Murray 425306x48A Instruction book

Brand: Murray

Model: 425306x48A

Category: Lawnmowers

Type: Instruction book

The owner must be certain that all

the product information is included with the unit.

This information includes

the INSTRUCTION BOOKS,

the REPLACEMENT PARTS and the WARRANTIES.

This information must be included to make sure state laws and other laws

are followed.

PRODUCT INFORMATION

This Instruction Book contains information for several models.

Read and keep this book for future reference.

This book contains important information on

SAFETY, ASSEMBLY, OPERATION, AND MAINTENANCE.

RECORD THE FOLLOWING INFORMATION ABOUT YOUR UNIT. THIS

INFORMATION IS NECESSARY WHEN ORDERING PARTS OR IN CASE

OF LOSS OR THEFT.

BUILT IN THE

F-030750L

Model

425306x48A

F-030750L

TABLE OF CONTENTS

WARRANTY 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

RESPONSIBILITY OF THE OWNER 3. . . . . . . . . . . . . . . . . .

SAFETY RULES 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

INTERNATIONAL PICTORIALS 9. . . . . . . . . . . . . . . . . . . . . .

ASSEMBLY 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PARTS BAG - CONTENTS 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

HOW TO INSTALL THE SEAT 11. . . . . . . . . . . . . . . . . . . . . . . . . . . .

HOW TO ASSEMBLE THE STEERING WHEEL 11. . . . . . . . . . . .

HOW TO ASSEMBLE THE GAUGE WHEELS 11. . . . . . . . . . . . . .

MAINTENANCE FREE BATTERY 12. . . . . . . . . . . . . . . . . . . . . . . . .

HOW TO INSTALL THE BATTERY CABLES 12. . . . . . . . . . . . . . .

IMPORTANT! BEFORE YOU START MOWING 13. . . . . . . . . . . .

HOW TO PREPARE THE ENGINE 13. . . . . . . . . . . . . . . . . . . . . . . .

CHECK THE LEVEL OF THE MOWER HOUSING 13. . . . . . . . . .

CHECK THE TIRES 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

OPERATION 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

LOCATION OF CONTROLS 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ATTACHMENTS 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

HOW TO USE THE THROTTLE CONTROL 15. . . . . . . . . . . . . . . .

HOW TO USE THE BLADE ROTATION CONTROL 15. . . . . . . . .

HOW TO USE THE SPEED CONTROL PEDAL 16. . . . . . . . . . . . .

HOW TO SET THE PARKING BRAKE 17. . . . . . . . . . . . . . . . . . . . .

HOW TO CHANGE THE CUTTING HEIGHT 17. . . . . . . . . . . . . . . .

HOW TO STOP THE UNIT 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

HOW TO TRANSPORT THE UNIT 17. . . . . . . . . . . . . . . . . . . . . . . .

HOW TO OPERATE WITH THE MOWER HOUSING 18. . . . . . . .

HOW TO OPERATE AUTOMATIC DRIVE UNITS ON HILLS 18. .

BEFORE STARTING THE ENGINE 19. . . . . . . . . . . . . . . . . . . . . . .

HOW TO START THE ENGINE 19. . . . . . . . . . . . . . . . . . . . . . . . . . .

OPERATING TIPS 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MOWING AND BAGGING TIPS 20. . . . . . . . . . . . . . . . . . . . . . . . . . .

MAINTENANCE 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MAINTENANCE CHART 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

HOW TO CHECK THE MUFFLER 21. . . . . . . . . . . . . . . . . . . . . . . . .

HOW TO REMOVE AND INSTALL THE BLADE 22. . . . . . . . . . . .

HOW TO SHARPEN THE BLADE 22. . . . . . . . . . . . . . . . . . . . . . . . .

HOW TO ADJUST THE BLADE ROTATION CONTROL 23. . . . .

HOW TO CHECK AND ADJUST THE DRIVE BRAKE 24. . . . . . .

HOW TO CHECK AND ADJUST THE CLUTCH 24. . . . . . . . . . . . .

MAINTENANCE FREE BATTERY 25. . . . . . . . . . . . . . . . . . . . . . . . .

HOW TO CHARGE THE BATTERY 25. . . . . . . . . . . . . . . . . . . . . . .

WHERE TO LUBRICATE 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

HOW TO CHECK THE FUEL FILTER 26. . . . . . . . . . . . . . . . . . . . . .

CHECK THE TIRES 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

HOW TO REMOVE THE MOWER HOUSING 27. . . . . . . . . . . . . . .

HOW TO INSTALL THE MOWER HOUSING 27. . . . . . . . . . . . . . .

HOW TO ADJUST THE GAUGE WHEELS 28. . . . . . . . . . . . . . . . .

HOW TO LEVEL THE MOWER HOUSING 29. . . . . . . . . . . . . . . . .

HOW TO REPLACE

THE MOTION DRIVE BELTS 30. . . . . . . . . . . . . . . . . . . . . . . . . .

HOW TO REPLACE THE MOWER DRIVE BELT 33. . . . . . . . . . . .

HOW TO INSTALL THE WHEELS 34. . . . . . . . . . . . . . . . . . . . . . . . .

HOW TO REPLACE THE FUSE 35. . . . . . . . . . . . . . . . . . . . . . . . . .

HOW TO REPLACE THE LIGHT BULB 35. . . . . . . . . . . . . . . . . . . .

HOW TO CLEAN THE MOWER HOUSING 35. . . . . . . . . . . . . . . . .

STORAGE (OVER 30 DAYS) 35. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TROUBLE SHOOTING CHART 36. . . . . . . . . . . . . . . . . . . . . .

HOW TO ORDER REPAIR PARTS 37. . . . . . . . . . . . . . . . . . .

PARTS LIST 38. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SLOPE GUIDE 54. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

INDEX 55. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

LAWN TRACTOR ACCESSORIES 56. . . . . . . . . . . . . . . . . . .

MURRAY, INC. Two Year Limited Warranty

Murray, Inc. warrants to the original purchaser that this unit shall be free from defects in material and workmanship under normal

use and service for a period of Two (2) Years from the date of purchase; however, this warranty does not cover engines,

accessories (such as snow blowers, snow blades, grass baggers and plows), transmissions, batteries and Normal Wear Parts

(except as noted below) or transaxles as the companies that manufacture these items furnish their own warranties and provide

service through their authorized field service facilities. For additional information, see the warranties covering these particular

parts. If you are uncertain whether your unit contains or is equipped with one or more of these parts, consult your dealer prior

to purchase. Subject to the terms and conditions noted in this Limited Warranty, we shall, at our option, repair or replace at no

cost to the original purchaser any part covered by this Limited Warranty during the applicable warranty period.

In the event the battery proves defective within ninety (90) days from the date of purchase, we will replace it without charge. If

the battery proves defective after (90) days but within one hundred twenty (120) days from the date of purchase, we will replace

it for a charge of one half (1/2) of the retail price of the battery in effect at the time of return.

Normal Wear Parts are defined as belts, blades, blade adapters, pneumatic tires, headlights and seat covers. These parts are

warranted to be free from defects in material and workmanship as delivered with the product. Any claim for repair or replacement

of Normal Wear Parts must be made within thirty (30) days of the date of purchase. No claims involving damage caused from

material use, abuse or misuse will be honored.

This Murray, Inc. Two (2) Year Limited Warranty is your exclusive remedy; however, this warranty is void or does not apply

to any unit that has been tampered with, altered, misused, abused or used for rental or other commercial and/or professional

(non-homeowner) uses. Your warranty does not cover minor mechanical adjustments which are not due to any defect in material

or workmanship. For assistance in making such adjustments, consult your Instruction Book.

To make a claim under this Murray, Inc. Two (2) Year Limited Warranty, return the unit (or if authorized in advance, the defective

part) along with your proof of purchase to an Authorized Service Center near you. To locate the nearest Authorized Service

Center, call the Central Parts Distributor for your area shown in the list provided with your unit or check the Yellow Page listings

in your local telephone directory. If you return the entire unit, we will repair the unit. If we authorize the return of the defective

part only, we will either replace or repair the part. In the case of a defect in a transmission or differential (as distinguished from

a transaxle), the entire transmission or differential must be returned since they do not include user serviceable parts.

This Murray, Inc. Two (2) Year Limited Warranty gives you specific legal rights, and you may also have other rights which vary

from state to state.

This Limited Warranty is given in lieu of all other expressed and implied warranties including the

implied warranty of merchantability and warranty of fitness for a particular purpose. If you need additional information

on this written warranty or assistance in obtaining service, write or call: MURRAY, INC., Outdoor Power Equipment, Customer

Service Department, P.O. Box 268, Brentwood, Tennessee 37027. (1-800-251-8007)

OWNER’S INFORMATION

F-030750L

This instruction book is for several different models. The instructions

are written for a person with some mechanical ability. Like most ser-

vice books, not all the steps are described. Steps on how to loosen or

tighten fasteners are steps anyone can follow with some mechanical

ability. Read and follow these instructions before you use the unit.

Know your product: If you understand the unit and how the unit oper-

ates, you will get the best performance. As you read this manual, com-

pare the illustrations to the unit. Learn the location and the function of

the controls. To help prevent an accident, follow the operating instruc-

tions and the safety rules. Keep this manual for future reference.

IMPORTANT: Many units are not assembled and are sold in car-

tons. It is the responsibility of the owner to make sure the assembly

instructions in this manual are exactly followed. Other units are pur-

chased in an assembled condition. On assembled units, it is the re-

sponsibility of the owner to make sure the unit is correctly

assembled. The owner must carefully check the unit according to

the instructions in this manual before it is first used.

Engine Exhaust, some of its constituents, and

certain vehicle components contain or emit

chemicals known to the State of California to

cause cancer and birth defects or other repro-

ductive harm.

Battery posts, terminals and related accesso-

ries contain lead and lead compounds, chemi-

cals known to the State of California to cause

cancer and birth defects or other reproductive

harm. WASH HANDS AFTER HANDLING.

RESPONSIBILITY OF THE OWNER

The responsibility of the owner is to follow the instructions below.

1. Carefully read and follow the rules for safe operation.

2. Follow all the assembly instructions.

3. Inspect the unit.

4. Make sure that the operator of the unit knows how to correctly

use all standard and accessory equipment.

5. Operate the unit only with guards, shields, and other safety

items in place and working correctly.

6. Correctly adjust the unit.

7. Service the unit only with authorized or approved replacement

parts.

8. Complete all maintenance on the unit.

Environmental Awareness

D Do not fill the engine’s fuel tank completely full.

D Drain fuel for off-season storage.

D Use only unleaded gasoline.

D Service the air cleaner regularly.

D Change oil regularly. Use 10W-30 oil in summer.

D Tune-up the engine regularly.

D Keep equipment in efficient operating condition.

D Dispose of used engine oil properly.

SAFETY RULES

Safe Operation Practices for Ride-on Mowers

WARNING: This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the

following safety instructions could result in serious injury or death.

I. General operation

1. Read, understand and follow all instructions in the Instruction Book, on the machine, the engine and with any attachments before

starting.

2. Only allow responsible adults, who are familiar with the instructions, to operate the machine.

3. Clear the area of objects such as rocks, toys, wire, etc., which could be picked up and thrown by the blade.

4. Be sure the area is clear of other people before mowing. Stop the machine if anyone enters the area.

5. Never carry passengers.

6. Turn off power to the blades or any attachments before backing up. Do not mow in reverse unless absolutely necessary. Always look

down and behind before and while backing.

7. Be aware of the mower discharge direction and do not point it at anyone. Do not operate the mower without either the entire grass bagger

or the mower guard in place.

8. Slow down before turning.

9. Never leave a machine unattended with the engine running. Always turn off the blade(s), set the parking brake, stop the engine and

remove the key before dismounting.

10. Turn off power to attachment(s) when transporting or not in use. Turn off the blade(s) when not mowing.

11. Stop the engine before removing the grass bagger or unclogging the chute.

12. Mow only in daylight or good artificial light.

13. Do not operate the machine while under the influence of alcohol or drugs or when very tired.

14. Watch for traffic when operating near or crossing roadways.

15. Use extra caution when loading or unloading the machine into a trailer or truck.

16. Always wear goggles, safety glasses, or an eye shield when you operate the unit to protect your eyes from foreign objects that can be

thrown from the unit. Always wear eye protection when you make an adjustment or repair to the machine.

17. Use care when pulling loads or using heavy equipment.

a. Use only approved drawbar hitch points.

b. Limit loads to those you can safely control.

OWNER’S INFORMATION

F-030750L

c. Do not turn sharply. Use care when backing.

d. Use counterweights or wheel weights when suggested in the Instruction Book.

18. Do not operate this machine if you are taking drugs or other medication which can cause drowsiness or affect your ability to operate

this machine.

19. Do not use this machine if you are mentally or physically unable to operate this machine safely.

20. Data indicates that operators, age 60 years and above, are involved in a large percentage of riding mower related injuries. These opera-

tors should evaluate their ability to operate a riding mower safely enough to protect themselves and others from serious injury.

II. Slope operation

Slopes and rough terrain are major factors related to loss-of-control and tip-over accidents, which can result in severe injury

or death. ALL slopes require extra caution. If you cannot back up the slope or if you feel uneasy on the slope, do not mow it. See

the “Slope Guide” in the back of this book to check for safe operation.

1. Mow up and down slopes, not across.

2. Remove obstacles such as rocks, limbs, etc...

3. Watch for holes, ruts or bumps. Uneven terrain could overturn the machine. Tall grass can hide obstacles.

4. Follow the manufacturer’s recommendations for wheel weights or counterweights to improve stability.

5. Use extra care with grass baggers or other attachments, they can change the stability of the machine.

6. Keep all movement on the slopes slow and gradual. Do not make sudden changes in speed or direction.

7. Avoid starting or stopping on a slope. If tires lose traction, turn off the blades and proceed slowly straight down the slope.

DO NOT

1. Do not turn on slopes unless absolutely necessary, then only turn slowly and gradually downhill, if possible.

2. Do not mow drop-offs, ditches or embankments. A wheel over the edge or an edge caving in could cause a sudden overturn and an

injury or death.

3. Do not mow on wet grass. Reduced traction could cause sliding.

4. Do not try to stabilize the machine by putting your foot on the ground.

5. Do not use a grass bagger or other rear mounted accessories on steep slopes (greater than 10 degrees).

III. Children

Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and

the mowing activity. NEVER assume that children will remain where you last saw them.

1. Keep children out of the mowing area and in the watchful care of another responsible adult.

2. Be alert and turn the engine off if children enter the area.

3. Before and when backing, look behind and down for small children.

4. Never carry children or any passengers, even with the blades off. They may fall off and be seriously injured or interfere with the safe

operation of the machine.

5. Never allow children to operate the machine. Instruct children in the potential dangers of the machine.

6. Use extra care when approaching blind corners, shrubs, trees or other objects that may obscure vision.

IV. Service

1. Use extra care when handling gasoline and other fuels. Fuels are flammable and the vapors are explosive.

a. Use only an approved container.

b. Never remove the gas cap or add fuel with the engine running. Allow the engine to cool for several minutes before refueling. Do

not smoke.

c. Never refuel the machine indoors.

d. Never store the machine with fuel in the tank or fuel container inside where there is an open flame, such as a water heater.

2. Never start or run the engine inside a closed area.

3. Keep all nuts and bolts, especially the blade attachment nuts tight. Frequently check the blade(s) for wear or damage such as cracks

and nicks. A blade that is bent or damaged must be immediately replaced with an original equipment blade from an authorized service

dealer. For safety, replace the blade every two years. Keep the equipment in good condition.

4. Never tamper with the safety devices. Check their proper operation regularly.

5. To reduce fire hazards, keep the machine free of grass, leaves or other debris build-up. Clean up oil or fuel spills. Allow the machine

to cool before storing.

6. Stop and inspect the equipment if you strike an object. Repair, if necessary, before restarting.

7. Never make adjustments or repairs with the engine running. The carburetor can be adjusted with the engine running. Do not change

the engine governor settings or over-speed the engine.

8. Grass bagger components are subject to wear, damage and deterioration, which could expose moving parts or allow objects to be

thrown. For storage, always make sure the grass bag is empty. Frequently check components and replace with manufacturer’s recom-

mended parts when necessary.

9. Mower blade(s) are sharp and can cut. Wrap the blade(s) or wear gloves and use extra caution when servicing them or the blade housing

area.

10. Check the brake operation frequently. Adjust and service as required.

11. Wait for all movement to stop before servicing any part of the unit.

Look for this symbol to indicate important safety

precautions. This symbol indicates: “Attention!

Become Alert! Your Safety Is At Risk.”

SAFE MOWING GUIDE

F-030750L

Each person that operates power

equipment must learn to use correct and

safe mowing procedures. To help you

learn, carefully read the following

pages. Most of the time the operator was

not correctly shown or did not read the

instructions on the unit or in the Instruction

Book before using the unit. Also, some

operators do not have enough experience.

The result is unsafe use, endangering the

operator, bystanders and the equipment.

Another result can be a poor appearance

of the area mowed.

Read this book. Read the instructions on

the unit. Operate the mower according to

the Safe Mowing Guide. Follow all safety

rules, cautions or warnings in this book

and on the unit. Make sure anyone that

uses the unit reads the instructions and is

told how to safely operate the mower.

The mower will give you good service and

durability, if operated in normal conditions.

If the mower is not correctly serviced or is

used where the terrain is rough or

unsuitable, product performance and

safety will be decreased.

Correct clothing is an important part of safe

mowing. Safety glasses will protect the

eyes from objects discharged by the

mower. Safety shoes with steel plates can

protect a foot from injury by the blade. For

protection from objects discharged from

the mower, wear clothing that will cover the

arms and legs.

Before you start cutting the grass, practice

using the mower in a large open and level

area. Learn the location of the controls on

the mower. Know the purpose of the

controls and how they work. In an

emergency, how fast you can stop the

blade is important. Learn how to control

the mower at all times.

Many engines are started by hand. When

you use a pull start or rope start, place

your feet apart and away from the blade(s).

Hold the rope handle tight. Never wrap the

rope around your arm or fingers for a

“better grip”. To start the engine, follow the

instructions on the mower, in this book and

in the engine operating instructions.

For electric start engines, sit in the seat to

start the engine. The battery can be

dangerous. Follow the instructions on the

battery, the acid container, and in this book

when working with the battery. Even small

batteries have enough voltage to cause an

injury. Always be careful.

The mower is designed to be operated by

one person. Never let another person ride

with you on the unit or on any accessories.

A passenger will make the unit harder to

control, block the visibility or distract the

operator and is dangerous to the operator,

the passenger and the equipment. Without

a passenger seat, the passenger can fall

from the mower or contact dangerous

parts. A mower is not a toy for showing off

or for giving rides.

Never cut a wet lawn. Wet grass can

cause an accident, affect mower

performance and can cause problems with

future lawn growth and appearance. Wet

grass is slippery and can cause the mower

to slip. Someone can get injured by

touching the blade(s). Wet grass tends to

clog the mower, causing poor discharge.

Cut wet grass will collect on the lawn,

retarding the growth of the grass. Also,

getting the mower wet will cause parts to

rust and decrease the life of the unit.

When you look over the lawn, remember

obstacles that cannot be removed, like

pipes, stumps or rocks. Keep away from

these obstacles that can cause damage to

the mower or injury to the operator or a

person near the mower. Clear the area of

rocks, toys, wire or other loose objects.

These items can damage the mower or

can be discharged by the mower blade.

The blade of a power mower rotates very

fast. It can discharge rocks and other

objects over a long distance which can be

dangerous. The force of the objects can

break windows, cause injuries or even put

an eye out. Most of the time the injury is to

a person, like a child. Keep every person

completely away from the area to be

mowed. Make sure the grass is not

discharged toward anyone. Planning your

mowing pattern has a double advantage. It

can decrease the possibility of an injury

and make the clean up after mowing

easier.

Check the terrain of the area to be mowed.

Mow in a pattern that will keep you away

from dangerous areas. Check the distance

you need to stop and the distance

available to turn. Slopes and rough terrain

must be mowed carefully and some areas

must not be mowed at all. With riding

mowers, mow up and down the hill.

Before you ride up or down a slope, try to

back straight up the slope. Do not ride up

or down a slope that is too steep to back

straight up. See the “Guide” in the back of

this Instruction Book to check any slopes.

Before you start cutting, make sure the

mower was completely assembled

according to the Instruction Book. If the

mower was completely assembled at the

store, you must still check the mower

according to the assembly instructions.

Make sure the mower is correctly

SAFE MOWING GUIDE

F-030750L

assembled and that all fasteners are tight.

Make sure the engine has the correct

amount of oil. Check these items often

during the life of the mower.

Your mower has a gasoline engine.

Gasoline is a dangerous fuel. Keep

gasoline only in an approved safety

gasoline container. Do not keep large

amounts of gasoline. When you add

gasoline to the fuel tank, do not smoke.

Store the gasoline container and the

mower in an area that has good ventilation.

Also, keep the gasoline away from any

flames like the pilot light of a furnace or

any other source of ignition. If the mower is

to be stored for more than a few weeks,

remove the gasoline from the fuel tank.

