Kenmore 4.5 cu. ft. High-Efficiency Top-Load Washer w/ Express Cycle

Kenmore®

Top-Loading High Efficiency

Low-Water Washer

Lavadora de alto rendimiento y carga

superior, con nivel bajo de agua

Laveuse haute efficacité à faible

consommation d’eau avec chargement

par le dessus

P/N W10550315B

Sears Brands Management Corporation

Hoffman Estates, IL 60179 U.S.A.

www.kenmore.com

www.sears.com

Sears Canada Inc.

Toronto, Ontario, Canada M5B 2C3

www.sears.ca

Installation Instructions

Instrucciones de instalación

Instructions pour l'installation

English / Español / Français

Table of Contents / Índice / Table des matières......2

* = color number, número de color, le numéro de la couleur

Models/Modelos/Modèles: 110.2810*

2

WASHER SAFETY

Table of Contents

WASHER SAFETY ��2

INSTALLATION REQUIREMENTS ��3

Tools and Parts �� 3

Location Requirements ��4

Drain System �� 5

Electrical Requirements �� 6

INSTALLATION INSTRUCTIONS ��7

Remove Shipping Materials ��7

Connect Drain Hose ��7

Connect Inlet Hoses �� 8

Level Washer ��10

COMPLETE INSTALLATION

CHECKLIST �� 11

INSTALLATION NOTES

Date of purchase: _____________________

Date of installation: ___________________

Installer: ___________________________

Model number: _______________________

Serial number: _______________________

Date d’achat : _______________________

Date d’installation : ____________________

Installateur : _________________________

Numéro du modèle : ___________________

Numéro de série : _____________________

NOTES CONCERNANT L’INSTALLATION

Índice

SEGURIDAD DE LA LAVADORA ��12

REQUISITOS DE INSTALACIÓN ��13

Herramientas y piezas

��13

Requisitos de ubicación

��14

Sistema de desagüe

��15

Requisitos eléctricos

��15

INSTRUCCIONES DE INSTALACIÓN �� 16

Quite la base y el anillo de embalaje

��16

Conexión de la manguera de desagüe

��17

Conexión de las mangueras de entrada

��18

Nivelación de la lavadora

��19

COMPLETE LA INSTALACIÓN �� 21

Table des matières

SÉCURITÉ DE LA LAVEUSE �� 22

EXIGENCES D’INSTALLATION ��23

Outillage et pièces

�� 23

Exigences d’emplacement

��24

Système de vidange

�� 24

Spécications électriques

�� 25

INSTRUCTIONS D’INSTALLATION ��26

Retrait de la base d’expedition et

de l’emballage en anneau

�� 26

Raccordement du tuyau d’evacuation

�� 26

Raccordement des tuyaux de vidange

�� 27

Mise à niveau de la laveuse

�� 29

LISTE DE VÉRIFICATION

POUR INSTALLATION TERMINÉE ��31

NOTAS SOBRE LA INSTALACIÓN

Fecha de compra: ____________________

Fecha de instalación: __________________

Instalador: __________________________

Número de modelo: ___________________

Número de serie: _____________________

3

INSTALLATION REQUIREMENTS

TOOLS AND PARTS

Gather the required tools and parts before starting installation.

Tools needed:

Pliers that open to 1

9

/

16

"

(39.5 mm)

Flashlight (optional)

Drain hose form

Cable Tie

Adjustable or open end

wrench 9/16" (14 mm)

Wood block

4" min

(102 mm)

Tape measure or ruler Level

Water inlet hoses (2)

Flat inlet hose washers (4)

Parts supplied (located in the washer basket):

Parts needed (Not supplied with washer):

4

Alternate parts (Not supplied with washer):

Your installation may require additional parts. To order, please

refer to the phone number or website on the back page of your

“Use and Care Guide.”

If you have: You will need:

Laundry tub or Sump pump system (if not already

standpipe taller available)

than 96" (2.4 m)

1" (25 mm) 2" (50 mm) diameter to 1" (25 mm)

diameter standpipe diameter Standpipe Adapter Kit,

Part Number 3363920 and

Connector Kit, Part Number 285835

Overhead sewer Standard 20 gal. (76 L) 39" (990 mm)

tall drain tub or utility sink, sump

pump, and connectors (available from

local plumbing suppliers)

Floor drain Siphon Break Kit,

Part Number 285834

Extension Drain Hose,

Part Number 285863

Connector Kit, Part Number 285835

Drain hose too short Extension Drain Hose,

Part Number 285863

Connector Kit, Part Number 285835

Lint clogged drain Drain protector, Part Number 376031

LOCATION REQUIREMENTS

You will need:

■ A water heater set to deliver 120°F (49°C) water to the washer.

■ A grounded electrical outlet located within 4 ft. (1.2 m) of

where the power cord is attached to the back of the washer.

See “Electrical Requirements.”

■ Hot and cold water faucets located within 3 ft. (900 mm)

of the hot and cold water ll valves, and water pressure of

20–100 psi (138–690 kPa) for best performance.

■ Level oor with maximum slope of 1" (25 mm) under entire

washer. Installing the washer on carpet is not recommended.

■ A sturdy oor to support the washer weight (washer, water,

and load) of 315 lbs (143 kg).

IMPORTANT: Do not operate, install, or store washer where it

will be exposed to water, weather, or at temperatures below

32° F (0° C). Some water can remain in washer and can cause

damage in low temperatures. See your “Use and Care Guide”

for information on winterizing.

Proper installation is your responsibility.

Select proper location for your washer to improve performance

and minimize noise and possible “washer walk.” Install your

washer in a basement, laundry room, closet, or recessed area.

To order, please refer to the phone number or website on the

back page of your “Use and Care Guide.”

■ 8212656RP 10 ft. (3.0 m) Inlet hose, Black EPDM (2 pack)

■ 8212641RP 5 ft. (1.5 m) Inlet hose, Black EPDM (2 pack)

■ 8212646RP 4 ft. (1.2 m) Inlet hose, Black EPDM (2 pack)

■ 8212545RP 5 ft. (1.5 m) Inlet hose, Red and Blue EPDM

(2 pack)

■ 8212487RP 5 ft. (1.5 m) Nylon braided inlet hose (2 pack)

■ 8212638RP 6 ft. (1.8 m) Nylon braided inlet hose, space

saving 90° elbow, hypro-blue steel couplings

(2 pack)

■ 8212637RP 6 ft. (1.8 m) Inlet hose, Black EPDM, space

saving 90° elbow, hypro-blue steel couplings

(2 pack)

44"

(1118 mm)

27"

(686 mm)

27.5"

(699 mm)

5

Spacing for recessed area or closet installation

All dimensions show recommended spacing allowed, with tested

spacing of 0" (0 mm) clearance on sides.

■ Additional spacing should be considered for ease of

installation and servicing.

■ Additional clearances might be required for wall, door, and

oor moldings.

■ Additional spacing should be considered on all sides of the

washer to reduce noise transfer.

■ For closet installation, with a door, minimum ventilation

openings in the top and bottom of the door are required.

Louvered doors with equivalent ventilation openings are

acceptable.

■ Companion appliance spacing should also be considered.

* Required spacing

DRAIN SYSTEM

Drain system can be installed using a oor drain, wall standpipe,

oor standpipe, or laundry tub. Select method you need.

Minimum diameter for a standpipe drain: 2" (51 mm). Minimum

carry-away capacity: 17 gal. (64 L) per minute. Top of standpipe

must be at least 39" (990 mm) high; install no higher than

96" (2.44 m) from bottom of washer. If you must install higher

than 96" (2.44 m), you will need a sump pump system.

