MSI MS-6382 User manual

Brand: MSI

Model: MS-6382

Category: Motherboards

Type: User manual

This manual is also suitable for

msi micro atx mainboard

Version 2.0

G52-MA00563

MS-6382 (v2.X) Micro ATX Mainboard

MSI

MICRO-STAR INTERNATIONAL

Micro-Star International MS-6382

Tested to comply

with FCC Standard

For Home or Office Use

Manual Rev: 2.0

Release Date: March 2002

FCC-B Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a class

B digital device, pursuant to part 15 of the FCC rules. These limits are designed

to provide reasonable protection against harmful interference when the equip-

ment is operated in a commercial environment. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in accor-

dance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to

cause harmful interference, in which case the user will be required to correct

the interference at his own expense.

Notice 1

The changes or modifications not expressly approved by the party respon-

sible for compliance could void the users authority to operate the equipment.

Notice 2

Shielded interface cables and A.C. power cord, if any, must be used in order to

comply with the emission limits.

VOIR LA NOTICE DINSTALLATION AVANT DE RACCORDER AU

RESEAU.

iii

Edition

March 2002

The material in this document is the intellectual property of MICRO-STAR

INTERNATIONAL. We take every care in the preparation of this document,

but no guarantee is given as to the correctness of its contents. Our products

are under continual improvement and we reserve the right to make changes

without notice.

Trademarks

All trademarks are the properties of their respective owners.

Intel

and Pentium

are registered trademarks of Intel Corporation.

PS/2 and OS

/2 are registered trademarks of International Business Machines

Corporation.

Windows

95/98/2000/NT/XP are registered trademarks of Microsoft

Corporation.

Netware

is a registered trademark of Novell, Inc.

Award

is a registered trademark of Phoenix Technologies Ltd.

AMI

is a registered trademark of American Megatrends Inc.

Revision History

Revision Revision History Date

2.0 First Release for PCB 2.X March 2002

Safety Instructions

1. Read the safety instructions carefully.

2. Save this Users Guide for possible use later.

3. Keep this equipment away from humidity.

4. Lay this equipment on a stable and flat surface before setting it up.

5. The openings on the enclosure are used for air convection and to prevent

the equipment from overheating. Note: Do not cover the openings.

6. Make sure that the power voltage is within its safety range and has been

adjusted properly to the value of 110/220V before connecting the equip-

ment to the power inlet.

7. Place the power cord in a way that people are unlikely to step on it. Do not

place anything on the power cord.

8. Always unplug the power cord before inserting any add-on card or module.

9. All cautions and warnings on the equipment should be noted.

10. Never pour any liquid into the opening that could damage the equipment

or cause an electrical shock.

11. If any of the following situations arises, get the equipment checked by a

service personnel:

l the power cord or plug is damaged

l liquid has penetrated into the equipment

l the equipment has been exposed to moisture

l the equipment has not work well or you can not get it work according

to Users Guide

l the equipment was dropped and damaged

l the equipment has obvious signs of breakage

12. Do not leave the equipment in an unconditioned environment with a stor-

age temperature of 60

C (140

F) or above, which may damage the

equipment.

CAUTION: To prevent explosion caused by improper battery

replacement, use the same or equivalent type of battery recommended

by the manufacturer only.

CONTENTS

Chapter 1. Getting Started ........................................................................ 1-1

Mainboard Specification ...................................................................... 1-2

Mainboard Layout ............................................................................... 1-4

Quick Components Guide .................................................................... 1-5

Chapter 2. Hardware Setup ....................................................................... 2-1

Central Processing Unit: CPU .............................................................. 2-2

CPU Installation Procedures ......................................................... 2-2

Thermal Issue for CPU .................................................................. 2-3

CPU Core Speed Derivation Procedure ......................................... 2-3

Memory ................................................................................................ 2-4

Introduction to DDR SDRAM ....................................................... 2-4

DDR Module Combination ............................................................ 2-5

Installing DDR Modules ............................................................... 2-5

Power Supply ....................................................................................... 2-6

ATX 20-Pin Power Connector: JWR1 ............................................ 2-6

