2. Home
  3. Domestic appliances
  4. Small kitchen appliances
  5. Barbecues & grills
  6. Masterbuilt
  7. CGP24G1D

Masterbuilt CGP24G1D User manual

  • Hello! I've reviewed the user manual for the MASTERBUILT Gravity Fed CGP24G1D grill. This document provides detailed instructions for disassembling and reassembling all parts of the grill, from removing the manifold support bracket and front folding shelf to the hopper, legs and lid, and putting them back together, as well as safety guidelines. I'm ready to answer your questions about the grill and the provided instructions.
  • What should I do before servicing my grill?
    What should I make sure of before working with the grill?
    What should I be aware of when handling the parts?
Gravity Fed Grill CGP24G1D
Grill Body Instruction Sheet
• Always remove plug from outlet before servicing your grill.
• Make sure your grill has fully cooled to avoid burns.
• Some components may have sharp edges. Use caution to avoid injury.
CAUTION
9804190243 210730-GH
Remove: grates/griddle, warming racks, manifold, charcoal from hopper, ash grate, ash can,
grease tray, slides, hopper ash door, any other accessories on the grill.
Disassembly
2
1
Remove the manifold support bracket (2 screws) Remove front folding shelf (4 screws)
2 SCREWS
4 SCREWS
Remove shroud (7 screws) Remove shroud (7 screws)
8
7
Unplug wires from the controller. Remove side shelf (4 screws)
3
Remove hopper lid (2 screws) Remove hopper latch (4 screws)
6
5
Disassembly
4
4 SCREWS
2 SCREWS
2
SCREWS
2
SCREWS
3
SCREWS
4
SCREWS
3
SCREWS
4 SCREWS
Turn the grill upside down on the lid.
13 14
Remove 6 screws from the legs.
Pull the hopper wires through the leg brace hole.
11 12
Remove hopper (6 screws). Pull the hopper off
the body and set to the side.
Remove shroud (7 screws)
910
Unplug the wiring harness.
Disassembly
2
SCREWS
2
SCREWS
3
SCREWS
4 SCREWS
2 SCREWS
6
SCREWS
Disassembly
Remove 6 screws from the legs.
15 16
Take the legs off the body.
Remove 2 bolts that hold the lid to the body.
17 18
Remove the body from the lid.
Assembly
1. Screw the lid onto the body (see step 18).
2. Screw in the leg assembly to the new grill body (see steps 14 and 15).
3. Screw in the hopper to the grill’s body using six (6) screws (see step 12).
4. Plug the wiring together (see steps 10 and 11).
5. Screw in the heat shield to the hopper using twenty one (21) screws (see steps 7,8, and 9).
5. Attach the hopper lid and latch using six screws (6) (see steps 5 and 6).
7. Attach the side shelf using four screws (4) (see step 4).
8. Plug in wires to the controller (see step 3).
9. Attach the front folding shelf using 4 screws (4) (see step 2).
10. Replace the manifold support bracket using 2 screws (2) (see step 1).
11. Replace: grates/griddle, warming racks, manifold, charcoal from hopper, ash grate, ash can, grease tray,
slides, hopper ash door, any other accessories on the grill.
@masterbuilt masterbuilt.com
Customer Service: masterbuilt.com/contact-us • masterbuilt.com/warranty • masterbuilt.com/collections/parts
3
SCREWS 3
SCREWS
2
BOLTS
/