Eye Lighting Turbo User manual

Brand: Eye Lighting

Model: Turbo

Type: User manual

Eye Lighting Turbo, a high-performance LED lighting solution, offers unparalleled illumination for various applications. Engineered to withstand harsh environments, it features an IP66-rated remote driver box, ensuring durability and protection against dust and water. With its 3-phase high voltage input, this versatile device provides efficient power distribution for large-scale lighting projects. The Turbo's advanced dimming capabilities, including 3-in-1 dimming and DALI dimming, allow for precise light control and energy savings.

For the latest product information visit the EYE Lighting Australia website

EYE Lighting Australia Pty Ltd

15 Industrial Avenue

Wacol QLD 4076

Email: [email protected]

www.eyelighting.com.au

Tel: +61 (0) 7 3335 3555

Fax: +61 (0) 7 3335 3533

TURBO 3PHASE 22.07.22

Standard

Electrical Wiring of the Remote Driver Box

TURBO Remote Driver Box (3-Phase)

Installation Instructions

CLASSIIP66

Remote driver box weight: 7.5 Kg Max.

Other Possible 3-Phase AC Input Wiring Congurations:

Standard 3-Phase AC Input Wiring Conguration:

NOTE: The wiring congurations depend on site existing 3-Phase wiring

- Isolate & insulate the L1 (Phase1-Red) & Neutral (N-Black) separately

LED

Open remote driver box: 6× M6 screws (5 Nm torque).

AC Input: ex round cable 5 × 1.5 mm2 or 5 × 2.5 mm2

(Ø10-14mm).

Connect L1 , , L3 terminals (isolate & insulate L2 & Neutral

separately) 277 - 480 Vac 50/60 Hz (for 3-Phase 415 V AC input

& high voltage input LED driver).

DC Input: ex round cable 3× 1.5 mm2 or 3× 2.5 mm2 (Ø9-12mm).

Connect V+, ,V- terminals.

Note: This Vdc output is not xed (90/103/105/112/135) for dierent

wattage variants.

Tighten the cable glands and tighten the cover of the remote driver box:

6 × M6 screws (5 Nm).

IP 66 Remote Gearbox

3Nm

WAGO

SPD

LED Driver

SPD

L1 L3

Standard

Standard DC Output Wiring Conguration:

Option

- Isolate & insulate the L3 (Phase3-Blue) & Neutral (N-Black) separately

- Isolate & insulate the L2 (Phase2-White) & Neutral (N-Black) separately

L1 = Live (Phase1) = Red

= GND = Green / Yellow

L3 = Live (Phase3) = Blue

L2 = Live (Phase2) = White

= GND = Green / Yellow

L3 = Live (Phase3) = Blue

V- = Negative DC Output = Black

= GND = Green / Yellow

V+ = Positive DC Output = Red

L1 = Live (Phase1) = Red

= GND = Green / Yellow

L2 = Live (Phase2) = White

3-Phase AC Input: Ø10 - 14mm 1.5 ~ 2.5mm2

5-Core or 4-Core Power Cable

DC Output: Ø9 - 12mm 1.5mm2

3-Core Power Cable

Dimming Wire / OTP Control

Cable Inlet

3-Phase High Voltage Input Connection (refer to exact label for correct termination)

Scan for

PDF Version

From

3-Phase

Power

Source

To the

Junction

Box at

rear of

Turbo

LED

Fixture

IP 66 Remote Gearbox

3Nm

WAGO

SPD

LED Driver

SPD

L1 L3

LED DRIVER

3 in 1

Dimming

or DALI

Dimming

Connections

+5 Nm

Important-Safety

This luminaire and remote driver box must be installed by a licensed electrician, following these installation instructions. Before carrying out any installation

or maintenance on this luminaire, ensure that the mains supply is fully isolated. High voltages greater than mains voltage can be present during operation.

Any inadequate installation might cause falling, electric shock, re, or other hazards. Ensure only qualied personnel inspect and maintains the luminaire.

Excessive build-up of foreign material from outer surfaces should be cleaned to maintain the performance of the luminaire. Do not modify the luminaire,

disassemble or replace any component without conrming with supplier rst. Do not touch the power supply when the luminaire is operating.

For the latest product information visit the EYE Lighting Australia website

EYE Lighting Australia Pty Ltd

15 Industrial Avenue

Wacol QLD 4076

Email: [email protected]

www.eyelighting.com.au

Tel: +61 (0) 7 3335 3555

Fax: +61 (0) 7 3335 3533

TURBO 3PHASE 22.07.22

TURBO LED

FIXTURE