Tapco Max Snap Stand Operating instructions
- Type
- Operating instructions
Max Snap Stand
™
Item # 11957
T4043 7/04
29797 Beck Road • Wixom, MI 48393-2834
phone: (800) 521-7567 • www.tapcoint.com
TAPCO PRODUCTS COMPANY
A Division of Tapco International
Operating Instructions
©2004 Tapco International Corporation
S n a p S t a n d
S n a p S t a n d
M a x S n a p S t a n d
Counter Balance Assembly Instructions
4
Contents
Setting up your
Max Snap Stand .................. 2
Installing a Brake on your
Max Snap Stand ...............2-3
Removing Brake from
Max Snap Stand .................. 3
Counter Balance Step
Assembly Instructions ........ 4
Removal is the reverse of assembly. Lift up on the steps to release them from the
legs, and slide the assembly to the right until the connectors are free of the legs.
STEP 1
Attach the Connectors to the Steps using the carriage bolts and nuts provided. The square
portion of the carriage bolt will fall into the square holes that are punched in the Connector.
Tighten securely using a 7/16" wrench. See figure 5 above for Connector orientation.
Connector
STEP 2
To attach the Step Assembly to the Snap Stand, hold the assembly at an angle as shown and slide both
connectors leftward over both legs of the Snap Stand as far as they will go. Allow the connectors to slip
down the legs until the steps are fl at and touching the ground. The connectors should be gripping the front
and back of each leg. Standing on the steps while bending will lock the connectors in place on the legs.
Step
TOP
UNDERSIDE
Figure 5
Figure 5
T4043 Max Snap Stand Inst.indd 2-3 8/18/04 2:32:35 PM
S n a p S t a n dM a x S n a p S t a n d
Setting up your Max Snap Stand
™
S n a p S t a n d
M a x S n a p S t a n d
Installing a Max Brake on Max Snap Stand
™
32
STEP 1
To open each Leg Set, push in on the snap button and
move each leg outward to the working position. Figure
1A above shows the leg set as shipped while Figure 1B
shows the leg set open (working position). Make sure
button snaps out to lock each leg.
Snap button
Snap button
is toward the
is toward the
working side
working side
of brake
of brake
STEP 2
Attach the Cross Braces to the Leg Sets. With the
snap button of the Leg Set pointing to the outside,
snap the Cross Braces into position. See Figures
2A and 2B above.
Be sure the C-shape of the Cross Brace is mating
the leg as shown in Figure 2C above.
Figure 1A
Figure 1B
Figure 2A
Figure 2B
Figure 2C
Snap Button locations
when legs are closed.
Snap Button locations
when legs are open.
STEP 2
The snap button will
be toward the working
side of the brake.
Repeat Step 1 for the
other Leg Set. Be sure
that both ends of the
Snap Stand are going the
same direction (with the
snap buttons on the same
side). See Figure 2 at left.
Installing a Brake on Max Snap Stand
™
STEP 1
STEP 1
Using the 1/4-20 bolts and lock
washers provided, fasten the
brake mounts to the Leg Set.
STEP 3
Place the brake on the
assembled Snap Stand
with the Back Rail of the
brake clearing the adaptor
hook as shown in Figures
3A and 3B above.
Figure 2
Figure 3A Figure 3B
Back Rail clearing
adaptor hook
The snap button will be covered by the fi xed
hinge of the brake as in Figure 3C above.
Figure 3C
Removing a Brake from Max Snap Stand
™
- Removing the brake from the Snap Stand is essentially the
opposite of attaching it to the stand.
- Lifting the Moving Hinge, depress the snap button and pull the
brake forward far enough to hold each snap button down.
- Be sure the box rail is out of the Rear Clip. The brake can now
be removed from the stand.
- Reverse Steps 2 and 1 to disassemble the stand for transport.
Figure 4
Button pops up when
brake is fully seated
STEP 4
Push the brake fi rmly rearward into
the adaptor hooks. The snap buttons
by the front clips will pop up and
secure the brake on the Snap Stand.
See Figure 4 above.
Counter Balance is required
for operation. See installation
instructions on page 4.
T4043 Max Snap Stand Inst.indd 4-5 8/18/04 2:32:39 PM
S n a p S t a n dM a x S n a p S t a n d
Setting up your Max Snap Stand
™
S n a p S t a n d
M a x S n a p S t a n d
Installing a Max Brake on Max Snap Stand
™
32
STEP 1
To open each Leg Set, push in on the snap button and
move each leg outward to the working position. Figure
1A above shows the leg set as shipped while Figure 1B
shows the leg set open (working position). Make sure
button snaps out to lock each leg.
Snap button
Snap button
is toward the
is toward the
working side
working side
of brake
of brake
STEP 2
Attach the Cross Braces to the Leg Sets. With the
snap button of the Leg Set pointing to the outside,
snap the Cross Braces into position. See Figures
2A and 2B above.
Be sure the C-shape of the Cross Brace is mating
the leg as shown in Figure 2C above.
Figure 1A
Figure 1B
Figure 2A
Figure 2B
Figure 2C
Snap Button locations
when legs are closed.
Snap Button locations
when legs are open.
STEP 2
The snap button will
be toward the working
side of the brake.
Repeat Step 1 for the
other Leg Set. Be sure
that both ends of the
Snap Stand are going the
same direction (with the
snap buttons on the same
side). See Figure 2 at left.
Installing a Brake on Max Snap Stand
™
STEP 1
STEP 1
Using the 1/4-20 bolts and lock
washers provided, fasten the
brake mounts to the Leg Set.
STEP 3
Place the brake on the
assembled Snap Stand
with the Back Rail of the
brake clearing the adaptor
hook as shown in Figures
3A and 3B above.
Figure 2
Figure 3A Figure 3B
Back Rail clearing
adaptor hook
The snap button will be covered by the fi xed
hinge of the brake as in Figure 3C above.
Figure 3C
Removing a Brake from Max Snap Stand
™
- Removing the brake from the Snap Stand is essentially the
opposite of attaching it to the stand.
- Lifting the Moving Hinge, depress the snap button and pull the
brake forward far enough to hold each snap button down.
- Be sure the box rail is out of the Rear Clip. The brake can now
be removed from the stand.
- Reverse Steps 2 and 1 to disassemble the stand for transport.
Figure 4
Button pops up when
brake is fully seated
STEP 4
Push the brake fi rmly rearward into
the adaptor hooks. The snap buttons
by the front clips will pop up and
secure the brake on the Snap Stand.
See Figure 4 above.
Counter Balance is required
for operation. See installation
instructions on page 4.
T4043 Max Snap Stand Inst.indd 4-5 8/18/04 2:32:39 PM
Max Snap Stand
™
Item # 11957
T4043 7/04
TAPCO PRODUCTS COMPANY
29797 Beck Road • Wixom, MI 48393-2834
phone: (800) 521-7567
Tapco Products Company
Operating Instructions
S n a p S t a n d
S n a p S t a n d
M a x S n a p S t a n d
Counter Balance Assembly Instructions
4
Contents
Setting up your
Max Snap Stand .................. 2
Installing a Brake on your
Max Snap Stand ...............2-3
Removing Brake from
Max Snap Stand .................. 3
Counter Balance Step
Assembly Instructions ........ 4
Removal is the reverse of assembly. Lift up on the steps to release them from the
legs, and slide the assembly to the right until the connectors are free of the legs.
STEP 1
Attach the Connectors to the Steps using the carriage bolts and nuts provided. The square
portion of the carriage bolt will fall into the square holes that are punched in the Connector.
Tighten securely using a 7/16" wrench. See fi gure 5 above for Connector orientation.
Connector
STEP 2
To attach the Step Assembly to the Snap Stand, hold the assembly at an angle as shown and slide both
connectors leftward over both legs of the Snap Stand as far as they will go. Allow the connectors to slip
down the legs until the steps are fl at and touching the ground. The connectors should be gripping the front
and back of each leg. Standing on the steps while bending will lock the connectors in place on the legs.
Step
TOP
UNDERSIDE
Figure 5
Figure 5
T4043 Max Snap Stand Inst.indd 2-3 8/18/04 2:32:35 PM
© Boral Building Products Inc.
-
1
-
2
-
3
-
4
Tapco Max Snap Stand Operating instructions
- Type
- Operating instructions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Builders Edge 050010108009 Operating instructions
-
Invacare Action 5 User manual
-
Etac Cross 5 User manual
-
-
-
Maytag MAV6200 User manual
-
NordicTrack WalkFit Classic Owner's manual
-
Pride Quantum 1650 Owner's manual
-
-
Chrysler Dodge Monaco 1966 User manual