Wall standpipe drain system

Laundry tub drain system

Minimum capacity: 20 gal. (76 L). Top of laundry tub must

be at least 39" (990 mm) above oor; install no higher than

96" (2.44 m) from bottom of washer.

IMPORTANT: To avoid siphoning, no more than 4.5" (114 mm) of

drain hose should be inside standpipe or below the top of wash

tub. Secure drain hose with cable tie.

Floor drain system

Floor drain system requires a Siphon Break Kit (Part Number

285834), 2 Connector Kits (Part Number 285835), and an

Extension Drain Hose (Part Number 285863) that may be

purchased separately. To order, please see toll-free phone

numbers in your “Use and Care Guide.” Minimum siphon break:

28" (710 mm) from bottom of washer. (Additional hoses may be

needed.)

Floor standpipe drain system

39"

(990 mm)

4.5"

(114 mm)

4.5"

(114 mm)

4.5"

(114 mm)

30"

(762 mm)

39"

(990 mm)

See requirements for oor standpipe drain system.

3"

(76 mm)

3"

(76 mm)

24 in.

2

(155 cm

2

)

48 in.

2

(310 cm

2

)

17"

(432 mm)

1"

(25 mm)

1"

(25 mm)

5"

(126 mm)

14" max.

(356 mm)

*

6

ELECTRICAL REQUIREMENTS

■ A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical

supply is required. A time-delay fuse or circuit breaker on a

separate circuit serving only this washer is recommended.

■ This washer is equipped with a power supply cord having a

3-prong grounding plug.

■ To minimize possible shock hazard, the cord must be plugged

into a mating, 3-prong, grounding-type outlet, grounded in

accordance with local codes and ordinances. If a mating outlet

is not available, it is the personal responsibility and obligation

of the customer to have the properly grounded outlet installed

by a qualied electrician.

■ If codes permit and a separate ground wire is used, it is

recommended that a qualied electrician determine that the

ground path is adequate.

■ Do not ground to a gas pipe.

■ Check with a qualied electrician if you are not sure the

washer is properly grounded.

■ Do not have a fuse in the neutral or ground circuit.

7

INSTALLATION

INSTRUCTIONS

Before you start: remove shipping materials.

It is necessary to remove all shipping materials for proper

operation and to avoid excessive noise from washer.

NOTE: To avoid oor damage during installation, set the washer

onto cardboard before moving across the oor.

IMPORTANT:

■ Be sure the foam shipping base has been removed from the

bottom of the washer as directed in the “Remove Shipping

Base and Packing Ring” section.

■ If foam shipping base has not been removed, be sure lid is

secured with tape before laying washer on its back.

■ Removing the foam shipping base is necessary for proper

operation.

Place cardboard supports from shipping carton on oor behind

washer for support. Secure the lid with tape. Using two or more

people, tip the washer onto its back and place on cardboard

supports. Remove foam shipping base. Then, set washer back

upright, and remove the tape from the lid so that you can open

the lid and remove the foam packing ring from the washer tub.

NOTE: Keep foam packing ring in case you need to move

the washer in the future.

REMOVE SHIPPING BASE

AND PACKING RING

1� Remove shipping base and packing ring

CONNECT DRAIN HOSE

Gently pull hose out of back of washer cabinet from top until

end emerges.

IMPORTANT: Do not force excess drain hose back into rear of

washer.

IMPORTANT: Proper connection of the drain hose helps to avoid

water leakage and damage to your oors. The drain hose is

connected to your washer and is stored inside the washer cabinet.

For a laundry tub or standpipe drain, connect the drain hose

form. For a oor drain, do not install drain hose form. You may

need alternate parts with separate directions. See “Tools and

Parts” to determine what you may need.

Feed hose into one end of form. Bend hose and feed through

other side, anchoring form on smooth sections of hose. The

hose must extend 4.5" (114 mm) beyond the form.

2� Connect drain hose form

1� Remove drain hose from washer cabinet

8

Make sure the washer basket is empty. Attach the hose labeled

hot to hot water faucet. Screw on coupling by hand until it is

seated on washer. Use pliers to tighten couplings an additional

two-thirds turn. Repeat this step with the hose labeled cold for

the cold water faucet. Both hoses must be connected for washer

to work properly.

IMPORTANT: Do not overtighten or use tape or sealants on

valve when attaching to faucets or washer. Damage can result.

HELPFUL TIP: Make note of which hose is connected to hot

water to help in attaching hoses to washer correctly.

2� Connect inlet hoses to water faucets

Place hose into standpipe (shown in picture) or over side of

laundry tub.

IMPORTANT: To keep drain water from going back into the

washer:

Do not force excess drain hose into standpipe. Hose should be

secure but loose enough to provide a gap for air.

Do not lay excess hose on the bottom of the laundry tub.

4.5"

(114 mm)

3� Place drain hose in standpipe

CONNECT INLET HOSES

IMPORTANT: To avoid leaks, check that your water inlet hoses

have at washers at both ends. Washer must be connected

to water faucets with new inlet hoses with at washers (not

provided). Do not use old hoses. Do not use hoses without

washers.

A B

A. Coupling

B. Washer

1� Insert new at washers

9

Attach hot water hose to hot water inlet valve. Screw coupling

by hand until it is snug. Use pliers to tighten couplings an

additional two-thirds turn. Repeat with cold water inlet valve.

Both hoses must be connected for washer to work properly.

IMPORTANT: Do not overtighten or use tape or sealants on

valve when attaching to faucets or washer. Damage can result.

NOTE: To reduce risk of hose failure, replace the hoses every

5 years. Record hose installation or replacement dates for

future reference.

Periodically inspect and replace hoses if bulges, kinks, cuts,

wear, or leaks are found.

Turn on water faucets to check for leaks from faucet and at

washer connection. A small amount of water may enter washer.

You will drain this in a later step.

4.5"

(114 mm)

4.5"

(114 mm)

4.5"

(114 mm)

Laundry Tub Standpipe Wall

Secure drain hose to laundry tub leg, drain standpipe, or inlet

hoses for wall standpipe with cable tie (A). This will help reduce

the chance of drain water splashing on the oor.

A

6� Secure drain hose

4� Connect inlet hoses to washer

5� Check for leaks

Run water for a few seconds through hoses into a laundry tub,

drainpipe, or bucket to avoid clogs. Water should run until clear.

Check the temperature of the water to make sure that the hot

water hose is connected to the hot water faucet and the cold

water hose is connected to the cold water faucet.

3� Clear water lines

10

If the washer is not level, move

the washer out slightly, tip back

and prop up the front of the washer with a wood block. Adjust

the right front foot by loosening the locknut with a 9/16" or

14 mm open-end wrench, then twisting the foot up or down as

needed. After the washer is level, make sure all 4 feet are in

rm contact with the oor by gently rocking it back and forth

and side to side. Adjust the feet if necessary, then using the

wrench again, turn the locknuts counterclockwise on the foot to

tighten to the washer cabinet.

HELPFUL TIP: You may have to adjust the back feet to level the

washer. If you are installing the washer in a tight or hard-to-

reach area, you may have to move the washer out to reach the

feet comfortably. You may wish to lock the back feet before

moving the washer back into place.

IMPORTANT: If the locknuts are not tight against the washer

cabinet, the washer may vibrate.

4� Adjust levelness of washer

LEVEL WASHER

IMPORTANT: Leveling your washer properly reduces excess noise

and vibration.

For washers with an adjustable right front foot, lower the right

front foot until it contacts the oor. Using pliers, rotate the foot

up to an additional 1

1

/

2

turns.

Move the washer to its nal location. Rock the washer back

and forth to check whether all four feet are stable and in rm

contact with the oor. If the washer rocks, your model may

be one that comes with 3 feet preset at the factory. It will be

necessary to adjust the right front foot to level the washer. If

all 4 feet were preset at the factory, minor adjustments may be

needed to level the washer on your oor.

Check the levelness of the washer. First, place a level on the lid

near the console. Then place the level on the side of the washer

in the crease between the top of the washer and the cabinet.

Not Level Not Level LEVEL

2� Adjust front leveling foot

3� Check levelness of washer

1� Move washer to nal location

Place level here

Place level here Place level here

11

COMPLETE INSTALLATION

CHECKLIST

■ Check electrical requirements. Be sure you have correct

electrical supply and recommended grounding method.

See “Electrical Requirements.”

■ Check that all parts are now installed. If there is an extra part,

go back through steps to see what was skipped.

■ Check that you have all of your tools.

■ Keep the foam packing ring from the washer tub for future

relocation of the washer. Dispose of/recycle all packaging

materials.

■ Check that both water faucets are on.

■ Check for leaks around faucets and inlet hoses.

■ Remove lm from console and any tape remaining

on washer.

■ Check that washer is plugged into a grounded 3-prong outlet.

■ Read “Washer Use” in your “Use and Care Guide.”

■ To test and clean your washer, measure 1/2 of normal

recommended amount of High Eciency (HE) powdered

or liquid detergent for a medium-size load and pour it into

detergent dispenser. Close lid. Press POWER. Select a normal

cycle and press START. Allow it to complete

one whole cycle.

5� Plug into a grounded 3 prong outlet

Page is loading ...

W10550315B

8/13

Printed in U.S.A.

Impreso en EE.UU.

Imprimé aux É-U

® Registered Trademark /™ Trademark of KCD IP, LLC in the United States, or Sears Brands, LLC in other countries

® Marca Registrada /™ Marca de Fábrica de KCD IP, LLC en Estados Unidos, o Sears Brands, LLC in otros paises

MC

Marque de commerce /

MD

Marque déposée de Sears Brands, LLC

® Registered Trademark /

TM

Trademark of KCD IP, LLC in the United States, or Sears Brands, LLC in other countries

® Marca Registrada /

TM

Marca de Fábrica de KCD IP, LLC en Estados Unidos, o Sears Brands, LLC in otros países

MC

Marque de commerce /

MD

Marque déposée de Sears Brands, LLC

Get it fixed, at your home or ours!

Your Home

For troubleshooting, product manuals and expert advice:

www.managemylife.com

For repair – in your home – of all major brand appliances,

lawn and garden equipment, or heating and cooling systems,

no matter who made it, no matter who sold it!

For the replacement parts, accessories and

owner’s manuals that you need to do-it-yourself.

For Sears professional installation of home appliances

and items like garage door openers and water heaters.

1-800-4-MY-HOME

®

(1-800-469-4663)

Call anytime, day or night (U.S.A. and Canada)

www.sears.com www.sears.ca

Our Home

For repair of carry-in items like vacuums, lawn equipment,

and electronics, call anytime for the location of your nearest

Sears Parts & Repair Service Center

1-800-488-1222 (U.S.A.) 1-800-469-4663 (Canada)

www.sears.com www.sears.ca

To purchase a protection agreement on a product serviced by Sears:

1-800-827-6655

(U.S.A.)

1-800-361-6665

(Canada)

Para pedir servicio de reparación

a domicilio, y para ordenar piezas:

1-888-SU-HOGAR

®

(1-888-784-6427)

www.sears.com

Au Canada pour service en français:

1-800-LE-FOYER

MC

(1-800-533-6937)

www.sears.ca

Kenmore 4.5 cu. ft. High-Efficiency Top-Load Washer w/ Express Cycle - White ENERGY STAR Installation guide

Kenmore 4.5 cu. ft. High-Efficiency Top-Load Washer w/ Express Cycle - White ENERGY STAR Installation guide

in other languages

Related papers

Other documents