2. PAC
  3. MAZK849
MAZK849

PAC MAZK849, BKMAZK849 User manual

  • Hello! I am an AI chatbot trained to assist you with the PAC MAZK849 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What components can I find inside the product?
    How to assemble the product?
    How to use ISO mount with this product?
    How to use the product for Double DIN Mount Applications?
CUSTOMER HELP LINE
USA 800-323-4329 • Canada 800-245-8777
iMAZK849
Automotive Products Division
1040 Avenida Acaso • Camarillo, CA 93012, U.S.A.
USA Sales (800) 336-6500
Canada Sales (888) 922-3006 • USA Fax (805) 388-7950
For information about other American International automotive
accessories visit our website at:
http://www.americaninternational.net
Mazda
2010-13 MAZDA 3
VEHICLE APPLICATIONS
MAZK849 Mounting Kit
©2014 AMERICAN INTERNATIONAL INDUSTRIES, INC.
TECH Ver. 6/14 PRINT Ver. 6/14
2 7
KIT ASSEMBLY INSTRUCTIONS
Single DIN Mount Applications
1. Attach the left and right side brackets to the main bracket.
2. Insert pocket (part # UNI-POC) into lower section of the main frame.
3. Attach left and right side brackets to the rear of the pocket using screws supplied.
4. Insert DIN sleeve from your new radio into the upper section of the installation kit.
5. Depress the tabs from inside the sleeves opening upward, outward, and downward to
secure sleeve to the installation kit.
6. Install radio into sleeve and lock into place.
7. SUGGESTED...Attach a rear support bracket to the rear of the new radio and adjust
as necessary to attach to the rear support stud locate on the back of the pocket using
the small phillips screw supplied with kit.
8. Attach the metal panel fastener clips (included with kit) (4) to each mounting tab on
the back side of the main panel.
Note: ISO trim ring (UNI-T1) may be used in place of after-market radioʼs
removable trim ring.
2010-2013 Mazda 3
ISO Mount
Brackets
Fig. B
UNIPOC
Main Frame
DIN
Sleeve
DASH DISASSEMBLY INSTRUCTIONS
1. Carefully unsnap the hazard button/ac vents panel by gently popping the factory
panel out (you can use a soft tool), and remove.
2. Now you can remove the two screws holding the OEM radio. Disconnect the
wire harness and antenna lead and remove the radio.
NOTES
6 3
Single ISO Mount Applications
1. Attach the left and right side brackets to the main bracket.
2. Insert pocket (part # UNI-POC) into lower section of the main frame.
3. Attach left and right side brackets to the rear of the pocket using screws supplied.
4. Attach (1) ISO Spacer to the inside of upper section on both Left & Right
mounting brackets
5. Insert ISO mountable radio between ISO mount brackets.Then loosely attach to sides
of radio using screws provided with radio or hardware included with kit.
6. Slide radio component forward or backward for desired look and tighten screws.
7. SUGGESTED...Attach a rear support bracket to the rear of the new radio and adjust
as necessary to attach to the rear support stud locate on the back of the pocket using
the small phillips screw supplied with kit.
8. Attach the metal panel fastener clips (included with kit) (4) to each mounting tab on
the back side of the main panel.
Note: ISO trim ring (UNI-T1) may be used in place of after-market radioʼs
removable trim ring.
Fig. C
For ISO mount only:
Attach (1) ISO Spacer to the
inside of upper sections of the Left & Right
mounting brackets as shown in Fig. A.
Fig. A
ISO Mount
Brackets
UNIPOC
UNIT1
(Top)
Mai
n Fra
me
NOTES
NOTES
Fig. D
REMOVE ALL SHADED
MOUNTING TABS ON BOTH
LEFT AND RIGHT BRACKETS
ISO Mount
Brackets
Main Frame
Cut
Cut
UNI
T2
Double DIN Mount Applications
Note: REMOVE POCKET SUPPORT TABS (Both L&R mounting brackets).
1. Attach the left and right side brackets to the main frame.
2. Cut and remove the center rib from the main frame and file edges smooth.
3. Follow steps 4-6 from single ISO instructions
4. SUGGESTED... Attach a rear support bracket to the rear of the radio components
and adjust as needed to allow rear support bracket to rest in the sub-dash.
5. Attach the metal panel fastener clips (included with kit) (4) to each mounting tab
on the back side of the main panel.
Note: DBL ISO trim ring (UNIT2) may be used in place of after-market radioʼs
removable trim ring.
4 5
For ISO mount only:
Attach (1) ISO Spacer to the
inside of upper sections of the Left & Right
mounting brackets as shown in Fig. A.
Fig. A
/