Back Panel ............................................................................................ 2-7

Mouse Connector ......................................................................... 2-7

Keyboard Connector ..................................................................... 2-8

USB Connectors ............................................................................ 2-8

Serial Port Connectors: COM A & COM B.................................... 2-9

Joystick/Midi Connectors ............................................................. 2-9

Audio Port Connectors ................................................................. 2-9

Parallel Port Connector: LPT1 ...................................................... 2-10

RJ-45 LAN Jack (optional) ........................................................... 2-11

Connectors ......................................................................................... 2-12

Floppy Disk Drive Connector: FDD1........................................... 2-12

Chassis Intrusion Switch Connector: J1 ...................................... 2-12

Hard Disk Connectors: IDE1 & IDE2 ........................................... 2-13

CD-In Connector: CD_IN ............................................................ 2-14

Aux Line-In Connector: AUX_IN ................................................ 2-14

Modem-In Connector: MODEM_IN ........................................... 2-14

Fan Power Connectors: CFAN1/SFAN1 ...................................... 2-15

Power Saving LED Connector: JGL1 ........................................... 2-16

Power Saving Switch Connector: JGS1........................................ 2-17

IrDA Infrared Module Header: FPIR ........................................... 2-17

Front Panel Audio Connector: JAUD1 ........................................ 2-18

Front Panel Connectors: JFP1 & JFP2 ......................................... 2-19

Front USB Connector: USB1 ....................................................... 2-20

Jumpers .............................................................................................. 2-21

Clear CMOS Jumper: JBAT1 ........................................................ 2-21

CPU Clock Frequency Selection: SW1 ........................................ 2-22

Slots ................................................................................................... 2-23

AGP Slot ...................................................................................... 2-23

PCI Slots ...................................................................................... 2-23

CNR (Communication Network Riser) ......................................... 2-23

PCI Interrupt Request Routing .................................................... 2-24

Chapter 3. AWARD® BIOS Setup ............................................................ 3-1

Entering Setup...................................................................................... 3-2

Control Keys ................................................................................. 3-2

Getting Help .................................................................................. 3-3

The Main Menu ................................................................................... 3-4

Standard CMOS Features .................................................................... 3-6

vii

Advanced BIOS Features .................................................................... 3-8

Advanced Chipset Features............................................................... 3-12

Integrated Peripherals ........................................................................ 3-16

Power Management Setup ................................................................. 3-21

PNP/PCI Configurations..................................................................... 3-26

PC Health Status ................................................................................ 3-29

Frequency/Voltage Control ................................................................ 3-30

Load Fail-Safe/Optimized Defaults ..................................................... 3-31

Set Supervisor/User Password ........................................................... 3-32

Glossary .................................................................................................... G-1

Getting Started

1-1

Chapter 1. Getting Started

Getting Started

The MS6382 v2.X Micro-ATX mainboard is a high performance

computer mainboard based on VIA KT266A & VT8233A chipsets. The

KT266A chipset is ideal for high quality and high integration desktop and

notebook AGP/PCI/LPC computer systems based on Socket A processors.

The VT8233A V-Link Client controller is a highly integrated PCI/LPC

controller. It supports three PCI slots of arbitration and decoding for all

integrated functions and LPC bus.

For sophisticated power management, the KT266A chipset provides

independent clock stop control for the SDRAM, PCI buses and Dynamic

CKE control for powering down of the SDRAM. A seperate suspend-well

plane is implemented for the SDRAM control signals for the Suspend-to-

DRAM operation.

TOPICS

Mainboard Specification 1-2

Mainboard Layout 1-4

Quick Components Guide 1-5

Chapter 1

1-2

Mainboard Specification

CPU

Socket 462 (Socket A) for AMD

Duron

/Athlon

processor with 200/

266MHz FSB

Support 600MHz up to 1.5GHz processor

Chipset

VIA

KT266A Chipset

- Support 66MHz V-Link Host interface with peak bandwidth of 266MB/s

- Advanced ECC memory controller supporting PC133/PC100 SDR

SDRAM and PC2100/1600 DDR SDRAM

- Full featured AGP Controller: AGP v2.0 compliant

VIA

VT8233A Chipset

- High bandwidth V-Link client controller

- Integrated faster Ethernet controller

- Direct sound ready AC97 digital audio controller

- Ultra DMA 33/66/100/133 master mode EIDE controller

- Support both ACPI and legacy APM power management

Clock Generator

Cypress CY28341OC rev. D (support 2 DDR DIMM)

Main Memory

Support four memory banks using two 184-pin (100/133MHz) DDR DIMM

Support a maximum memory size of 2GB

Slots

One (Accelerated Graphics Port) AGP slot

One CNR (Communication Network Riser) slot

Three 32-bit Master PCI Bus slots

- 3rd PCI with MEDION specification reserved

Supports 3.3v/5v PCI bus Interface

On-Board IDE

Dual Channel master mode IDE controller on the VIA

VT8233A Chipset

provides IDE HDD/CD-ROM with PIO, Bus Master and Ultra DMA 33/66/

100/133 operation modes

Can connect up to four IDE devices

Getting Started

1-3

Audio

2 channels S/W Audio CODEC, Realtek ALC201A

AC97s digital link controller was integrated in VIA VT8233A

On-Board Peripherals

On-Board Peripherals include:

- 1 floppy port supports 2 FDD with 360K, 720K, 1.2M, 1.44M and 2.

88Mbytes.

- 2 serial ports (COMA + COM B)

- 1 parallel port supports SPP/EPP/ECP mode

- 4 USB ports (2 x Rear / 2x Front)

- 1 Audio/Game port

- 1 optional RJ-45 LAN jack (Reaktek RTL8100BL)

BIOS

The mainboard BIOS provides Plug & Play BIOS which detects the

peripheral devices and expansion cards of the board automatically.

The mainboard provides a Desktop Management Interface (DMI) func-

tion which records your mainboard specifications.

Dimension

M-ATX Form Factor: 9.6 in. x 8.25 in.

Mounting

6 mounting holes

Others

Support STR/STD (S3/S4)

Support PS2/USB KBD/Mouse Wakeup function in S3 mode

PC 2001 Compliance

Support Chassis Intrusion Detection & SIR

Chapter 1

1-4

Mainboard Layout

MS-6382 v2.X Micro ATX Mainboard

AGP Slot

BATT

VIA

KT266A

VT8233A

USB1

JFP1

JFP2

r S

JGS1

SOCKET 462

Winbond

W83697HF

PCI Slot 3

PCI Slot 2

PCI Slot 1

CNR

JGL1

JBAT1

JAUD1

SW1

FPIR

Top : Parallel Port

Bottom:

COM A

COM B

Top : mouse

Bottom: keyboard

Top: LAN Jack

Bottom: USB

ports

CD_IN

MODEM_IN

RTL

8100BL

Codec

CFAN1

SFAN1

AUX_IN

To p :

Game port

Bottom:

Line-Out

Line-In

Mic

ALC201A

Getting Started

1-5

Quick Components Guide

Component Function Reference

JWR1 ATX 20-pin Power Connector See p. 2-6

USB Connectors Connecting to USB devices See p. 2-8

COM A & B Connector Connecting to Serial ports See p. 2-9

Game/Audio Connectors Connecting to Game/Audio devices See p. 2-9

LPT1 Parallel port connector See p. 2-10

RJ-45 LAN Jack Connecting to LAN devices See p. 2-11

FDD1 Floppy disk drive connector See p. 2-12

J1 Chassis intrusion switch See p. 2-12

IDE1~ IDE2 Hard disk connectors See p. 2-13

CD_IN CD-in connector See p. 2-14

AUX_IN Aux line-in connector See p. 2-14

MODEM_IN Modem-in connector See p. 2-14

CFAN1/SFAN1 Fan power connectors See p. 2-15

JGL1 Power Saving LED Connector See p. 2-16

JGS1 Power Saving Switch Connector See p. 2-17

FPIR IrDA infrared module connector See p. 2-17

JAUD1 Front panel audio connector See p. 2-18

JFP1 & JFP2 Front panel connectors See p. 2-19

USB1 Front USB connector See p. 2-20

JBAT1 Clear CMOS jumper See p. 2-21

SW1 CPU FSB jumper See p. 2-22

AGP Slot Connecting to expansion cards See p. 2-23

PCI Slots Connecting to expansion cards See p. 2-23

CNR Slots Connecting to expansion cards See p. 2-23

Hardware Setup

2-1

Chapter 2. Hardware Setup

TOPICS

Central Processing Unit: CPU 2-2

Memory 2-5

Power Supply 2-6

Back Panel 2-7

Connectors 2-12

Jumpers 2-21

Slots 2-23

Hardware Setup

This chapter provides you with the information about hardware setup

procedures. While doing the installation, be careful in holding the components

and follow the installation procedures. For some components, if you install in

the wrong orientation, the components will not work properly.

Use a grounded wrist strap before handling computer components. Static

electricity may damage the components.

Chapter 2

2-2

Central Processing Unit: CPU

1. Pull the lever sideways away

from the socket. Then, raise

the lever up to a 90-degree

angle.

2. Look for the cut edge. The cut

edge should point towards the

lever pivot. The CPU will only

fit in the correct orientation.

3. Hold the CPU down firmly,

and then close the lever to

complete the installation.

CPU Installation Procedures

Overheating will seriously damage the CPU and system,

always make sure the cooling fan can work properly to

protect the CPU from overheating.

WARNING!

The mainboard supports AMD

Duron

/Athlon

processor. The

mainboard uses a CPU socket called Socket-462 for easy CPU installation.

When you are installing the CPU, make sure the CPU has a heat sink and a

cooling fan attached on the top to prevent overheating. If you do not find the

heat sink and cooling fan, contact your dealer to purchase and install them

before turning on the computer.

Open Lever

Cut edge

Sliding

Plate

Lever

Hardware Setup

2-3

Thermal Issue for CPU

As processor technology pushes to faster speeds and higher performance,

thermal management becomes increasingly crucial when building computer

systems. Maintaining the proper thermal environment is key to reliable

operation. As such, the processor must be maintained in the specified thermal

requirements. AMD recommends the use of high performance thermal inter-

face material.

AMD Athlon processor with a speed of 600MHz and above requires LARGER

heatsink and fan. You also need to add thermal grease between the CPU and

heatsink to improve heat dissipation. Then, make sure that the CPU and heatsink

are securely fastened and in good contact with each other. These are needed

to prevent damaging the processor and ensuring reliable operation.

You can check AMDs web site for more information on proper cooling.

CPU Core Speed Derivation Procedure

If CPU Clock = 100MHz

Core/Bus ratio = 7

then CPU core speed = Host Clock x Core/Bus ratio

= 100MHz x 7

= 700MHz

While replacing the CPU, always turn off the ATX

power supply or unplug the power cable of the ATX

power supply from grounded outlet first to ensure the

safety of CPU.

WARNING!

Chapter 2

2-4

Memory

The mainboard provides 2 slots for 184-pin, 2.5V unbuffered DDR DIMM

with 4 memory banks. You can install PC1600 or PC2100 DDR SDRAM mod-

ules on the DDR DIMM slots (DDR 1~2). To operate properly, at least one

DIMM module must be installed.

Note: The DDR DIMM slots DO NOT support PC2700 modules.

Introduction to DDR SDRAM

DDR (Double Data Rate) SDRAM is similar to conventional SDRAM,

but doubles the rate by transferring data twice per cycle. It uses 2.5 volts as

opposed to 3.3 volts used in SDR SDRAM, and requires 184-pin DIMM mod-

ules rather than 168-pin DIMM modules used by SDR SDRAM. Two types of

DDR SDRAM are available at the time of writing: PC1600, PC2100.

The following table shows the clock and peak bandwidth of each type of

DDR SDRAM module:

PC2100 PC1600

(DDR266) (DDR200)

Clock 133MHz 100MHz

Peak

Bandwidth 2133MB/s 1600MB/s

Hardware Setup

2-5

You can install either single sided or double sided 184-pin DDR DIMM

modules into DDR DIMM slots to meet your needs. Different from the SDR

DIMM, the DDR DIMM has only one notch on the center of module. The

number of pins on either side of the breaks are different. The module will only

fit in the right orientation.

You can install memory modules in any combination as follows:

Slot Memory Module Total Memory

Slot 1

(Bank 0 & Bank 1)

64MB, 128MB,

256MB, 512MB, 1GB

64MB~1GB

Slot 2

(Bank 2 & Bank 3)

64MB, 128MB,

256MB, 512MB, 1GB

64MB~1GB

Maximum System Memory Supported

64MB~2GB

DDR Module Combination

Installing DDR Modules

1. The DDR DIMM has only one notch on the center of module. The module

will only fit in the right orientation.

2. Insert the DIMM memory module vertically into the DIMM slot. Then

push it in.

3. The plastic clip at each side of the DIMM slot will automatically close.

Volt

notch

Chapter 2

2-6

Power Supply

ATX 20-Pin Power Connector: JWR1

This connector allows you to connect to an ATX power supply. To

connect to the ATX power supply, make sure the plugs of the power supply is

inserted in the proper orientation and the pins are aligned. Then push down

the power supply firmly into the connector. The power connector supports

instant power on function which means that system will boot up immediately

when the power supply connector is inserted on the board.

The mainboard supports ATX power supply for the power system. Be-

fore inserting the power supply connector, always make sure that all compo-

nents are installed properly to ensure that no damage will be caused.

PIN SIGNAL

11 3.3V

12 -12V

13 GND

14 PS_ON

15 GND

16 GND

17 GND

18 -5V

19 5V

20 5V

PIN SIGNAL

1 3.3V

2 3.3V

3 GND

45V

5 GND

65V

7 GND

8 PW_OK

9 5V_SB

10 12V

JWR1 Pin Definition

JWR1

Hardware Setup

2-7

The Back Panel provides the following connectors:

Back Panel

Mouse Connector

The mainboard provides a standard PS/2

mouse mini DIN connector for

attaching a PS/2

mouse. You can plug a PS/2

mouse directly into this

connector. The connector location and pin assignments are as follows:

Mouse

Keyboard

USB

Parallel

COM A

COM B

L-out L-in MIC

Midi/Joystick

PIN SIGNAL DESCRIPTION

1 Mouse DATA Mouse DATA

2 N C No connection

3 GND Ground

4 VCC +5V

5 Mouse Clock Mouse clock

6 N C No connection

Pin Definition

PS/2 Mouse (6-pin Female)

LAN

(optional)

Chapter 2

2-8

Keyboard Connector

The mainboard provides a standard PS/2

keyboard mini DIN connector

for attaching a PS/2

keyboard. You can plug a PS/2

keyboard directly into

this connector.

USB Connectors

The mainboard provides a UHCI (Universal Host Controller Interface)

Universal Serial Bus root for attaching USB devices such as keyboard, mouse

or other USB-compatible devices. You can plug the USB device directly into

the connector.

USB Ports

1 2 3 4

5 6 7 8

PIN SIGNAL DESCRIPTION

1 VCC +5V

2 -Data 0 Negative Data Channel 0

3 +Data0 Positive Data Channel 0

4 GND Ground

5 VCC +5V

6 -Data 1 Negative Data Channel 1

7 +Data 1 Positive Data Channel 1

8 GND Ground

USB Port Description

PIN SIGNAL DESCRIPTION

1 Keyboard DATA Keyboard DATA

2 NC No connection

3 GND Ground

4 VCC +5V

5 Keyboard Clock Keyboard clock

6 NC No connection

Pin Definition

PS/2 Keyboard (6-pin Female)

Page is loading ...

MSI MS-6382 User manual

Brand: MSI

Model: MS-6382

Category: Motherboards

Type: User manual

This manual is also suitable for

msi micro atx mainboard

Download PDF

report

MSI MS-6382 User manual

This manual is also suitable for

MSI MS-6382 User manual

Related papers

Other documents