Troy-Bilt TBE304 Driveway Edger Owner's manual

Troy-Bilt
Brand
Troy-Bilt
Model
TBE304 Driveway Edger
Type
Owner's manual

This manual is also suitable for

Troy-Bilt TROY-BILT TBE304 Driveway Edger is a powerful tool designed to help you maintain your driveway and garden edges with ease. With its sturdy construction and reliable engine, this edger delivers precise and efficient cutting performance, ensuring clean and defined borders for your landscaping. The adjustable cutting depth and angle allow you to customize the edging according to your needs, while the ergonomic handlebar and controls provide comfortable operation.

Troy-Bilt TROY-BILT TBE304 Driveway Edger is a powerful tool designed to help you maintain your driveway and garden edges with ease. With its sturdy construction and reliable engine, this edger delivers precise and efficient cutting performance, ensuring clean and defined borders for your landscaping. The adjustable cutting depth and angle allow you to customize the edging according to your needs, while the ergonomic handlebar and controls provide comfortable operation.

IMPORTANT: READ THE OPERATOR’S MANUAL THOROUGHLY AND FOLLOW
THE SAFE OPERATION PRACTICES WHILE OPERATING THE UNIT. Lea la traducción en Español en el manual.
NEED HELP? CALL 1-800-828-5500
Knobs
Handlebar
ASSEMBLY TOOLS REQUIRED
• Wire cutters
Unscrew the oil fill plug. Pour the
entire container of oil into the oil fill
hole. Reinstall the oil fill plug.
NOTE: DO NOT overfill. Never
add oil to the fuel tank. DO NOT
mix oil with gasoline.
Slowly remove the fuel cap. Fill
the fuel tank. Reinstall the fuel
cap. Move the unit at least 30 ft.
(9.1 m) from the fuel container
and the fueling site before
starting the engine.
NOTE: Use fresh unleaded
gasoline (less than 30 days old).
10
11
Read the operator’s manual
thoroughly before operating
the unit. Follow all warnings and
safety instructions. This fast
guide is intended as a reference
for users that have already read
the operator's manual and are
familiar with the necessary safety
precautions.
Align the holes on the upper
shaft with the holes on the
middle shaft. Insert a bolt into
each of the aligned holes. Install
a washer onto each bolt. Install a
knob onto each bolt. Tighten the
knobs securely.
Pull the starter rope and run it
through the eye hook.
Position the upper shaft onto the
middle shaft. Make sure the “V”
bend in the handle is pointing up
(toward the front of the unit) and
that the throttle control is on the
right side when the operater is
standing in the operating
position.
1
6
4 5
Slide the middle shaft onto the
lower shafts.
NOTE: Keep the throttle cable
and wire assembly to the front of
the unit.
Align the holes on the middle
shaft with the holes on the lower
shafts. Insert a bolt into each of
the aligned holes. Install a
washer onto each bolt. Install a
knob onto each bolt. Tighten the
knobs securely.
2 3
ASSEMBLY
Oil Fill Plug
Fuel Cap
Middle Shaft
Lower Shaft
Upper Shaft
Repeat steps 7 - 8 with the hole
on the upper shaft.
NOTE: DO NOT run the throttle
cable and wire assembly through
the eye hook.
NOTE: DO NOT bend or pinch
the throttle cable or wire
assembly.
9
Insert a zip tie into the hole on
the lower shaft.
Loop the zip tie around the
throttle cable and wire assembly.
Secure the zip tie, but do not
tighten it completely. Leave a
small loop.
Use wire cutters to trim excess
zip tie material.
7 8
778-19321 / 00 07/21
Eye Hook
IMPORTANT: READ THE OPERATOR’S MANUAL THOROUGHLY AND FOLLOW
THE SAFE OPERATION PRACTICES WHILE OPERATING THE UNIT. Lea la traducción en Español en el manual.
NEED HELP? CALL 1-800-828-5500
Starter Rope Grip
Primer Bulb
Handlebar
Read the operator’s manual
thoroughly before operating
the unit. Follow all warnings and
safety instructions. This fast
guide is intended as a reference
for users that have already read
the operator's manual and are
familiar with the necessary safety
precautions.
1
Throttle Control
On/Off Switch
PRIME:
Stand in the starting position.
Hold the handlebar firmly with
one hand. Hold the starter rope
with the other hand.
Tilt the unit back slightly to bring
the blade off the ground.
PRIME:
Squeeze and hold the throttle
control.
NOTE: Continue to SQUEEZE
and HOLD the throttle control
for ALL further steps.
45
PRIME:
Slowly press and release the
primer bulb 10 times, or until
fuel is visible.
2
STARTING PRIME:
Move the choke lever to
Position 1.
3
DIDN’T START?
Repeat the starting
instructions.
If the unit still fails to start,
refer to the operator’s
manual for additional
starting and troubleshooting
information.
PRIME:
Pull the starter rope with a
controlled and steady motion 5
times.
DO NOT pull the starter rope
more than 5 times.
START:
Move the choke lever to
Position 2.
START:
Pull the starter rope with a
controlled and steady motion 5
to 10 times to start the engine.
Allow the engine to warm up for
60 seconds.
678
START:
Move the choke lever to
Position 3.
Allow the engine to warm up for
an additional 60 seconds. The
unit may be used during this time.
9
Choke Lever
778-19321 / 00 07/21
  • Page 1 1
  • Page 2 2

Troy-Bilt TBE304 Driveway Edger Owner's manual

Troy-Bilt
Brand
Troy-Bilt
Model
TBE304 Driveway Edger
Type
Owner's manual
This manual is also suitable for

Troy-Bilt TROY-BILT TBE304 Driveway Edger is a powerful tool designed to help you maintain your driveway and garden edges with ease. With its sturdy construction and reliable engine, this edger delivers precise and efficient cutting performance, ensuring clean and defined borders for your landscaping. The adjustable cutting depth and angle allow you to customize the edging according to your needs, while the ergonomic handlebar and controls provide comfortable operation.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents