Please read this manual carefully before operating your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote
this information to your dealer
when you require service.
OWNER’S MANUAL
PLASMA MONITOR
MODELS: 71PY1M
P/NO : 38289U0558C
2 Plasma Monitor
Warning
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to
the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of suffi-
cient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the appli-
ance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
FCC NOTICE
• A Class B digital device
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
• Any changes or modifications not expressly approved by the party responsible for compli-
ance could void the user’s warranty.
CAUTION:
Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized mod-
ification could void the user’s warranty.
COMPLIANCE:
The responsible party for this product’s compliance is:
LG Electronics U.S.A., Inc
1000 Sylvan Avenue, Englewood Cliffs, NJ 07632
1-800-243-0000
http://www.lgusa.com
W
W
arning
arning
Owner’s Manual 3
Safety Instructions
Safety Instructions
Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS
Important safety instructions shall be provided with each apparatus. This information shall be given in a separate booklet
or sheet, or be located before any operating instructions in an instruction for installation for use and supplied with the appa-
ratus.
This information shall be given in a language acceptable to the country where the apparatus is intended to be used.
The important safety instructions shall be entitled “Important Safety Instructions”. The following safety instructions shall be
included where applicable, and, when used, shall be verbatim as follows. Additional safety information may be included by
adding statements after the end of the following safety instruction list. At the manufacturer’s option, a picture or drawing that
illustrates the intent of a specific safety instruction may be placed immediately adjacent to that safety instruction :
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accor-
dance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including ampli-
fiers)that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong, The wide blade or the
third prong are provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for replace-
ment of the obsolete outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11. Only use attachments/accessories specified by the man-
ufacturer.
Owner's Manual
4 Plasma Monitor
Safety Instructions
12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been dam-
aged in any way, such as power-supply cord or plug is dam-
aged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has exposed to rain or moisture,
does not operate normally, or has been dropped.
15. CAUTION concerning the Power Cord :
Most appliances recommend they be placed upon a dedi-
cated circuit; that is, a single outlet circuit which powers only
that appliance and has no additional outlets or branch cir-
cuits. Check the specification page of this owner's manual to
be certain.
Do not overload wall outlets. Overloaded wall outlets, loose
or damaged wall outlets, extension cords, frayed power
cords, or damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric shock or fire.
Periodically examine the cord of your
appliance, and if its appearance indicates damage or deteri-
oration, unplug it, discontinue use of the appliance, and have
the cord replaced with an exact replacement part by an
authorized servicer.
Protect the power cord from physical or mechanical abuse,
such as being twisted, kinked, pinched, closed in a door, or
walked upon. Pay particular attention to plugs, wall outlets,
and the point where the cord exits the appliance.
16. Outdoor Use Marking :
WARNING - To Reduce The Risk Of Fire Or Electric Shock,
Do Not Expose This Appliance To Rain Or Moisture.
17. Wet Location Marking :
Apparatus shall not be exposed to dripping or splashing and
no objects filled with liquids, such as vases, shall be placed
on the apparatus.
PORTABLE CART WARNING
Owner’s Manual 5
Contents
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2~4
Introduction
Features Of This TV . . . . . . . . . . . . . . . . . . . . . .6
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Controls and Connection Options . . . . . . . . . .8~9
Remote Control Key Functions . . . . . . . . . .10~11
Installation
Desktop Pedestal Installation . . . . . . . . . . . . . . . .12
External Equipment Connections . . . . . . . . . .13~17
VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Cable TV Setup . . . . . . . . . . . . . . . . . . . . . . . .14
External A/V Source Setup . . . . . . . . . . . . . . . .14
DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
DTV Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . .16~17
Operation
Turning on the Monitor . . . . . . . . . . . . . . . . . . . . .18
Menu Language Selection . . . . . . . . . . . . . . . . . .18
Picture Menu Options
Auto Picture Control (APC) . . . . . . . . . . . . . . . .19
XD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Auto Color Temperature Control . . . . . . . . . . . .19
Fleshtone . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
sRGB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Manual Picture Control . . . . . . . . . . . . . . . . . .21
Sound Menu Options
DASP (Digital Auto Sound Processing) . . . . . . .22
Manual Sound Control . . . . . . . . . . . . . . . . . . .22
BBE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
AVL (Auto Volume Leveler) . . . . . . . . . . . . . . . .23
Timer Menu Options
Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . .24
On/Off Timer Setup . . . . . . . . . . . . . . . . . . . . .24
Auto Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Special Menu Options
Key Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
ISM Method . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Low power . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Screen Menu Options
Auto Adjustment . . . . . . . . . . . . . . . . . . . . . . . .28
Setting Picture Format . . . . . . . . . . . . . . . . . . .28
Cinema Mode Setup . . . . . . . . . . . . . . . . . . . . .29
Screen Position . . . . . . . . . . . . . . . . . . . . . . . .29
Manual Configure . . . . . . . . . . . . . . . . . . . . . . .30
Initializing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Black level adj. . . . . . . . . . . . . . . . . . . . . . . . . .31
PC/DTV Mode . . . . . . . . . . . . . . . . . . . . . . . . .31
Screen Adjustments . . . . . . . . . . . . . . . . . . . . .32
NR(Noise Reduction) . . . . . . . . . . . . . . . . . . . .32
PIP (Picture-in-Picture) Feature
Watching PIP . . . . . . . . . . . . . . . . . . . . . . . . . .33
PIP Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
PIP Transparency . . . . . . . . . . . . . . . . . . . . . . .33
Moving PIP . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Selecting an Input Signal Source for PIP . . . . . .33
DW Setup Options
Watching DW . . . . . . . . . . . . . . . . . . . . . . . . . .34
Sub Picture Size Adjustment . . . . . . . . . . . . . . .34
Swapping the DW . . . . . . . . . . . . . . . . . . . . . . .34
Selecting a Source for the DW . . . . . . . . . . . . .34
External Control Device Setup . . . . . . . . . . . . . . . .35~40
IR Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41~42
Programming the remote . . . . . . . . . . . . . . . . . . . . . . .43
Programming Codes . . . . . . . . . . . . . . . . . . . . . . . .44~45
Troubleshooting Checklist . . . . . . . . . . . . . . . . . . . . . .46
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Contents
Contents
After reading this manual, keep it handy for future reference.
6 Plasma Monitor
Introduction
Introduction
Introduction
Features Of This Monitor
Features Of This Monitor
What is a Plasma Monitor ?
If voltage is applied to gas within glass panels, ultraviolet rays are produced and fused with a fluorescent substance. At that
instant, light is emitted. A Plasma Display is a next generation flat Display using this phenomenon.
160° - Wide angle range of vision
Your flat panel plasma screen offers an exceptionally broad viewing angle -- over 160 degrees. This means that the display is
clear and visible to viewers anywhere in the room.
Wide Screen
The screen of the Plasma Display is 71" so wide that your viewing experience is as if you are in a theater.
Multimedia
Connect your plasma display to a PC and you can use it for conferencing, games, and internet browsing. The Picture-in-Picture
feature allows you to view your PC and video images simultaneously.
Versatile
The light weight and thin size makes it easy to install your plasma display in a variety of locations where conventional TVs would
not fit.
The Plasma Monitor Manufacturing Process: Why minute colored dots may be present on the Plasma
Monitor screen
The Plasma Display Panel which is the display device of this product is composed of 0.9 to 2.2 million cells. A few cell defects will
normally occur in the Plasma Monitor manufacturing process. Several minute colored dots visible on the screen should be accept-
able. This also occurs in other Plasma Monitor manufacturers' products and the tiny dots appearing does not mean that this
Plasma Monitor is defective. Thus a few cell defects are not sufficient cause for the Plasma Monitor to be exchanged or returned.
Our production technology is designed to minimize cell defects during the manufacture and operation of this product.
Cooling Fan Noise
In the same way that a fan is used in a PC computer to keep the CPU (Central Processing Unit) cool, the Plasma Monitor is
equipped with cooling fans to cool the Monitor and improve its reliability. Therefore, a certain level of noise could occur while the
fans are operating and cooling the Plasma Monitor.
The fan noise doesn't have any negative effect on the Plasma Monitor's efficiency or reliability. The noise from these fans is nor-
mal during the operation of this product. We hope you understand that a certain level of noise from the cooling fans is acceptable
and is not sufficient cause for the Plasma Monitor to be exchanged or returned.
Owner’s Manual 7
Introduction
Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer
where you purchased the product.
Owner’s Manual
1.5V
1.5V
Batteries
Power Cord
L
I
G
H
T
I
N
P
U
T
M
O
D
E
P
IP
M
U
T
E
S
L
E
E
P
V
O
L
C
H
W
I
N
.
S
I
Z
E
W
I
N
.
P
O
S
I
T
IO
N
S
W
A
P
M
E
N
U
P
IP
IN
P
U
T
A
R
C
E
X
IT
P
L
A
Y
P
A
U
S
E
S
T
O
P
R
E
C
O
R
D
V
I
D
E
O
C
O
M
1
R
G
B
H
D
M
I
1
E
N
T
E
R
H
D
M
I
2
K
E
Y
L
O
C
K
I
N
D
E
X
R
E
W
F
F
S
K
I
P
P
O
W
E
R
D
W
D
A
S
P
A
P
C
C
O
M
2
Remote Control
Video cables
Audio cables
- Optional extras can be changed or modified for quality improvement without any notification new optional extras can be added.
- Contract your dealer for buying these items.
Option Extras
Option Extras
Tilt wall mounting bracket
Desktop stand
D-sub 15 pin cable
Accessories
Accessories
2- ferrite cores
(for the speaker cables)
Use the ferrite core with the speaker cables
The ferrite core given as a bundled accessory can be used to reduce the electromagnetic waves in the con-
nection to the speakers.
Wind the speaker cable on the ferrite core twice, and then plug the cables into the monitor and the speak-
ers as shown in the following picture:
8 Plasma Monitor
Introduction
Controls
Controls
INPUT
MENU
VOL
TruSurround XT
MENU Button
INPUT Button
VOLUME (FF , GG) Buttons
EE, DD Buttons
INDEX
Switches
LED Display
on or off.
Remote
Control
Sensor
Power Indicator
Illuminates red in standby
mode, Illuminates green when
the monitor is turned on.
Sub power Button
INDEX
Video Mode
Component Mode
RGB-PC/DTV Mode
HDMI1/DVI or HDMI2 Mode
Flat
GG
p.22
Music
GG
p.22
Movie
GG
p.22
Sports
GG
p.22
Off Mode
GG
p.22
TruSurround XT
TruSurround XT
TruSurround XT
TruSurround XT
TruSurround XT
TruSurround XT
TruSurround XT
TruSurround XT
TruSurround XT
TruSurround XT
TruSurround XT
- This is a simplified representation of front panel.
- This picture shown below may be somewhat different from your monitor.
Owner’s Manual 9
Introduction
Connection Options
Connection Options
DIGITAL AUDIO
OUT
OPTICAL
HDMI/DVI IN HDMI/DVI IN
1
2
RS-232C INRS-232C IN
(CONTROL(CONTROL & SER & SERVICE)VICE)
VIDEOVIDEO
AUDIOAUDIO
COMPONENTCOMPONENT IN IN
VIDEOVIDEO
AUDIOAUDIO
MONO
( )
S-VIDEOS-VIDEO
VIDEO INVIDEO IN
VIDEO IN 3VIDEO IN 3 VIDEO IN 4VIDEO IN 4
AUDIO (RGB/DVI)AUDIO (RGB/DVI)
RGB INRGB IN
RGB(PC/DTV)RGB(PC/DTV)
REMOTE REMOTE
CONTROL INCONTROL IN
HDMI IN HDMI IN
1(DVI)1(DVI)
2
RS-232C INRS-232C IN
(CONTROL & SERVICE)
VIDEOVIDEO
AUDIO
COMPONENTCOMPONENT IN IN
VIDEOVIDEO
AUDIOAUDIO
MONO
( )
S-VIDEOS-VIDEO
VIDEO IN
VIDEO IN 3VIDEO IN 3 VIDEO IN 4VIDEO IN 4
AUDIO (RGB/DVI)AUDIO (RGB/DVI)
RGB INRGB IN
RGB(PC/DTV)RGB(PC/DTV)
REMOTE REMOTE
CONTROL INCONTROL IN
AC IN
R
L
EXTERNAL SPEAKER
AC IN
R
L
EXTERNAL SPEAKER
1
6
2
5
7
3
4
HDMI IN
Connect a HDMI signal to 1(DVI) or 2.
Or DVI(VIDEO) signal to the 1(DVI) port with a DVI to
HDMI cable.
RS-232C IN (CONTROL & SERVICE) PORT
Connect to the RS-232C port on a PC.
VIDEO IN
Connect audio/video output from an external device to
these jacks.
S-VIDEO
Connect S-Video out from an S-VIDEO device.
COMPONENT IN
Connect a component video/audio device to these jacks.
EURO SCART SOCKET
Connect the euro scart of the VCR to these sockets.
RGB IN
AUDIO (RGB/DVI) / RGB(PC/DTV)
Connect the monitor output from a PC to the appropriate
input port.
REMOTE CONTROL IN
Connect your wired remote control.
EXTERNAL SPEAKER (8 ohm output)
Connect to optional external speaker(s).
* For further information, refer to ‘Speaker & Speaker
Stand’ manual.
POWER CORD SOCKET
This Monitor operates on an AC power. The voltage is
indicated on the Specifications page. Never attempt to
operate the Monitor on DC power.
1
7
2
3
4
5
6
8
9
8
9
- This picture shown below may be somewhat different from your monitor.
10 Plasma Monitor
Introduction
- When using the remote control, aim it at the remote control sensor on the monitor.
- Under certain conditions such as if the remote IR signal is interrupted, the remote control may not function. Press
the key again as necessary.
Remote Control Key Functions
Remote Control Key Functions
LIGHT
INPUT
MODE
PIP
MUTE
SLEEP
VOL CH
WIN. SIZE
WIN. POSITION
SWAP
MENU
PIP INPUT ARC
EXIT
PLAY PAUSE STOP RECORD
VIDEO COM1 RGB
HDMI1
ENTER
HDMI2
KEY LOCK INDEX
REW FF SKIP
POWER
DW
D
A
S
P
APC
COM2
LIGHT
Illuminates the remote control buttons.
MODE
Selects the remote operating mode: MNT, VCR, DVD,
CABLE, HDSTB or AUDIO.
INPUT
Selects: Video1-2-3-4, Component 1-2, RGB(DTV/PC),
HDMI1/DVI or HDMI2 input sources.
POWER
Turns your monitor or any other programmed equipment on or
off, depending on mode.
PIP
Selects the PIP mode.
DW
Selects the DW mode.
WIN. SIZE
Adjusts the sub picture size.
NUMBER buttons
Dosen’t work for monitor mode.
WIN.POSITION
Moves the sub picture.
SWAP
Exchanges the main/sub images.
XD
Switches the XD on or off.
GG
p.19
MENU
Brings up the main menu to the screen.
PIP INPUT
Selects the input source for the sub picture.
ARC
Changes the picture format.
GG
p. 28
EXIT
Clears all on-screen displays and returns to monitor viewing
from any menu.
Owner’s Manual 11
Introduction
Installing Batteries
• Open the battery compartment cover on the back side and install the batteries
matching correct polarity (+ with +, - with -).
• Install two 1.5V AA batteries. Don’t mix old or used batteries with new ones.
Replace cover.
THUMBSTICK (Up/Down/Left/Right/ENTER)
Navigate the on-screen menus and adjust the system settings
to your preference.
KEY LOCK
Switches the key lock on or off.
INDEX
Switches LED Display on or off.
APC
Adjusts the factory preset picture according to the room.
DASP
To select the sound appropriate to your viewing program
character:
SRS TSXT, Flat, Music, Movie, Sports, or Off
GG
p.22
MUTE
Switches the sound on or off.
SLEEP
Sets the Sleep Timer.
VOLUME UP/DOWN
Increases/decreases the sound level.
CHANNEL UP/DOWN
Selects available channels.
Dosen’t work for monitor mode.
LIGHT
INPUT
MODE
PIP
MUTE
SLEEP
VOL CH
WIN. SIZE
WIN. POSITION
SWAP
MENU
PIP INPUT ARC
EXIT
PLAY PAUSE STOP RECORD
VIDEO COM1 RGB
HDMI1
ENTER
HDMI2
KEY LOCK INDEX
REW FF SKIP
POWER
DW
D
A
S
P
APC
COM2
VIDEO/COM1/COM2/RGB/HDMI1/DVI/HDMI2
Selects: Video1-2-3-4, Component 1-2, RGB-DTV (or RGB-
PC),HDMI1/DVI, HDMI2 input sources.
VCR/DVD/DVHS/Camcorder BUTTONS
Control some video cassette recorders or DVD players
("RECORD" button is not available for DVD player).
12 Plasma Monitor
Installation
Desktop Pedestal Installation
Desktop Pedestal Installation
• Ensure adequate ventilation by following the clearance recommendations.
GROUNDING
Ensure that you connect the grounding / earth wire to prevent possible electric shock. If grounding
methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try
to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.
Power Supply
Short-circuit Breaker
4 inches
4 inches
4 inches
4 inches
For proper ventilation, allow a clearance of 4inches on each side from the wall.
Installation
Installation
• This picture shown below may be somewhat different from your monitor.
Owner’s Manual 13
Installation
External Equipment Connections
External Equipment Connections
NOTE: Not all cables shown are included with the plasma display.
- To avoid picture noise (interference), leave an adequate distance between the VCR and Monitor.
- Use the ISM Method feature to avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still
picture from a VCR. If the 4:3 picture format is used; the fixed image may remain visible on the screen after the image is
changed or when the unit is off.
How to connect
1. Connect the audio and video cables from the VCR's output
jacks to the monitor input jacks, as shown in the figure.
When connecting the monitor to VCR, match the jack colors
(Video = yellow, Audio Left = white, and Audio Right = red).
2. If you connect an S-VIDEO output from VCR to the S-
VIDEO input, the picture quality is improved; compared to
connecting a regular VCR to the Video input.
3. If you connect the Euro scart socket of the VCR to the Euro
scart socket of the set. No other connection is needed.
Mono VCR: Connect the video output cable from the VCR
to the VIDEO input on the monitor.
S-VIDEO VCR: Connect the S-Video output cable from the
VCR to the S-VIDEO input on the monitor. (Note that S-
Video offers higher quality).
How to use
1. Insert a video tape into the VCR and press PLAY on the
VCR.
(Refer to the VCR owner’s manual.)
2. Use the INPUT button on the remote control to select
Video 1.
(If connected to VIDEO 2, VIDEO 3 or VIDEO 4, select the
Video 2, Video 3 or Video 4 input source.)
VCR Setup
VCR Setup
VIDEO
AUDIO
COMPONENT IN
VIDEO
AUDIO
MONO
( )
S-VIDEO
VIDEO INVIDEO IN
VIDEO IN 3 VIDEO IN 4
S-VIDEO
OUT
IN
(R) AUDIO (L)VIDEO
34
OUTPUT
SWITCH
ANT OUT
ANT IN
VCR
or
14 Plasma Monitor
Installation
- After subscribing to a cable monitor service from a local provider and installing a converter, you can watch cable TV program-
ming. The monitor cannot display monitor programming unless a TV tuner device or cable TV converter box is connected to the
Monitor.
- For further information regarding cable monitor service, contact your local cable TV service provider(s).
How to connect
1. Connect the audio and video cables from the Cable Box's output
jacks to the monitor input jacks, as shown in the figure.
When connecting the monitor to a Cable Box, match the jack colors
(Video = yellow, Audio Left = white, and Audio Right = red).
Or, connect the Euro scart socket of the Cable box to the Euro scart
socket of the set.
How to use
1. Use the INPUT button on the remote control to select Video 1.
(If connected to VIDEO 2, VIDEO 3 or VIDEO 4, select the Video 2,
Video 3 or Video 4 input source.)
2. Select your desired channel with the remote control for cable box.
Cable
Cable
TV Setup
TV Setup
VIDEOVIDEO
AUDIOAUDIO
COMPONENTCOMPONENT IN IN
VIDEOVIDEO
AUDIOAUDIO
MONO
( )
S-VIDEOS-VIDEO
VIDEO IN
TV
VCR
RF Cable
(R) AUDIO (L)
VIDEO
Cable Box
How to connect
1. Connect the audio and video cables from the external
equipment's output jacks to the monitor input jacks, as
shown in the figure.
When connecting the monitor to external equipment, match
the jack colors (Video = yellow, Audio Left = white, and
Audio Right = red).
Or, connect the Euro scart socket of the External A/V to the
Euro scart socket of the set.
How to use
1. Use the INPUT button on the remote control to select
Video1.(If connected to VIDEO 2, VIDEO 3 or VIDEO 4,
select the Video 2, Video 3 or Video 4 input source.)
2. Operate the corresponding external equipment. Refer to
external equipment operating guide.
External
External
A/V Source Setup
A/V Source Setup
VIDEOVIDEO
AUDIOAUDIO
COMPONENTCOMPONENT IN IN
VIDEOVIDEO
AUDIOAUDIO
MONO
( )
S-VIDEOS-VIDEO
VIDEO INVIDEO IN
RL
AUDIO
VIDEO
Video Game Set
Camcorder
Owner’s Manual 15
Installation
• Component Input ports
To get better picture quality, connect a DVD
player to the component input ports as shown.
How to connect
1. Use the monitor’s COMPONENT (Y, PB, PR) INPUT, RGB or HDMI IN 1(DVI) to HDMI jack for video connec-
tions, depending on your set-top box connector. Then, make the corresponding audio connections.
How to use
1. Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)
2. Use INPUT on the remote control to select Component 1, Component 2, RGB, HDMI1/DVI or HDMI2.
DTV Setup
DTV Setup
Component ports of the
Monitor
Y
PB
PR
Video output ports
of DVD player
Y
Y
Y
Y
Pb
B-Y
Cb
P
B
Pr
R-Y
Cr
PR
How to connect
1. Connect the DVD video outputs to the COMPONENT (Y, PB, PR) or HDMI IN 1(DVI) jacks and connect the
DVD audio outputs to the AUDIO INPUT jacks on the monitor, as shown in the figure.
2. If your DVD only has an S-Video output jack, connect this to the S-VIDEO input on the monitor and connect the
DVD audio outputs to the AUDIO INPUT jacks on the monitor, as shown in the figure.
How to use
1. Turn on the DVD player, insert a DVD.
2. Use the INPUT button on the remote control to select Component 1, Component 2, HDMI1/DVI or 2. (If con-
nected to S-VIDEO, select the Video 1 external input source.)
3. Refer to the DVD player's manual for operating instructions.
DVD Setup
DVD Setup
AUDIO (RGB/DVI)AUDIO (RGB/DVI)
RGB INRGB IN
RGB(PC/DTV)RGB(PC/DTV)
REMOTE REMOTE
CONTROL INCONTROL IN
RGB-DTV OUTPUT
(R) AUDIO (L)
HDMI OUTPUT
VIDEOVIDEO
AUDIO
COMPONENTCOMPONENT IN
VIDEOVIDEO
AUDIOAUDIO
MONO
( )
S-VIDEOS-VIDEO
VIDEO IN
B
R
(R) AUDIO (L)
HDMI IN HDMI IN
1
2
RS-232C INRS-232C IN
(CONTROL & SERVICE)
DVI-DTV OUTPUT
DVD
Digital Set-top Box
or
or
HDMI IN HDMI IN
RS-232C INRS-232C IN
(CONTROL & SERVICE)
VIDEOVIDEO
AUDIO
COMPONENTCOMPONENT IN IN
VIDEOVIDEO
AUDIOAUDIO
MONO
( )
S-VIDEOS-VIDEO
VIDEO INVIDEO IN
HDMI OUTPUT
VIDEO
AUDIO
COMPONENT IN
VIDEO
AUDIO
( )
S-VIDEO
VIDEO IN
(R) AUDIO (L)
S-VIDEO
1(DVI)1(DVI)
2
HDMI IN
RS-232C IN
(CONTROL & SERVICE)
VIDEO
AUDIO
COMPONENT IN
VIDEO
AUDIO
( )
S-VIDEO
VIDEO IN
VIDEOVIDEO
AUDIOAUDIO
COMPONENT IN
B
R
(R) AUDIO (L)
VIDEOVIDEO
AUDIOAUDIO
MONO
( )
S-VIDEOS-VIDEO
VIDEO INVIDEO IN
1(DVI)
2
- To watch digitally broadcast programs, purchase and connect a digital set-top box.
- This monitor supports HDCP (High-bandwidth Digital Contents Protection) protocol for
HDMI/DVI-DTV (480p,720p,1080i, 1080p) mode.
16 Plasma Monitor
Installation
How to connect
1. To get the best picture quality, adjust the PC
graphics card to a 1600x1200, 60Hz.
2. Use the monitor’s RGB INPUT or HDMI IN 1(DVI)
port for video connections, depending on your PC
connector.
If the graphic card on the PC does not output ana-
log and digital RGB simultaneously, connect only
one of either RGB IN or HDMI IN 1(DVI) to display
the PC on the monitor.
If the graphic card on the PC does output analog
and digital RGB simultaneously, set the monitor to
either RGB or HDMI1/DVI; (the other mode is set
to Plug and Play automatically by the monitor.)
3. Then, make the corresponding audio connections.
If using a sound card, adjust the PC sound as
required.
How to use
1. Turn on the PC and the monitor.
2. Turn on the display by pressing the POWER button on the monitor's remote control.
3. Use the INPUT button on the remote control to select RGB or HDMI1/DVI.
4. Check the image on your monitor. There may be noise associated with the resolution, vertical pattern, contrast or
brightness in PC mode. If noise is present, change the PC mode to another resolution, change the refresh rate to
another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC
graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card.
NOTES: • Avoid keeping a fixed image on the monitor's screen for a long period of time. The fixed image may become
permanently imprinted on the screen. Use the Orbiter screen saver when possible.
• The synchronization input form for Horizontal and Vertical frequencies is separate.
PC Setup
PC Setup
AUDIO (RGB/DVI)AUDIO (RGB/DVI)
RGB IN
RGB(PC/DTV)RGB(PC/DTV)
REMOTE
CONTROL IN
HDMI IN
RS-232C IN
(CONTROL & SERVICE)
1(DVI)1(DVI)
2
- This monitor provides Plug and Play capability, meaning that the PC adjusts automatically to its settings. The monitor sends
configuration information (EDID) to the PC using the Video Electronics Standard Association (VESA) Display Data Channel
(DDC) protocol.
- The monitor perceives 640x480, 60Hz as DTV 480p based on the PC graphic card. In this case, change the screen scanning
rate for the graphic card.
Owner’s Manual 17
Installation
Monitor Display Specifications (RGB-PC / HDMI/DVI-PC Mode)
Resolution
720x400
640x480
800x600
Horizontal
Frequency(KHz)
31.469
31.469
35.000
37.861
37.500
43.269
37.879
46.875
53.674
49.725
48.363
56.476
60.023
63.981
80.000
75.00
66.587
70.08
59.94
66.66
72.80
75.00
85.00
60.31
75.00
85.06
74.55
60.00
70.06
75.02
60.02
75.00
60.00
59.934
Vertical
Frequency(Hz)
832x624
1024x768
1600x1200
1920x1080
1280x1024
- HDMI
TM
, the HDMI logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of HDMI
Licensing."
- This monitor can receive the High-Definition Multimedia
Interface(HDMI).
- This monitor supports HDCP(High-bandwidth Digital
Contents Protection) Protocol for 480p, 720p, 1080i, 1080p
modes.
- When you Connect with HDMI Source Devices (DVD Player
or Set Top Box) supporting Auto HDMI function, automatical-
ly, support Plug & Play and then set the HDMI Source
Devices(1920 x 1080i). After reading in HDMI Source Devices
using Display Data Channel(DDC) Protocol, EDID stored in
monitor is used. If HDMI Source Devices not supported Auto
HDMI is been, the Resolution is setted, manually.
- To get the best picture quality, adjust the DVD Player or Set
Top Box output resolution to 1920 x 1080i.
How to connect
When Source Devices(DVD Player or Set Top Box) support
HDMI.
- If Source Devices have HDMI Output Connector, Source
Devices connect to DTV with HDMI Cable.(not supplied with
the product).
- If Source Devices support Auto HDMI, automatically, Source
Devices divert output resolution in 1920 x 1080i. But if not,
resolution divert Manually Setting for reference Manual of
Source Devices.
- To get the best picture quality, adjust the DVD Player or Set
Top Box output resolution to 1920 x 1080i.
- Because HDMI sends Digital Video and Audio with one cable,
need not especial Audio Cable for using HDMI Cable.
