Hitachi CP-WX3015WN User manual

1

Projector

User's Manual (detailed)

Operating Guide

Thank you for purchasing this projector.

►Before using this product, please read all manuals for this

product. Be sure to read Safety Guide ﬁrst. After reading them, store them in a

safe place for future reference.

WARNING

• The information in this manual is subject to change without notice.

• The illustrations in this manual are for illustrative purposes. They may differ

slightly from your projector.

• The manufacturer assumes no responsibility for any errors that may appear in

this manual.

• The reproduction, transfer or copy of all or any part of this document is not

permitted without express written consent.

NOTE

Trademark acknowledgment

Various symbols are used in this manual. The meanings of these symbols are

described below.

About this manual

WARNING

CAUTION

This symbol indicates information that, if ignored, could possibly

result in personal injury or even death due to incorrect handling.

This symbol indicates information that, if ignored, could possibly

result in personal injury or physical damage due to incorrect

handling.

Please refer to the pages written following this symbol.



• Mac

®

is a registered trademark of Apple Inc.

• Windows

®

, DirectDraw

®

and Direct3D

®

are registered trademarks of Microsoft Corporation

in the U.S. and/or other countries.

• VESA and DDC are trademarks of the Video Electronics Standard Association.

•

HDMI, the HDMI logo, and High-Deﬁnition Multimedia Interface are trademarks or registered

trademarks of HDMI Licensing LLC in the United States and other countries.

• Blu-ray Disc

TM

and Blu-ray

TM

are trademarks of Blu-ray Disc

Association.

All other trademarks are the properties of their respective owners.

NOTICE This entry notices of fear of causing trouble.

CP-X2015WN/CP-X2515WN/CP-X3015WN/

CP-X4015WN/CP-WX2515WN/CP-WX3015WN

1

About The Symbols

Various symbols are used in this manual, the user’s manual and on the product

itself to ensure correct usage, to prevent danger to the user and others, and to

prevent property damage. The meanings of these symbols are described below.

It is important that you read these descriptions thoroughly and fully understand

the contents.

Projector

User's Manual - Safety Guide

Typical Symbols

This symbol indicates an additional warning (including cautions). An

illustration is provided to clarify the contents.

This symbol indicates a prohibited action. The contents will be clearly

indicated in an illustration or nearby (the symbol to the left indicates that

disassembly is prohibited).

This symbol indicates a compulsory action. The contents will be clearly

indicated in an illustration or nearby (the symbol to the left indicates that

the power plug should be disconnected from the power outlet).

Thank you for purchasing this projector.

NOTE

• The information in this manual is subject to change without notice.

• The manufacturer assumes no responsibility for any errors that may appear in

this manual.

• The reproduction, transmission or use of this document or contents is not

permitted without express written authority.

WARNING •

Before using, read these user's manuals of this projector to ensure

correct usage through understanding. After reading, store them in a safe place for

future reference. Incorrect handling of this product could possibly result in personal injury

or physical damage. The manufacturer assumes no responsibility for any damage caused

by mishandling that is beyond normal usage defined in these manuals of this projector.

WARNING

This symbol indicates information that, if ignored, could

possibly result in personal injury or even death due to

incorrect handling.

CAUTION

This symbol indicates information that, if ignored, could

result possibly in personal injury or physical damage

due to incorrect handling.

Read this Safety Guide first.

2

Safety Precautions

WARNING

Never use the projector if a problem should occur.

Abnormal operations such as smoke, strange odor, no image, no sound,

excessive sound, damaged casing or elements or cables, penetration of

liquids or foreign matter, etc. can cause a fire or electrical shock.

In such case, immediately turn off the power switch and then disconnect the

power plug from the power outlet. After making sure that the smoke or odor

has stopped, contact your dealer. Never attempt to make repairs yourself

because this could be dangerous.

• The power outlet should be close to the projector and easily accessible.

Use special caution for children and pets.

Incorrect handling could result in fire, electrical shock, injury, burn or vision

problem.

Use special caution in households where children and pets are present.

Do not insert liquids or foreign object.

Penetration of liquids or foreign objects could result in fire or electrical shock.

Use special caution in households where children are present.

If liquids or foreign object should enter the projector, immediately turn off the

power switch, disconnect the power plug from the power outlet and contact

your dealer.

• Do not place the projector near water (ex. a bathroom, a beach, etc.).

• Do not expose the projector to rain or moisture. Do not place the projector

outdoors.

• Do not place flower vases, pots, cups, cosmetics, liquids such as water, etc

on or around the projector.

• Do not place metals, combustibles, etc on or around the projector.

• To avoid penetration of foreign objects, do not put the projector into a case

or bag together with any thing except the accessories of the projector,

signal cables and connectors.

Never disassemble and modify.

The projector contains high voltage components. Modification and/or disassembly of

the projector or accessories could result in fire or electrical shock.

• Never open the cabinet.

• Ask your dealer to repair and clean insider.

Do not give the projector any shock or impact.

If the projector should be shocked and/or broken, it could result in an injury,

and continued use could result in fire or electrical shock.

If the projector is shocked, immediately turn off the power switch, disconnect

the power plug from the power outlet and contact your dealer.

Do not place the projector on an unstable surface.

If the projector should be dropped and/or broken, it could result in an injury,

and continued use could result in fire or electrical shock.

• Do not place the projector on an unstable, slant or vibrant surface such as

a wobbly or inclined stand.

• Use the caster brakes placing the projector on a stand with casters.

• Do not place the projector in the side up position, the lens up position or

the lens down position.

• In the case of a ceiling installation or the like, contact your dealer before

installation.

Disconnect the

plug from the

power outlet.

Do not

disassemble.

3

WARNING

Be cautious of High temperatures of the projector.

High temperatures are generated when the lamp is lit. It could result in fire or

burn. Use special caution in households where children are present.

Do not touch about the lens, air fans and ventilation openings during use or

immediately after use, to prevent a burn. Take care of ventilation.

• Keep a space of 30 cm or more between the sides and other objects such

as walls.

• Do not place the projector on a metallic table or anything weak in heat.

• Do not place anything about the lens, air fans and ventilation openings of

the projector.

• Never block the air fan and ventilation openings.

• Do not cover the projector with a tablecloth, etc.

• Do not place the projector on a carpet or bedding.

Never look through the lens or openings when the lamp is on.

The powerful light could adversely affect vision.

Use special caution in households where children are present.

Use only the correct power cord and the correct power outlet.

Incorrect power supply could result in fire or electrical shock.

• Use only the correct power outlet depending on the indication on the

projector and the safety standard.

• The enclosed power cord must be used depending on the power outlet to

be used.

Be cautious of the power cord connection.

Incorrect connection of the power cord could result in fire or electrical shock.

• Do not touch the power cord with a wet hand.

• Check that the connecting portion of the power cord is clean (with no dust),

before using. Use a soft and dry cloth to clean the power plug.

• Insert the power plug into a power outlet firmly. Avoid using a loose,

unsound outlet or contact failure.

Be sure to connect with ground wire.

Connect the ground terminal of AC inlet of this unit with the ground terminal

provided at the building using the correct power cord; otherwise, fire or

electric shock can result.

• Don’t take the core of power cord away.

Safety Precautions (continued)

Surely connect

the ground wire.

4

WARNING

Be careful in handling the light source lamp.

The projector uses a high-pressure mercury glass lamp made of glass.

The lamp can break with a loud bang, or burn out. When the bulb bursts,

it is possible for shards of glass to fly into the lamp housing, and for gas

containing mercury to escape from the projector’s vent holes.

Please carefully read the section “Lamp”.

Be careful in handling the power cord and external connection

cables.

If you keep using a damaged the power cord or cables, it can cause a fire

or electrical shock. Do not apply too much heat, pressure or tension to the

power cord and cables.

If the power cord or cables is damaged (exposed or broken core wires, etc.),

contact your dealer.

• Do not place the projector or heavy objects on the power cord and cables.

Also, do not place a spread, cover, etc, over them because this could result

in the inadvertent placing of heavy objects on the concealed power cord or

cables.

• Do not pull the power cord and cables. When connecting and

disconnecting the power cord or cables, do it with your hand holding the plug

or connector.

• Do not place the cord near the heater.

• Avoid bending the power cord sharply.

• Do not attempt to work on the power cord.

Be careful in handling the battery of the remote control.

Incorrect handling of the battery could result in fire or personal injury. The

battery may explode if not handled properly.

• Keep the battery away from children and pets. If swallowed consult a

physician immediately for emergency treatment.

• Do not allow the battery in a fire or water.

• Avoid fire or high-temperature environment.

• Do not hold the battery with the metallic tweezers.

• Keep the battery in a dark, cool and dry play.