When inside an enclosure, do not add

gasoline to the fuel tank. Before you add

gasoline, move the mower outside and add

gasoline carefully. Before you start the

engine, remove any gasoline from the

outside of the fuel tank or from the mower.

Warm gasoline will expand. Leave some

space in the fuel tank for the gasoline to

expand. Also, the fuel cap has a vent hole

for fuel vapors. Always use the correct fuel

cap. Failure to follow safety rules about

gasoline will cause fires and explosions,

injury to you and damage to the equipment

and other property.

If you add gasoline to an engine that is

running or hot, the result can be an

explosion. Before you add gasoline, stop

the engine and let the engine cool for

several minutes. Remove dry grass and

other debris from the mower. Keep the

mower clean to improve the performance,

help the engine and transmission run

cooler, extend the life of moving parts, and

decrease the danger of a fire.

Fires and explosions are not the only

dangers when working around a mower.

The engine, transmission, and the muffler

will get hot in several minutes when the

engine is running. Do not touch these parts

of the mower. Stop the engine. Let the

engine and transmission cool before

servicing the mower. Remember, exhaust

fumes are dangerous. Never operate the

engine inside a building.

When you get a new mower, it can be a

new experience for the family. Tell each

person how a mower can be dangerous.

Remember, a mower is not a toy. A mower

is not to be used by children or anyone not

old enough, strong enough or that does not

have experience.

If the mower is not correctly assembled,

not operated correctly, or not regularly

serviced, the mower can be dangerous.

The most important rule to follow is always

use good judgement and common sense.

Mow safely and carefully.

Your mower will easily cut thick grass.

Fingers, feet and other parts can also be

cut by the blade. Injuries occur when the

operator does not think and reaches into

the chute opening. Always operate the

mower as if the blade is rotating. Do not

service or make an adjustment, except to

the carburetor, while the engine is running.

Use only accessories that are factory

approved for your mower. The wrong

accessory can decrease the safety of the

mower and can even damage the unit.

Read and follow the instructions included

with the accessory and the mower.

Use only original equipment or

replacement parts that are factory

approved for service. If you need service,

select an Authorized Service Center for

your mower. If you do the work on the unit,

follow the instructions in the Instruction

Book.

When you mow, remember that children

are attracted to the mower. Always use

caution when mowing around obstacles

like trees or shrubs or when moving

backward. Only mow in a forward direction

if possible. Your visibility is decreased

when you mow backward. Also, the blades

are made to cut while the unit is moving

forward. If you mow backward, the cutting

performance decreases.

Before you leave the mower, stop the

engine. Remove the key. Disengage and

lower any attachment. Set the parking

brake. Never mount or dismount from the

seat while the engine is running. Mount

and dismount from the seat on the side of

the unit that is marked ENTER-EXIT.

Make sure you are in good condition when

you mow. When you mow for several hours

your reflexes will decrease and your mind

will not be as alert. Take a short break or

an accident can occur. If the temperature is

hot, use caution to prevent dehydration. If

you are tired, angry or not completely alert,

do not operate the mower. If you use

alcohol, medication or drugs, do not use

the mower or any type of power

equipment.

Engine speed is a key to safe mowing and

to a good looking lawn. The maximum

speed of the engine was set at the factory.

Do not change the setting of the engine

governor.

Select the maximum engine and ground

speed that is right for the terrain and the

height of the grass. The blade cuts best

when the engine is operating at maximum

speed. The engine and transmission will

also run cooler at maximum engine speed.

Also, the grass bagger will function better

when the engine is operating at maximum

speed. On slopes, decrease the ground

speed and use care making sure the

mower feels safe to operate.

If the weather conditions are bad, do not

mow. If weather conditions become bad,

SAFE MOWING GUIDE

F-030750L

stop cutting and finish later. It is dangerous

to cut grass in the rain. Always find

protection in an electrical storm. If the

weather conditions are extra dry, protect

your eyes with safety glasses from the dust

and from the objects discharged by the

mower. Also, a dust or a pollen mask can

help.

Your mower is equipped with a number of

safety devices which are important to the

safety of the operator and bystanders and

must never be changed or removed from

the mower. If a safety device is lost,

damaged or no longer functions, repair or

replace the device before you operate the

mower.

It is best to mow during the day. If you

must mow at night, make sure there is

enough light for safe operation.

Your mower will require regular

maintenance and service. The

maintenance schedule depends on the

hours of use. Also, mowing conditions can

change the schedule. Check the

Instruction Book for more information.

Correct maintenance will help the mower

function safely.

Do not service the

mower (except for the

carburetor adjustment)

while the engine is

running. Before you

service the unit, even

with the engine stopped,

always disconnect the

wire from the spark plug

to prevent the engine

from starting.

If you hit a large object during operation,

stop the engine. Remove the wire from the

spark plug. Carefully inspect the mower for

damage. Before you start the engine

again, make the necessary repairs. If you

feel new or excessive vibration,

immediately stop the engine and check for

the problem. Vibration can be a warning of

a problem. Keep all nuts, bolts and screws

tight.

The blade is the most dangerous part of

the mower. Frequently check the blade and

the blade mounting fasteners. Keep the

fasteners tight. If the blade hits a solid

object, stop the engine. Remove the wire

from the spark plug. Check for a blade that

is bent, cracked or for other damages.

Before you start the engine, replace a

damaged blade(s). For safety, replace the

blade every two years.

A sharp blade decreases the workload on

the engine and more evenly cuts grass.

Frequently sharpen the blade for a better

looking cut. Use the left side of the mower

housing to trim near an object.

A grass bagger is a good accessory for

your mower. For best performance and

safety, make sure the grass bagger is

approved for use with your mower. Follow

the assembly and operation instructions

included with the grass bagger.

Some grass baggers require a special

blade for best performance. Before you

attach, check, or empty the grass bagger,

always stop the engine. Before each use of

the grass bagger, check for cracks, wear or

deterioration. Before you use the grass

bagger, replace a damaged part with a

replacement part approved by the factory.

For you to have a good green lawn, follow

the mowing procedures below. Do not cut

the grass too short. If you cut the grass too

short you can cause the grass to become

yellow or make the lawn look brown. Use a

lower height of cut in cool months when

the grass is thicker. Raise the height of cut

in hot dry periods. If you cut the grass with

a blade that is not sharp or at a slow

engine speed you can damage the grass.

Move the throttle control to the FAST

position when mowing and using the grass

bagger. Also, use a slower ground speed

when using the grass bagger.

If you change the direction or pattern of cut

slightly every time you mow will make the

grass grow stronger and thicker. Do not

add oil or gasoline to the mower while on

the lawn. Spilled oil or gasoline can kill the

grass. In high or thick grass, do not try to

cut all the grass the first time. Raise the

height of cut on the first cutting and lower

the height for the next cutting. Another way

is to cut only part of the width of the mower

and decrease your ground speed (not the

engine) to move more slowly so that the

mower can discharge the grass as it

moves forward.

Understand the controls and how they

work. Learn the ground speed(s) of your

mower. Check the stopping distance

required at different travel speeds. Check

the turning radius of the mower. The

controls on your riding mower are different

from an automobile. The throttle is

operated by hand and holds the engine

speed constant until it is changed. Also,

the brake and clutch systems are different.

Remember the procedures to follow in an

emergency. Remember, turning off the

engine ignition switch will stop the blade

and the drive mechanism. If the traction of

the wheels is lost or does not feel safe,

disengage all systems and stop the

engine. Dismount from the mower. Push

the unit to a safe place before you begin

mowing again.

Your unit has an electrical system that

includes an operator presence switch in

the seat. The operator presence switch

detects if the operator is sitting on the seat.

The engine will stop if the operator leaves

the seat when the blade engagement

control is engaged. This operator presence

switch is a safety device only. It must not

regularly be used to stop the engine or the

blade. There are other control systems on

the mower for this purpose. Always keep

the operator presence switch and other

safety devices and controls in place and

operating for your protection.

Remember, your mower is a tool that can

be dangerous if it is not correctly used.

Follow the instructions in this Instruction

Book. Safe and careful use of the mower

will give you many safe hours of problem

free use.

STEPS TO FOLLOW

F-030750L

BEFORE MOWING

F Be sure to dress correctly. Wear hard shoes, not sandals or tennis shoes.

F Examine the blade. A blade that is bent, cracked, or damaged must be replaced with a factory replacement blade.

F Fill the fuel tank outside. Clean off spilled fuel.

F Read and follow the Owner’s Manual, the instructions with the engine, and the instructions with any attachments. Owner’s Manual

instructions are for your safety and the safety of others.

F Exhaust fumes are dangerous. Start the engine outside.

F Make sure all safety devices are in place and working correctly.

F Operation of the mower is only for a person that has experience.

F Wet grass can be dangerous. Let the grass dry.

F Instruct children and others to keep away from the work area.

F Never cut the grass without good light.

F Pick up loose objects. Remove them from the mowing area.

WHILE MOWING

F Watch for fixed objects and avoid them. They can damage the mower or cause injury.

F A hot engine, muffler, and transmission will cause a burn. Do not touch.

F Inclines and slopes must be carefully mowed. See the “Guide” in the back of this book to check a slope.

F Lack of daylight or good artificial light is cause to stop mowing.

F Examine the mower, the blade, and other parts for damage after hitting a foreign object or if the unit vibrates excessively.

F Do not make adjustments or repairs without stopping the engine. Disconnect the spark plug wire.

F On or near roads, watch out for traffic. Direct discharge away from roads.

F When mowing, avoid areas where traction is unsure. Look back before changing direction of travel.

F In heavy grass, raise the cutting height. Cut slower. Stop the engine to remove clogged grass from the mower.

F Never remove any safety related parts.

F Do not pour gasoline into a engine that is hot or running.

AFTER MOWING

F Always let the mower cool before storing in an enclosed area.

F Foreign material on the mower is dangerous. Clean off grass, leaves, grease and oil before storing.

F Tighten all loose nuts, bolts and screws before you use the unit.

F Empty and clean any grass catcher or other accessory.

F Remove the key or disconnect the spark plug wire to prevent unauthorized use.

F Make sure the mower is not kept near a source of ignition. Gas fumes can cause an explosion.

F Only original parts or factory approved substitutes can be used to service the mower.

F When storing the mower for an extended period, remove the fuel from the fuel tank.

F Instruct children to leave the mower alone. It is not a toy.

F Never keep gasoline near a source of ignition. Always use an approved container. Keep gasoline away from children.

F Lubricate according to the Instruction Book. See “Lubrication”.

IMPORTANT--Read the Instruction Book. Keep this book for future use and reference.

WARNING: Look for this symbol to point out important

safety precautions. It means: “Attention! Become Alert!

Your Safety Is Involved.”

INTERNATIONAL PICTORIALS

F-030750L

INTERNATIONAL PICTORIALS

IMPORTANT: Some of the following pic-

torials are located on your unit or on

literature supplied with the product. Be-

fore you operate the unit, learn and un-

derstand the purpose for each pictorial.

Safety Warning Pictorials

1 Warning

2 Shield Eyes. Explosive Gases Can

Cause Blindness Or Injury.

3 No Sparks, Flames or Smoking.

4 Sulphuric Acid Can Cause Blindness

Or Severe Burns

5 Flush Eyes Immediately With Water.

Get Medical Help Fast.

6 IMPORTANT: Read Owner’s Manual

Before Operating This Machine.

7 WARNING: Thrown Objects. Keep

Bystanders Away. Read User

Instructions Before Operating This

Machine.

8 WARNING: Do Not Use This Machine

On Slopes Greater Than 15 Degrees.

9 DANGER: Keep People, Especially

Children, Away From Unit.

10 DANGER: No Step.

11 DANGER: Keep Feet And Hands

Away From Rotating Blade.

12 DANGER: Keep Hands Away From

Rotating Blade.

13 DANGER: Disconnect Spark Plug

Wire Before Servicing Unit.

14 WARNING: Hot Surface.

15 WARNING: Use Caution When

Connecting Or Disconnecting

Accessories.

16 WARNING: Crushed Fingers.

MAX 90N

MAX 150N

12 3 546

Control And Operating Pictorials

1 Engine Start

2 Lights

3 Engine Stop

4 Engine Stop

5 Engine Run

6 Brake

7 Parking Brake

8 Clutch

9 Slow

10 Fast

11 Choke

12 Oil

13 Blade Rotation Control

14 Raise

15 Fuel

10 11 12

ASSEMBLY

F-030750L

ASSEMBLY

This instruction book is for several models. Some parts or accesso-

ries are not included on all models. Read and follow the assembly

and adjustment instructions for your mower. All fasteners are in the

parts bag. Do not discard any parts or material until the unit is

assembled.

WARNING: Before doing any assembly or mainte-

nance to the mower, remove the wire from the spark

plug.

NOTE: In this instruction book, left and right describe the loca-

tion of a part with the operator on the seat.

PARTS BAG - CONTENTS

The fasteners and other loose parts are shown below. The fasteners are shown full size. The quantity is shown in brackets ( ).

2x82

(2) Carriage Bolt

14x79

(2) Wing Nut

17x47

(2) Washer

20729

(1) Keys & Ring

1001054

(2) Knob

17x91

(4) Washer

31x11

(2) Hair Pin

ASSEMBLY

F-030750L

HOW TO INSTALL THE SEAT

Use the fasteners shown below to install the seat. The fasteners are

shown at full size.

(A)

1001054

(B)

17x47

1. Carefully remove the plastic bag from the seat.

2. Align the holes in the seat hinge to the holes in the seat

(Figure 1). Fasten the seat to the seat hinge with the fasteners

as shown.

3. Check the operating position of the seat. If the seat needs to

be adjusted, loosen the two wing bolts. Slide the seat forward

or backward along the seat adjusting holes as shown. Tighten

the wing bolts (A).

Figure 1

Seat

Adjusting Hole

Seat Hinge

HOW TO ASSEMBLE THE STEERING WHEEL

Fasteners are not required to assemble the steering wheel. Attach

the steering wheel as follows:

1. Make sure the front wheels point forward.

2. Look at the hub of the steering wheel. Make sure the locking

clip is in place inside the hub.

