................................................ 2 
GENERAL SAFETY RULES.............................................................. 2 
ASSEMBLY ........................................................................................ 2 
1  Figure 1 ...................................................................................................................... 2 
2  Figure 2 ...................................................................................................................... 2 
3  Figure 3 ...................................................................................................................... 2 
4  Figure 4 ...................................................................................................................... 3 
5  Figure 5 ...................................................................................................................... 3 
6  Figure 6 ...................................................................................................................... 3 
7  Figure 7 ...................................................................................................................... 4 
8  Figure 8 ...................................................................................................................... 4 
ADJUSTMENTS (FIG. 10) ................................................................. 4 
DECLARATION OF CONFORMITY .................................................. 5 
 
 
 
 
 
 
 
 
   
 

KRTGR9005 EN

SPREADER

KRTGR9005

1 PARTS DESCRIPTION (FIG. A)

1. Hex bolt M6x60 (2 pcs)

2. Hex bolt M6x50 (2 pcs)

3. Hex bolt M6x45 (3 pcs)

4. Hex bolt M6x40 (2 pcs)

5. Hex bolt M6x35 (4 pcs)

6. Hex bolt M5x45 (1 pc)

7. Screw M4x20 (1 pc)

8. Screw ST6.3x38 (4 pcs)

9. Lock nut M5 (1 pc)

10. Flat washer Ø6 (1 pc)

11. Lock nut M6 (13 pcs)

12. Handle spacer (1 pc)

13. Cotter pin Ø5x36 (2 pcs)

14. Axle bushing (2 pcs)

15. R pin (1 pc)

16. Flat washer Ø16 (5 pcs)

17. Wheel assembly frame (2 pcs)

18. Upper handles (2 pcs)

19. Handle shaft (1 pc)

20. Frame (1 pc)

21. Rain cover (1 pc)

22. Impeller (1 pc)

23. Connecting tube (1 pc)

24. Hopper screen (1 pc)

25. Wheel (2 pcs)

26. Hopper (1 pc)

27. Gear wheel and axle assembly (1 pc)

28. Adjustment and lever assembly (1 pc)

29. Frame brace (2 pcs)

2 GENERAL SAFETY RULES

▪ If your spreader does not spread evenly, be sure the FRONT on the gear points to the

front of the spreader. The impeller must turn clockwise. Reversing the gear will cause the

impeller to turn counter clockwise. Clean the impeller plate after each use. Fertilizer stuck

on the impeller blades will cause uneven spreading.

▪ Your spreader is designed to be pushed at about 5 km/h, which is a brisk walking speed.

Slower or faster speeds will change the spread patterns. Wet fertilizer will also change the

spread pattern and flow rate. Clean your spreader thoroughly after each use. Wash

between the cover plate and bottom of the hopper.

3 ASSEMBLY

3.1 Figure 1

Turn the hopper (26) upside down and attach the frame (20) using four screws ST6.3x38.

3.2 Figure 2

▪ Slide the impeller (22) onto the vertical shaft of the gear wheel and axle assembly (27).

▪ Insert the screw M4x20 (7) through the impeller and the top of the vertical shaft.

3.3 Figure 3

▪ Find the two wheel assembly frames (17) for mounting the wheels (25).

▪ Connect the right and left wheel assembly frames with the frame by using the bolts

M6X60, secure with a lock nut M6. Slip the gear wheel and axle assembly (27) with the

vertical axle pointing downwards into the central opening at the bottom of the hopper (26).

▪ Slip the left and the right wheel assembly frame (17) on the horizontal drive axle of the

gear wheel and axle assembly (27).

▪ Attach the left and the right wheel assembly frame (17) to the hopper frame (20) with the

bolts M6x20 (1) and the lock nuts M6 (11) in the bottom opening.

▪ Connect the two ends of the connecting tube (23) with the right and left wheel assembly

frames (17) by using bolts M6X40 (4), and secure them with a lock nut M6 (11).

▪ Connect the connecting tube with the shaft support plate by using a bolt M6X35, the big

flat washer Ø6 and the lock nut M6.

KRTGR9005 EN

3.4 Figure 4

▪ Connect the left and the right wheel assembly frames (17) to the hopper frame (20) by

using the frame braces (29) with 4 hex bolts M6x35 (5) and 4 M6 lock nuts (11).

▪ Attach one end of each frame brace to the outside of the hopper frame assembly by using

a bolt M6x35 and a M6 lock nut.

▪ Attach the other end of each frame brace to the inside of the left and right wheel assembly

frames by using a bolt M6x35 and a M6 lock nut.

NOTE: The nuts and bolts do not have to be completely tightened yet.

3.5 Figure 5

▪ First inflate the wheel tyres (2.0 bar).

▪ Slip the inner axle bushing (14) onto the right side of the axle, pushing the inner axle

bushing (14) into the collar of the plastic tube of the right wheel assembly frame until tight.

▪ Mount the drive wheel at the right side as follows: Slip the flat washer (16), the wheel (25)

and another flat washer (16) from the right side to the left side on the wheel axle. Turn the

wheel (25), until the boring hole at the inner side of the wheel aligns with the boring hole in

the wheel axle. Slide bolt M5x45 (6) through both boring holes. Fix this bolt with lock nut

M5. The wheel is secured in its position by means of a cotter pin. Push the cotter pin (13)

through the wheel axle. Bend the ends of the cotter pin (lower part) outwards to safely

secure the wheel.

▪ Slip the inner axle bushing onto the left side of the axle, pushing the inner axle bushing

into the outer axle bushing until tight. Push the wheel onto the axle. Insert the flat washer

Ø16 and attach the axle end cap by tapping with a wooden or rubber mallet.

▪ Then mount the left wheel. Slip the flat washer (16), the wheel (25) and another flat

washer (16) from the left side onto the right side of the wheel axle. The wheel is secured in

its position by means of a cotter pin. Push the cotter pin (13) through the wheel axle. Bend

the ends of the cotter pin (lower part) outwards to safely secure the wheel.

NOTE: The nuts and bolts do not have to be completely tightened yet.

NOTE: Insert the inner axle bushing into outer axle bushing and make sure

they are tight.

3.6 Figure 6

Mount the handle shaft (19) for the handles (18) between the two top ends of the wheel

assembly frames. Insert the two bolts M6x45 (6) through the wheel assembly frames and the

handle shaft, then fasten these bolts with the lock nuts M6.

Go back and tighten all nuts and bolts assembled so far. Do not

overtighten.

NOTE: In the following step, the handle can be adjusted higher or lower,

depending on the user’s preference.

Before installing the gear wheel assembly, the upper handles and the handle shaft, decide

which of the three positions will be most comfortable for the operator. If the middle or the

upper positions are chosen, use the handle spacer in the opening nearest to the handle grips.

KRTGR9005 EN

3.7 Figure 7

▪ Insert the bolts M6x45 through the upper left handle, and then through the handle spacer

and the upper handle on the right side, screw them tight with the lock nut M6.

▪ Tighten nuts securely.

3.8 Figure 8

▪ Push the adjustable handle of the adjustment and lever assembly (28) to the lowest

position.

▪ Slide the adjustment cable through the clamping bracket of the guide plate of the handle

shaft.

▪ Clamp the metal sleeve part of the adjusting cable between the bracket (the end of the

tube and the bracket being positioned at the same height), and fasten the bracket with 2

Philips screws.

▪ Insert one end of the adjusting cable from the right side to the left side into the smallest

opening at the end of the adjustment and the lever assembly (28).

▪ Then mount the adjustment and lever assembly (28) to the connection tube, move the

lever forwards / backwards, and check the swift movement of the lever and the correct

function of the shut-off valve at the bottom of the hopper (Fig. 11).

4 ADJUSTMENTS (FIG. 10)

To operate this spreader, push the handle to its lowest position (downwards). You can change

the position of the wing nut on the adjustment and lever assembly to adjust the space of the

opening between the hopper and the adjustable plate, as per your need when spreading.

Release the 2 nuts to adjust the length of the cable to make sure the opening on the bottom of

the hopper is fully open or closed when the handle in the highest or lowest position.

KRTGR9005 EN

5 DECLARATION OF CONFORMITY

VARO – Vic. Van Rompuy N.V. – Joseph Van Instraat 9 – 2500 Lier – BELGIUM, declares

that,

product: Spreader

trade mark: KREATOR

model: KRTGR9005

is in conformity with the essential requirements and other relevant provisions of the applicable

European Directives, based on the application of European harmonized standards. Any

unauthorized modification of the apparatus voids this declaration.

European Directives (including, if applicable, their amendments);

2006/42/EC

European harmonized standards (including, if applicable, their amendments);

EN ISO 12100: 2010

Keeper of the Technical Documentation: Philippe Vankerkhove, VARO – Vic. Van Rompuy

N.V.

The undersigned acts on behalf of the company CEO,

Hugo Cuypers

Regulatory Affairs – Compliance Manager

24/10/2017, Belgium

Kreator KRTGR9005 Owner's manual

Kreator KRTGR9005 Owner's manual

Kreator KRTGR9005 Owner's manual

Related papers

Other documents