Sytech SYXTR29BT Owner's manual

Brand: Sytech

Model: SYXTR29BT

Category: Portable speakers

Type: Owner's manual

Welcome

Thank you for purchasing the new Wireless Party speaker SY-XTR29BT. Please read this manual carefully before

operating your product. And pay close attention to the precautions which are mentioned below. Store this user manual in

a safe place for future reference.

Safety Precautions

Points to observe for safe usage

Read this manual carefully before using the product. They contain instructions on how

to use this product in a safe and effective manner. SYTECH will not be responsible

for problems resulting from failure to observe the instructions in this manual.

Turn off the device immediately in case of a problem.

Failure may cause personal injury or damage to the product.

Return it to your authorized SYTECH dealer for repairing.

Product cleaning.

Use a soft dry cloth for periodic cleaning of the product. For more severe stains, please

dampen the cloth with water only. Any other product such as alcohol, benzene, may damage the paint or

the plastic.

Temperature

Make sure before using the product, the room temperature is between +35ºC (+95ºF) and -10ºC (+14ºF)

Maintenance.

If you have problems, do not attempt to repair the unit yourself.

Surface

Place the unit on a flat surface.

Leave enough space around the unit for a proper ventilation.

Heat.

Do not place the product near any heat sources or to direct sunlight.

Accessories.

Use only supplied accessories

Charging the speaker

• Connect the AC adaptor provided with your speaker. (DO NOT USE ANY OTHER AC ADAPTOR OTHER THAN THE

ONE PRVIDED).

• Plug in the AC adaptor jack into the DC 5V input connector located on the top panel of the speaker.

• The Charge LED light will turn to red indicating the battery is being charged.

• Once the battery is fully charged, the LED light will turn off.

• Disconnect the AC adaptor and use your speaker with the batteries.

Remote Control Functions

1. Power

2. Mode. Input selection (AUX-USB-TF-FM-BT)

3. Mute

4. Play / Pause. FM Auto scan

5. Next track, Next FM preset

6. Previous track, Previous FM preset

7. Equalizer effect

8. Decrease volume

9. Increase volume

10. Numerical keys

11. Repeat function

12. USB-Micro-SD function

“

This picture is for reference purposes only”

1. Under normal circumstances, the remote control should be aimed directly at the infrared receiver window of the

unit.

The maximum distance for the remote-control operation is approximately 6 meters and within a 30° angle.

2. When operating the remote control, aim the remote control at the infrared receiver window of the unit and

ensure that there are no obstacles between the remote control and the unit.

3. If the remote receiver is facing direct sunlight, it may fail. In this case, move the speaker away to avoid the light.

4. Avoid mixing old and new batteries. Replace the remote-control batteries regularly.

Wired microphone usage

• Connect the supplied wired microphone to the MIC input jack located on the top panel of the speaker.

• Control the Volume of the MIC by rotating the Mic knob.

• Control the echo effect by rotating the Echo knob.

Functions and connections

1. Microphone Eco effect controller

2. Microphone volume controller

3. Power On/Off

4. RGB Light switch

5. Microphone input

6. LED charging light (Charging: Red / Completed: Off)

7. Volume controller

8. USB port

9. Micro-SD slot

10. Previous track – Previous FM pre-set – Vol-

11. Play/Pause – FM Auto scan – TWS

12. Next track – Next FM pre-set - Vol+

13. Mode selector : AUX-USB-Micro-SD-FM-BT

14. Aux input

15. DC 5V. input

USB & Micro-SD Slot

USB FUNCTION:

• Make sure your USB flash is formatted as FAT32.

• Insert the USB flash into the USB port of the speaker system

• The unit should detect the USB automatically and play the first track

• If in the case the USB does not start automatic playback, press the Input button and select MP3 mode.

• If you wish to pause the music, simply press the pause button

• To select the next track, simply press the “Next” button

• To select the previous track, simply press the “Previous” button

Note:

1. Make sure the music files are MP3, WAV format or else the music system will not be able to read the files.

2. Make sure the music files are recorded to the root directory.

3. It is advisable to remove unnecessary files for faster reading of the content.

MICRO-SD CARD FUNCTION:

• Make sure your Micro-SD card is formatted as FAT32.

• Insert the Micro-SD card into the TF slot of the speaker system

• The unit should detect the Micro-SD card automatically and play the first track

• If in the case the Micro-SD card does not start automatic playback, press the Input button and select MP3 mode.

• If you wish to pause the music, simply press the pause button

• To select the next track, simply press the “Next” button

• To select the previous track, simply press the “Previous” button

Bluetooth function

• Select the BLUETOOTH mode by pressing the “MODE” switch on the top panel of the unit or from the remote control

itself.

• Please ensure the Bluetooth device you wish to connect has the Bluetooth function enabled and visible.

• Start the scan function from your device and search for “SY-XTR29BT”.

• Once you have found the device, press on it and connect the speaker with the device.

• When the connection is successful, a “tick” tone will be heard. If the speaker cannot be connected, please restart the

speaker or the device and try again.

• After the connection is successfully established, you can begin to play music. To ensure continuous stability of the

music signal, try to keep the Bluetooth device and the mobile phone facing one another.

• The distance for the Bluetooth signal range is up to 14 meters when no obstacles in between.

FM Radio function

• Press the “MODE” button to switch to FM mode.

• Press the “Pause/Play” button to start the automatic search of the stations.

• The unit will start to search all the main stations and will store them automatically.

• Once the scan search has finalized, press the “NEXT” or “PREVIOUS” buttons to access to the stored channels.

• The unit will store up to 40 presets.

Note: The FM stations can only be stored automatically. The position of the channel store number will start from the

lowest FM frequency to the highest. The pre-set memories cannot be memorized manually.

TWS Function

The TWS function allows you to connect two speakers at the same time and lets you enjoy “True Wireless

Stereo” music.

• Select the Bluetooth mode on the two speakers.

• Long press the “Play/Pause/TWS” button during 3 or 4 seconds on the two speakers.

• A beep sound will be heard confirming the pairing of the two speakers.

• Connect your mobile device via Bluetooth the speaker

• Play the track from your mobile device and enjoy True Wireless Stereo experience as each speaker will act as left

and right.

• To exit the TWS mode, simply long press the “Play-Pause – TWS” button.

Main technical specifications

Basic Specifications

• 1 x 8” Woofer

• USB/Micro-SD/FM/Bluetooth function

• 1 x Microphone input

• 1 x Aux input

• LED display

• Remote control

• RGB light on woofer grill

• Output power: 10W RMS.

• Output power: 75W PMPO

• TWS Function (True Wireless Stereo)

• Built in rechargeable battery. 1800mAh 3.7V

Bluetooth Specifications

• Bluetooth Version: V5.0 + EDR

• Bluetooth Support: 5.0

• Bluetooth Profiles: A2DP, AVRCP

• Bluetooth pairing name: SY-XTR29BT

USB/Micro-SD card Specifications

• 2.0 USB Port (Max Capacity: 32GB)

• SD Card Slot (Max Capacity: 32GB)

• Compatible Audio Formats in USB: MP3 / WAV

• Compatible Audio Formats in SD: MP3 / WAV

Technical Specifications

• Output power: 75W PMPO

• Output power: 10W RMS

• SNR: 90dB±3dB

• Frequency response: 100-18KHz

• Power supply: DC 5V.-1A / AC110V-240V, 50/60Hz

• Working time: 2-3 hours (Depends on Volume level)

• Charging time: 3 to 4 hours

• Above specifications are of “SY-XTR29BT are for reference purpose only.

• Due to continuous product development, specifications may be subject to change without prior notification.

• Do not expose to adverse weather conditions (Such as rain or high temperatures) as it can cause malfunctions

Simple troubleshooting

Try the troubleshooting steps below if you are having problems while using your speaker. If problems still exist, please

look for a qualified technician or contact Sytech technical department.

To prevent electric shock or damage the speaker, do not repair by yourself.

Symptom Possible problem Solution

No function light & no

sound

1. Plug is not well connected

Insert the plug into electrical outlet

2. Speaker power button is

not turned on

Turn on the button

Function light on but no

sound

1. Cable misconnected Turn off the power, check the input jack to ensure

proper audio signal is connected to relevant input jack

2.Speaker are not

connected or misconnected

Power off, then check and confirm the cable

connection again

3.Audio signal is not

transmitted to speaker

Check the speaker if there is audio signal output

Remote control does not

work

1. Before you press any function button, first select the correct source with the

remote control instead of the main unit

2. Reduce the distance between the remote control and the unit

3. Insert the battery with its polarities (+/- signs) aligned as indicated

4. Replace the battery

5. Aim the remote control directly at the sensor on the front of the unit

Cannot display some files

in the USB device

1. The number of folders or files in the USB device exceeds the max limit. This is not

a malfunction of the unit.

2. The formats of these files are not supported

USB device not supported 1. The USB device is incompatible with the unit. Try another one.

Poor radio reception 1. Increase the distance between the unit and your TV or VCR

2. Connect an audio cable into the AUX input

Bluetooth does not connect

with external device

1. Verify that the external device is compatible with A2DP

2. Verify that the external device is within the transmission range

3. Verify that the external device has already been paired with the unit.

4. Verify if there is no other external device paired with the unit.

If the problem exists after checking related procedures above, please refer to the appointed a service agent to fix

the problem. Do not attempt to open the cover, otherwise the warranty will be void.

Declaration of Conformity

Manufacturer Name: Satyatrade S. L.

Address: Pol.Ind.La Raya. C/ Guadalquivir, 2.

Camarma de Esteruelas, 28816 Madrid

Tel: 902 430 967

Fax: 91 8864285

NIF: B83254763

Manufacturing country: China

Description: Acoustic Speaker System

Sytech® SY-XTR29BT complies with the following directives:

RED Standard: Directive 2014/53/EU

ROHS Standard: Directive 2011/65/EU Restriction of Hazardous Substances

Signed: Ajeet Nebhwani Utamchandani

Sole Administrator

www.sytech.es

Sytech SYXTR29BT Owner's manual

Brand: Sytech

Model: SYXTR29BT

Category: Portable speakers

Type: Owner's manual

Download PDF

report

Sytech SYXTR29BT Owner's manual

Sytech SYXTR29BT Owner's manual

Related papers

Other documents