Furinno 19155 User manual

Type
User manual

This manual is also suitable for

1915520210810
18
Recommended Maximum Weight
*Unit in Pound(lbs.)
WARNING:
>This unit has been designed to
support the maximum loads shown.
Exceeding these load limits could
cause sagging, instability, product
collapse, and/or serious injury.
>DO NOT allow children to climb on
unit.
> Put heavier items on lower shelves.
Assembly Instruction
Customer Support
www.furinno.com
NEED HELP? For replacement requests or product inquiries,
please contact our Customer Service Team by emailing us at
[email protected]. Thank you for selecting Furinno!
20
Recomm. 2 Persons
Approx. 1.5 Hours
Wall stud
wallboard
STEP 11
STEP 12
15
WALL MOUTING SET
12
1 SET
TOOL REQUIRED
Furinno Lucca Simple Design 4-Drawer Dresser
MODEL : 19155
Tool RequiredTool Required
TOOL REQUIRED
2
EXPLODED VIEW
USEFUL HINTS BEFORE YOU START:
1. Read each step carefully before starting.
2. It is important that each step is performed in correct order to avoid difficulties.
3. Identify, soft and count the parts before assembly.
4. Assemble your furniture on packaging cardboard to prevent scratch or damage.
5. Clean the product with mild cleanser using soft damped cloth. Do not use harsh or abrasive cleanser.
6. Using incompatible hardware might cause damage to product.
EXPLODED VIEW
PARTS LIST
LEFT PANEL 1 PC
A
RIGHT PANEL 1 PC
B
HARDWARE LIST
DRAWER SLIDE
6
9
POWER PIN 18 PCS
BOTTOM PANEL 1 PC BOTTOM BACK PANEL 1 PC
E
DRAWER SIDE 8 PCS
G
L BRACKET 4 PCS
7
STEP 9
STEP 10
TOP PANEL 1 PC
C
DRAWER FRONT 4 PCS
F
DRAWER BACK 4 PCS
I
DRAWER BOTTOM 4 PCS
H
SUPPORT PANEL 1 PC
J
10
5
8
PAN HEAD SCREW 46 PCS
HANDLE SCREW 8 PCS
11
DRAWER BRACKET 8 PCS
4 SETS
4
FLAT HEAD SCREW 24 PCS DRADWER SLIDE 4 SETS
TOOL REQUIRED
D
UPPER BACK PANEL 1 PC
L
K
DRAWER SUPPORT 4 PCS
KICK PANEL 1 PC
M
F
E
A
B
C
DH
J
K
L
M
G
G
I
1
4
7
CAM BOLT 12 PCS
FLAT HEAD SCREW 48 PCS
DRIVE FASTENER 16 PCS
13
HANDLE KNOB 8 PCS
3
DOWEL 24 PCS
2
CAM LOCK 12 PCS
WALL MOUTING SET
12
1 SET
hed urface
x4
H
F
7
7
7
7
I
G
G
M
x4
F
H
8
8
13
I
G
G
13
x4
F
G
I
M
4
4
4
4
4
4
8
HANDLE SCREW 8 PCS
DRIVE FASTENER 16 PCS
7
13
HANDLE KNOB 8 PCS
TOOL REQUIRED
TOOL REQUIRED
STEP 9.1 STEP 9.2
DR
DL
CR
CL
CL
CR
10 (DL & DR)
DL
DL
DL
DR
DR
screw position
DR
DL
DR
DL
6
STEP 7
STEP 8
3
STEP 1
STEP 2
1
CAM BOLT 8 PCS CAM LOCK 4 PCS
24
FLAT HEAD SCREW 24 PCS
PAN HEAD SCREW 16 PCS
5TOOL REQUIRED
2
3
2
3
3
3
3
E
J
2
2
2
2
3
2
2
5
5
9
K
D
x4
M
3
3
ed edge
1
2
3
11
2
1
A
CL
3
2
1
ed edge
11
1
2
B
CR
bracket or e ta o brac a
x4
x4
5
5
5
5
11 11
GG
5
Plea e ote, you w repeat t tep for
aw
x4
F
5
5
5
MG
G
PAN HEAD SCREW 16 PCS
5
DRAWER BRACKET 8 PCS
11 TOOL REQUIRED
L BRACKET 4 PCS
3
DOWEL 22 PCS
CAM LOCK 8 PCS
2
5
PAN HEAD SCREW 8 PCS
9TOOL REQUIRED
44
TOOL REQUIRED
3
DOWEL 2 PCS
CR
DRAWER SLIDE 4 SETS
CL
ARROW FACING OUTWARD
ARROW FACING OUTWARD
o
11
5
CR CL
CL
CR
10 (CL & CR)
5
4
STEP 3
STEP 4
STEP 5
STEP 6
TOOL REQUIRED
A
E
A
B
C
Assure that the unit is square.
Distance from corner to corner
must be equal as shown.
and/or serious injury.
Failure to do so could cause instability, product collapse,
All nails must be driven into the parts straight and centered.
Please make sure that the Back Panel is attached securely.
6
5
E
D
B
L
1
2
TURN 180°
TOOL REQUIRED
STEP 5.2
1
2
TURN 180°
TOOL REQUIRED
TURN 180°
TOOL REQUIRED
TOOL REQUIRED
5
PAN HEAD SCREW 6 PCS
6
POWER PIN 18 PCS
A
J
E
D
K
A
B
J
E
D
K
1
2
TURN 180°
STEP 4.1
nished edge
nished edge
STEP 4.2
1
1
1
1
unfinished edge
STEP 5.1
C
nished edge
nished edge
1
CAM BOLT 4 PCS
TURN 90°
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Furinno 19155 User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI