CSI Pure Digital Fiberlink 7222 User manual

Brand: CSI

Model: Pure Digital Fiberlink 7222

Type: User manual

This manual is also suitable for

CSI Pure Digital Fiberlink 7222 is a transmitter unit that provides 4 optical outputs of RGBHV video with stereo audio. Each output transmits over one single mode or multimode fiber at 1310 nm wavelength. The unit is designed to provide point-to-multipoint signal distribution and is compatible with all receiver units within the 7220 Series. The unit’s all digital encoding delivers noise-free transmissions that retain all of their initial parameters, regardless of fiber optic cable attenuation.

P/N: 123189 Rev. B

Models 7222, 7224 and 7226

RGBHV Video with

Stereo Audio

USER’S MANUAL

WORLD HEADQUARTERS

55 Cabot Court

Hauppauge, N.Y. 11788 USA

Tel: (631) 273-0404 Fax: (631) 273-1638

www.commspecial.com

Email: [email protected]

Communications Specialties Pte Ltd

100 Beach Road

#22-09 Shaw Tower

Singapore 189702

Tel: +65 6391 8790 Fax: +65 6396 0138

Email: [email protected]

General Information ................................................... 2

Introduction ............................................................ 2

Technical Specifications ......................................... 2

Installation Instructions .............................................. 4

Installation Procedure ............................................. 4

System Connections ............................................... 5

Indicator LEDs ....................................................... 6

Operating Pointers and Troubleshooting ................... 6

Maintenance and Repairs ........................................... 7

Limited Warranty ....................................................... 8

CONTENTS

LIMITED WARRANTY

Communications Specialties, Inc. (CSI) warrants that for a period of

three years after purchase by the Buyer, the Pure Digital Fiberlink

7222, 7224 and 7226 transmitters will be free from defects in material

and workmanship under normal use and service. A Return Material Au-

thorization (RMA) number must be obtained from CSI before any equip-

ment is returned by the Buyer. CSI’s obligation under this warranty

will be limited, at its option, to either the repair or replacement of de-

fective units, including free materials and labor. In no event shall CSI

be responsible for any incidental or consequential damages or loss of

profits or goodwill. CSI shall not be obligated to replace or repair equip-

ment that has been damaged by fire, war, acts of God, or similar causes,

or equipment that has been serviced by unauthorized personnel, altered,

improperly installed or abused.

RMA numbers and repairs can be obtained from:

Communications Specialties, Inc.

55 Cabot Court

Hauppauge, NY 11788 USA

Tel: (631) 273-0404 Fax: (631) 273-1638

www.commspecial.com Email: info@commspecial.com

Or, in the Asia Pacific Region:

Communications Specialties Pte Ltd

100 Beach Road, #22-09 Shaw Tower

Singapore 189702

Tel: +65 6391 8790 Fax: +65 6396 0138

Email: csiasia@commspecial.com

Please have your serial number (located on the top label of the unit)

available with contacting us.

GENERAL INFORMATION

The Pure Digital Fiberlink

7222, 7224 and 7226 transmitter units

provide 4, 8 and 12 optical outputs respectively of RGBHV video with

stereo audio. Each output transmits over one single mode or multimode

fiber at 1310 nm wavelength. The units are designed to provide point-

to-multipoint signal distribution and are compatible with all receiver

units within the 7220 Series.

The units’ all digital encoding delivers noise-free transmissions that

retain all of their initial parameters, regardless of fiber optic cable at-

tenuation. System operation may be easily monitored using integral in-

dicator LEDs on each unit that continuously signify the presence of

baseband video and audio signals.

Introduction

Technical Specifications

Model Part Number Configurations:

All units transmit at

1310 nm wavelength

over single mode or

multimode fiber. ST

connectors are

provided.

Video:

Input Impedance ....................... RGB: 75 Ohms; H&V: Hi-Z

Input Level ............................... RGB: 714 mV p-p; H&V: 3 to 5 V p-p

H Sync Frequency Range ......... 31.5 to 60 kHz

V Sync Frequency Range ......... 30 to 85 Hz

Number of Video Channels ...... 1 RGBHV

RGB Format Supported ............ RGB with separate H and V

Unit Type Part Number

Four output transmitter 7222-7S-PP*

Eight output transmitter 7224-7S-PP*

Twelve output transmitter 7226-7S-PP*

*PP Values (line cord): NA = N. America, AU = Australia,

EU = Europe, JP = Japan, UK = United Kingdom

Therefore, any minute particles of dirt or dust can easily block the fiber

from accepting or radiating light. To prevent this from happening, al-

ways use the provided dust caps whenever optical connectors are ex-

posed to air. It is also a good idea to gently clean the tip of an optical

connector with a lint-free cloth moistened with alcohol whenever dust

is suspected.

The status of the VIDEO and AUDIO indicator LEDs should provide

the first clue as to the origin of an operational failure. If these are off, it

usually means that the fiber is broken or has too much attenuation. Next,

be certain that the input and output signal connections are correct.

If, after reviewing the above possibilities, the system is still not oper-

ating, please contact the Customer Service Department for further as-

sistance.

MAINTENANCE AND REPAIRS

The Pure Digital Fiberlink

7222, 7224 and 7226 transmitters have

been manufactured using the latest semiconductor devices and tech-

niques that electronic technology has to offer. They have been designed

for long, reliable and trouble-free service and are not normally field

repairable. Should difficulty be encountered, Communications Special-

ties maintains a complete service facility to render accurate, timely and

reliable service of all products.

The only maintenance that can be provided by the user is to ascertain

that the optical connectors are free of dust or dirt that could interfere

with light transmission and that electrical connections are secure and

accurate. DANGER! Always turn off the transmitter’s power before

removing the optical fiber from the unit!

All other questions or comments should be directed to our Customer

Service Department. It should be noted that many “problems” can eas-

ily be solved by a simple phone call.

Miscellaneous:

Operating Temp. Range ........... -20 to +50 degrees C

Operating Power ...................... 95-250 volts AC, 47-63 Hz, 9 watts

Signal Connectors ................................ HD-15F

RGB Processing ................................... 24 bits, no compression or

scaling

Optical:

Operating Wavelength ......................... 1310 nm; MM or SM

Optical Fiber ........................................ 62.5/125 microns MM,

50/125 microns MM or

8-10/125 microns SM

Optical Connector ................................ ST

Class I Laser Product complies with FDA performance standard for

laser products, Title 21, Code of Federal Regulations, Sub-Chapter J

Audio:

Number of Audio Channels .................. 2, unbalanced

Frequency Response ............................. +0/-0.5 dB, 20 Hz to 20 kHz

Input Impedance ................................... >24 k Ohms

Output Impedance ................................ <1 Ohm

Maximum Audio Level ........................ +10 dBu

THD+N ................................................. 0.005%; 20 Hz - 20 kHz

SNR (A-Weighted) ............................... 95 dB

Channel Phase Differential ................... +/-0.1

Crosstalk ............................................... Min. 95 dB (1 kHz)

Signal Connectors ................................ 3.5mm Stereo jack

Audio to Video Diff. Delay (skew) ..... <300 uS

Power: ON: (GREEN) Indicates that correct power has been applied.

Video: OFF: Indicates no video detected on the input.

BLINKING GREEN: Indicates either H or V sync detected at

the input but not both.

STEADY GREEN: Indicates both H and V sync detected on

the input.

Audio: OFF: Indicates no audio detected on the transmitter unit.

BLINKING: Indicates audio detected on the transmitter unit.

Indicator LEDs:

The Pure Digital Fiberlink

7222, 7224 and 7226

transmitters each have three integral indicator LEDs that are used to

monitor the state of the unit.

The status of the LEDs are as follows:

OPERATING POINTERS AND TROUBLESHOOTING

Optical Fiber:

The 7222, 7224 and 7226 transmitters operate with most

multimode (MM) and single mode (SM) optical fibers. All models within

the 7220 Series use the same 1310 nm wavelength and optics for trans-

mitting over multimode or single mode fiber, but be aware that the type

of fiber you use will affect the system’s loss budget and the maximum

transmission distance that it can support.

Troubleshooting:

Multimode fiber optic cable contains an optical fiber with a light

carrying “core” that is only .0025 inches (62.5 microns) in diameter.

Single mode fiber optic cable has an even smaller “core,” only .00032

to .0004 inches (8-10 microns). This is smaller than a human hair!

INSTALLATION INSTRUCTIONS

Installation Procedure:

The Pure Digital Fiberlink

7222, 7224 and 7226 units are ready for

immediate use. Each model features indicator LEDs for monitoring pur-

poses. The following instructions describe the typical installation pro-

cedure and the function of the LED indicators.

1. Connect the video source to the video INPUT RGBHV connector on

the transmitter unit.

2. Connect the audio input signals to the transmitter AUDIO jack.

3. Optionally, connect the LOOP THROUGH RGBHV output to a com-

puter monitor or other destination.

4. Optionally, connect the LOOP THROUGH AUDIO output to speakers

or other destination.

Loss Budget and Maximum Transmission Distance:

Wavelength Loss Budget (in dB) Distance* (in km)

1310 MM 0-15 0-0.75

1310 SM 0-15 0-30

*Distance specifications are only approximate and are not

guaranteed. Operating loss budget must not be exceeded.

