Black & Decker HGS200 Series User manual

Page is loading ...

3

IMPORTANT SAFETY INSTRUCTIONS

When using your steamer, basic safety precautions should

always be followed, including the following:

SAVE THESE INSTRUCTIONS.

This product is for household use only.

POLARIZED PLUG (120V models only)

To reduce the risk of electric shock, this

appliance has a polarized plug (one blade

is wider than the other). This plug will ﬁt in

a polarized outlet only one way. If the plug

does not ﬁt fully into the outlet, reverse the

plug. If it still does not ﬁt, contact a qualiﬁed

electrician to install the proper outlet. Do not

attempt to modify the plug in any way.

TAMPER-RESISTANT SCREW

Warning: This appliance is equipped with a

tamper-resistant screw to prevent removal

of the outer cover. To reduce the risk of ﬁre

or electrical shock, do not attempt to remove

the outer cover. There are no user-serviceable

parts inside. Repair should be done only by

authorized service personnel.

Note: If the power supply cord is damaged, in

order to avoid a hazard, it should be replaced

by qualiﬁed personnel.

• READ ALL INSTRUCTIONS BEFORE USING.

• To reduce the risk of contact with hot water emitting from

steam vents, check appliance before each use by holding it

away from body and operating steam button.

• Only use steamer for intended use.

• To reduce the risk of electric shock, do not immerse the

steamer in water or other liquids.

• Always turn the steamer off by pressing and holding the

power button for 3 seconds, until the blue indicator light

turns off, before unplugging from the outlet. Never pull on

the cord to disconnect from the electrical outlet; instead

grasp plug and pull to disconnect. Always keep unplugged

when not in use or filling the tank.

• Do not allow cord to touch hot surfaces. Let steamer

cool completely before putting away. Loop cord loosely

together and secure with provided Velcro strap when

storing.

• Always turn off the steamer by pressing and holding

the power button for 3 seconds, and then unplug from

the electric outlet before filling with water, emptying, or

cleaning, and when not in use.

• Do not operate the steamer with a damaged cord, or if the

appliance has been dropped or damaged, or if it is leaking.

To reduce the risk of electric shock, do not disassemble or

attempt to repair the steamer; take it to a qualified service

person for examination and repair, or call the appropriate

toll-free number in this manual. Incorrect reassembly or

repair can cause a risk of fire, electric shock, or injury to

persons when the steamer is used.

• Close supervision is necessary for any appliance being

used by or near children. Do not leave the steamer

unattended while connected.

• Burns can occur from touching hot metal parts, hot water,

or steam. Use care when you turn a steam appliance upside

down – there may be hot water in the reservoir. Avoid rapid

movement of steamer to minimize hot water spillage.

• To reduce the likelihood of circuit overload, do not operate

another high wattage appliance on the same circuit.

• If an extension cord is absolutely necessary, a minimum

13-ampere cord should be used. Cords rated for less

amperage can result in a risk of fire or electrical shock due

to overheating. Care should be taken to arrange the cord

so that it cannot be pulled or tripped over.

• Do not use outdoors.

• Do not use anything other than water in the steamer while

in use or during cleaning.

• Never steam clothing while on a body.

• Never aim the steam directly towards people, animals

or plants. The steam is very hot and can results in burns.

Burns can occur from touching hot parts (including the

steamer head and frames), hot water, or steam.

• Never hold the steam head down while at rest or tilt it in a

backward position as this may result in hot water discharge

and possibly injury.

• This appliance is not intended for use by persons (including

children) with reduced physical, sensory, or mental

capabilities, or lack of experience and knowledge, unless they

have been given supervision or instruction concerning use of

the appliances by a person responsible for their safety.

• To avoid burns, when putting on or taking off attachments,

be sure the unit is off and no steam is being emitted.

• Children should be supervised to ensure that they do not

play with the appliance.

• The steamer must be used and rested on a stable surface.

4

GETTING TO KNOW YOUR STEAMER

1. Steam trigger

2. Continuous steam switch

3. Comfort grip handle

4. Removable water tank

(Part # HGS200-01)

5. Power button (not shown)

6. Lint frame* (Part # HGS200-02)

7. Delicate fabric frame

(Part # HGS200-03)

8. Upholstery frame

(Part # HGS200-04)

Product may vary slightly from what is illustrated.

*Lint frame included in select models only.

2

3

1

4

6

7

8

5

HOW TO USE

This product is for household use only.

GETTING STARTED

• Remove all labels, tags and stickers attached to the body, or cord of the

steamer and the plastic band around the power plug.

• Remove and save literature.

• Read all the instructions before using your steamer.

IMPORTANT NOTES

• Using distilled, puriﬁed, or ﬁltered water is highly recommended to maintain

optimal performance. Tap water contains minerals that build up over time.

• Any water droplets visible inside the tank are from individual quality

control tests done to ensure every steamer meets our high standards for

product performance.

• Do not use perfumes, oils, or other additives.

• Always review the garment manufacturer’s care label instructions before

steaming, and always test fabrics for colorfastness in inconspicuous

areas (such as an inseam). Steamers are not recommended for use on

leather, suede, vinyl, plastic, or other steam sensitive fabrics.

• During use the steamer and accessories will become hot. Avoid

attaching or removing frames while still hot.

• After preheating, prime water pump by holding the steam trigger until

steam forms.

• It is normal to feel or hear the water pump in the handle.

• The water pump may become louder when the water level in the tank is

low. Check and reﬁll tank, as needed.

ATTACHING FRAMES

The steamer comes with three optional-use attachment

frames recommended for use with a variety of fabrics and

upholstery.

1. Select the proper frame using the following chart.

2. While the frame and steamer are cool, gently attach

the top of the frame over the top the steamer head and

then click the bottom of the frame into place. (A)

Note: Frame tab points down when in correct position.

3. Allow steamer to cool prior to removing frame. Gently

pull on the tab. (B)

Note: Be careful when removing frames as condensation

may build up during use.

A

B

6

Frame Usage

Lint Frame

Garment Care Label: For any garments that call

for medium to high heat and allow for use of

steam.

Tip: Frame helps remove lint, hair, and animal fur.

Delicate Fabric Frame

Garment Care Label: For any garments that call

for low heat and allow for use of steam.

Tip: For items with embellishment, turn the gar-

ment inside out to better remove wrinkles and

avoid damage to sensitive areas.

Upholstery Frame

Upholstered Fabrics: Great for deodorizing and

refreshing bedding, mattresses, curtains, plush

toys, furniture, and hard surfaces (such as count-

ers or desks that are not heat sensitive).

Tip: Always test for colorfastness and heat sensi-

tivity on an inconspicuous area.

FILLING THE WATER TANK

1. Place the steamer on its base on a stable surface.

2. Hold the handle to stabilize and pull out the removable

water tank with the other hand. (C)

3. Gently pull out the rubber water tank cover at the top

of the tank. (D)

Tip: Using distilled, puriﬁed, or ﬁltered water is highly

recommended and will reduce mineral buildup. Do not use

oils, perfumes, or scented additives.

4. Using a clean measuring cup, pour water into opening

until water reaches the “MAX” level mark on the top

of the tank. (E) Do not overﬁll. Close the rubber cover

securely.

5. Dry off any excess water from the tank. Push water

tank back into the steamer base; click into place.

6. To reﬁll at any time during use, turn steamer off by

pressing the power button until the blue indicator

light is off, unplug from outlet, and follow the above

procedure.

Tip: After reﬁlling, allow to reheat for 45 seconds and then prime pump by

holding steam trigger until steam forms.

C

D

E

7

USING THE HANDHELD STEAMER

1. Read the manufacturer's fabric label to make sure the fabrics are

suitable for steaming.

• If you see “do not iron” or this icon

, attach the delicate fabric

frame and make sure to test on an inconspicuous area prior to

steaming the entire garment.

• If you see “do not steam” or this icon

, do not steam the garment.

2. Refer to the “Attaching Frames” section for determining whether to use a

frame. Attach or remove frames while the steamer and frames are cool.

• Hang the garment in an area that will not be impacted by the heat

and steam, such as on a shower rod.

3. Plug the steamer into an outlet and then press the power

button. (F) The blue power button light will slowly blink,

indicating that the steamer is heating.

4. After about 45 seconds the power light will stay on,

indicating the steamer is preheated.

5. Prime the water pump by holding steam trigger until

steam forms.

6. To generate steam, press down on the steam trigger

with your index ﬁnger. (G) As long as the trigger is

held down, steam will emit from the steamer. When the

trigger is released, the steam will stop.

• To generate a constant ﬂow of steam without holding

the trigger, press the steam trigger and then slide the

continuous steam switch down. (H) This will activate

the continuous steam feature. To turn the steam off,

press the trigger, push the continuous steam switch

up and then release trigger.

7. With your free hand keep the fabric taut. Steam the

garment with slow, downward strokes, keeping the head

of the steamer in contact with the fabric. (I)

Note: It is normal to feel or hear the water pump in the handle.

Note: If the steamer is left inactive, the auto shut-off

feature will activate, indicated by the rapidly blinking

Power Button. To resume steaming after the auto shut-off

is activated, either press the steam trigger or press the

power button. Allow the steamer to preheat if needed.

F

G

H

I

8

8. When ﬁnished steaming, press and hold the power button

until its blue light turns off (about 3 seconds) and unplug

from outlet. (J)

9. Stand steamer on its base and allow it to completely

cool off before storing. (K) To avoid mineral buildup,

empty the tank after each use.

Auto Shut-Off

The steamer will automatically switch to auto shut-off

mode after being left inactive for 15 minutes. The boiler and

water pump will turn off until reactivated. Rapid blinking of

the power button light indicates that the steamer is going

into auto shut-off mode. To resume steaming, press the

steam trigger or power button and wait for steamer to fully reheat.

Steam Cleaning Around the Home

Using steam to clean household items that can tolerate hot, damp steam

without damage is non-toxic, and inexpensive. This natural cleaning method

is beneﬁcial to those sensitive to chemical cleaners or trying to reduce

chemicals in the home. Steam upholstery, draperies, linens and home textiles

to clean and refresh.

CLEANING AND CARE

This product contains no user serviceable parts. Refer to qualiﬁed service

personnel.

CLEANING STEAMER EXTERIOR

1. Make sure steamer is off, unplugged and completely cool.

2. Wipe the ironing plate and outer surface with soft, damp cloth. Water

and small amounts of gentle household soaps, such as dishwashing

liquid, can be used on the exterior. Never use heavy-duty cleaner, or

abrasive scouring pads that may scratch or discolor the steamer.

3. After the steamer has been thoroughly dried, turn it back on and lightly

steam over an old cloth. This will help remove any reside left in the

steam holes.

4. When ﬁnished cleaning, turn the steamer off by pressing the power

button until the blue power light turns off (about 3 seconds). Unplug,

empty tank, and allow time to cool before storing.

K

J

9

CLEANING FRAMES AND ACCESSORIES

For all accessories, allow to fully dry before using again or storing.

Accessories are not suitable for cleaning in a washing machine.

• Lint frame: Wipe with damp cloth to clean.

• Delicate frame: Wash with cold water and small amounts of gentle

cleanser if needed. The fabric in the frame cannot be removed.

• Upholstery frame: The fabric on this frame can be removed and hand

washed with cold water and gentle cleanser.

STORING THE STEAMER

1. Check that the steamer is unplugged and completely cool.

2. Gather the cord into even ovals and then gently cinch

with the strip of hook and loop. (L)

3. Always store steamer upright on its base to prevent

water leakage.

Tip: Emptying the tank after each use is recommended

because standing water can leave a residue over time.

STEAMING TIPS AND TRICKS

• This steamer is designed to use distilled, puriﬁed, or ﬁltered water. Tap

water contains minerals that build up. Using water with perfumes or

scented additives is also not recommended.

• Always test garments by steaming a small hidden area to make sure the

garment takes well to steam.

• Always read garment care label instructions. Low heat settings require

the delicate fabric frame.

• Small amounts of dripping might occur during use. If excessive, the

steamer needs time to get back up to full temperature. Just allow the

steamer a minute to reheat.

• Wearing clothes immediately after ironing or steaming can actually

create wrinkles. Always allow clothing to cool for about 5 minutes after

ironing or steaming to set the press.

L

10

TROUBLESHOOTING

Problem Possible Cause Solution

The steamer is plugged in

but not heating.

There's a power supply issue. Check that the plug is

properly inserted into the

outlet or try plugging the

steamer into a different outlet.

The auto shut-off has

activated.

Press the steam trigger or

press the power button to

activate the steamer.

Not enough steam or no

steam is coming out of the

steamer.

The steamer is not heated to

full temperature.

Always allow steamer to

preheat at least 45 seconds,

or until the power button

light is a steady blue.

There is not enough water in

the water tank.

Follow the instructions under

the “ﬁlling the water tank”

section and ﬁll to Max level

marker.

The water pump hasn’t been

primed.

After preheating, always

prime the water pump by

holding the steam trigger

until steam forms to ensure

enough water is in the boiler.

Discolored water is coming

through the holes and

staining the fabri

c.

Residue has built up in the

water tank.

Empty the water tank after

each use. Only use distilled,

ﬁltered, or puriﬁed water.

Perfumed or scented

additives were used.

Regularly clean steamer and

refrain from using perfumed

or scented additives.

Steamer is leaking or

spitting.

Steamer is not hot enough. Allow the steamer to heat for

about 45 seconds.

Water tank is running low. Follow the instructions under

the “Filling the Water Tank”

section and ﬁll to Max level

marker.

If additional assistance is needed, please contact our consumer service team at

1-800-231-9786.

11

NEED HELP?

For service, repair or any questions regarding your appliance, please call

our Customer Service Line at 1-800-231-9786. Please DO NOT return the

product to the place of purchase. Also, please DO NOT mail product back to

manufacturer, nor bring it to a service center. You may also want to consult

the website listed on the cover of this pamphlet.

Warranty Information

(Applies only in the United States and Canada)

What does it cover?

• Any defect in material or workmanship provided; however, Spectrum

Brands’ liability will not exceed the purchase price of product.

For how long?

• Two years from the date of original purchase with proof of such purchase.

What will we do to help you?

• Provide you with a reasonably similar replacement product that is either

new or factory refurbished.

How do you get service?

• Save your receipt as proof of date of sale.

• Visit the online service website at www.prodprotect.com/applica, or call

toll-free 1-800-231-9786, for general warranty service.

• If you need parts or accessories, please call 1-800-738-0245.

What does your warranty not cover?

• Damage from commercial use

• Damage from misuse, abuse or neglect

• Products that have been modiﬁed in any way

• Products used or serviced outside the country of purchase

• Glass parts and other accessory items that are packed with the unit

• Shipping and handling costs associated with the replacement of the unit

• Consequential or incidental damages (Please note, however, that some

states do not allow the exclusion or limitation of consequential or

incidental damages, so this limitation may not apply to you.)

How does state law relate to this warranty?

• This warranty gives you speciﬁc legal rights. You may also have other

rights that vary from state to state or province to province.

Page is loading ...

www.BlackAndDeckerAppliances.com

T22-5003177

15005-00

HGS200: 1400 W 120V~ 60 Hz

HGS200C: 1400 W 120V~ 60 Hz

HGS200-CL: 1400 W 220V~ 50 Hz

Comercializado por:

Spectrum Brands de México, S.A de C.V

Autopista México Querétaro

No 3069-C Oficina 004

Colonia San Andrés Atenco, Tlalnepantla

Estado de México, C.P. 54040

Mexico.

Tel: (55) 5831 – 7070

Servicio y Reparación

Art. 123 No. 95

Col. Centro, C.P. 06050

Deleg. Cuauhtemoc

Servicio al Consumidor,

Venta de Refacciones y Accesorios

01 800 714 2503

Importado por / Imported by:

RAYOVAC ARGENTINA S.R.L.

Humboldt 2495 Piso# 3

(C1425FUG) C.A.B.A. Argentina.

C.U.I.T No. 30-70706168-1

Importado por / Imported by:

Spectrum Brands de México, S.A de C.V

Autopista México Querétaro

No 3069-C Oficina 004

Colonia San Andrés Atenco, Tlalnepantla

Estado de México, C.P. 54040

Mexico.

Tel: (55) 5831-7070

Para atención de garantía marque:

01 (800) 714 2503

Importado por / Imported by:

Spectrum Brands

En Chile, Household Products Chile Ltda

Av. Del Valle 570, Ofic. 704

Ciudad Empresarial, Huechuraba

Santiago - Chile

Fono: (562) 2571 3700

Importado por / Imported by:

Spectrum Brands S.A.

Carrera 17 No.89-40

Bogotá, Colombia

Línea de atención al cliente:

018000510012

Sello del Distribuidor:

Fecha de compra:

Modelo:

Código de fecha / Date Code / Le code de date:

Made and Printed in People’s Republic of China.

Fabricado e Impreso en la República Popular de China.

Fabriqué et Imprimé en République populaire de Chine.

BLACK+DECKER and the BLACK+DECKER logo are trademarks of

BLACK+DECKER y el logo tipo BLACK+DECKER son marcas registradas de

BLACK+DECKER et le logo BLACK+DECKER sont des marques de commerce de

All other marks are Trademarks of Spectrum Brands, Inc.

Todas la demás marcas son Marcas Registradas de Spectrum Brands, Inc.

Toutes les autres marques sont des marques de commerce de Spectrum Brands, Inc.

Black & Decker HGS200 Series User manual

This manual is also suitable for

Black & Decker HGS200 Series User manual

in other languages

Related papers

Other documents