havit HV3270T-BLK-12V Installation guide

HV3270T-BLK-12V
havit
Brand
havit
Model
HV3270T-BLK-12V
Type
Installation guide

The havit HV3270T-BLK-12V is a versatile low-voltage lighting solution suitable for various indoor and outdoor applications. Its sleek black aluminium body and IP54 rating make it resistant to dust and water, ensuring durability in different environments. With its built-in 3.5W LED and adjustable color temperature ranging from warm to cool white, it provides customizable lighting options to suit different moods and preferences.

The havit HV3270T-BLK-12V is a versatile low-voltage lighting solution suitable for various indoor and outdoor applications. Its sleek black aluminium body and IP54 rating make it resistant to dust and water, ensuring durability in different environments. With its built-in 3.5W LED and adjustable color temperature ranging from warm to cool white, it provides customizable lighting options to suit different moods and preferences.

Product Specications
Model No. HV3270T-BLK-12V HV3270T-SLV-12V HV3270T-WHT-12V HV3271T-BLK-12V HV3271T-SLV-12V HV3271T-WHT-12V HV3272T-BLK-12V HV3272T-SLV-12V HV3272T-WHT-12V
Name Taso
Material Aluminium
Colour Black Silver White Black Silver White Black Silver White
IP Rating IP54
Input Voltage 12v DC
Protection Class (Low Voltage)
Lamp Base Built in LED
Lamp Wattage 1x 3.5w 1x 6w 1x 10w
Colour Temp TRI Colour - 3000k, 4000k, 5500k
Lumens 180lm, 190lm, 200lm 350lm, 360lm, 370lm 600lm, 625lm, 650lm
CRI > 80
Wiring Parallel
Dimmable No
Warranty 3 Years Replacement*
HV3270 Dimensions HV3272 DimensionsHV3271 Dimensions
HV3270Mounting Base HV3272 Mounting BaseHV3271 Mounting Base
Contact Details: Warranty Terms & Conditions* Additional Information
Taso Step Light Installation Instructions
143 Beauchamp Road
Matraville NSW 2036
Australia
Tel: 02 9381 8300
Fax: 02 9666 8881
Email: [email protected]
Web: www.havit.com.au
Important Safety Issues:
• This product must be installed by a qualied electrician according to AS/NZS 3000.
• Ensure all electrical mains are disconnected before any installation.
• Modication of this product will void any warranty.
• Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
• When installing low voltage ttings, Voltage to tting must be within +or- 5% of voltage required and cannot be installed more than 25m from LED Driver, if not within this allowance warranty will be voided.
• Aluminium and 304SS ttings must not be installed within 5km of any salt water environments.
• All o-rings and seals must be in place correctly to maintain warranty.
• These instructions may be updated at any time due to product improvements, Please visit website for most current installation instructions.
Must be installed by a licensed electrician
Steps for Installation:
1. Make sure that the electrical circuit is free of voltage (master switch o)
2. Loosen allen screws on side of tting and remove face and set aside.
3. Using an appropriate 12v DC LED Driver - DO NOT CONNECT LIGHT FITTING DIRECTLY TO 240V
4. Strip back the cable on both tting and cable run and twist the positive cables together. Then connect neutral cables together
5. Solder all joins using solder and either a heat gun or butane gas torch.
6. Cover connections using an adhesive lined heat shrink or gel cap to make connection watertight. Failure to do this will void warranty.
7. Heat the heat shrink or crimp the gel cap making sure all connections are covered.
8. Install base plate to wall in desired location, Seal all holes including Cable entry and mounting screws.
9. Fitting is preset to 3000k, To change colour temperature slide switch located on top of PCB to desired colour temperature.
10. Reattach face to base plate making sure allen screws are tight to avoid water penetration
11. Apply silicon around edge of tting to prevent any water from getting inside to electrical connections.
12. All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.
123
22 20
2x Ø5
Ø13
49
83
14
4
10
Mounting Bracket
123
164
22 20
2x Ø5
Ø13
54
124
14
4
10
Mounting Bracket
164
235
15
2x Ø5
Ø13
74
14
4
10
21
10
92
55 92
  • Page 1 1

havit HV3270T-BLK-12V Installation guide

HV3270T-BLK-12V
havit
Brand
havit
Model
HV3270T-BLK-12V
Type
Installation guide

The havit HV3270T-BLK-12V is a versatile low-voltage lighting solution suitable for various indoor and outdoor applications. Its sleek black aluminium body and IP54 rating make it resistant to dust and water, ensuring durability in different environments. With its built-in 3.5W LED and adjustable color temperature ranging from warm to cool white, it provides customizable lighting options to suit different moods and preferences.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents