Duerkopp Adler 911-210 User manual

Type
User manual

Duerkopp Adler 911-210 offers advanced stitch position optimization, allowing you to prevent festoon stitch formation by guiding the hook thread to the left of the stitch hole. Easily assembled, it features adjustable eccentrics for precise control of the hook thread pusher's path. Activate and deactivate stitch position optimization through technology points in sewing programs or via contour adjustment on the control panel.

Duerkopp Adler 911-210 offers advanced stitch position optimization, allowing you to prevent festoon stitch formation by guiding the hook thread to the left of the stitch hole. Easily assembled, it features adjustable eccentrics for precise control of the hook thread pusher's path. Activate and deactivate stitch position optimization through technology points in sewing programs or via contour adjustment on the control panel.

906
911-210
Additional Instructions
Stitch position optimization
All rights reserved.
Property of Dürkopp Adler AG and protected by copyright. Any reuse of these contents,
including extracts, is prohibited without the prior written approval of Dürkopp Adler AG.
Copyright © Dürkopp Adler AG 2020
IMPORTANT
READ CAREFULLY BEFORE USE
KEEP FOR FUTURE REFERENCE
Table of Contents
Additional Instructions 906/911-210 - 02.0 - 05/2020 1
1 General information ................................................................... 3
2 Assembling the stitch position optimization ........................... 4
2.1 Assembling the magnet valve....................................................... 4
2.2 Assembling the stitch position optimization .................................. 6
2.3 Checking the stitch position optimization...................................... 7
2.4 Programming the stitch position optimization ............................... 8
Table of Contents
2 Additional Instructions 906/911-210 - 02.0 - 05/2020
General information
Zusatzanleitung 906/911-210 - 02.0 - 05/2020 3
1 General information
Multi-directional stitching paths lead to difficulties with unreeling direc-
tions. This may result in the hook thread forming a festoon stitch i.e. dou-
ble plaiting of the needle thread.
To prevent this festoon stitch occurring, stitch position optimization can be
activated so the hook thread is guided to the left of the stitch hole. This will
result in the needle always making the stitch to the right of the hook thread,
thereby avoiding a festoon stitch.
Components of the kit
Check whether the scope of delivery for kit 0911 597774 is correct prior to
installation.
Part number Quantity Description
0911 597764 1 Stich position optimization, fitted
9710 063000 1 Magnet valve
9731 005004 1 Hose (3,6 m)
9840 121001 5 Cable tie
0791 911862 EN 1 Additional Instructions
Assembling the stitch position optimization
4 Zusatzanleitung 906/911-210 - 02.0 - 05/2020
2 Assembling the stitch position optimization
2.1 Assembling the magnet valve
Fig. 1: Assembling the magnet valve (1)
To assemble the magnet valve:
1. Remove the blanking plates from the valve block.
2. Assemble the magnet valve (1).
Class 906: output 7
Class 911-210: output 8
NOTICE
Property damage may occur!
The hoses can be damaged by contact with rotating shafts or moving
parts.
Fix the hoses with cable ties. Cut off protruding cable ties.
(1) - Magnet valve
Assembling the stitch position optimization
Zusatzanleitung 906/911-210 - 02.0 - 05/2020 5
Fig. 2: Assembling the magnet valve (2)
3. Guide hoses (2) downwards between the rear hood of the machine
head and the carrier of the transport system.
4. Secure hoses (2) with the cables ties to the existing cables and hoses
and guide them forwards to the hook.
(2) - Hoses
Assembling the stitch position optimization
6 Zusatzanleitung 906/911-210 - 02.0 - 05/2020
2.2 Assembling the stitch position optimization
The path of the hook thread slider (2) is limited by two eccentrics (1). The
eccentrics (1) can be adjusted when installed.
Fig. 3: Assembling the stitch position optimization
To assemble the stitch position optimization:
1. Disassemble the throat plate holder (4).
2. Disassemble the throat plate (3) and needle guide (5).
3. Screw throat plate (3) and needle guide (5) to stitch position optimiz-
ation (6).
4. Assemble the stitch position optimization (6) in the machine.
Important
Check the setting of the needle guide ( Service Instructions).
The hook thread pusher (2) should have the smallest possible dis-
tance to the throat plate underside, but should NOT touch the throat
plate underside.
5. Tighten the stitch plate optimization
(1) - Eccentric
(2) - Hook thread pusher
(3) - Throat plate
(4) - Throat plate holder
(5) - Needle guide
(6) - Stitch position optimization
Assembling the stitch position optimization
Zusatzanleitung 906/911-210 - 02.0 - 05/2020 7
Important
When folding down the machine head, make sure that the stitch position
optimization does NOT hit the oil pan.
If necessary, bend the oil pan slightly forward.
2.3 Checking the stitch position optimization
Fig. 4: Checking the stitch position optimization
To check the stitch position optimization:
1. In the menu Service > Multitest > Test outputs activate
the magnet valve.
Class 906: activate output 7
Class 911-210: activate output 8
The path of the hook thread pusher to the center of the stitch hole is
limited by the two eccentrics so that the hook thread is diverted to the
left via the center of the stitch hole.
Stitch position optimization Stitch position optimization
active inactive
Assembling the stitch position optimization
8 Zusatzanleitung 906/911-210 - 02.0 - 05/2020
2.4 Programming the stitch position optimization
Fig. 5: Programming the stitch position optimization
To program the stitch position optimization:
1. Control stitch direction optimization via technology points in the sewing
program (e.g. DA-CAD).
Class 906:
Output 7 ON: Stitch position optimization active
Output 7 OFF: Stitch position optimization inactive
Class 911-210:
Output 8 ON: Stitch position optimization active
Output 8 OFF: Stitch position optimization inactive
OR
1. Switch stitch direction optimization on or off via the contour adjustment
on the control panel.
(1) - Stitch position optimization active (2) - Stitch position optimization inactive
DÜRKOPP ADLER AG
Potsdamer Str. 190
33719 Bielefeld
Germany
Phone: +49 (0) 521 925 00
www.duerkopp-adler.com
Subject to design changes - Part of the machines shown with additional equipment - Printed in Germany
© Dürkopp Adler AG - Additional Instructions - 0791 911682 EN - 02.0 - 05/2020
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Duerkopp Adler 911-210 User manual

Type
User manual

Duerkopp Adler 911-210 offers advanced stitch position optimization, allowing you to prevent festoon stitch formation by guiding the hook thread to the left of the stitch hole. Easily assembled, it features adjustable eccentrics for precise control of the hook thread pusher's path. Activate and deactivate stitch position optimization through technology points in sewing programs or via contour adjustment on the control panel.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI