Sony KD-32NX200E User manual

Category
CRT TVs
Type
User manual

This manual is also suitable for

R
Trinitron Digital TV
Instruction Manual
Kayttöohje
Styrfunktioner
GB
KD-32NX200E
KD-36NX200E
© 2003 by Sony Corporation
®
FI
SE
4-094-765-11
cover.fm Page 1 Friday, March 7, 2003 8:34 AM
cover.fm Page 2 Friday, March 7, 2003 8:34 AM
1
GB
GBpages1-8.fm Page 1 Tuesday, October 15, 2002 10:23 AM
Safety information
2
This set is to operate on a 220-240V AC
supply only. Take care not to connect too
many appliances to the same power socket
as this could result in fire or electric shock.
For environmental and safety reasons, it is
recommended that the TV set is not left in
standby mode when not in use. Disconnect
from the mains.
Never push objects of any kind into the set
as this could result in a fire or electric shock.
Never spill liquid of any kind on the set. If
any liquid or solid object does fall through,
do not operate the TV. Have it checked
immediately by qualified personnel.
Do not open the cabinet and the rear cover
of the TV. Refer to qualified service
personnel only.
To prevent fire or shock hazard, do not
expose the TV to rain or moisture.
For your own safety, do not touch any part
of the TV, power lead or aerial lead during
lightning storms.
Do not cover the ventilation openings of the
TV. For ventilation, leave a space of at least
10cm all around the set.
Never place the TV in hot, humid or
excessively dusty places. Do not install the
TV where it may be exposed to mechanical
vibrations.
Clean the TV with a soft, lightly dampened
cloth. Do not use benzine, thinner or any
other chemicals to clean the TV. Do not
scratch the TV screen. As a safety
precaution, unplug the TV before cleaning it.
Pull out the power lead by the plug. Do not
pull on the power lead itself.
Take care not to place heavy objects on the
power lead as this could result in damage.
We recommend you wind any excess lead
around the holders provided on the rear of
the TV.
Unplug the power lead before moving the
TV. Avoid uneven surfaces, quick steps or
excessive force. If the set has been dropped
or damaged, have it checked immediately
by qualified service personnel.
Do not cover the ventilation openings of the
TV with items such as curtains or
newspapers etc.
Place the TV on a secure stable stand. Do
not allow children to climb on to it. Do not
place the TV on its side or face up.
Do not place any objects on the TV. To
prevent fire, keep inflammable objects or
naked lights (e.g. candles) away from the TV.
GBpages1-8.fm Page 2 Tuesday, October 15, 2002 10:23 AM
Table of contents
3
Getting started
Checking the accessories supplied ................................................................................................ 4
Inserting batteries into the remote control ..................................................................................... 4
Connecting an aerial and a VCR to the TV..................................................................................... 5
Switching on the TV........................................................................................................................ 5
Automatically tuning the TV ............................................................................................................ 6
Switching between digital and analogue programmes.................................................................... 7
Finding your video channel ............................................................................................................ 7
Basic operation
Overview of the TV buttons............................................................................................................. 8
Overview of the remote control buttons ..........................................................................................9
Viewing a digital text service........................................................................................................... 10
Viewing a traditional text service..................................................................................................... 11
Using the text menu........................................................................................................................ 12
Changing the screen format manually ............................................................................................ 13
Digital features
The Digital Info display.................................................................................................................... 14
The Main menu............................................................................................................................... 15
Favourite Programmes............................................................................................................15
Wallpaper ................................................................................................................................ 16
Parental control....................................................................................................................... 16
Installation............................................................................................................................... 17
Detailed set-up........................................................................................................................ 18
CA Set-up ............................................................................................................................... 19
Personal Information ............................................................................................................... 19
The Channel Index menu................................................................................................................ 20
Searching for digital channels................................................................................................. 20
To store a channel in your favourites list ................................................................................. 20
To select a category of programme......................................................................................... 20
The EPG menu ............................................................................................................................... 21
Searching for digital channels................................................................................................. 21
To select a category of programme......................................................................................... 21
To select a programme for recording or timed display ............................................................ 22
TV menu system
Using the TV menu system............................................................................................................. 23
Picture Adjustment menu................................................................................................................ 23
Sound Adjustment menu ................................................................................................................ 24
Features menu................................................................................................................................ 25
Set Up menu................................................................................................................................... 25
Manual Set Up menu ...................................................................................................................... 26
Manual Programme Preset menu................................................................................................... 27
Further Programme Preset menu...................................................................................................28
Memory Stick operation
Inserting a Memory Stick ................................................................................................................ 29
Removing a Memory Stick.............................................................................................................. 29
The Memory Stick menu................................................................................................................. 29
Memory Stick precautions .............................................................................................................. 32
Connecting Other Equipment to the TV
Connecting equipment to the rear sockets ..................................................................................... 33
Connecting equipment to the front sockets..................................................................................... 35
Using the remote control with VCR and DVD players..................................................................... 36
Additional information
Specifications.................................................................................................................................. 37
Troubleshooting............................................................................................................................... 38
GBpages1-8.fm Page 3 Tuesday, October 15, 2002 10:23 AM
Getting started
4
VIDEO
TV
G
UIDE
0
4
6
7
8
9
1
2
3
5
D
IG
IT
A
L
M
E
M
O
R
Y
STICK
M
O
D
E
INDEX
PROG
MENU
/
/
VT
R
TV
DV
D
Checking the accessories supplied
Batteries
Inserting batteries into the remote control
Always remember to dispose of batteries in an environmentally friendly way
Follow steps - to install your TV and view the TV programmes.
Place a coin in the slot at the bottom of the
remote control. Turn anti clockwise to
release the battery compartment.
Insert the batteries as indicated in
battery compartment.
Replace the battery compartment and lock
in place by twisting the coin clockwise in the
slot.
RF Loopthrough cable
1
2
Modem
1
7
Remote control
1
3
2
GBpages1-8.fm Page 4 Tuesday, October 15, 2002 10:23 AM
Getting started
5
Connecting an aerial and a VCR to the TV
Connecting an aerial and a VCR
Switching on the TV
Connecting an aerial only
3
4
1.
Connect your existing aerial lead to the digital
socket marked on the rear of the TV as
shown.
2.
Connect the supplied RF loopthrough cable from
the socket marked to the analogue socket
marked .
1.
Connect your existing aerial lead to the digital
socket marked on the rear of the TV as shown.
2.
Connect the supplied RF loopthrough cable from
the lower socket marked on the TV to the RF
IN socket on your VCR.
3.
Connect a lead from the RF OUT socket on your
VCR to the analogue socket marked on the TV.
4.
Connect a fully wired scart lead from the
socket on the rear of the TV to the scart
socket on your VCR (refer to your VCR instruction
manual).
5.
Connect the VCR to the mains socket and switch
on.
6.
Insert a pre-recorded tape into the VCR and press
the ‘PLAY’ button. This enables the TV to locate and
store the video channel during the ‘Automatically
tuning the TV’ procedure.
Note:
Your VCR sockets may not be labelled RF IN and RF OUT. If not,
please refer to your VCR instruction manual for guidance.
s
3
3
1.
Connect the TV plug to your mains socket
(220 - 240 V AC, 50 Hz).
2.
Push in the on/off button (labelled ) on the
front of the TV.
Note:
If the red indicator on the front of the TV is lit the TV is in standby
mode. Press the TV button on the remote control to switch on
the TV. Please be patient as the picture may take a few moments to
appear on screen.
/
R/D/D/D
L/G/S/I
ANALOGUE
1
2
DVD
VCR
s
3
3
(SMARTLINK)
DIGITAL
OPTICAL OUTPUT
MODEM
. . .
5V 200mA
Existing
aerial lead
R/D/D/D
L/G/S/I
ANALOGUE
1
2
DVD
VCR
s
3
3
(SMARTLINK)
DIGITAL
OPTICAL OUTPUT
MODEM
. . .
5V 200mA
RF loopthrough
cable (supplied)
RF lead (not
supplied)
Scart lead
(not supplied)
RF loopthrough
lead (supplied)
GBpages1-8.fm Page 5 Tuesday, October 15, 2002 10:23 AM
Getting started
6
PROG
OK
1
4
7
3
6
9
2
5
8
0
5
1.
When you switch on the TV for the first time, the Sony logo appears on the
TV screen followed by the ‘Memory Stick’ logo, then the Language/Country
menu with the word ‘English’ highlighted. Press the V or v buttons on the
remote control to choose the language you require then press the OK
button to confirm.
2.
The word Country is now highlighted. Press the V or v buttons to choose
the country in which you wish to operate the TV, then press the OK button to
confirm.
The picture rotation prompt appears. Sometimes the Earth’s natural
magnetism can cause the screen to look tilted.
a) If no correction is required, press the B button.
b) If some correction is required, press the OK button. Press the V or v
button to rotate the picture over a range of -5 to +5. Press the OK button
to store.
An autotune prompt appears on screen. Press the OK button to select ‘Yes’.
A menu is displayed giving you two options to choose from:
Quick tuning: Tunes in the recommended signals for your location.
Full tuning: Tunes in all the available signals.
Use the V or v buttons to make your choice then press the OK button.
Note:
‘Full tuning’ may take some time to tune in all the available signals. For normal use,
we recommend you use the ‘Quick tuning’ feature.
A display appears asking you to press the OK button to begin tuning. As the
digital tuning procedure may take some time, a menu is displayed to show
you the tuning progress. Please be patient and do not press any buttons
once this search and store operation has started.
When the on screen display informs you that the tuning is successfully
finished, press the BLUE button repeatedly to remove all menus from the
screen. The analogue tuning procedure then begins.
If no digital and no analogue signals are found, a display appears on screen
asking you to confirm your aerial is connected. Check your aerial is
connected then press the OK button to repeat the tuning procedure.
Once all signals have been captured and stored, the TV returns to normal
operation and displays the digital programme captured on programme
number 1.
Note:
If no digital signals are captured, then the analogue programme stored on
programme number 1 is displayed.
3.
To view programmes, press the PROG+/- button or the numbered buttons
on the remote control.
Automatically tuning the TV
GBpages1-8.fm Page 6 Tuesday, October 15, 2002 10:23 AM
Getting started
7
DIG
IT
AL
D
IG
ITA
L
PROG
D
IG
IT
AL
D
IG
IT
AL
1.
Press the DIGITAL/ button on the remote control to switch between
digital and analogue mode.
Notes:
If the TV is in digital mode an information banner appears briefly on screen when you change
channels.
If the TV is in analogue mode the channel number appears in green lettering when you change
channels.
Finding your video channel
7
Switching between digital and analogue programmes
6
If you connected a VCR to your TV when following the ‘Connecting an aerial and a VCR
to the TV’ instructions, you now need to find your video channel.
1.
First ensure the TV is in analogue mode. If not press the DIGITAL/
button on the remote control.
2.
Press the PROG+/- button on the remote control until the picture from the
pre-recorded tape appears on screen.
Notes:
If you wish to move your video channel to a different programme number, refer to the
‘Rearranging your channels’ section of this manual.
If you have connected your VCR using a scart lead, press the
/ button
repeatedly on the remote control until the picture from the pre-recorded tape appears
on the TV screen.
GBpages1-8.fm Page 7 Tuesday, October 15, 2002 10:23 AM
Basic operation
8
MONO
L/G/S/I
R/D/D/D
MEMORY STICK
+
P +
4
S
4
4
Overview of the TV buttons
The TV buttons can be found on the control panel on the front of the TV. An expanded view is shown below.
Programme Up or Down buttons
Press to move to the next or preceding
channel.
Volume control buttons
Press to increase or decrease the volume.
Video input button
Press to select input signals from a
VCR etc.
Reset button
Press to return picture and sound levels
to their factory settings.
Note:
When the ‘Memory Stick’ is reading or
wriiting data, the memory stick indicator
lights up in red. Data stored on a
‘Memory Stick’ may become damaged or
erased if you remove the ‘Memory Stick’
during this time.
GBpages1-8.fm Page 8 Tuesday, October 15, 2002 10:23 AM
Basic operation
9
Overview of the remote control buttons
Mute button
Press to mute the sound. Press again to
restore.
VIDEO
TV
GUIDE
0
4
6
7
8
9
1
2
3
5
D
IG
IT
A
L
MEMORY
STIC
K
M
O
DE
IND
EX
PROG
MENU
/
/
VTR
T
V
D
V
D
VIDEO button
Press to switch off your VCR or DVD temporarily.
Press again to return to normal operation.
/
TV button
Press to switch off your TV temporarily. The red
indicator on the front of the TV illuminates. Press
again to return to normal operation
/
DIGITAL/ button
Press to switch between digital and
analogue mode.
Screen format button
Press repeatedly to change the screen format.
Input button /Hold button
Press to select signals from equipment connected
to the TV sockets (refer to ‘Connecting other
equipment to the TV’).
In text mode press to keep a page on display. Press
again to cancel.
Buttons 0 - 9
Press to input the required channel
number. For numbers 10 and above,
enter the second digit within 2 seconds.
Previous channel button
While watching Analogue TV pressing this button
will return you to the previous channel you were
watching.
While watching Digital TV pressing this button can
also act as an ‘EXIT’ key and cancel any Digital text
application that may be running.
PROG +/- button
Press to select the next or previous programme.
Volume + and - button
Press to adjust the volume to the desired level.
Info button
Press to display the INFO menu in digital mode.
When watching analogue programmes press to
reveal information such as programme number etc.
When in text mode, press to reveal hidden
information such as answers on quiz pages. Press
once more to remove hidden information.
INDEX button
When in digital mode, press to display the Channel
Index menu.
MENU button
Press to enter the menu system of this TV.
MEMORY STICK button
Press to display the Memory Stick menu.
MODE button
This remote control operates not only
Sony DVDs and VCRs, but also those
made by other manufacturers. Press this
button to select the type of equipment
you want to control. A green light appears
momentarily to indicate the mode
selected.
Note:
Before operating your VCR or DVD, you must
enter the correct configuration code. Please
refer to the section ‘Using the remote with
VCR/DVD players’.
GUIDE button
Press to launch digital text or digital
interactive services.
Text button
Press to enter text mode.
EPG button
Press to display the Electronic
Programme Guide when in digital mode.
Coloured buttons
These buttons are used for the text and
digital menus. Refer to the relevant
sections in this instruction manual.
Control pad
Use these buttons to navigate through
the menu system of the TV.
Note:
When the MODE button has been set to VCR
or DVD, the control pad operates the main
functions of your VCR or DVD.
OK button
Press to display a list of channels on screen. Press
the V or v button to scroll through the list until the
channel you wish to view is highlighted, then press
the OK button to display that channel on screen.
GBpages9-13.fm Page 9 Tuesday, October 15, 2002 10:26 AM
Basic operation
10
OK
1
4
7
3
6
9
2
5
8
0
D
IG
ITAL
D
IG
ITAL
Viewing a digital text service
Most digital TV channels broadcast information via their text service. This digital service
includes high quality text and graphics along with advanced navigation options.
Additionally, this TV has access to dedicated text channels transmitted by the
broadcasting authorities. The appearance, content and navigation methods of all digital
text services are decided by the broadcaster. For example, the RTL digital text service
may look different to ZDF’s digital text. However, the digital text services currently
available use simple navigation methods based on the following buttons:
The GUIDE button to display digital text,
The V, v, B and b buttons (to move around the screen),
The OK button or the numbered buttons (to select items on screen),
The four coloured buttons (to access shortcuts).
Selecting a dedicated digital text channel
Selecting a text service from other digital channels
Normal text services may also be available on other digital channels. This is sometimes
indicated by a small symbol on your TV screen, superimposed on the programme you
are watching.
1.
Press the button on the remote control to check if you are in digital
mode. If you are watching a digital programme an Info display appears on
screen providing brief details for the current and next programme. If the
display does not appear, press the DIGITAL/ button to switch to digital
mode.
2.
Press the button to remove the Info display from the TV screen then
select the programme number that is broadcasting the dedicated digital text
channel by using the numbered buttons on the remote control. If you do not
know the channel number of a dedicated digital text channel, you can use the
‘Channel Index menu’ to find one. (Please refer to the ‘Channel index menu’
section of this manual.)
3.
Once the text page is displayed, follow the on-screen instructions to obtain
your required selection.
Note:
On some pages the TV programme may also be displayed on the text screen. On-
screen instructions will inform you how to change the displayed programme.
4.
If you are instructed to press ‘OK’ or ‘Select’ when viewing the text pages,
press the OK button.
5.
When you have finished viewing the text service, press the button to exit.
1.
Press the V, v, B, or b buttons to select the symbol, then press the OK
button to display the chosen information.
2.
Alternatively, you may be instructed to use the numbered or coloured buttons
on your remote control to display the various pages of text information. If you
are instructed to press ‘OK’ or ‘Select’ when viewing the text pages, press
the OK button.
3.
Once the text information is displayed, you can access required information
by using the V, v, B, or b buttons, the coloured buttons and/or the numbered
buttons on the remote control.
4.
When you have finished viewing the text service, press the button to exit.
GBpages9-13.fm Page 10 Tuesday, October 15, 2002 10:26 AM
Basic operation
11
1
4
7
3
6
9
2
5
8
0
D
IG
IT
A
L
D
IG
IT
A
L
OK
PROG
Viewing traditional teletext
Most analogue TV channels broadcast a text service. The index page (usually page
100) provides information on how to use the service. Please ensure you are receiving a
strong signal or some text errors may occur.
Switching on the text service
How to use the text features
1
Select the TV channel that carries the text service you wish to view.
2
Press the button to enter Picture and Text (P&T) mode. The screen is
divided into two with the Text display on the left and the TV channel in the
right corner.
Press the button a second time to enter full screen Text mode.
Press the button a third time to enter Mix mode.
3
Press the numbered buttons to enter a three digit number for the text page
you wish to view. Your selected page appears on screen.
4
Enter more 3 digit page numbers as required.
5
When you have finished viewing the text service, press the DIGITAL/
button to remove the text display from the screen.
Text Features How to select
To select the next or
preceding page
Press the or button.
To select a sub page A text page can consist of several sub pages. In this case
an information box is displayed at the bottom of the screen
showing the number of sub pages available. Select the
sub pages by pressing the V or v button.
To keep a page on
display
Press the button. Press again to cancel.
To use Fastext Fastext allows you to access pages with one button push.
When Fastext is available, four coloured items appear at
the bottom of the screen. Press the corresponding
coloured button on the remote control to display the page.
To use the Page
Catching feature
Select a page that contains several page numbers (e.g.
the index page), then press the OK button. Press the V or
v button to highlight the page number required, then press
the OK button again. Your selected page appears on
screen.
Reveal Press the button to reveal hidden information on the
page (such as answers to a quiz).
GBpages9-13.fm Page 11 Tuesday, October 15, 2002 10:26 AM
Basic operation
12
1
4
7
3
6
9
2
5
8
0
OK
MENU
Viewing traditional teletext
Using the text menu
You can access more features by using the text menu:
1
Press the button on your remote control to enter the conventional text
mode.
2
With the text display on screen, press the MENU button to display the
Te l et ext ’ menu.
3
Press the V or v button to highlight your desired feature, then press the b
button to select.
4
Press the MENU button to remove the ‘Te l etex t ’ menu from the screen.
The following table explains each feature and its function:
Feature Function
Top/Bottom/Full This feature allows you to enlarge sections of the displayed
page. Press the V button to enlarge the upper half of the
page or v to enlarge the bottom half. Press the OK button to
return the page to normal size. Press the B button to return to
the ‘Tele t ex t’ menu.
Text Clear
(not available in
P&T mode)
Use this feature to watch a TV programme when the text
service is searching for a page. Once the page has been
found, a blue symbol appears in the top left corner of the
screen. Press the button to view the page.
Index Most Text services contain an index page which lists all the
available pages and their 3 digit page number. Press the b
button to display the index page on screen.
Page Overview
(Only for TOPText
broadcasts)
TOP-Text pages are divided into two columns. The first
column shows ‘blocks’ of pages and the second shows
‘groups’ of pages. Press the b or B button to select the
desired column, then press V or v button to select the
relevant ‘group’ or ‘block’ of pages. Press the OK button to
display the chosen pages.
Contrast This feature allows you to adjust the contrast setting of Text
pages. Press the b or B button to increase or decrease the
contrast. Press the OK button to confirm.
GBpages9-13.fm Page 12 Tuesday, October 15, 2002 10:26 AM
Basic operation
13
Changing the screen format manually
The broadcaster may transmit programmes in more than one format (e.g. 4:3 format or
Widescreen format). You can change the screen format manually to suit the broadcast
you are watching. Press the button on the remote control to choose one of the 5
formats listed below.
