Frigidaire 1135244 Installation guide

1135244
Frigidaire
Brand
Frigidaire
Model
1135244
Category
Dishwashers
Type
Installation guide
SERVICE DATA SHEET
P/N: A13707601RevA
Artwork: A06401801Rev001
This information is intended for use by persons having electrical and
mechanical training and a level of knowledge of these subjects generally
considered acceptable in the appliance repair trade. Electrolux Home
Products North America cannot be responsible, nor assume any liability,
for injury or damage of any kind arising from the use of this Service
Data Sheet.
BK............Black
BU............Blue
PK............Pink
R..............Red
Vio...........Violet
W.............White
Y..............Yellow
R-Y.........Red/Yellow
COLOR CODE
OPERATION
WARNING
DISPLAY CODES (LED)
WIRING DIAGRAM
CYCLE SELECTION OPTIONS
To start ----------------- Close door fully to latch. Press START/CANCEL pad.
To delay start --------- Close door fully to latch. Press DELAY START pad to select desired
delay time.
To select a new cycle
or option ------------- Press desired cycle and/or option pad.
The indicator lights will change. Press START/CANCEL within
15 seconds to begin cycle.
To cancel
a cycle ---------------- Hold START/CANCEL pad for 3 seconds, the dishwasher will drain for
90 seconds, then shut off.
Disconnect electrical power at
the fuse box or circuit breaker
box before servicing under
this product. Electrical power
may be present on some parts
under this product, even if
not in use.
Failure to follow this warning
could result in serious injury or
death.
Interval Number
Description
1
2
6
4
3
5
7
8
Fill/Det. Dispenser
Fill
Wash/Heat
Wash/Heat/Det. Disp.
Wash/Heat
Pause/Heat
Drain
Drain/Dry/Heat
End State
Interval Duration Sec.
60
27
60
0.4
75
60
90
90
Water Valve
Circulation Motor
Drain Motor
Heater
Dispenser
Clean LED
0
1
0
1
1
1
1
1
1
1
1
1
1
0
1
0
0
0
0
0
0
0 1
0
0
0
0
0
0
0
0 0
0
0
0
0 0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0 0
1
0
1
0
Clean LED stays on until door is opened or cycle is started
Notes
0 0 0 0 0 1
WATER/SERVICE TEST
The water/service test, (WST)
is a special function initiated
from the power failure mode.
While in power failure mode -
simultaneously press the OPTIONS
and START/CANCEL pads for one
second.
The dishwasher will then step
through the test cycle per the
chart. Pushing the START/CANCEL
pad will advance the dishwasher
to the next step.
Pre-Wash 1
Minutes
Normal (HT)
Water Valve
Heavy Wash
5
10 15 20
25 30 35 40 45
50 55 60
65 70
75
80 85
90 95
100
105
110
115
120
125 5
10
15
20
5
10
15 20 25 30
35 40 45
Pre-Wash 2
Pre-Wash 3
Main Wash
Rinse 1
Rinse 2
Rinse 3 Final Rinse
Dry
Circulation Motor
Drain Motor
Heater
Dispenser
Water Valve
Circulation Motor
Drain Motor
Heater
Dispenser
Pre-Wash 1
Pre-Wash 2
Pre-Wash 3
Main Wash
Rinse 1 Final Rinse Dry
Pre-Wash 4
Minutes
Water Valve
*Rinse Only
Circulation Motor
Drain Motor
Heater
Dispenser
Pre-Wash 1
Pre-Wash 2
50 55 60 65 70 75 80 85 90
Normal
Minutes
Water Valve
Circulation Motor
Drain Motor
Heater
Dispenser
Pre-Wash 1
Main Wash
Rinse 1
Dry
*Energy Saver
Minutes
5
10 15
20
25 30 35 40 45
50 55
60
65 70
Pre-Wash 1
Main Wash
Final Rinse
Water Valve
Circulation Motor
Drain Motor
Heater
Dispenser
75 80
Rinse 1
Dry
Vent
Vent
Vent
Final Rinse
Vent
Vent
K4 03-05-14 (2014 ESTAR)
Note: The Main Wash and Final Rinse
may be lengthened when needed to reach
optimal wash temperatures.
130 135
* Some Models
SANITIZED ----------The SANITIZATION criteria has been met. Indicator
light switch off after 15 seconds of door open.
CLEAN---------------- Shows Completion of cycle. Indicator light will
switch off after 15 seconds of door open.
ALL LED’s
illuminated solid-----All LED’s illuminated solid indicates power failure has occured.
Press START/CANCEL pad and re-select desired options and
cycles.
START LED
fl ashing---------------The START LED will fl ash when the door is opened. Close the
door and press START/CANCEL to resume cycle.
STATUS LED’S
fl ashing---------------An error has occured.
Sanitize LED (if available)
When the control advances to the
“dry” portion of the cycle heated,
moist air leaves the dishwasher
through the console vent. Drier air
is then drawn into the unit through
vents at the bottom of the door. Heat
stored in the dishware causes the
water on the dishes to evaporate into
the drier air.
TROUBLE SHOOTING TIPS
Tub Interior
Mounting Rib
Pump Assembly
This process continues throughout the
drying phase as the heating element is
turned ON and OFF.
Detergent and Rinse Aid Dispenser
The detergent and rinse aid dispenser
is a one piece component consisting
of a molded detergent cup and a
built-in rinse aid dispenser.
The detergent cup has a spring
loaded cover and the rinse aid
dispenser has a removeable cover.
To re-fi ll, remove the cap and pour
rinse aid in until the level shows
above the bottom of the cylindrical
opening and the sight gauge changes
appearance. If any is spilled wipe
it up before starting the cycle. The
amount of rinse aid released
can be adjusted by turning the arrow
indicator from one, being the least
amount, to four, being the greatest
amount.
To replace dispenser:
• shut off electricity to dishwasher,
• remove outer door panel assembly,
• disconnect wiring to the actuator,
• remove the six screws,
• remove the dispenser,
• replace and reinstall screws,
• rewire actuator.
Standard Dry Air Flow
Tub and Door Seal
Product Specifi cations
Rating......................................120 Volts, 60Hz
Separate Circuit..15 amp min......- 20 amp max.
Motor (Amps)............................................1.8
Heater Wattage.........................................900
Total Amps (load rated).............................10.0
TempAssure......................................140
0
F
+
5
0
F
(60
0
C
+
3
0
C) [with outer door in place]
TempBoost........................................145
0
F
+
5
0
F
(63
0
C
+
3
0
C) Heated Wash/Heated Rinse
Sanitize.............................150
0
F
+
5
0
F (66
0
C
+
3
0
C)
Hi-Limit Thermostat .......................200
0
F
(93
0
C)
Water Supply
Suggested minimum incoming water
temperature...........................120
0
F (49
0
C)
Pressure (PSI) min./max...................20/120
Connection..............................3/8” NPT or
3/4” Hose Thread Fitting
Consumption (Normal Cycle).......................
4.9 - 9.7 U.S. gal., 18.5 - 36.7
Water valve fl ow rate (U.S.GPM)..............83
Water recirculation (U.S. GPM)....................
approx. 12
Water fi ll time...................................87 sec.
Symptom
Check the Following
Remedy
Dishwasher will not
operate when turned on.
1. Fuse (blown or tripped).
2. 120 VAC supply wiring
connection faulty.
3. Electronic control board
defective.
4. No 12 VAC power to
control.
5. Motor (inoperative).
6. Door Switch (open
contacts).
7. Door latch not making
contact with door switch
8. Touch pad circuit defective.
9. No indicator lamps
illuminate when START or
OPTIONS are pressed.
1. Replace fuse or reset
breaker.
2. Repair or replace wire
fasteners at dishwasher
junction box.
3. Replace control board.
4. Replace control board.
5. Replace motor/impeller
assembly.
6. Replace latch assembly.
7. Replace latch assembly.
8. Replace console assembly.
9. Replace console assembly.
Motor hums but will not
start or run.
1. Motor (bad bearings).
2. Motor stuck due to
prolonged non-use.
1. Replace motor assembly.
2. Rotate motor impeller.
Motor trips out on
internal thermal
overload protector.
1. Improper voltage.
2. Motor windings shorted.
3. Glass or foreign items in
pump.
1. Check voltage.
2. Replace motor/impeller
assembly.
3. Clean and clear blockage.
Dishwasher runs but will
not heat.
1. Heater element (open).
2. Electronic control board
defective.
3. Wiring or terminal
defective.
4. Hi-Limit thermostat
defective.
5. Thermistor failure.
1. Replace heater element.
2. Replace control board.
3. Repair or replace.
4. Replace thermostat.
5. Replace turbidity sensor.
Detergent cover will not
latch or open.
1. Latch mechanism defective.
2. Electronic control board
defective.
3. Wiring or terminal
defective.
4. Broken spring (s).
5. Defective actuator.
1. Replace dispenser.
2. Replace control board.
3. Repair or replace.
4. Replace dispenser.
5. Replace dispenser.
Dishwasher will not
pump out.
1. Drain restricted.
2. Electronic control board
defective.
3. Defective drain pump.
4. Blocked impeller.
5. Open windings.
6. Wiring or terminal
defective.
1. Clear restrictions.
2. Replace control board.
3. Replace pump.
4. Check for blockage, clear.
5. Replace pump assembly.
6. Repair or replace.
Dishwasher will not fi ll
with water.
1. Water supply turned off.
2. Defective water inlet fi ll
valve.
3. Check fi ll valve screen for
obstructions.
4. Defective fl oat switch.
5. Electronic control board
defective.
6. Wiring or terminal
defective.
7. Float stuck in “UP” position.
1. Turn water supply on.
2. Replace water inlet fi ll
valve.
3. Disassemble and clean
screen.
4. Repair or replace.
5. Replace control board.
6. Repair or replace.
7. Clean fl oat.
Dishwasher water
siphons out.
1. Drain hose (high) loop too
low.
2. Drain line connected to a
fl oor drain not vented.
1. Repair to proper 32-inch
minimum height.
2. Connect to a vented drain.
Detergent left in
dispenser.
1. Detergent allowed to stand
too long in dispenser.
2. Dispenser wet when
detergent was added.
3. Detergent cover held closed
or blocked by large dishes.
4. Improper incoming water
temperature to properly
dissolve detergent.
5. See “Detergent cover will
not open”.
1. Instruct customer/user
2. Instruct customer/user
3. Instruct customer/user
on proper loading of
dishes.
4. Incoming water
temperature of 120
0
F
is required to properly
dissolve dishwashing
detergents.
EXPLODED VIEW OF WASH SYSTEM
Short Turn
Line up the center mark on the back of the
seal with the tub top center and press it
into the channel. Move along the channel
left and right periodically pressing the seal
into place without bunching or stretching
it until going around the corners at the
top. Next, place the free ends into the
channel at the bottom left and right by
creating a short turn at the bottom of the
tub channel and ensuring the seal extends
to the locator ridge at the bottom of the
tub (see enlarged portion of the attached
image). Then, press the seal periodically
into place. Finally slide your fi ngers over
the seal to press it fully in place. When
complete a single face of the seal should
be visible and fl ush with the edge of the
channel.
Always disconnect the dishwasher from the electrical power source before adjusting or
replacing components.
Personal Injury Hazard
WARNING
-
-
-
Electrical
The drain hose must have a loop at
a minimum height of 32 inches
in order to insure proper drainage.
To remove the main circulation
(circ) pump do the following in
sequence: Shut off electricity to the
dishwasher. Disconnect the wiring
harness connections located at the
circ pump’s motor. Remove the two
screws that hold the motor bracket.
Slide the motor bracket away from
the sump. The motor and pump,
now held only by friction against
O-rings, can be pulled out of the
sump.
The assembly is driven by a
synchronous motor. Rotation is in the
counterclockwise direction at 2900RPM.
The motor drives a pump which
supplies 100 percent fi ltered water at
a rate of approximately 10.5 (40LMP)
GPM to one spray arm at a time. The
spray arm’s operation is alternated by
small “pauses” of the motor during the
wash cycle.
Draining is accomplished by using a
small separate synchronous drain pump
mounted to the side of the sump. The
drain check valve is located at the
discharge end of the drain pump. The
drain hose is attached by a worm gear
clamp to the discharge end of the drain
pump.
900 Watt Heater
Refer to the cycle chart on the reverse
side to determine when the heater is
on during the wash cycle. The heater
cycles ON and OFF for brief periods
during the drying cycle.
Voltage checks of the heater
should be made in the dry portion
of the service test mode.
-
-
-
liters
  • Page 1 1
  • Page 2 2

Frigidaire 1135244 Installation guide

1135244
Frigidaire
Brand
Frigidaire
Model
1135244
Category
Dishwashers
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents