Miele DA 2280 User manual

Brand: Miele

Model: DA 2280

Category: Cooker hoods

Type: User manual

This manual is also suitable for

28228055USA

Miele DA 2280 is a ventilation system that helps to remove cooking odors and smoke from your kitchen. With its powerful motor and efficient filtration system, the DA 2280 can effectively clean the air in your kitchen, leaving it fresh and odor-free.

The DA 2280 is easy to operate, with a simple joystick control panel that allows you to quickly and easily adjust the fan speed and lighting. The system also features a convenient delayed shut-off function, which allows you to set a timer for the fan to turn off automatically after a certain amount of time.

The DA 2280 comes with two grease filters and an active charcoal filter, which work together to remove grease, odors, and smoke from the air. The grease filters are dishwasher-safe for easy cleaning, and the active charcoal filter can be replaced as needed.

Operating and Installation

Instructions

Ventilation System

DA 2280

DA 2210

To prevent accidents

and appliance damage,

read these instructions

before

installation or use.

M.-Nr. 07 773 240

en - US, CA

IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Guide to the Ventilation System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Joystick .........................................................10

Turning on the fan .................................................10

Selecting the power level............................................10

Delayed Shut Down ................................................11

Turning off the fan .................................................11

Overhead lighting .................................................12

Filter timers ......................................................13

Checking the filter timers ............................................13

Reprogramming the timers ..........................................14

Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Cleaning the casing................................................16

Grease filters .....................................................17

Active charcoal filter ...............................................19

Changing the light bulb .............................................20

After Sales Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Caring for the environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Appliance dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Distance between cooktop and hood (S) ...............................27

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Installing the joystick ...............................................31

Joystick extension .................................................31

Electrical connection ...............................................32

Air extraction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Electrical connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Contents

READ AND SAVE THESE

INSTRUCTIONS

Keep these instructions in a safe

place and pass them on to any future

user.

Read these instructions carefully

before installing or using the

Ventilation System.

This appliance is intended for

residential use only. Use the appliance

only for its intended purpose.

This appliance complies with current

safety requirements. Improper use of

the appliance can lead to personal

injury and material damage.

,CAUTION

For General Ventilating Use

Only. Do Not Use To Exhaust

Hazardous Or Explosive

Materials And Vapors.

This appliance is designed to vent

cooking smoke and odors only.

This appliance is suitable for

installation above gas or electric

cooking surfaces.

This appliance is not intended for

outdoor use.

This appliance must not be used in

a non-stationary location (e.g. on a

ship).

,WARNING

TO REDUCE THE RISK OF

FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

a) Use this appliance only in the

manner intended by the manufacturer.

If you have questions, contact Miele.

b) Before servicing or cleaning the

appliance, switch power off at the

service panel and lock the service

disconnecting means to prevent power

from being switched on accidentally. If

the service disconnecting means

cannot be locked, securely fasten a

prominent warning device, such as a

tag, to the service panel.

c) Be certain your appliance is

properly installed and grounded by a

qualified technician.

To guarantee the electrical safety of this

appliance, continuity must exist

between the appliance and an effective

grounding system. It is imperative that

this basic safety requirement be met. If

there is any doubt, have the electrical

system of the house checked by a

qualified electrician.

IMPORTANT SAFETY INSTRUCTIONS

d) Before connecting the appliance

to the power supply make sure that the

voltage and frequency listed on the

data plate correspond with the

household electrical supply.

This data must correspond to prevent

appliance damage. If in doubt consult a

qualified electrician.

e) Installation work and repairs

should only be performed by a qualified

technician in accordance with all

applicable codes and standards.

Repairs and other work by unqualified

persons could be dangerous.

f) Only open the housing as

described in the enclosed "Installation

diagram" and in the "Cleaning and care"

section of this manual. Under no

circumstances should any other parts

of the housing be opened. Tampering

with electrical connections or

components and mechanical parts is

highly dangerous to the user and can

cause operation faults.

g) Before discarding an old

appliance, disconnect it from the power

supply and remove the power cord to

prevent hazards.

Use

,WARNING

TO REDUCE THE RISK OF A

COOKTOP GREASE FIRE:

a) Never leave surface units

unattended at high settings. Boilovers

cause smoking and greasy spillovers

may ignite. Heat oils slowly on low or

medium settings.

b) Always turn the hood on when

cooking at a high heat.

c) Clean the ventilation hood

frequently. Grease should not be

allowed to accumulate on the fan or

filter.

d) Use the proper pan size. Always

use cookware appropriate for the size

of the cooking area.

e) Do not flambé or grill with an

open flame beneath the hood.

Flames could be drawn up into the

hood by the suction and the grease

filters may catch fire.

IMPORTANT SAFETY INSTRUCTIONS

,WARNING

TO REDUCE THE RISK OF

INJURY TO PERSONS IN THE

EVENT OF A COOKTOP

GREASE FIRE, OBSERVE THE

FOLLOWING

a) SMOTHER FLAMES with a close

fitting lid, cookie sheet, or metal tray

then turn off the burner.

BE CAREFUL TO PREVENT BURNS.

If the flames do not go out immediately,

EVACUATE AND CALL THE FIRE

DEPARTMENT.

b) NEVER PICK UP A FLAMING

PAN - You may be burned.

c) DO NOT USE WATER, including

wet dishcloths or towels - a violent

steam explosion will result.

d) Use a fire extinguisher ONLY if:

1) You have a class ABC

extinguisher, and you know how to

operate it.

2) The fire is small and contained in

the area where it started.

3) The fire department is being

called.

4)You can fight the fire with your

back to an exit.

Based on "Kitchen Firesafety Tips"

published by NAFTA

Do not allow children to play with or

operate the appliance or its controls.

Supervise its use by the elderly or

infirm.

Always turn on the hood when using

the cooktop to prevent damage from

condensation.

Never operate gas burners without

cookware. Turn the burner off when not

in use. Adjust the burner so that the

flames do not extend beneath the

cookware. Do not overheat the

cookware, e.g. when using a wok. The

hood can be damaged due to

excessive heat from the burners and

the cookware.

Do not use the hood without the

grease filters in place.

Do not use a steam cleaner to clean

the hood. Steam could penetrate

electrical components and cause a

short circuit.

IMPORTANT SAFETY INSTRUCTIONS

Installation

,WARNING

TO REDUCE THE RISK OF

FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

a) Installation work and electrical

wiring must be done by qualified

person(s) in accordance with all

applicable codes and standards,

including fire-rated construction.

b) Sufficient air is needed for

combustion and exhausting of gases

through the flue (chimney of fuel

burning equipment to prevent back

drafting. Follow the heating equipment

manufacturer’s guideline and safety

standards such as those published by

the National Fire Protection Association

(NFPA) and the American Society for

Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), and

the local code authorities.

c) When cutting or drilling into the

wall or ceiling, do not damage electrical

wiring and other hidden utilities.

d) Ducted hoods must always be

vented to the outdoors.

e) Do not use this hood with any

solid-state speed control device.

f) Do not use an extension cord to

connect the appliance to electricity.

Extension cords do not guarantee the

required safety of the appliance,

(e.g. danger of overheating).

g) Do not install this hood over

cooktops that burn solid fuel.

h) Provided a larger distance is not

given by the manufacturer of the

cooktop, follow the minimum safety

distances between a cooktop and the

bottom of the hood given in the

"Appliance dimensions" section of this

manual.

If local building codes require a greater

safety distance, follow their

requirement.

If there is more than one appliance

beneath the hood and they have

different minimum safety distances

always select the greater distance.

i) Never connect an exhaust hood to

an active chimney, dryer vent, vent flue,

or room ventilating ductwork.

j) Seek professional advice before

connecting an exhaust hood vent to an

existing, inactive chimney or vent flue.

k) Any fittings, sealant, or materials

used to install the ductwork must be

made of approved non-flammable

materials.

,WARNING

TO REDUCE THE RISK OF

FIRE USE ONLY METAL

DUCTWORK.

IMPORTANT SAFETY INSTRUCTIONS

The ventilation hood offers two modes

of operation:

Air extraction

The air is drawn in and cleaned by the

grease filters and directed outside.

The hood comes equipped with a

non-return flap. This flap automatically

closes when the hood is turned off so

that no exchange of outside air and

room air can occur. When the hood is

turned on, the air pressure of the

exhaust fan automatically opens the

flap blowing the inside air and cooking

odors outside.

The DA 2280 is equipped with one

non-return flap, the DA 2210 comes

with two non-return flaps.

Recirculation mode

Air is drawn through the grease filters

and active charcoal filters. The filtered

air is then recirculated back into the

kitchen.

The active charcoal filter and the

installation kit may be purchased from

Miele.

Before using the hood in

recirculation mode, ensure that the

active charcoal filters are in place,

see "Cleaning and Care".

Functional description

Guide to the Ventilation System

a Control panel

b Joystick

The fan and light can be operated with

the joystick.

c Overhead lighting

d Charcoal filters

optional accessory for recirculation

mode

DA 2280: 2 filters

DA 2210: 4 filters

e Grease filters

f Fan power selection

g Delayed Shut Down

This button activates the Delayed Shut

Down feature. The fan can be set to

turn off automatically after either 5 or

15 minutes.

h Grease filter button

The indicator next to the grease filter

button lights when the grease filters

need to be cleaned. This button is also

used:

–

to reset the grease filter timer after

cleaning the grease filters (see

"Cleaning and Care").

–

to show how long the grease filters

have been in use (see "Operation/

Filter timers").

–

to change the number of hours

counted by the grease filter timer

(see "Operation/Reprogramming the

timers").

i Charcoal filter button

The indicator next to the charcoal filter

button lights when the charcoal filters

need to be replaced.

This button is also used:

–

to reset the charcoal filter timer after

changing the filter (see "Cleaning

and care").

–

to show how long the charcoal filters

have been in use (see "Operation/

Filter timers").

–

to change the number of hours

counted by the charcoal filter timer

(see "Operation/Reprogramming the

timers").

Guide to the Ventilation System

Joystick

The joystick controls the fan power and

overhead lighting.

Turning on the fan

^ Press the joystick once to the right.

The fan runs at power level "2" and the

second indicator of the fan power scale

lights.

Selecting the power level

Press the joystick to the right, to

increase the fan speed. Press it to

the left to decrease the fan speed.

The corresponding fan power indicator

lights.

Level "1" to "3" are usually sufficient for

normal cooking.

Intensive setting

Level "4" should be used for a short

period when frying or cooking food with

a strong aroma.

Fan performance

DA 2280

The maximum air flow capacity is

425 cfm. Factors such as narrow duct

diameters and bends will affect this

value.

DA 2210

The maximum air flow capacity is

850 cfm. Factors such as narrow duct

diameters and bends will affect this

value.

Level 1 operates at 40% capacity

Level 2 operates at 60% capacity

Level 3 operates at 80% capacity

Level 4 operates at 100% capacity

There will also be a slight decrease in

airflow for hoods operated in

recirculation mode due to the active

charcoal filters.

Operation

Automatically switching back to the

"Intensive" setting

The intensive level "4" can be

programmed to automatically switch

back to level "3" after 10 minutes.

Turn the fan and the lights off.

Press and hold the Delay Shut Down

button for 10 secs. The first indicator

of the fan power levels lights.

Press the joystick once either

backwards or forwards.

The second indicator lights.

^ Press the joystick once to the left.

The third indicator lights.

^ Press the joystick again either once

backwards or once forwards.

If the power level indicators "1" and "4"

flash the automatic switch back is not

activated.

To activate the automatic switch

back

Press the joystick once to the right.

The power level indicators "1" and "4"

light.

To deactivate the automatic switch

back

Press the joystick once to the left.

Press the Delay Shut Down button to

confirm the setting.

Delayed Shut Down

If odors or smoke remain in the kitchen

after cooking has been completed, the

Delayed Shut Down feature can be

selected to allow the hood to continue

running for either 5 or 15 minutes.

Press the Delayed Shut Down button

while the fan is still running:

Press once = 5 minutes delay

(left indicator lights)

Press twice = 15 minutes delay

(right indicator lights)

^ To cancel the Delayed Shut Down

feature press the button again.

Turning off the fan

^ Hold the joystick to the left until the

fan shuts off and the fan power

indicators go out.

Automatic Safety Shut Off

The fan will turn off automatically

10 hours after the last movement of the

joystick. The lighting remains on.

Press the joystick once to the right to

turn the fan back on again.

Operation

Overhead lighting

The overhead lighting can be turned on

and off independently of the fan.

^ To turn the light on or off, press the

joystick either once backwards or

once forwards.

Dimming the lighting

The brightness of the lighting can be

adjusted.

While the lighting is turned on, press

and hold the joystick backwards or

forwards.

The lighting will dim until the joystick

is released.

If the joystick is pressed again, the

lighting will brighten until the joystick

is released.

If the joystick is pressed continuously,

the light will cycle between bright and

dark.

Operation

Filter timers

Grease filter timer

A timer monitors the hours of operation.

The indicator for the grease filter will

light after 30 hours of fan operation. The

grease filters must then be cleaned.

After the grease filters have been

cleaned and put back in place, the

grease filter timer must be reset.

^ To do this press the grease filter

button for about 3 seconds.

The indicator will go out.

To change the hours of operation, see

"Reprogramming the timers".

Charcoal filters

The timer for the charcoal filter is not

preset. To program this timer, see

"Operation / Reprogramming the

charcoal filter timer". The charcoal filter

indicator will light, once the selected

time has elapsed. The charcoal filters

must then be replaced and the

charcoal filter timer must be reset.

To do this, press the charcoal filter

button for about 3 seconds.

The indicator will go out.

Checking the filter timers

To check the percentage of time set

already used:

Press the joystick to the left to turn

the fan on.

^ Press the grease filter or charcoal

filter button.

The number of flashing indicators show

the percentage of programmed hours

that have been used.

1 indicator = 25 %

2 indicators = 50 %

3 indicators = 75 %

4 indicators = 100 %

This information will remain stored in

memory in the event of a power failure.

Operation

Reprogramming the timers

The grease filter timer is preset to 30

hours. This time can be lengthened or

shortened to 20, 30, 40 or 50 hours.

–

A time of 20 hours should be

programmed in kitchens with

frequent pan or deep frying.

–

A time of 20 hours should also be

programmed if the kitchen is only

used occasionally. Otherwise grease

which has accumulated over a long

period of time will harden on the

filters making cleaning more difficult.

Reprogramming the grease filter

timer

^ Press the joystick to the left to turn

the fan off.

^ Press the Delayed Shut Down and

the grease filter buttons at the same

time.

The grease filter indicator and one of

the fan power indicators will flash.

The fan power indicators show the

programmed time:

1st indicator from the left = 20 hours

2nd indicator from the left = 30 hours

3rd indicator from the left = 40 hours

4th indicator from the left = 50 hours

Use the joystick to select the desired

time. Press it to the left for a shorter

operating time, to the right for a

longer operating time.

^ Store the selection by pressing the

grease filter button.

All indicators will go out.

If the procedure is not stored within

4 minutes of programming the hood will

automatically default to the "old" data.

Operation

Reprogramming the charcoal filter

timer

The active charcoal filters can only be

used in recirculation mode and cannot

be used to exhaust fumes.

The charcoal filter timer is not preset.

Before using the hood in recirculation

mode, the charcoal filter timer must be

programmed.

Press the joystick to the left to turn

the fan off.

^ Press the Delayed Shut Down and

charcoal filter buttons at the same

time.

The indicator for the charcoal filter and

one of the fan power scale indicators

will flash.

The indicators of the fan power scale

show the programmed time:

1st indicator from the left = 120 hours

2nd indicator from the left= 180 hours

3rd indicator from the left= 240 hours

4th indicator from the left = unlimited

Use the joystick to select the desired

time. Press it to the left for a shorter

operating time, to the right for a

longer operating time.

^ Store the selection by pressing the

charcoal filter button.

All indicators will go out.

If the procedure is not stored within 4

minutes of programming, the hood will

automatically default to the "old" data.

Operation

,WARNING

TO REDUCE THE RISK OF

FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

Before cleaning or servicing the

hood, disconnect it from the power

supply, see "Important Safety

Instructions".

The halogen bulbs are very hot

when in use. They stay hot for some

time after turned off. Use caution,

danger of burns.

Wet cleaning the hot bulbs will

cause damage.

Wait a few minutes after turning

them off before cleaning.

Cleaning the casing

Never use abrasive cleaners,

scouring pads, steel wool or caustic

(oven) cleaners on the hood. They

will damage the surface.

All external surfaces and controls can

be cleaned with a mild solution of

warm water and liquid dish soap

applied with a soft sponge.

Wipe dry using a soft cloth.

Do not use too much water when

cleaning the controls. Water could

penetrate into the electronics and

cause damage.

Avoid:

–

cleaning agents containing soda,

acids or chlorides,

–

abrasive cleaning agents

e.g. powder or cream cleansers,

–

abrasive sponges, e.g. pot scourers

or sponges which have been

previously used with abrasive

cleaning agents,

–

limescale removers.

These will damage the surface.

Stainless steel colored controls

These controls may become dis-

colored or damaged if not cleaned

regularly.

Do not use a stainless steel cleaner

on these controls.

Cleaning and care

Grease filters

The reusable metal grease filters

remove solid particles from the vented

kitchen air (grease, dust, etc).

The grease filters should be cleaned

every3-4weeks, when the grease

filter indicator lights, or when they are

visibly dirty, whichever comes first.

A dirty filter is a fire hazard.

To remove the grease filters pull the

locking clips forward. Lower the filter

45° unhook it at the rear and take it

out. Support the grease filters so that

they do not fall onto the cooktop.

Cleaning the grease filters

By hand: use a scrub brush with a

solution of warm water and mild

detergent.

Do not use pure detergent,

aggressive all purpose cleaners,

oven sprays or limescale removers.

They could destroy the filters.

In a dishwasher: place the filters

vertically in the lower basket, making

sure that the spray arm is not

blocked.

Use a wash program with a max.

temperature of 150°F (65°C). In a

Miele dishwasher use the "Normal"

program.

Use the recommended amount of

dishwasher detergent. Overuse could

destroy the filter.

Depending on the detergent,

cleaning the grease filters in a

dishwasher may cause permanent

discoloration of the filter surface.

Performance of the filter will not be

affected by this discoloration.

After cleaning, the filters can be

placed on a towel to air dry.

While the filters are removed, clean

any dirt or grease from the filter

casing to prevent the risk of fire.

Cleaning and care

Inserting the grease filters

When putting the grease filters back

make sure that the locking clips are

visibly facing the cooking surface.

If the filters are incorrectly installed,

insert a small screwdriver into the slit

along its edge to disengage it from the

casing.

^ After returning the grease filters,

press and hold the grease filter

button for 3 seconds to reset the

timer. The indicator light will go out.

^ If the grease filters are cleaned

before the grease filter timer has

reached its maximum, press the

grease filter button for 6 seconds to

reset the counter to zero.

Cleaning and care

Active charcoal filter

DA 2280 uses 2 active charcoal filters

DA 2210 uses 4 active charcoal filters

In recirculation mode active charcoal

filters must be used in addition to the

grease filters. It is designed to absorb

cooking odors.

The active charcoal filters will be

replaced in the canopy above the

grease filters.

Replacement active charcoal filters

can be ordered from Miele.

^ Remove the grease filters to access

the charcoal filters. See "Cleaning

and Care - Grease filters".

Insert the charcoal filters.

Before using:

Program the charcoal filter timer, see

"Operation / Reprogramming the

charcoal filter timer".

Replace the active charcoal filters when

the charcoal filter indicator lights, at

least every 6 months or when they no

longer absorb odors efficiently.

After replacing the charcoal filters,

press and hold the charcoal filter

button for about 3 seconds to reset

the charcoal filter timer.

The indicator light will go out.

If the charcoal filters are replaced

before the timer has reached its

maximum, the charcoal filter button

should be pressed for 6 seconds to

reset the counter to zero.

Cleaning and care

Changing the light bulb

,WARNING

TO REDUCE THE RISK OF

FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

Before changing the light bulbs,

disconnect the hood from the power

supply, see "Important Safety

Instructions".

When in use halogen bulbs become

extremely hot, and they can burn

your hands. Do not attempt to

change the bulbs until they have

had sufficient time to cool down.

Do not touch the bulb surface.

Fingerprints or body oils deposited

on the bulb will decrease the life of

the bulb.

Follow the bulb manufacturer’s

instructions.

Remove the grease filters.

If existent remove the active charcoal

filters.

^ Reach through the grille opening and

push the light fixture downwards.

^ Turn the bulb counterclockwise and

pull it out of its socket.

^ Replace the bulb with a new one

(GU/GZ 10, 120V, 50W) in the

reverse order and push upwards.

Return the grease filters and if

existent the active charcoal filters.

Cleaning and care

Page is loading ...

Miele DA 2280 User manual

Brand: Miele

Model: DA 2280

Category: Cooker hoods

Type: User manual

This manual is also suitable for

28228055USA

Download PDF

report

Miele DA 2280 User manual

This manual is also suitable for

Miele DA 2280 User manual

Related papers

Other documents