Wide-
For 16:9 broadcasts.
For 4:3 broadcasts.
Zoom-
Imitation of wide screen effect for movies broadcast in cinemascopic (letter
box) format.
14:9-
Compromise between the 4:3 and 16:9 format.
4:3-
Conventional screen format.
Smart-
Imitation of wide screen effect for 4:3 broadcasts.
Note:
In Smart, Zoom and 14:9 modes, parts of the top and bottom of the screen are cut off. Press the V or
v button to adjust the position of the image on screen (e.g. to read subtitles).
GBpages9-13.fm Page 13 Tuesday, October 15, 2002 10:26 AM
Digital features
14
OK
D
IG
IT
A
L
D
IG
IT
A
L
The Digital Info display
This display gives you information both on the current programme being shown and on
future programmes when available from the broadcaster (up to 24 hours ahead).
Using other Info features
Subtitles
This feature places digital subtitles on the screen. With the Digital Info display on screen,
press the RED button to access the ‘Subtitles’ pop-up menu. Press the V or v button to
highlight the language you wish the subtitles to appear in, then press OK to select.
Audio
When a multi language broadcast is available, this feature allows you listen to the
broadcast in your selected language. With the Digital Info display on screen, press the
GREEN button to access the ‘Audio’ pop-up menu. Press the V or v button to highlight
the language required then press OK to select.
Timers
When you highlight a current programme, the ‘Timers’ feature allows you to
automatically set your VCR to record the selected programme (only if you have a
Smartlink VCR), or you can select ‘Wake up’ to have the TV switch to the correct channel
automatically when the programme starts. Press the b button to select a future
programme from the Info display, then press the YELLOW button to display the ‘Timers’
pop-up menu.You can then choose from a) Record b) Wakeup or c) Manual.
a) Record
Highlight ‘Record’ and press OK to automatically set your VCR to record the selected
programme (this will only work if your VCR has SmartLink capability and is connected to
the AV3 socket on the rear of this TV).
b) Wakeup
Highlight ‘Wakeup’ and press OK if you wish the future programme you selected to
appear on-screen when transmission begins.
c) Manual
Highlight ‘Manual’ and press OK if you wish the TV to output a channel to your VCR for
recording. Press the V or v button to set the day of recording, then press the b button to
move to the start time. Repeat this procedure to set the start and stop times and the
channel number, then press the OK button to store and return to the Info menu. Press
the button to remove the Info menu from the screen. Unless you have a Smartlink
VCR, you must now set the timer recording function of your VCR to switch on and off to
correspond with the programme you have stored for recording.
Notes on recording:
The ‘Manual’ feature only works if you have connected your VCR to the AV3 socket
on the rear of the TV.
After you have programmed a recording you can put the TV into its standby mode, but do not switch
off completely or the recording will be cancelled. If you put the TV into standby mode, the standby
indicator on the front of the TV flashes green periodically to remind you a recording has been
programmed. Once a programme has started recording, do not change channels or switch to
analogue mode or the recording will be cancelled.
Set-up
Press to display the Main Menu (see next page).
1.
Press the button on the remote control to view the Info display. If the
display does not appear, press the DIGITAL/ button to switch to digital
mode, then press the button to view the Info display.
2.
Press the b button to obtain a brief description of the next programme in the
schedule. If the programme box is blank, there is no information currently
available. To return to the starting point, press the B button repeatedly until
the description for the current programme reappears.
3.
Press the button on the remote control at any time to exit the Info display.
s
3
3
s
3
3
s
3
3
s
3
3
GBpages14-22.fm Page 14 Tuesday, October 15, 2002 10:28 AM
Digital features
15
OK
D
IG
IT
A
L
D
IG
IT
A
L
The Main Menu
The following pages explain the digital menus and their operation. To check you are in
digital mode, press the DIGITAL/ button on the remote control. An information
banner appears briefly on screen when you change channels. If the banner does not
appear, press the DIGITAL/ button.
Favourite Programmes
Use this option to create a list of your favourite programmes in one of three personal
folders, which can then be accessed using the Electronic Programme Guide (EPG) or
Channel Index feature of this TV.
1.
With the Info display on screen, press the BLUE button on your remote
control to display the Main Menu.
2.
Press the V or v button to highlight ‘Favourite Programmes’ then press the
OK button. A display appears giving you the choice of three personal folders.
3.
Press the V or v button to select the folder you wish to use, then press OK
to display the programme listing for that folder.
4.
Press the V or v buttons to scroll through the list until the programme you
wish to store as a favourite is highlighted, then press the OK button. The √
symbol appears alongside the programme to indicate it is now stored as a
favourite. Repeat this procedure to store other favourite programmes.
To deselect a favourite programme:
Highlight the programme, then press the OK button. The √ symbol disappears
from the TV screen.
To deselect all favourite programmes:
Press the YELLOW button.
To rename a favourite folder:
Press the BLUE button to return to the ‘Favourite Programmes’ display, then
press the V or v button to highlight the folder you wish to rename. Press the
YELLOW button to display an on-screen keyboard. Press the RED button to
clear the existing name, then using the V, v, B and b buttons, select the first
letter you require and press OK. The letter appears in the favourite name box.
Repeat this procedure until the name is complete, then after using the V, v,
B and b buttons to highlight DONE, press OK.
Note: If you make a mistake when renaming the folder, press the GREEN button to
return to the original name.
5.
Press the BLUE button repeatedly to remove all menus from the TV screen.
GBpages14-22.fm Page 15 Tuesday, October 15, 2002 10:28 AM
Digital features
16
OK
OK
1
4
7
3
6
9
2
5
8
0
The Main Menu
Wallpaper
This feature allows you to customise the background pattern for all the digital menus.
Parental Control
This option allows you to set an age limit above which a PIN number is required before
viewing is allowed.
1.
Press the button, then press the BLUE button on the remote control to
display the Main Menu
2.
Press the v button to highlight ‘Wallpaper’ then press the OK button to
confirm.
3.
Press the V or v button to select your choice of wallpaper, then press OK to
store.
4.
Press the BLUE button repeatedly to remove all menus from the TV screen
1.
Press the button, then press the BLUE button on the remote control to
display the Main Menu.
2.
Press the v button to highlight ‘Parental Control’ then press the OK button to
display the Parental Control menu.
3.
Enter your existing PIN code using the buttons 0 - 9 on the remote control.
The PIN code has been preset to 1234, but you can change this as explained
later in the ‘Detailed Set-up’ menu.
4.
The age box now becomes active. Press the V or v button to set the age limit
you desire or set to ‘None’ for unrestricted viewing. Press the OK button to
confirm the setting.
5.
Press the BLUE button repeatedly to remove all menus from the TV screen.
GBpages14-22.fm Page 16 Tuesday, October 15, 2002 10:28 AM
Digital features
17
OK
1
4
7
3
6
9
2
5
8
0
The Main menu
Installation
This option allows you to tune in programmes automatically or manually and to change
the order of the stored programmes.
1.
Press the button, then press the BLUE button on the remote control to
display the Main Menu.
2.
Press the V or v buttons to select ‘Installation’ then press the OK button to
display the Installation menu.
3.
Press the V or v buttons to select your chosen item on the menu screen then
press the OK button to display the relevant sub menu.
Quick Tuning
This option will tune in all the recommended signals for your location.
Full Tuning
This option will tune in all the signals available. As this option may take some
time a menu is displayed showing the tuning progress.
Manual Tuning
With this option you can manually add channels to your TV.
1. With the ‘Manual Tuning’ menu on display, enter the new programme
number for your chosen channel using the buttons 0 - 9. Press the OK
button to confirm.
2. The Manual Tuning programme list is displayed with your chosen
programme number highlighted. Press OK to confirm and display the
Search menu.
3. The search will begin from the channel number shown highlighted. If
you wish to change this to a channel number of your choice, press the V
or v button or enter the number directly using the buttons 0 - 9. Press
the b button to make the ‘Select Search’ box active.
4. Press the V or v button to begin the search process. ‘Searching ...’
appears alongside the word ‘Status’ to indicate searching is taking
place. If no digital services are found on your chosen channel, the
channel number changes up or down automatically and the search
continues. Once all the services allocated to the channel have been
found, they are displayed in the ‘Services Found’ box.
5. Press the V or v button to highlight the service you wish to allocate to
the programme number selected in Step 1, then press the OK button to
return to the Manual Tuning programme list display.
Note:
Manual tuning allows you to add another service from the same channel to a
different programme number. To do this, select a new programme number from
the display using the V or v button, then press the YELLOW button to display the
full service list for the channel. Press the V or v button to select the service you
require on the chosen programme number, then press the OK button to return to
the Manual Tuning programme list display.
6. If you wish to tune in more channels, highlight a new programme
number using the V or v button, then press OK. Repeat steps 3 to 5.
Programme Sorting
Use this option to change the order of the stored channels. With the
‘Programme Sorting’ menu displayed on the screen, press the V or v buttons
to highlight the channel you wish to move then press the YELLOW button.
Use the numbered buttons on your remote control to enter the new
programme number for your chosen channel then press the OK button to
confirm. Repeat this procedure to move other channels.
Once you have made all the changes you require in the Installation menu,
press the BLUE button repeatedly to remove all menus from the TV screen.
GBpages14-22.fm Page 17 Tuesday, October 15, 2002 10:28 AM
Digital features
18
1
4
7
3
6
9
2
5
88
0
OK
The Main Menu
Detailed set-up
Use this option to change your PIN number, modem settings and languages etc.
1.
Press the button, then the BLUE button on the remote control to display the
Main Menu.
2.
Press the V or v button to highlight ‘Detailed Set-up’, then press the OK button
to display the Detailed Set-up menu.
3.
If you wish to change any of the settings on the menu screen, press the V or v
button to select your chosen item then press the OK button to display the
relevant sub menu.
PIN Set-up
This allows you to exercise parental control over programme viewing. Enter
your existing PIN and press OK. Use the numbered buttons on your remote
control to enter your new number, then enter again to confirm. Press the OK
button then the BLUE button to return to the Detailed Set-up menu.
Note:
If you have forgotten your PIN code, please use 9999. This PIN code will always be
accepted.
Modem
This allows you to set up the supplied modem. Press the V or v button to select
your chosen item on the screen then press the OK button to confirm. Press the
V or v button to change the setting then press the OK button to store. Press
the BLUE button to return to the Detailed Set-up menu.
Return Channel
Press the V or v buttons to select your chosen item on the menu screen then
press the OK button to display the keyboard*. Press the RED button to clear any
existing name then, using the V, v, B or b buttons, select the first letter or
number you require. Press the OK button to display the letter or number in the
name box. Repeat the procedure until the name is complete then, after using
the V, v, B or b buttons to highlight DONE, press the OK button. Finally, press
the BLUE button to return to the Detailed Set-up menu.
Note:
If you select ‘Default ISP’ or ‘DNS IP Address’ you need to use the numbered buttons on
your remote control to input your new settings. Once complete, press the OK button to
confirm.
MHP Applications Rights
This allows you to set your preferences and also limit some MHP Applications.
Press the V or v buttons to select your chosen item on the screen, then press
the OK button to confirm. Press the V or v button to change the setting as
desired, then press the OK button to store the new setting. Press the BLUE
button to return to the Detailed Set-up menu.
Languages
Press the V or v button to select the Audio Language you want, then press the
OK button to confirm and store the new setting. Press the BLUE button to return
to the Detailed Set-up menu.
Manufacturer information
This is an information screen only and confirms the signal strength and which
versions of hardware and software are available. Press the BLUE button to
return to the Detailed Set-up menu.
Software Upgrade
This allows the TV to automatically upgrade its software when a new version is
transmitted. Press the V or v buttons to set to ‘Yes’ or ‘No’ then press the OK
button to store. When set to ‘Yes’, any new operating software is automatically
downloaded when released. We recommend this option is set to ‘Yes’.
Factory settings
Press the OK button to select ‘Clear Personal Settings’ (this returns all your
digital settings to their factory pre-set levels).
4.
Once you have made all the changes you require in the Detailed Set-up menu,
press the BLUE button repeatedly to remove all menus from the TV screen.
Note:
The CA Set-up option is explained on the following page.
GBpages14-22.fm Page 18 Tuesday, October 15, 2002 10:28 AM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120

Sony KD-32NX200E User manual

Category
CRT TVs
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI