Sytech SYAC700 Owner's manual

Brand: Sytech

Model: SYAC700

Category: Mobile air conditioners

Type: Owner's manual

Sytech SYAC700 is a portable air conditioner that provides cooling, dehumidification, and fan-only functions. It is suitable for both home and office use.

Capabilities:

Cooling: Cools the air in a room to a temperature between 16°C and 30°C.
Dehumidification: Removes excess moisture from the air, creating a more comfortable environment.
Fan-only: Circulates the air in a room without cooling or dehumidifying it.

Features:

Two fan speeds: Choose between high and low fan speeds to adjust the airflow.
24-hour programmable timer: Set the unit to turn on or off at specific times.

Sytech SYAC700 is a portable air conditioner that provides cooling, dehumidification, and fan-only functions. It is suitable for both home and office use.

Capabilities:

Cooling: Cools the air in a room to a temperature between 16°C and 30°C.
Dehumidification: Removes excess moisture from the air, creating a more comfortable environment.
Fan-only: Circulates the air in a room without cooling or dehumidifying it.

Features:

Two fan speeds: Choose between high and low fan speeds to adjust the airflow.
24-hour programmable timer: Set the unit to turn on or off at specific times.

Welcome

Thank you for purchasing the new Portable Air Condition SY-AC700. Read this

instruction booklet carefully in order to benefit fully from this product. Store the user

manual in a safe place for future reference.

Important Safeguards

Please read the Manual carefully before operating the machine

ELECTRICAL CONNECTIONS:

Before plugging the appliance into the socket, check that:

. The voltage corresponds to the value indicated on the rating plate

that is located on the back of the appliance.

. The power socket and the electrical circuit are suitable for the

device.

. The socket matches the plug. If not, have the plug replaced.

. The power outlet is properly grounded. Failure to comply with these

instructions

exempts the manufacturer from all liability.

• The appliance is for indoor use only.

• Place the air conditioner on a fat surface and keep it placed vertically to ensure the

normal operation of its compressor.

• This appliance is for domestic use only and not for commercial use.

• Before inserting the mains plug into the socket, check that the mains supply voltage

and current rating corresponds with the power supply details shown on the rear

specification plate of the unit.

• Read all instructions, Rated Power Supply: Please connect the unit with Grounded

Power source: 220-240VAC, 50HZ.

• Disconnect the power plug before dismantling, assembling or before cleaning.

• Avoid touching mobile parts of the appliance.

• Never insert fingers, pencils or any other objects though the guard whenever the

power plug is connected, especially while running.

• Persons (including children) with reduced physical, sensory or mental capabilities

or lack of experience and knowledge do not intend this appliance for use, unless

a person responsible for their safety has given them supervision or instruction

concerning use of the appliance

• The appliance is not intended for use by young children or infirm persons unless

they have been adequately supervised by a responsible person to ensure that

they can use the unit safely.

• Young children should be supervised to ensure that they do not play with the

appliance.

• Do not use the appliance for any other purposes than its intended use.

• The appliance must not be used if the guards are not fasten according to the

instructions.

• When the power cord is damaged, it must be replaced by the manufacturer or its

service agent or a similar qualified person in order to avoid hazard

• Do not use your appliance with an extension cord unless it has been checked

and tested by a qualified electrician or electrical supplier

• In the case of any malfunction, return to an authorized service agent. Never open the

unit and try to repair it by yourself.

• The air conditioner unit must always be stored and transported upright,

otherwise you may cause irreparable damage to the compressor; in case of

doubt we suggest to wait for at least 24 hours before you start air-

conditioning unit.

• Avoid restarting the air conditioning unit unless 3 minutes have passed since

being turned off, or the compressor may be damaged.

• Never use the mains plug as a switch to start and turn off the air conditioning

unit. Use the provided ON/OFF switch located on the control panel.

• Do not place the Portable Air conditioner next to heat sources or direct sunlight.

• Always place the portable air conditioner on a dry stable place.

• Always use the original supplied accessories. Any third party accessory might

damage the appliance.

• The ideal environmental temperature for the portable air conditioner should be 15-

35ºC.

• The appliance shall not be installed in the laundry.

• The appliance must be positioned so that the plug is accessible and it shall be

installed in accordance with national wiring regulations.

Special warning

•

Place the A/C on even ground and install it vertically so as to ensure normal

operation of the compressor.

•

The A/C should be at least 50cm away from surrounding objects. Keep air inlet

and outlet smooth.

•

Do not operate the A/C near gasoline or any other inflammable liquid.

•

Do not use spraying agent and other solvent or flammable substances near the

A/C; otherwise, its plastic may deform and electric parts may be damaged.

Energy Saving Tips

• Do not cover or restrict the airflow from the Outlet or Inlet grills.

• The minimum distance from furniture and wall should be 50CM.

• Keep the filters clean. Under normal conditions, the filters should be cleaned

approximately every 30 days. Since the filters remove airborne particles, more

frequent cleaning maybe necessary, depending on the indoor air quality.

• Set the fan speed switch to high cool and the thermostat to the coolest position for

the initial start-up, then set the fan switch to Low cool and lower the thermostat to a

comfortable setting.

Suggestions

• If you want to get better effect, we suggest you not to use cooling function when

ambient environment is higher than 35 ºC.

Basic functions

• This unit offers cooling, dehumidifier and fan mode, ideal for home and office

use.

• The unit include 2 fan-speed level accessible by the panel control or the remote

control.

• This unit is designed with various protection functions such as 24 hours

programmable timer, auto condensation, intelligent temperature sensor and

water control with warning.

• The ideal temperature for using the portable air conditions is from 15ºC~35ºC.

Parts of the SY-AC700

1: Control Panel

2: Wind guide bar

3: Air Inlet (R)

4: Wheels

5: Handle

6: Air outlet

7: Air inlet (L)

8: Dehumidification drainage nozzle

9: Filter handle

10: Exhaust duct assembly

11: Window sealing plate assembly

12: Remote control

Control and Settings

Power key

Press this button to turn On/Off the air conditioner.

Mode Key

Press this button to select cool (cooling), fan only (wind) and

dry (dehumidification) mode

Temperature / time up and down adjusting keys

Press this button in cooling mode to increase/decrease the

temperature.

Press the buttons in timing mode to adjust On/off time;

Press Up and Down keys simultaneously to switch between

Fahrenheit and Celsius temperature.

Wind Speed key

Press this button to select High or low wind speed

Timer key

In Standby mode, press this button to set the ON time.

In start-up mode, press this button to set the OFF time.

Temperature / time display window

The LCD display indicates the adjusted temperature and time.

Remote controller receiving window

Remote sensor to receive signal from the remote controller.

ºC-ºF switching key

Press this button to switch between ºC and ºF

Sleep Key

Press this button under cooling mode or press the “Timing” button and “Down” button

simultaneously to activate the Sleep mode.

The fan will start to blow at low speed (Low indicator light turn on)

At this time the temperature will keep on increasing 1ºC every 2 hours

and will remain constant after two increases. (The fan speed cannot be adjusted).

Placement and installation

Placement

•

Place the portable AC on a flat floor near a window.

•

Pl ace the machine in a dry place and keep it at least 50cm away from any

surrounding objects.

Installation

•

Screw the exhaust duct assembly (exhaust joint end) into the rear panel exhaust port

(anticlockwise).

• Insert the air exhaust hose into the window sealing plate, adjust the opening width

of the window so that the window can match with the sealing plate properly; the

length of the sealing plate is adjustable.

Incorrect installation

•

It is important to keep the exhaust duct clean and smooth. Incorrect installation will

affect the functioning of the A/C.

•

Prevent bending the exhaust pipe.

•

Ensure air can flow smoothly in the duct.

Warning:

The exhaust duct is designed especially for this model.

Do not replace or stretch it or it will result in failure.

Notice:

The maximum developed length of the exhaust duct is 1,500mm. Shorten its length as far as

possible while in use. Keep it horizontal while installation.

Operation method

Cooling mode

•

When the A/C enters into the cooling mode automatically or the cooling mode is

selected after the power is turned ON, the cooling indicator lamp lights up.

•

Press the Up/Down key to adjust the temperature (16 ºC ~30

ºC).

•

Press the Speed key to select between High and Low speed.

Fan mode

•

Press the mode button on the control panel or the remote control to choose the

Fan mode, the wind indicator lamp will turn on.

•

Press the Speed button to select between High and Low speed.

•

The temperature cannot be set under fan mode.

Dehumidification mode

•

Press the mode button on the control panel or the remote control to select the

dehumidification mode. The dehumidification indicator light will turn on.

•

When entering dehumidification mode, if the room temperature ≥17 ºC (62 ºF), the

Compressor will start to work. When the room temperature ≤15 ºC (59 ºF), the

Compressor stops.

When the temperature raises back to ≥17 ºC, the compressor restarts again. (in order to protect

the compressor, it will be restarted 3min. later).

•

In dehumidification mode, the speed of the fan is by default at Low speed and the

wind speeds is not adjustable.

Timer mode

•

In standby mode, press the Timer button to set ON time. Press the Up and Down

buttons to set the starting time (1~24H), the timer indicator lamp lights on.

•

In startup mode, press the timer button to set OFF time. Press the Up and Down

buttons to set the switch off time (1~24H), the timer indicator lamp lights on.

Sleep mode

•

When in cooling mode, press the remote controls "sleep" key (or press the "timing"

+ "down" buttons simultaneously) to put the unit into sleep mode. The fan will begin

to blow on low speed and the low wind indicator will light up. In this case, the wind

speed cannot be adjusted. Press the buttons once more to exit the current mode.

Important Note:

Never turn off the air conditioner by unplugging it from the power supply. Always press the

"ON / OFF" button and wait a few minutes before unplugging it. This allows the device to

perform a check cycle to verify operation.

Water Drainage

The product has an automatic water evaporation system. The circulation of condensed water cools

down the condenser. This not only increases refrigeration efficiency but also saves energy.

•

If the internal vessel is full of water, the display screen will

display “FL”, and the compressor stops working automatically.

1. Turn the unit off and unplug the power cord.

2. Remove the exhaust duct assembly.

3. Move the unit to an appropriate place.

4. Unscrew the water drainage cover and unplug the water

blocker. Use a water container to remove the water from

under the unit.

5. Plug in the water drainage cover well.

6. Reinstall the exhaust duct assembly and start the machine.

Maintenance

Note: in order to avoid electric shock, please turn off the A/C and unplug before

maintenance or repair.

Cleaning the surface

Clean the housing with a duster or a soft wet cloth. Do not use any chemical solvent (such as

benzene, alcohol, gasoline). The surface may be damaged or may even deform the complete outer

casing.

Air filter cleaning

Clean the air filters every 2 weeks. If the air filter is blocked with dust, the efficiency will reduce.

Pull the filter out towards you and then pull it up as shown below.

Wash the air filters by immersing it gently into warm water (about 40 ºC) with a neutral detergent,

rinse it and dry it thoroughly in a dry place.

Install the air filters carefully after cleaning the filters. Make sure they are well fit before using the

unit again.

If the filter is not too dirty, If the filter is very dirty,

use a vacuum cleaner clean it with warm water

to suck the dust. The ideal temperature of the water is 40ºC

Note:

1. Do not use high temperature water when cleaning the filter. (Optimum temperature is 40ºC) or

harsh detergents such as alcohol, petrol, benzene, etc..

2. In order to avoid filter screen deformation, keep the filter away from direct heat and place it in a dry

area.

3. Do not operate the machine without its filter. This can cause damage to the unit.

After Season Maintenance

Pull out the plug in a drainage hole and empty the water-receiving plate, or drain out the water by

leaning the unit. Then enter into the fan mode, and press the button for 5 seconds until it sets to

the low fan speed. Keep this mode on for half a day until its inside becomes dry.

Turn off the unit and pull out the plug.

Clean its filter screen and reinstall back.

Tie the wire and bind it together, then put it into the accessories storage space.

Remove the exhaust pipe and accessories and keep them safely.

Put the unit into a plastic bag, and then keep it in a cool and dry place.

Take out the batteries of remote control and safely keep them.

* All accessories can be placed in the accessories storage on the back of the unit.

Using the unit after a long time

1. Check whether the water plug and filter screen are installed.

2. Check whether the power cord is intact. If it has any signs of breakage, do not use the A/C

3. Reinstall the remote control batteries.

4. Reinstall other parts following the installation instructions.

Error detection

Error-detecting code Multi-functional defection

E1 Coil temperature sensor failure

E2 Indoor temperature sensor failure

Anti

freez

protection

. When the coil

temperature is below 0ºC, the

whole machine will stop. When the coil temperatures raises to 8ºC or

more, the protection will disconnect and the unit will restore to its

original working state.

TROUBLESHOOTING

TROUBLE CAUSE SOLUTION

The A/C doesn’t

work

Not plug in Plug in

The display panel displays

“FL”

Restart the A/C after power off and

drainage process. The unit should work

fine.

Time OFF timer function is

activated

Restart the unit after turning it off for 3

minutes.

The refrigeration

effect of the

conditioner is

not good.

Direct sunlight Draw the curtain

Doors or windows are open.

Room is too crowded or heat

source placed in the room

Close the doors and windows and

remove the heat source

Dirty filter screen Clean or replace the filter screen

Air inlet or air outlet is blocked Remove the blockage

The air conditioner

makes too much

noise

The A/C is not placed on a flat

level

Place it on a flat and solid surface and

try avoid shaking.

The compressor

Does not work

The compressor delay protection

has been activated

Wait for 3 minutes and restart the

machine when its temperature is

reduced

Important information for the correct disposal of the product in accordance with

Directive 2002/96 / EC.

At the end of its useful life, the product should not be disposed off with household

waste. It must be taken to a special selective collection center of the municipal

agencies or to a distributor who presents this service. The correct elimination of an

electrical appliance avoids possible negative consequences for the environment

and health derived from an inadequate elimination and allows to recover its

materials to obtain significant savings in energy and resources. As a reminder of the

need to dispose of the appliances selectively, the product is marked with a trash

can with wheels crossed with an X.

DECLARATION OF CONFORMITY

Manufacturer Name: Satyatrade S. L.

Address: Pol. Ind. La Raya. C/ Guadalquivir, 2.

Camarma de Esteruelas, 28816 Madrid

Tel: 902 430 967

Fax: 91 8864285

NIF: B83254763

Manufacturing country: China

Description: Portable Air Condition

Sytech® SY-AC700 complies with the following directives:

EMC Standard: Directive 2014/30/EU

LVD Standard: Directive 2014/35/EU

EER Standard: Directive 2009/125/EC

ROHS Standard: Directive 2011/65/EU Restriction of Hazardous Substances

Signed: Ajeet Nebhwani Utamchandani

Sole Administrator

Sytech SYAC700 Owner's manual

Brand: Sytech

Model: SYAC700

Category: Mobile air conditioners

Type: Owner's manual

Sytech SYAC700 is a portable air conditioner that provides cooling, dehumidification, and fan-only functions. It is suitable for both home and office use.

Capabilities:

Cooling: Cools the air in a room to a temperature between 16°C and 30°C.
Dehumidification: Removes excess moisture from the air, creating a more comfortable environment.
Fan-only: Circulates the air in a room without cooling or dehumidifying it.

Features:

Two fan speeds: Choose between high and low fan speeds to adjust the airflow.
24-hour programmable timer: Set the unit to turn on or off at specific times.

Download PDF

report

Sytech SYAC700 Owner's manual

Sytech SYAC700 Owner's manual

Related papers

Other documents