3. Slide the cover over the steering post (Figure 2).

4. Slide the steering wheel onto the steering post. Push on the

steering wheel. The steering wheel will lock onto the steering

post. Pull on the steering wheel. Make sure the steering wheel

is locked in place.

5. Some models have an decal in the parts bag. Attach the decal

to the center of the steering wheel as shown.

Steering Wheel

Steering Post

Cover

Decal (Optional)

Figure 2

Hub

HOW TO ASSEMBLE THE GAUGE WHEELS

Use the fasteners shown below to install the gauge wheels. The

fasteners are shown at full size.

(A)

31x11

(B)

17x91

1. Attach the gauge wheels to the axle bolts with the fasteners.

NOTE: The axle bolt is mounted in the LOW position. To change

the position to a higher cutting position, see “How To Adjust

The Gauge Wheels” in the Maintenance section.

Gauge Wheel

Figure 3

Axle Bolt

ASSEMBLY

F-030750L

MAINTENANCE FREE BATTERY

IMPORTANT: Before you attach the battery cables to the

battery, check the battery date. The battery date tells if the

battery must be charged.

1. Check the top of the battery for the location of the battery date

(Figure 4).

2. If the battery is put into service before the battery date, the

battery cables can be attached without charging the battery.

See “How To Install The Battery Cables”.

3. If the battery is put into service after the battery date, the

battery must be charged. See “How To Charge The

Maintenance Free Battery”.

HOW TO CHARGE

THE MAINTENANCE FREE BATTERY

WARNING: When you charge the battery, do not

smoke. Keep the battery away from any sparks. The

fumes from the battery acid can cause an explosion.

1. Remove the battery and battery tray.

2. Remove the protective caps from the battery terminals.

3. Use a 12 volt battery charger to charge the battery. Charge at

a rate of 6 amperes for one hour. If you do not have a battery

charger, have an authorized service center charge the battery.

4. Install the battery and battery tray. Make sure the positive (+)

terminal is on the left side.

HOW TO INSTALL THE BATTERY CABLES

WARNING: To prevent sparks, fasten the red cable to

the positive (+) terminal before you connect the black

cable.

Use the fasteners shown below to install the battery cables. The

fasteners are shown at full size.

(B)

14x79

(A)

2x82

1. Remove the protective caps from the battery terminals.

2. Fasten the red cable to the positive (+) terminal with the

fasteners as shown (Figure 4).

3. Fasten the black cable to the negative (-) terminal with the

fasteners as shown.

Positive (+)

Terminal

Black Cable

Red Cable

Battery Tray

Battery

Figure 4

ASSEMBLY

F-030750L

IMPORTANT! BEFORE YOU START MOWING

- Check the engine oil.

- Fill the fuel tank with gasoline.

- Check the level of the mower housing.

- Check the air pressure of the tires.

- Make sure the battery cables are attached.

WARNING: Before doing any assembly or mainte-

nance to the mower, remove the wire from the spark

plug.

NOTE: In this instruction book, left and right describe the loca-

tion of a part with the operator on the seat.

HOW TO PREPARE THE ENGINE

NOTE: The engine was shipped from the factory filled with oil.

Check the level of the oil. Add oil as needed.

See the engine manufacturer’s instructions for the type of gasoline

and oil to use. Before you use the unit, read the information on

safety, operation, maintenance, and storage.

WARNING: Follow the engine manufacturer’s

instructions for the type of gasoline and oil to use.

Always use a safety gasoline container. Do not

smoke when adding gasoline to the engine. When

inside an enclosure, do not fill with gasoline. Before

you add gasoline, stop the engine. Let the engine

cool for several minutes.

IMPORTANT: This unit is equipped with an internal combustion

engine and must not be used on or near any unimproved

forest-covered, brush-covered or grass-covered land unless

the engine’s exhaust system is equipped with a spark arrester

meeting applicable local or state laws (if any). If a spark

arrester is used, it must be maintained in effective working

order by the operator.

In the State of California the above is required by law (Section

4442 of the California Public Resources Code). Other states

may have similar laws. Federal laws apply on federal lands.

See an Authorized Service Center for a spark arrester for the

muffler.

In some areas, local law requires the use of a resistor spark

plug to control the ignition signals. See an Authorized Service

Center for a resistor spark plug for the engine.

CHECK THE LEVEL OF THE MOWER HOUSING

Make sure the level of cut is still correct. After you mow a short

distance, look at the area that was cut. If the mower housing does

not cut level, see the instructions on “How To Level The Mower

Housing” in the Maintenance section of this instruction book.

CHECK THE TIRES

Check the air pressure in the tires. Tires with too much air pressure

will cause the unit to ride rough. Also, the wrong air pressure will

keep the mower housing from cutting level. The correct air pressure

(PSI) is 14 PSI (1 BAR). The tires were over inflated for shipment.

OPERATION

F-030750L

Figure 5

Throttle Control

Lever

Blade Rotation

Control

Lift

Lever

Speed

Control

Pedal

Shift

Lever

Clutch/Brake

Pedal

LOCATION OF CONTROLS

BLADE ROTATION CONTROL: Use the blade rotation

control to start and stop the rotation of the blades.

CLUTCH / BRAKE PEDAL: The pedal has two functions.

The first function is a clutch. The second function is a brake.

HEADLIGHT SWITCH: The headlight switch is the first part

of the ignition switch. To use the lights with the engine running, turn

the key to the position for the lights.

IGNITION SWITCH: Use the ignition switch to start and stop

the engine.

SHIFT LEVER: Use the shift lever to change the speed and the

direction of the unit.

LIFT LEVER: Use the lift lever to change the height of cut.

PARKING BRAKE LEVER: Use the parking brake lever

to engage the brake when you leave the unit.

SPEED CONTROL PEDAL: Use the speed control pedal

to change the speed of the unit.

THROTTLE CONTROL LEVER: Use the throttle control

lever to increase or decrease the speed of the engine.

OPERATION

F-030750L

ATTACHMENTS

This unit can use many different attachments. See the attachment

page in this book. This unit can pull attachments like a lawn

sweeper, a lawn aerator, a hopper spreader or a small trailer. This

unit can not use attachments that engage the ground like a plow, a

disk harrow, or a cultivator.

For all pull-behind attachments or trailers, the maximum gross

weight is 250 pounds. Gross weight is the weight of the attachment

or trailer and any load that might be on or in it.

Do not operate on a slope that is greater than 10 degrees when

using a pull-behind attachment or trailer. We have included a slope

guide in this book to help you determine the slope on which you will

be operating your unit. Never allow someone to stand or ride on or

in an attachment or trailer.

HOW TO USE THE THROTTLE CONTROL

Use the throttle control to increase or decrease the speed of the

engine.

CAUTION: Always operate the engine with the throttle control

in the FAST position. If the engine runs for several minutes at

slower than the FAST position, the engine and transmission

will overheat and can be damaged.

1. The FAST position is marked with a detent. For normal opera-

tion and when using a grass bagger, move the throttle control

to the FAST position. For maximum charging of the battery and

for a cooler running engine and transmission, operate the en-

gine in the FAST position.

2. For transport and to tow pull behind attachments, control the

ground speed with the speed control pedal.

3. The engine governor is set at the factory for maximum perform-

ance. Do not adjust the governor to increase the speed of the

engine.

HOW TO USE THE BLADE ROTATION CONTROL

The blade rotation control is next to the steering wheel (Figure 6).

Use the blade rotation control to engage the blade(s) or to operate

a snow thrower attachment.

1. Before you start the engine, make sure the blade rotation con-

trol is in the DISENGAGE position.

2. Move the blade rotation control to the ENGAGE position to

rotate the blade(s).

Note: If the engine stops when you engage the blade(s),

the seat switch is not activated. Make sure you sit in the

middle of the seat. Also, make sure the wire is connected

to the seat switch.

3. Move the blade rotation control to the DISENGAGE position

to stop the blade(s). Before you leave the operator’s position,

make sure the blade(s) has stopped rotating.

4. Before you ride the unit across a sidewalk or a road, move the

blade rotation control to the DISENGAGE position.

WARNING: Always keep your hands and feet away

from the blade, deflector opening, and the mower

housing when the engine runs.

Blade Rotation Control

Engage Position

Disengage

Position

Figure 6

OPERATION

F-030750L

HOW TO USE THE SPEED CONTROL PEDAL

The drive system uses a variator pulley connected to a two speed

transaxle. The Variator Drive is very easy to operate. This type of

drive system has a two speed shift lever and a clutch/brake pedal

located beside the speed control pedal (see Figure 7).

The direction of travel is controlled by the shift lever. Use the shift

lever to select either reverse or one of the two forward gears. When

operating, the speed is controlled by a single speed control pedal

operated with your right foot.

HOW TO DRIVE FORWARD

1. Completely push the clutch/brake pedal forward to stop the

unit. Keep your foot on the pedal.

2. Move the shift lever to one of the TWO FORWARD positions.

Select Low position (TRIM) when going up or down steep hills

and when operating attachments that require a very slow for-

ward speed, such as snow throwers. Select High position

(MOW) when mowing or when transporting the unit.

3. Slowly release your right foot from the clutch/brake pedal. Do

not keep your foot on the clutch/brake pedal.

4. Move the throttle control to the FAST position.

5. Slowly push the speed control pedal forward to the desired

speed (see Figure 7).

6. To increase forward speed, slowly move the speed control

pedal forward. To reduce forward speed, slowly release the

speed control pedal until the unit slows to the desired speed.

HOW TO CHANGE DIRECTIONS

CAUTION: Before you move the shift lever, completely push

the clutch/brake pedal forward to the stop the unit. If the unit

is not stopped, the gearbox can be damaged.

1. Completely push the clutch/brake pedal forward to stop the

unit. Keep your foot on the pedal.

2. Move the throttle control lever to the SLOW position.

3. To go forward, move the shift lever to one of the TWO FOR-

WARD positions. To go backward, move the shift lever to the

REVERSE position.

4. Slowly release your right foot from the clutch/brake pedal. Do

not keep your foot on the clutch/brake pedal.

5. Move the throttle control to the FAST position.

HOW TO DRIVE IN REVERSE

1. Look to the rear.

2. Completely push the clutch/brake pedal forward to stop the

unit. Keep your foot on the pedal.

3. Move the shift lever to the REVERSE position.

4. Slowly release the clutch/brake pedal.

5. Slowly push the speed control pedal forward to the desired

speed.

6. To increase reverse speed, slowly move the speed control

pedal forward. To reduce reverse speed, slowly release the

speed control pedal until the unit slows to the desired speed.

Speed Control

Pedal

Figure 7

Clutch/Brake

Pedal

SPEED CONTROL PEDAL POSITIONS

The forward speed is controlled by the position of the shift lever and

the speed control pedal. The following chart provides functions

along with the positions of the shift lever and the speed control

pedal. Always operate the engine with the throttle control in the

FAST position.

FUNCTION

SHIFT LEVER

POSITION

PEDAL

POSITION

THROTTLE

Trimming

Snow Thrower

Steep Hills

Low (TRIM) 1/3

Bagging Grass High (MOW) 1/3 to 1/2

FAST

CHOKE

Normal Mowing High (MOW) 1/2 to 2/3

FAST

Easy Mowing

Snow Blade

High (MOW) 1/2 to 3/4

SLOW

THROTTLE

Transport High (MOW) FULL

Pull Behind

Attachments

High (MOW) 1/3 to 1/2

OPERATION

F-030750L

HOW TO SET THE PARKING BRAKE

1. Completely push the clutch/brake pedal forward.

2. Lift the parking brake lever (Figure 8).

3. Remove your foot from the clutch/brake pedal and then release

the parking brake lever. Make sure the parking brake will hold

the unit.

4. To release the parking brake, completely push the clutch/brake

pedal forward. The parking brake will automatically release.

NOTE: The parking brake must be disengaged before the

speed control pedal is able to engage the transmission.

WARNING: Before you leave the operator’s position,

move the shift lever to the neutral (N) position. Set the

parking brake. Move the blade rotation control to the

DISENGAGE position. Stop the engine and remove

the ignition key.

Figure 8

Parking

Brake

HOW TO CHANGE THE CUTTING HEIGHT

To change the cutting height, raise or lower the lift lever as follows.

1. Move the lift lever forward to lower the mower housing and

back to raise the mower housing (Figure 9).

2. When you ride on a sidewalk or road, move the lift lever to the

highest position and move the blade rotation control to the

DISENGAGE position.

Lift Lever

Figure 9

HOW TO STOP THE UNIT

1. Slowly remove your foot from the speed control pedal and de-

press the clutch/brake pedal.

2. Move the blade rotation control to the DISENGAGE position.

3. Set the parking brake.

WARNING: Make sure the parking brake will hold the

unit.

4. Move the throttle control to the SLOW position.

5. To stop the engine, turn the ignition key to the OFF position.

Remove the key.

HOW TO TRANSPORT THE UNIT

To transport the unit, follow the steps below.

1. Move the blade rotation control to the DISENGAGE position

2. Raise the lift lever to the highest position.

3. Depress the clutch/brake pedal and move the shift lever to the

High position (MOW).

4. Move the throttle control to the FAST position.

5. Release the clutch/brake pedal and slowly push the speed con-

trol pedal forward to the desired speed.

OPERATION

F-030750L

HOW TO OPERATE WITH THE MOWER HOUSING

WARNING: The deflector is a safety device. Do not re-

move the deflector. The deflector forces the dis-

charged material toward the ground. Always keep the

deflector in the down position. If the deflector is dam-

aged, replace the deflector with an original equipment

part from an authorized service center.

1. Start the engine.

2. Release the parking brake.

3. Move the lift lever to a height of cut position. In high or thick

grass, cut the grass in the highest position first and then lower

the mower housing to a lower position.

CAUTION: Do not operate with the mower housing in the

LEVEL ADJUSTMENT position. If you operate in the

LEVEL ADJUSTMENT position, the mower housing and

blades can be damaged.

4. Move the throttle control to the SLOW position.

5. Move the blade rotation control to the ENGAGE position.

6. Move the throttle control to the FAST position.

7. Slowly push the speed control pedal to the desired speed.

NOTE: When you mow in heavy grass or mow with a grass

bagger, use a slow forward speed.

8. Make sure the level of cut set at the factory is still correct. After

you mow a short distance, look at the area that was cut. If the

mower housing does not cut level, see the instructions on “How

To Level The Mower Housing” in the Maintenance section.

WARNING: For better control of the unit, always

select a safe speed.

HOW TO OPERATE AUTOMATIC DRIVE UNITS ON HILLS

WARNING: Do not ride up or down slopes that are too

steep to back straight up. Never ride the unit across

a slope. See the “Slope Guide” in the back of this

book for information on how to check slopes.

HOW TO OPERATE ON A HILL

1. Do not stop or change speed settings on a hill. If you must stop,

quickly push the clutch brake/pedal forward and set the parking

brake.

2. To help prevent an accident, slowly move the speed control

pedal. Avoid sudden turns or changes in speed.

3. To reduce forward speed when going down a hill, slowly release

the speed control pedal and, if necessary, depress the clutch/

brake pedal.

HOW TO STOP ON A HILL

1. Avoid stopping on a hill. If you must quickly stop in an emergen-

cy, remove your right foot from the speed control pedal and

quickly depress the brake/brake pedal.

2. Set the parking brake.

3. Before you dismount from the seat, move the throttle control to

SLOW position, move the blade rotation control to the DISEN-

GAGED position, turn off the engine and set the parking brake.

HOW TO START OPERATION ON A HILL

1. Start the engine

2. Move the blade rotation control to the ENGAGED position.

3. Move the throttle control to the FAST position.

4. Depress the clutch/brake pedal to release the parking brake.

Push the speed control pedal to the desired speed.

NOTE: The parking brake must be disengaged before the

speed control pedal is able to engage the transmission.

OPERATION

F-030750L

BEFORE STARTING THE ENGINE

CHECK THE OIL

NOTE: The engine was shipped from the factory filled with oil.

Check the level of the oil. Add oil as needed. See the engine

manufacturer’s instructions for the type of gasoline and oil to

use.

1. Make sure the unit is level.

NOTE: Do not check the level of the oil while the engine

runs.

2. Check the oil. Follow the procedure in the engine manufactur-

er’s instructions.

3. If necessary, add oil until the oil reaches the FULL mark on the

dipstick. The quantity of oil needed from ADD to FULL is shown

on the dipstick. Do not add too much oil.

ADD GASOLINE

WARNING: Always use a safety gasoline container.

Do not smoke when adding gasoline to the fuel tank.

Do not add gasoline when you are inside an enclo-

sure. Before you add gasoline, stop the engine and

let the engine cool for several minutes.

Fill the fuel tank with regular

unleaded gasoline. Do not use

premium unleaded gasoline.

Make sure the gasoline is fresh

and clean. Leaded gasoline will

increase deposits and shorten

the life of the valves.

CAUTION: A mixture of alcohol (ethanol or methanol) and

gasoline (called gasohol), will attract moisture and cause acid

deposits during storage. While the unit is in storage, the acids

in the fuel can damage the fuel system.

To prevent engine problems with the fuel system, empty the fuel

system before storage of 30 days or longer as follows.

1. Drain the fuel tank.

2. Start the engine. Let the engine run until the fuel lines and the

carburetor are empty.

3. After storage, make sure you use fresh fuel. See the storage

instructions for additional information.

4. Never use engine cleaner or carburetor cleaner in the fuel tank

or permanent damage can occur.

CARBURETOR

The factory settings for the carburetor are for most conditions. If the

engine is operated under the following conditions, you can adjust

the carburetor mixture. To adjust the carburetor, see the engine

manufacturer’s instructions.

1. The engine has a loss of power or does not run smooth.

2. A change from summer to winter operation.

3. A 40 degree change in the operation temperature. The carbure-

tor was adjusted at 80 degrees at the factory.

4. The engine is operated above 4,000 feet.

HOW TO START THE ENGINE

WARNING: The electrical system has an operator

presence system that includes a sensor switch for the

seat. These components tell the electrical system if

the operator is sitting on the seat. This system will

stop the engine when the operator leaves the seat if

the blade rotation control is engaged or if the trans-

mission is engaged. For your protection, always

make sure this system operates correctly.

1. Push the pedal completely forward. Keep your foot on the ped-

al.

2. Make sure the blade rotation control is in the DISENGAGE

position.

3. Move the throttle control completely forward to the CHOKE or

FAST position. Some models have a separate choke knob. Pull

the choke knob to the full CHOKE position.

4. Turn the ignition key to the START position. Release the key

when the engine starts.

NOTE: If the engine does not start after four or five tries,

see the TROUBLE SHOOTING CHART.

5. Slowly move the throttle control to the SLOW position.

6. Let a cold engine run for several minutes. Begin work when the

engine is warm. To start a hot engine, move the throttle control

to a position between FAST and SLOW.

Fuel Tank

Full

OPERATION

F-030750L

OPERATING TIPS

1. Check the blade rotation control for correct adjustment. For the

blade(s) to disengage correctly, the adjustment must be cor-

rect.

2. Before you use the unit, check the oil in the engine and add oil

if necessary.

3. If the engine will not start, first make sure the wire is attached

to the spark plug.

4. Make sure all the belts are inside all the belt guides. See the in-

structions on how to remove and install the motion drive and

mower drive belts.

5. Before you make an inspection, adjustment (except for the car-

buretor) or repair, make sure the wire from the spark plug is dis-

connected.

6. For longer life of the battery on electric start models, charge the

battery every three months.

MOWING AND BAGGING TIPS

1. For a lawn to look better, check the cutting level of the mower

housing. See “How To Level The Mower Housing” in the Main-

tenance section.

2. For the mower housing to cut level, make sure the tires have

the correct amount of air pressure.

3. Every time you use the unit, check the blade. If the blade is bent

or damaged, immediately replace the blade. Also, make sure

the nut for the blade is tight.

4. Keep the blade(s) sharpened. Worn blades will cause the ends

of the grass to turn brown.

5. Do not cut or bag grass that is wet. Wet grass will not discharge

correctly. Let the grass dry before cutting.

6. Use the left side of the mower housing to trim near an object.

7. Discharge the cut grass onto the mowed area. The result is a

more even discharge of cut grass.

8. When you mow large areas, start by turning to the right so that

the cut grass will discharge away from shrubs, fences, drive-

ways, etc. After one or two rounds, mow in the opposite direc-

tion making left turns until finished (Figure 10).

9. If the grass is very high, cut two times to decrease the load on

the engine. First cut with the mower housing in the highest posi-

tion and then lower the mower housing for the second cut.

10. For better engine performance and an even discharge of the

cut grass, always operate the engine with the throttle in FAST

position.

11. After each use, clean the bottom and top of the mower housing

for better performance. Also, a clean mower housing will help

prevent a fire.

Figure 10

Page is loading ...

Murray 425306x48A Instruction book

Brand: Murray

Model: 425306x48A

Category: Lawnmowers

Type: Instruction book

Download PDF

report

Murray 425306x48A Instruction book

Murray 425306x48A Instruction book

Other documents