DANGER! The transmitting element in the Pure Digital Fiberlink 7222, 7224 and

7226 transmitter units contain solid state Laser Diodes located within the

optical connectors. These lasers emit invisible infrared electromagnetic

radiation which can be harmful to human eyes. The radiation from these optical

connectors, if viewed at close range without a fiber optic cable connected to

the optical connector, may be of sufficient intensity to cause instantaneous

damage to the retina of the eye. Direct viewing of this radiation should be avoided

at all times.

5. Connect fiber optic cable(s) between each optical output that will be

used and a corresponding Pure Digital Fiberlink 7220 Series receiver

unit. BE SURE TO LEAVE PROTECTIVE CAPS ON ANY OUT-

PUTS THAT WILL NOT BE USED.

6. Turn unit on, causing the green POWER LED to light.

7. The VIDEO and AUDIO LEDs will give an indication as described

on the following page.

8. The system should now be operational.

System Connections:

The input and output connections for the Pure Digital Fiberlink

7222, 7224 and 7226 models are as follows:

Audio Connector INPUT and LOOP-THRU: 3.5mm stereo jack

Video Connector INPUT and LOOP-THRU: HD-15F connector

Video Pin Out: Input Loop-Through

1 Red In Red Out

2 Green In Green Out

3 Blue In Blue Out

4 N/C N/C

5 Ground Ground

6 Ground Ground

7 Ground Ground

8 Ground Ground

9 N/C N/C

10 Ground Ground

11 N/C N/C

12 N/C N/C

13 Hor. Sync. In Hor. Sync Out

14 Vert. Sync In Vert. Sync Out

15 N/C N/C

INSTALLATION INSTRUCTIONS

Installation Procedure:

The Pure Digital Fiberlink

7222, 7224 and 7226 units are ready for

immediate use. Each model features indicator LEDs for monitoring pur-

poses. The following instructions describe the typical installation pro-

cedure and the function of the LED indicators.

1. Connect the video source to the video INPUT RGBHV connector on

the transmitter unit.

2. Connect the audio input signals to the transmitter AUDIO jack.

3. Optionally, connect the LOOP THROUGH RGBHV output to a com-

puter monitor or other destination.

4. Optionally, connect the LOOP THROUGH AUDIO output to speakers

or other destination.

Loss Budget and Maximum Transmission Distance:

Wavelength Loss Budget (in dB) Distance* (in km)

1310 MM 0-15 0-0.75

1310 SM 0-15 0-30

*Distance specifications are only approximate and are not

guaranteed. Operating loss budget must not be exceeded.

DANGER! The transmitting element in the Pure Digital Fiberlink 7222, 7224 and

7226 transmitter units contain solid state Laser Diodes located within the

optical connectors. These lasers emit invisible infrared electromagnetic

radiation which can be harmful to human eyes. The radiation from these optical

connectors, if viewed at close range without a fiber optic cable connected to

the optical connector, may be of sufficient intensity to cause instantaneous

damage to the retina of the eye. Direct viewing of this radiation should be avoided

at all times.

5. Connect fiber optic cable(s) between each optical output that will be

used and a corresponding Pure Digital Fiberlink 7220 Series receiver

unit. BE SURE TO LEAVE PROTECTIVE CAPS ON ANY OUT-

PUTS THAT WILL NOT BE USED.

6. Turn unit on, causing the green POWER LED to light.

7. The VIDEO and AUDIO LEDs will give an indication as described

on the following page.

8. The system should now be operational.

System Connections:

The input and output connections for the Pure Digital Fiberlink

7222, 7224 and 7226 models are as follows:

Audio Connector INPUT and LOOP-THRU: 3.5mm stereo jack

Video Connector INPUT and LOOP-THRU: HD-15F connector

Video Pin Out: Input Loop-Through

1 Red In Red Out

2 Green In Green Out

3 Blue In Blue Out

4 N/C N/C

5 Ground Ground

6 Ground Ground

7 Ground Ground

8 Ground Ground

9 N/C N/C

10 Ground Ground

11 N/C N/C

12 N/C N/C

13 Hor. Sync. In Hor. Sync Out

14 Vert. Sync In Vert. Sync Out

15 N/C N/C

Miscellaneous:

Operating Temp. Range ........... -20 to +50 degrees C

Operating Power ...................... 95-250 volts AC, 47-63 Hz, 9 watts

Signal Connectors ................................ HD-15F

RGB Processing ................................... 24 bits, no compression or

scaling

Optical:

Operating Wavelength ......................... 1310 nm; MM or SM

Optical Fiber ........................................ 62.5/125 microns MM,

50/125 microns MM or

8-10/125 microns SM

Optical Connector ................................ ST

Class I Laser Product complies with FDA performance standard for

laser products, Title 21, Code of Federal Regulations, Sub-Chapter J

Audio:

Number of Audio Channels .................. 2, unbalanced

Frequency Response ............................. +0/-0.5 dB, 20 Hz to 20 kHz

Input Impedance ................................... >24 k Ohms

Output Impedance ................................ <1 Ohm

Maximum Audio Level ........................ +10 dBu

THD+N ................................................. 0.005%; 20 Hz - 20 kHz

SNR (A-Weighted) ............................... 95 dB

Channel Phase Differential ................... +/-0.1

Crosstalk ............................................... Min. 95 dB (1 kHz)

Signal Connectors ................................ 3.5mm Stereo jack

Audio to Video Diff. Delay (skew) ..... <300 uS

Power: ON: (GREEN) Indicates that correct power has been applied.

Video: OFF: Indicates no video detected on the input.

BLINKING GREEN: Indicates either H or V sync detected at

the input but not both.

STEADY GREEN: Indicates both H and V sync detected on

the input.

Audio: OFF: Indicates no audio detected on the transmitter unit.

BLINKING: Indicates audio detected on the transmitter unit.

Indicator LEDs:

The Pure Digital Fiberlink

7222, 7224 and 7226

transmitters each have three integral indicator LEDs that are used to

monitor the state of the unit.

The status of the LEDs are as follows:

OPERATING POINTERS AND TROUBLESHOOTING

Optical Fiber:

The 7222, 7224 and 7226 transmitters operate with most

multimode (MM) and single mode (SM) optical fibers. All models within

the 7220 Series use the same 1310 nm wavelength and optics for trans-

mitting over multimode or single mode fiber, but be aware that the type

of fiber you use will affect the system’s loss budget and the maximum

transmission distance that it can support.

Troubleshooting:

Multimode fiber optic cable contains an optical fiber with a light

carrying “core” that is only .0025 inches (62.5 microns) in diameter.

Single mode fiber optic cable has an even smaller “core,” only .00032

to .0004 inches (8-10 microns). This is smaller than a human hair!

GENERAL INFORMATION

The Pure Digital Fiberlink

7222, 7224 and 7226 transmitter units

provide 4, 8 and 12 optical outputs respectively of RGBHV video with

stereo audio. Each output transmits over one single mode or multimode

fiber at 1310 nm wavelength. The units are designed to provide point-

to-multipoint signal distribution and are compatible with all receiver

units within the 7220 Series.

The units’ all digital encoding delivers noise-free transmissions that

retain all of their initial parameters, regardless of fiber optic cable at-

tenuation. System operation may be easily monitored using integral in-

dicator LEDs on each unit that continuously signify the presence of

baseband video and audio signals.

Introduction

Technical Specifications

Model Part Number Configurations:

All units transmit at

1310 nm wavelength

over single mode or

multimode fiber. ST

connectors are

provided.

Video:

Input Impedance ....................... RGB: 75 Ohms; H&V: Hi-Z

Input Level ............................... RGB: 714 mV p-p; H&V: 3 to 5 V p-p

H Sync Frequency Range ......... 31.5 to 60 kHz

V Sync Frequency Range ......... 30 to 85 Hz

Number of Video Channels ...... 1 RGBHV

RGB Format Supported ............ RGB with separate H and V

Unit Type Part Number

Four output transmitter 7222-7S-PP*

Eight output transmitter 7224-7S-PP*

Twelve output transmitter 7226-7S-PP*

*PP Values (line cord): NA = N. America, AU = Australia,

EU = Europe, JP = Japan, UK = United Kingdom

Therefore, any minute particles of dirt or dust can easily block the fiber

from accepting or radiating light. To prevent this from happening, al-

ways use the provided dust caps whenever optical connectors are ex-

posed to air. It is also a good idea to gently clean the tip of an optical

connector with a lint-free cloth moistened with alcohol whenever dust

is suspected.

The status of the VIDEO and AUDIO indicator LEDs should provide

the first clue as to the origin of an operational failure. If these are off, it

usually means that the fiber is broken or has too much attenuation. Next,

be certain that the input and output signal connections are correct.

If, after reviewing the above possibilities, the system is still not oper-

ating, please contact the Customer Service Department for further as-

sistance.

MAINTENANCE AND REPAIRS

The Pure Digital Fiberlink

7222, 7224 and 7226 transmitters have

been manufactured using the latest semiconductor devices and tech-

niques that electronic technology has to offer. They have been designed

for long, reliable and trouble-free service and are not normally field

repairable. Should difficulty be encountered, Communications Special-

ties maintains a complete service facility to render accurate, timely and

reliable service of all products.

The only maintenance that can be provided by the user is to ascertain

that the optical connectors are free of dust or dirt that could interfere

with light transmission and that electrical connections are secure and

accurate. DANGER! Always turn off the transmitter’s power before

removing the optical fiber from the unit!

All other questions or comments should be directed to our Customer

Service Department. It should be noted that many “problems” can eas-

ily be solved by a simple phone call.