18 Plasma Monitor
Operation
Operation
Operation
Menu Language Selection
Menu Language Selection
T
T
urning on the Monitor
urning on the Monitor
Turning on the Monitor just after installation
1. Connect power cord correctly. At this moment, the Monitor is switched to standby mode.
2. Press the INPUT or button on the Monitor or press the POWER, INPUT button on the remote
control and then the Monitor will switch on.
- The menus can be shown on the screen in the selected language. First select your language.
1. Press the MENU button and then use
DD
/
EE
button to select the SPECIAL menu.
2. Press the GG button and then use
DD
/
EE
button to select Language.
3. Press the GG button and then use
DD
/
EE
button to select your desired language.
From this point on, the on-screen menus will be shown in the language of your choice.
4. Press the ENTER button to save.
• Press the MENU button to return to the previous menu.
Owner’s Manual 19
Operation
1. Press the APC button repeatedly to select the picture appearance setup option as shown below.
Auto Picture Control (APC)
Auto Picture Control (APC)
- To initialize values (reset to default settings), select the Cool option.
1. Press the MENU button and then use
DD / EE
button to select the PICTURE menu.
2. Press the GG button and then use
DD / EE
button to select ACC .
3. Press the
GG button and then use
DD / EE
button to select either Cool (Default), Normal
(Preset), Warm (Preset).
4. Press the ENTER button to save the new settings.
Auto Color
Auto Color
T
T
emperature Control
emperature Control
- APC adjusts the Monitor for the best picture appearance.
- When adjusting Picture menu options (contrast, brightness, color, sharpness, and tint) manually, APC automati-
cally changes to Off.
- Readjust Picture menu settings for each following input source as preferred.
Picture Menu Options
Picture Menu Options
• You can also select Daylight, Optimum, Night time or Off in the PICTURE menu.
• Daylight, Optimum, and Night time settings are preset for optimum picture quality at the factory and cannot be
changed.
Daylight Optimum Night time Off
- XD is LG Electronic’s unique picture improving technology to display a real HD
source through an advanced digital signal processing algorithm.
- When selecting APC options (Daylight, Optimum and Night time), XD is auto-
matically change to On.
XD
XD
1. Press the button repeatedly as shown below.
On Off
APC
ACC
Fleshtone
Contrast 100
Brightness 55
Color 55
Sharpness 60
Tint 0
APC
ACC GG
Fleshtone
Contrast 100
Brightness 55
Color 55
Sharpness 60
Tint 0
Cool
Normal
Warm
20 Plasma Monitor
Operation
Picture Menu Options continued
Picture Menu Options continued
- Use Fleshtone to select the desired skin color option.
1. Press the MENU button and then use
DD / EE
button to select the PICTURE menu.
2. Press the GG button and then use
DD / EE
button to select Fleshtone.
3. Press the
GG button and then use FF / GG button to make appropriate adjustments.
• The adjustment range is 0 ~ 3.
4. Press the ENTER button to save the new settings.
Fleshtone (V
Fleshtone (V
ideo1-2-3-4, Component 1-2, RGB-DTV
ideo1-2-3-4, Component 1-2, RGB-DTV
, HDMI1/DVI-DTV
, HDMI1/DVI-DTV
, HDMI2-DTV Mode only)
, HDMI2-DTV Mode only)
- If the monitor is connected to external equipment using sRGB, set sRGB to On to adjust for the color difference.
1. Press the MENU button and then use
DD / EE
button to select the PICTURE menu.
2. Press the GG button and then use
DD / EE
button to select sRGB.
3. Press the
GG
button and then use
DD / EE
button to select On or Off.
4. Press the ENTER button to save the new settings.
sRGB (only RGB-PC, HDMI1/DVI-PC Modes)
sRGB (only RGB-PC, HDMI1/DVI-PC Modes)
APC
ACC
Fleshtone
Contrast 100
Brightness 55
Color 55
Sharpness 60
Tint 0
APC
ACC
Fleshtone GG
Contrast 100
Brightness 55
Color 55
Sharpness 60
Tint 0
0
APC
ACC
sRGB
Contrast 100
Brightness 55
Color 55
APC
ACC
sRGB GG
Contrast 100
Brightness 55
Color 55
On
Off
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/