Aquilon RS2 - Ref. AQL-RS2
QUICK START GUIDE
Thank you for choosing Analog Way and the Aquilon RS2. By following these simple steps, you will be able
to set up and use your 4K/8K mul-screen presentaon system and videowall processor within minutes.
Discover the Aquilon RS2 capabilies and intuive interface while commanding top-notch presentaons and
unleash your creavity for a new experience in show and event management.
• 1 x Aquilon RS2 (AQL-RS2)
• 2 x Power supply cords
• 1 x Ethernet cross cable (for device control)
• 3 x MCO 5-pin connectors
• 1 x Web-based Remote Control Soware included and hosted on the device
• 1 x Rack mount kit (the parts are stowed in the packaging foam)
• 1 x User Manual (PDF version)*
• 1 x Quick start guide*
* User Manual and quick start guide are also available on www.analogway.com
The Aquilon RS2 uses standard ethernet LAN
networking. To access the Web RCS, connect a
computer to the Aquilon RS2 using the Ethernet
cable. Then on the computer, open an internet
browser (Google Chrome is recommended).
Into this internet browser, enter the IP address
of the Aquilon RS2 displayed on the front panel
screen (192.168.2.140 by default).
The connecon starts.
Oen, computers are set to DHCP client (automac
IP detecon) mode. You may need to change the
IP address conguraon on your computer before
you can connect. These sengs are found in the
properes for your LAN network adaptor, and vary
by operang system.
The default IP address on the Aquilon RS2 is
192.168.2.140 with a netmask of 255.255.255.0.
Therefore, you can assign your computer a stac
IP address of 192.168.2.100 and a netmask of
255.255.255.0 and should be able to connect.
If the connecon is not starng:
• Be sure the computer IP address is on the same
network and subnet as the Aquilon RS2.
• Be sure that two devices do not have the same IP
address (prevent IP conicts)
• Check your network cable. You will need a
crossover ethernet cable if you are connecng
directly from the Aquilon RS2 to the computer. If
a hub or switch is involved, use straight ethernet
cables.
• For more informaon, please refer to the User
Manual or contact Analog Way Technical Support.
Go on our website to register your product(s)
hp://bit.ly/AW-Register
WHAT’S IN THE BOX
QUICK SETUP & OPERATION
CAUTION!
The use of rear rack support
slide rails for all rack mounted
applicaons is highly recom-
mended. Damage caused by
improper rack mounng will not
be covered under warranty.
Register
your product
- 8 x HDMI 2.0
- 4 x DisplayPort 1.2
- 4 x 12G-SDI (also compable
3G-SDI and 6G-SDI)
Output #1 to #12
- 12 x HDMI 2.0
100-240 VAC; 12-7A; 50/60Hz;
redundant power supplies (1+1), hot
swappable, max consumpon: 700W
2 x USB Plugs
- 2 x HDMI 2.0
The user should avoid disconnecng the power source
(AC input) unl the unit is in stand-by mode. Failure to
do this could result in hard drive data corrupon.
USB PlugsOLED display
Press once and conrm with
Enter buon for stand-by mode.
Conrm the menu or command
The IP address can be changed from
the front panel in the Control menu.
Analog Frame Lock input
and loop output
Tally / GPI-O
Dante™
- Dante audio primary and secondary RJ45 Gigabit Ethernet connectors
Ethernet Plug for unit control
(Web RCS or API)
Home menu or back one level
Menu scroll knob
Used for eect sync in mul-machine mode
OPERATION OVERVIEW
LIVE
Set Screens and Aux Screens layer sengs (content,
size, posion, borders, transions, etc.).
Set Mulviewers widgets sengs (content, size,
and posion).
SETUP
Setup assistant for adjusng all basic setups.
Set Mulviewers signal sengs (Custom resolu-
on and rate), paerns or image adjustment.
Set Outputs signal sengs (HDCP, custom resoluon
and rate), paerns or image adjustment.
Set Inputs signal sengs (resoluon and rate), paerns,
image adjustment, cropping and keying. It is also possible to
Freeze or Black an input.
Import images in the unit. Then load them as image pre-
sets to be used in layers.
Create and manage up to 16 custom formats.
Create and manage EDIDs.
Manage Dante Audio and audio roung.
Timers and GPIO.
Set the Internal rate, Framelock, Audio rate, etc.
Enable one or two Mulviewers.
Screens / Aux Screns
Enable Screens and Aux Screens.
Select the layer mode per screen (see below).
Set outputs capacity.
Assign outputs to Screens using drag and drop.
Add layers to Screens and set their capacity.
In Split layers mode, double the number of layers displayed on
Program. (Transions are limited to Fade or Cut. Mulviewers
widgets display Preview in wireframe only).
WEB RCS MENUS
Posion the outputs in a virtual screen to create the Canvas.
- Set Auto or custom Canvas size.
- Set Outputs resoluon and posion.
- Set Area of Interest (AOI).
- Set Blending
Inputs
Set capacity and allow inputs to output Background sets.
Set capacity and allow images to output Background sets.
Select allowed Inputs and Images to create up to 8 Background
sets per Screen to be used in Live.
LIVE
Create presets in LIVE > Screens and .
• Set layer size and posion in Preview or Program by clicking and
dragging the layer.
• Drag sources into layers from the le panel or select them in
layer properes.
• Set transions and use the Take buon to send the Preview
conguraon to Program
For more layers sengs, please refer to the LivePremier User
Manual.
A Mulviewer can display up to 24 Widgets that act like Screen
layers. A Widget content can be a program, preview, input, image
or mer.
MEMORIES
Once a preset is built, save it as one of the 1000 Screen memory
slots the Aquilon RS2 oers.
• Click , lter what to save and select a Memory.
• Load a preset at any me on Program or Preview by clicking on
the preset number or using drag and drop the preset into the
Program or Preview windows.
Export and Import conguraons from the Web RCS or Front
panel.
Save conguraons directly in the unit.
Update the unit rmware easily from the Web RCS or from the
Front panel.
Use a source as a mask for a Cut & Fill eect.
Keying
Apply Chroma or Luma Keying on an Input.
Use Master Memory to load mulple Screen presets.
For complete details and operaons procedures, please refer to
the LivePremier User Manual and our website:
01-JULY-2020
AQL-RS2 - QSG
Code : 140196
SETUP
LIVE
WEB RCS STRUCTURE
The menus are the essenal
steps to setup the show. Add Screens and
Layers while assigning desired capacies.
The assistant is here to help seng the unit
step by step.
In the other SETUP menus, manage Signal
and Image sengs for Mulviewers,
Outputs and Inputs. Add images, create
custom formats, set Dante Audio roung.
In the LIVE menus, set content for Screens,
Aux Screens and Mulviewers. Set Layer
sengs (size, posion, transions, etc.),
manage screen memories and trigger
transions between Preview and Program
Screens.
For complete details and operaons procedures, please refer to the User Manual and our
website for further informaon:
This Analog Way product has a 3 year warranty on parts and labor (back to factory), excluding I/O connector
cards which are warranted for 1 year. Broken connectors are not covered by warranty. This warranty does
not include faults resulng from user negligence, special modicaons, electrical surges, abuse (drop/crush),
and/or other unusual damage. In the unlikely event of a malfuncon, please contact your local Analog Way
oce for service.
WARRANTY AND SERVICE
-
1
-
2
-
3
-
4
Analog way Aquilon RS1 Quick start guide
- Type
- Quick start guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Analog way Aquilon C User manual
-
Analog way Aquilon C Quick start guide
-
-
-
-
-
-
Analog way QuickMatrix 4K User manual
-
-
Other documents
-
Boss Office Products B6022 Operating instructions
-
Pro-Ject Audio System RS2 Power Box User manual
-
Extron Quantum Ultra User manual
-
Belden RS2-TX User manual
-
Glensound BEATRICE MIX32 Owner's manual
-
Hasbro 42622 User manual
-
Pro-Ject Pre Box RS2 Digital Pre Box RS2 Brochüre (Englisch)
-
Miranda Kaleido-X16 User manual
-
Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - AQL EVENT AND FLOW QUERY CLI GUIDE User manual
-
Barco EC-200 User guide
