ITEM #0803908
MODEL #LWFT1658
RECHARGEABLE HEADLAMP
UTILITECH & UT Design® is a registered
trademark of LF, LLC.All Rights Reserved.
PACKAGE CONTENTS
x 1 x 1
x 1
Headlamp Headband
Micro USB Cable
IDEAL FOR RUNNING & READING & MORE
LAMP OPERATION/LAMP OPERATION/LAMP OPERATION
Removeable Head band at your prefer. Removeable Head band Clip for holding or releasing the earphone.
2
5
3
4
1
4
5
Bluetooth ON/OFF
&
Play/Pause Button
Volume Up
/Next Button
Volume Down
/Back Button
Bluetooth Indicator
Light
Recharge Indicator
Light
When the Bluetooth is turned on, the Bluetooth LED begins
flashing blue indicating the system is in Bluetooth pairing mode.
The Bluetooth LED turns solid blue and plays a “du-du” sound in
the earphone when it has successfully paired with a Bluetooth
device.
The indicator light flashing red when it is charged, and will
be solid red after fully charged.
Press and hold the button to turn on & turn off the Bluetooth.
Press the button once quickly to pause sound. Press quickly
once again to continue sound.
Press and hold the button to increase the volume and release the
button to finish. Press the button once quickly for the next setting
mode.
1
2
3
Press and hold the button to increase the volume and release
the button to finish. Press the button once quickly for the previous
setting mode.
Note: Press switch at any selected modes to turn off while working after 3 seconds.
*
1X
Full Light
2X
Proximity Light
3X
Distance Light
4X
OFF
Depress & hold the button for dimming function at any selected modes.
DIM
#
Name
Description
Solid Red
1X
Red Flashing
2X
OFF
3X
CAUTION: This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
approved by the party responsible for compliance could void the user’s authority to operate the equipment.
WARNING
1. This headlamp projects a very bright beam of light. For eye protection, do not look directly into the light.
2. This product is powered by a lithium-ion rechargeable battery. Never expose the battery to any liquid or fire.
3. Never disassemble the unit or attempt to remove battery, as that could cause leakage of alkaline solution or other electrolytic substance.
4. Never use or charge the battery if it appears to be leaking, discolored, deformed or abnormal.
5. Dispose of batteries according to local regulations. Please recycle when possible. Do not dispose as household waste or in a fire.
SAFETY INFORMATION
BLUETOOTH OPERATION
1 STREAMING AUDIO WIRELESSLY USING A BLUETOOTH DEVICE
To wirelessly stream audio to this headlamp from a Bluetooth-enabled device:
Press and hold the button (1) to turn on the Buletooth and the Bluetooth LED (4) will begin flashing blue.
Place a Bluetooth-capable device in the pairing mode. Use the device’s Bluetooth pairing menu to pair with this headlamp (Pairing name:
LED HEADLAMP).
When the Bluetooth LED (4) illuminates blue continually, it is paired with the device and you can stream audio via Bluetooth from your device
to the headlamp.
2 DISCONNECTING A BLUETOOTH DEVICE
Press and hold the button (2) & (3) together to disconnect a Bluetooth device.
To pair this headlamp with a different Bluetooth-enable device, repeat Step 1
with the new device.
The bluetooth LED will turn off automaticlly if there is no connecting within
about 15 minutes.
CHARGING OPERATION
+ 40°C / + 104°F
+ 0°C / + 32°F
Note: Charging while using a USB wall adaptor will be faster than a computer USB port.
*
Remove USB cable from the device once LED changes
from solid red to red flashing and close USB door.
2000mAh Rechargeable Battery
USB 5V
(not included)
(not included)
IMPORTANT: The speaker will play continous “beep”
sounds when the power is low. The Bluetooth LED will then
turn off automatically. When this occurs, you must charge the
Bluetooth headlamp.
□
□
□
□
□
□
□
Reorient or relocate the receiving antenna.
□ Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
□
□
Consult the dealer or an experienced radio/TV technician for help.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
/