• Do not short circuit the battery.

• Do not recharge, disassemble or solder the battery.

• Do not give the battery a physical impact.

• Use only the battery specified in the other manual of this projector.

• Make sure the plus and minus terminals are correctly aligned when loading

the battery.

• If you observe a leakage of the battery, wipe out the flower and then

replace the battery. If the flower adheres your body or clothes, rinse well with

water.

• Obey the local laws on disposing the battery.

Safety Precautions (continued)

5

Safety Precautions (continued)

CAUTION

Be careful in moving the projector.

Neglect could result in an injury or damage.

• Do not move the projector during use. Before moving, disconnect the

power cord and all external connections, and close the slide lens door or

attach the lens cap.

• Avoid any impact or shock to the projector.

• Do not drag the projector.

• For moving the projector, use the enclosed case or bag if provided.

Do not put anything on top of the projector.

Placing anything on the projector could result in loss of balance or falling,

and cause an injury or damage. Use special caution in households where

children are present.

Do not attach anything other than specified things to the projector.

Neglect could result in an injury or damage.

• Some projector has a screw thread in a lens part. Do not attach anything

other than specified options (such as conversion lens) to the screw thread.

Avoid a smoky, humid or dusty place.

Placing the projector in a smoke, a highly humid, dusty place, oily soot or

corrosive gas could result in fire or electrical shock.

• Do not place the projector near a smoky, humid or dusty place (ex.

a smoking space, a kitchen, a beach, etc.). Do not place the projector

outdoors.

• Do not use a humidifier near the projector.

Take care of the air filter to normal ventilate.

The air filter should be cleaned periodically. If the air filter becomes clogged

by dust or the like, internal temperature rises and could cause malfunction.

The projector may display the message such as “CHECK THE AIR FLOW”

or turn off the projector, to prevent the internal heat level rising.

• When the indicators or a message prompts you to clean the air filter, clean

the air filter as soon as possible.

• If the soiling will not come off the air filter, or it becomes damaged, replace

the air filter.

• Use the air filter of the specified type only. Please order the air filter

specified in the other manual of this projector to your dealer.

• When you replace the lamp, replace also the air filter. The air filter may be

attached when you buy a replacement lamp for this projector.

• Do not turn on the projector without air filter.

Avoid a high temperature environment.

The heat could have adverse influence on the cabinet of the projector and

other parts. Do not place the projector, the remote control and other parts in

direct sunlight or near a hot object such as heater, etc.

Avoid Magnetism.

Manufacture strongly recommends to avoid any magnetic contact that is not

shielded or protected on or near the projector itself. (ie.,. Magnetic Security

Devices, or other projector accessory that contains magnetic material that has not

been provided by the manufacture etc.) Magnetic objects may cause interruption

of the projector's internal mechanical performance which may interfere with cooling

fans speed or stopping, and may cause the projector to completely shut down

.

6

Safety Precautions (continued)

NOTE

Do not give the remote control any physical impact.

A physical impact could cause damage or malfunction of the remote control.

• Take care not to drop the remote control.

• Do not place the projector or heavy objects on the remote control.

Take care of the lens.

• Close the slide lens door or attach the lens cap to prevent the lens surface being

scratched when the projector is not used.

• Do not touch the lens to prevent fog or dirt of the lens that cause deterioration of display

quality.

• Use commercially available lens tissue to clean the lens (used to clean cameras,

eyeglasses, etc.). Be careful not to scratch the lens with hard objects.

Take care of the cabinet and the remote control.

Incorrect care could have adverse influence such as discoloration, peeling paint, etc.

• Use a soft cloth to clean the cabinet and control panel of the projector and the remote

control. When excessively soiled dilute a neutral detergent in water, wet and wring out the

soft cloth and afterward wipe with a dry soft cloth. Do not use undiluted detergent directly.

• Do not use an aerosol sprays, solvents, volatile substances or abrasive cleaner.

• Before using chemical wipes, be sure to read and observe the instructions.

• Do not allow long-term close contact with rubber or vinyl.

About bright spots or dark spots.

Although bright spots or dark spots may appear on the screen, this is a unique characteristic of

liquid crystal displays, and such do not constitute or imply a machine defect.

Be careful of printing of the LCD panel.

If the projector continues projecting a still image, inactive images or 16:9 aspect images in

case of 4:3 panel, etc., for long time, the LCD panel might possibly be printed.

CAUTION

Remove the power cord for complete separation.

• For safety purposes, disconnect the power cord if the projector is not to be

used for prolonged periods of time.

• Before cleaning, turn off and unplug the projector. Neglect could result in

fire or electrical shock.

Ask your dealer to cleaning inside of the projector about every

year.

Accumulations of dust inside the projector cause result in fire or malfunction.

Cleaning inside is more effective if performed before every humid periods

such as rainy season.

• Do not clean inside yourself because it is dangerous.

Disconnect the

plug from the

power outlet.

7

Safety Precautions (continued)

NOTE

About consumables.

Lamp, LCD panels, polarizors and other optical components, and air filter and cooling fans

have a different lifetime in each. These parts may need to be replaced after a long usage

time.

• This product isn’t designed for continuous use of long time. In the case of continuous use

for 6 hours or more, or use for 6 hours or more every day (even if it isn’t continuous), or

repetitious use, the lifetime may be shortened, and these parts may need to be replaced

even if one year has not passed since the beginning of using.

• Any inclining use beyond the adjustment range explained in these user’s manuals may

shorten the lifetimes of the consumables.

Before turning on the power, make the projector cool down adequately.

After turning the projector off, pushing the restart switch or interrupting of the power supply,

make the projector cool down adequately. Operation in a high temperature state of the

projector causes a damage of the electrode and un-lighting of the lamp.

Avoid strong rays.

Any strong ray (such as direct rays of the sun or room lighting) onto the remote control

sensors could invalidate the remote control.

Avoid radio interference.

Any interfering radiation could cause disordered image or noises.

• Avoid radio generator such as a mobile telephone, transceiver, etc. around the projector.

About displaying characteristic.

The display condition of the projector (such as color, contrast, etc.) depends on

characteristic of the screen, because the projector uses a liquid crystal display panel. The

display condition can differ from the display of CRT.

• Do not use a polarized screen. It can cause red image.

Turn the power on/off in right order.

To prevent any trouble, turn on/off the projector in right order mentioned below unless

specifying.

• Power on the projector before the computer or video tape recorder.

• Power off the projector after the computer or video tape recorder.

Take care not to fatigue your eyes.

Rest the eyes periodically.

Set the sound volume at a suitable level to avoid bothering other people.

• It is better to keep the volume level low and close the windows at night to protect the

neighborhood environment.

Connecting with notebook computer

When connecting with notebook computer, set to valid the RGB external image output

(setting CRT display or simultaneous display of LCD and CRT).

Please read instruction manual of the notebook for more information.

8

• If the lamp should break (it will make a loud bang when it does), unplug

the power cord from the outlet, and make sure to request a replacement

lamp from your local dealer. Note that shards of glass could damage the

projector’s internals, or cause injury during handling, so please do not try to

clean the projector or replace the lamp yourself.

• If the lamp should break (it will make a loud bang when it does), ventilate

the room well, and make sure not to breathe the gas that comes out of the

projector vents, or get it in your eyes or mouth.

• Before replacing the lamp, make sure the power switch is off and the

power cable is not plugged in, then wait at least 45 minutes for the lamp to

cool sufficiently. Handling the lamp while hot can cause burns, as well as

damaging the lamp.

Lamp

The projector uses a high-pressure mercury glass lamp. The lamp can break with a

loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time.

Note that each lamp has a different lifetime, and some may burst or burn out soon after

you start using them. In addition, when the bulb bursts, it is possible for shards of

glass to fly into the lamp housing, and for gas containing mercury to escape from the

projector’s vent holes.

About disposal of a lamp • This product contains a mercury lamp; do not put in trash.

Dispose of in accord with environmental laws.

For lamp recycling, go to www.lamprecycle.org. (in USA)

For product disposal, contact your local government agency or www.eiae.org (in the US)

or www.epsc.ca (in Canada).

For more information, call your dealer.

• Do not open the lamp cover while the projector is suspended from above.

This is dangerous, since if the lamp’s bulb has broken, the shards will

fall out when the cover is opened. In addition, working in high places is

dangerous, so ask your local dealer to have the lamp replaced even if the

bulb is not broken.

• Do not use the projector with the lamp cover removed. At the lamp

replacing, make sure that the screws are screwed in firmly. Loose screws

could result in damage or injury.

• Use the lamp of the specified type only.

• If the lamp breaks soon after the first time it is used, it is possible that

there are electrical problems elsewhere besides the lamp. If this happens,

contact your local dealer or a service representative.

• Handle with care: jolting or scratching could cause the lamp bulb to burst

during use.

• Using the lamp for long periods of time, could cause it dark, not to light up

or to burst. When the pictures appear dark, or when the color tone is poor,

please replace the lamp as soon as possible. Do not use old (used) lamps;

this is a cause of breakage.

WARNING

HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE

Disconnect

the plug from

the power

outlet

9

Regulatory Notices

FCC Statement Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

WARNING: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the following

measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

- Consult the dealer or an experienced radio/TV technician for help.

INSTRUCTIONS TO USERS: This equipment complies with the requirements of FCC

(Federal Communication Commission) equipment provided that the following conditions

are met. Some cables have to be used with the core set. Use the accessory cable or a

designated-type cable for the connection. For cables that have a core only at one end,

connect the core to the projector.

CAUTION: Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

For the Customers in CANADA

NOTICE: This Class B digital apparatus complies with Canadian ICES-003.

Warranty And After-Service

Unless seen any abnormal operations (mentioned with the first paragraph of

WARNING in this manual), when a problem occurs with the equipment, first refer to the

“Troubleshooting” section of the “Operating Guide”, and run through the suggested checks.

If this does not resolve the problem contact your dealer or service company. They will tell

you what warranty condition is applied.

2

Contents

Introduction ...............3

Features . .....................3

Checking the contents of package

... 3

Part names . ...................4

Setting up . ................7

Arrangement ...................7

Connecting with your devices

.....10

Connecting to a power supply

.....16

Fastening the adapter cover ......

17

Using the security bar and slot . . . . 17

Remote control ............18

Installing the batteries ...........18

About the remote control signal . . . 19

Changing the frequency of remote

control signal ..................19

Using as a simple PC mouse & keyboard

. . 20

Power on/off . .............21

Turning on the power . ..........21

Turning off the power . ..........22

Operating . ...............23

Adjusting the volume ............23

Temporarily muting the sound .....23

Selecting an input signal .........24

Searching an input signal . .......25

Selecting an aspect ratio .........26

Adjusting the projector's elevator . . 27

Adjusting the zoom and focus .....27

Using the automatic adjustment feature

...28

Adjusting the position . ..........28

Correcting the keystone distortions

.. 29

Using the magnify feature ........30

Temporarily freezing the screen . . . 31

Temporarily blanking the screen . . 31

Using the menu function . .......32

EASY MENU. . . . . . . . . . . . . . . 34

A

SPECT

, A

UTO

KEYSTONE

,

K

EYSTONE

,

PICTURE MODE,

E

CO

MODE

, I

NSTALLATION

,

R

ESET

, F

ILTER

TIME

, L

ANGUAGE

,

A

DVANCED

MENU

, E

XIT

PICTURE menu . ...........36

B

RIGHTNESS

, C

ONTRAST

, G

AMMA

, C

OLOR

TEMP

,

COLOR, TINT, SHARPNESS, ACTIVE IRIS, MY MEMORY

IMAGE menu . .............39

A

SPECT

, O

VER

SCAN

, V

POSITION

, H

POSITION

,

H

PHASE

, H

SIZE

, A

UTO

ADJUST

EXECUTE

INPUT menu . .............42

PROGRESSIVE, VIDEO NR, COLOR SPACE,

V

IDEO FORMAT, HDMI FORMAT, HDMI RANGE,

C

OMPUTER IN, FRAME LOCK, RESOLUTION



SETUP menu ..............46

AUTO KEYSTONE,

K

EYSTONE, AUTO ECO MODE,

E

CO MODE,

I

NSTALLATION

, S

TANDBY

MODE

,

M

ONITOR

OUT

AUDIO menu . .............49

V

OLUME

, S

PEAKER

, A

UDIO

SOURCE

,

M

IC

LEVEL

, M

IC

VOLUME

SCREEN menu .............50

L

ANGUAGE

, M

ENU

POSITION

, B

LANK

,

S

TART

UP

,

M

yScreen

, M

yScreen Lock

,

M

ESSAGE

, S

OURCE

NAME

, T

EMPLATE

, C.

C

.

OPTION menu . ............56

A

UTO

SEARCH

, A

UTO

KEYSTONE

,

D

IRECT

POWER

ON

, A

UTO

POWER

OFF

,

L

AMP

TIME

, F

ILTER

TIME

, M

Y

BUTTON

,

M

Y

SOURCE

, S

ERVICE

NETWORK menu ...........67

W

IRELESS

SETUP

, W

IRELESS

INFORMATION

,

W

IRED

SETUP

, W

IRED

INFORMATION

,

P

ROJECTOR

NAME

, M

Y

IMAGE

, A

MX

D

.

D

.,

P

RESENTATION

, S

ERVICE

SECURITY menu ...........78

S

ECURITY

PASSWORD

CHANGE

,

M

yScreen

PASSWORD

, P

IN

LOCK

,

T

RANSITION

DETECTOR

, M

Y

TEXT

PASSWORD

,

M

Y

TEXT

DISPLAY

, M

Y

TEXT

WRITING

,

C

LONING

LOCK

Presentation tools . ........84

PC-LESS Presentation

...........84

Drawing Function

................

94

USB Display

(Windows computer)

.....

100

USB Display

(Mac computer)

.......

104

Maintenance .............108

Replacing the lamp ............108

Cleaning and replacing the air ﬁlter . 110

Other care ................... 112

Troubleshooting . .........113

Related messages . ........... 113

Regarding the indicator lamps . . . 115

Resetting all settings ........... 118

Phenomena that may be easy

to be mistaken for machine defects

.. 118

Speciﬁcations ............123



3

Introduction

• Keep the original packing materials, for future reshipment. Be sure

to use the original packing materials when moving the projector. Use special

caution for the lens.

• The projector may make a rattling sound when tilted, moved or shaken, since

a ﬂap to control the air ﬂow inside of the projector has moved. Be aware that

this is not a failure or malfunction.

NOTE

The projector provides you with the broad use by the following features.

Checking the contents of package

 This projector has a variety of I/O ports that supposedly cover for any

business scene. The HDMI port can support various image equipment which

have digital interface to get clearer pictures on a screen.

 If you insert a USB storage device, such as a USB memory, into the USB

TYPE A port and select the port as the input source, you can view images

stored in the device.

 This projector can be controlled and monitored via LAN connection.

Furthermore, you can use the designated USB wireless adapter (optional) to

establish wireless LAN connection.

 The double layer ﬁlter system is expected to function longer and offers

youless maintenance frequency.

 The built-in 16W speaker can deliver sufﬁcient sound volume in a large space

like a classroom without external speakers.

Please see the Contents of package section in the User’s Manual (concise)

which is a book. Your projector should come with the items shown there. Require

of your dealer immediately if any items are missing.

Features

►Keep small parts away from children and pets. Take care

not to put in the mouth. If swallowed, consult a physician immediately for

emergency treatment.

WARNING

4

Introduction

►Do not open or remove any portion of the product, unless the

manuals direct it.

►Do not subject the projector to unstable conditions.

►Do not apply a shock or pressure to this product.

►Do not look into the lens and the openings on the projector while the lamp is

on.

WARNING

►Do not touch around the lamp cover and the exhaust

vents during use or just after use, since it is too hot.

►Do not attach anything onto the lens except the lens cover of this

projector because it could damage the lens, such as melting the lens.

CAUTION

(continued on next page)

Part names

(1) Lamp cover (108)

The lamp unit is inside.

(2) Speaker (

23, 49)

(3) Filter cover (

110)

The air ﬁlter and intake vent are inside.

(4) Elevator feet (x2) (

27)

(5) Elevator buttons (x2) (

27)

(6) Remote sensor (

19)

(7) Lens (

112)

(8) Lens cover

(9) Intake vents

(10) Control panel (

5)

(11) FOCUS ring (

27)

(12) ZOOM ring (

27)

(13) AC IN (AC inlet) (

16)

(14) Exhaust vent

(15) Rear panel (

5)

(8)

(9)

(4)

(7)

(3)

(4)

(5)

(6)

(2)

(13)

(14)

(15)

(10)

(1)

(11)

(12)

(5)

5

Introduction

Part names (continued)

Control panel

(1) STANDBY/ON button (

21)

(2) INPUT button (

24)

(3) MENU button (

32)

(4) LAMP indicator (

115)

(5) TEMP indicator (

115)

(6) POWER indicator (

115)

Rear panel (



10 ~ 15)

(1) LAN port

(2) USB TYPE A port(x2)

(3) USB TYPE B port

(4) HDMI port

(5) MIC port (

15)

(6) AUDIO IN1 port

(7) AUDIO IN2 port

(8) AUDIO IN3 (R,L) ports

(9) AUDIO OUT (R,L) ports

(10) COMPUTER IN1 port

(11) COMPUTER IN2 port

(12) MONITOR OUT port

(13) CONTROL port

(14) VIDEO port

(15) S-VIDEO port

(16) Security slot (

17)

(17) Security bar (

17)

(continued on next page)

(1) (3)(2) (6)

(4)(5)

AUDIO IN

1

2

3

AUDIO OUT

(11)(10)(4)(3)(2)

(5)

(8)

(16)

(7)

(9) (14)

(13)

(12)

(1)

(15) (6)

(17)

6

Introduction

Part names (continued)

Remote control

(1) VIDEO button (

24)

(2) COMPUTER button (

24)

(3) SEARCH button (

25)

(4) STANDBY/ON button (

21)

(5) ASPECT button (

26)

(6) AUTO button (

28)

(7) BLANK button (

31)

(8) MAGNIFY - ON button (

30)

(9) MAGNIFY - OFF button (

30)

(10) MY SOURCE/DOC.CAMERA button

(

25, 59)

(11) VOLUME - button (

23)

(12) PAGE UP button (

20)

(13) PAGE DOWN button (

20)

(14) VOLUME + button (

23)

(15) MUTE button (

23)

(16) FREEZE button (

31)

(17) MY BUTTON - 1 button (

58, 59)

(18) MY BUTTON - 2 button (

58, 59)

(19) KEYSTONE button (

29)

(20) POSITION button (

28, 32)

(21) MENU button (

32)

(22) ▲/▼/◄/► cursor buttons (

32)

(23) ENTER button (

32)

(24) ESC button (

32)

(25) RESET button (

32)

(26) Battery cover (

18)

Back of

the remote control

(2)

(1)

(6)

(5)

(16)

(8)

(9)

(19)

(17)

(20)

(22)

(24)

(10)

(4)

(3)

(7)

(12)

(14)

(11)

(13)

(15)

(18)

(21)

(23)

(25)

(26)

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

SEARCH

BLANK

MUTE

MY BUTTON

POSITION

ESC

MENU

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

ON

OFF

FREEZE

UP

࡯

㧗

VOLUME





ENTER

7

Setting up

Install the projector according to the environment and manner the projector will be

used in.

For the case of installation in a special state such as ceiling mount, the speciﬁed

mounting accessories (

Speciﬁcations in the User’s Manual (concise)) and

service may be required. Before installing the projector, consult your dealer about

your installation.

Arrangement

Refer to tables T-1,T-2 and T-3 at the back of User's Manual (concise) as well as

the following to determine the screen size and projection distance.

The values shown in the table are calculated for a full size screen.

(continued on next page)

• If the projector is used at an altitude of about 1600 m (5250 feet) or higher,

set ALTITUDE of the SERVICE item in the OPTION menu to HIGH (

59).

Otherwise, set it to NORMAL. If the projector is used with a wrong setting, it may

cause damage to the projector itself or the parts inside.

a Screen size (diagonal)

b Projection distance (±10%, from the projector’s end)

c1 , c2 Screen height (±10%)

8

Setting up

Arrangement (continued)

WARNING

(continued on next page)

►Install the projector where you can access the power

outlet easily. If an abnormality should occur, unplug the projector urgently.

Otherwise it could cause a ﬁre or electric shock.

►Do not subject the projector to unstable conditions. If the projector falls

or topples over, it could result in injury or damage to the projector and the

surrounding things. Using a damaged projector could result in a ﬁre and an

electric shock.

• Do not place the projector in unstable places, such as an inclined surface,

places subject to vibration, on top of a wobbly table or cart, or a surface that is

smaller than the projector.

• Do not put the projector on its side, front or rear position.

• Do not attach nor place anything on the projector unless otherwise speciﬁed in

the manual.

• Do not use any mounting accessories except the accessories speciﬁed by the

manufacturer. Read and keep the manuals of the accessories used.

• For special installation such as ceiling mounting, be sure to consult your dealer

beforehand.

►

Do not install the projector near thermally conductive or ﬂammable

things. Such things when heated by the projector could result in a ﬁre and burns.

• Do not place the projector on a metal stand.

►Do not place the projector where any oils, such as cooking or machine

oil, are used. Oil may harm the product, resulting in malfunction, or falling from

the mounted position.

►Do not place the projector in a place where it may get wet. Getting the

projector wet or inserting liquid into the projector could cause a ﬁre and an

electric shock, and damage the projector.

• Do not place the projector near water, such as in a bathroom, kitchen, or

poolside.

• Do not place the projector outdoors or by the window.

• Do not place anything containing liquid near the projector.

9

Setting up

Arrangement (continued)

►Place the projector in a cool place with sufﬁcient

ventilation. The projector may shutdown automatically or may malfunction if its

internal temperature is too high.

Using a damaged projector could result in a ﬁre and an electric shock.

• Do not place the projector in direct sunlight or near hot objects such as heaters.

• Do not place the projector where the air from an air conditioner or similar unit

will blow on it directly.

• Keep a space of 30 cm or more between a side of the projector and other

objects such as walls.

• Do not place the projector on carpet, cushions or bedding.

• Do not stop up, block nor cover the projector's vent holes. Do not place

anything around the projector that could be sucked in or stuck to the projector's

intake vents.

• Do not place the projector at places that are exposed to magnetic ﬁelds, doing

so can cause the cooling fans inside the projector to malfunction.

►Avoid placing the projector in smoky, humid or dusty place. Placing the

projector in such places could cause a ﬁre, an electric shock and malfunction of

the projector.

• Do not place the projector near humidiﬁers. Especially for an ultrasonic

humidiﬁer, chlorine and minerals contained in tap water are atomized and could

be deposited in the projector causing image degradation or other problems.

• Do not place the projector in a smoking area, kitchen, passageway

or by the window.

• Position the projector to prevent light from directly hitting the projector's remote

sensor.

• Do not place the product in a place where radio interference may be caused.

• Check and correct the setting for ALTITUDE of SERVICE in the OPTION menu

according to the usage environment (

59). If the projector is used with a wrong

setting, it may cause damage to the projector itself or the parts inside.

• Keep heat-sensitive things away from the projector. Otherwise, they may be

damaged by the heat from the projector.

CAUTION

NOTICE

10

Setting up

Connecting with your devices

Before connecting the projector to a device, consult the manual of the device to

conﬁrm that the device is suitable for connecting with this projector and prepare

the required accessories, such as a cable in accord with the signal of the device.

Consult your dealer when the required accessory did not come with the product or

the accessory is damaged.

After making sure that the projector and the devices are turned off, perform

the connection, according to the following instructions. Refer to the ﬁgures in

subsequent pages.

Before connecting the projector to a network system, be sure to read Network

Guide too.

►Use only the appropriate accessories. Otherwise it could

cause a ﬁre or damage the projector and devices.

• Use only the accessories speciﬁed or recommended by the projector’s

manufacturer. It may be regulated under some standard.

• Neither disassemble nor modify the projector and the accessories.

• Do not use the damaged accessory. Be careful not to damage the accessories.

Route a cable so that it is neither stepped on nor pinched out.

WARNING

►For a cable with a core at only one end, connect the end

with the core to the projector. That may be required by EMI regulations.

CAUTION

• Do not turn on or off the projector while connected to a device in

operation, unless that is directed in the manual of the device. Otherwise it may

cause malfunction in the device or projector.

• The function of some input ports can be selected according to your usage

requirements. Check the reference page indicated beside each port in the

following illustration.

• Be careful not to mistakenly connect a connector to a wrong port. Otherwise it

may cause malfunction in the device or projector.

- When connecting a connector to a port, make sure that the shape of the

connector ﬁts the port.

- Tighten the screws to connect a connector equipped with screws to a port.

- Use the cables with straight plugs, not L-shaped ones, as the input ports of

the projector are recessed.

NOTE

(continued on next page)

11

Setting up

• Plug-and-Play is a system composed of a computer, its operating system

and peripheral equipment (i.e. display devices). This projector is VESA DDC

2B compatible. Plug-and-Play can be used by connecting this projector to a

computer that is VESA DDC (display data channel) compatible.

-

Take advantage of this feature by connecting a computer cable to the

COMPUTER IN1 port (DDC 2B compatible). Plug-and-Play may not work

properly if any other type of connection is attempted.

-

Please use the standard drivers in your computer as this projector is a Plug-

and-Play monitor.

About Plug-and-Play capability

(continued on next page)

Connecting with your devices (continued)

Page is loading ...

Hitachi CP-WX3015WN User manual

This manual is also suitable for

Hitachi CP-WX3015WN User manual

Other documents