May 1991 FORM:
Use above FORM number when ordering extra manuals.
OWNER’S MANUAL
OM-093 322
FTC-14
FTC-23
The data contained in this supplement is either in addition to or takes exception to data appearing later
in this manual.
IMPORTANT:
The FTC-14 (Finger T
ip Control) is equipped with a 14-pin Amphenol plug for connection to the power
source.
The FTC-23 (Finger Tip Control) is equipped with a 5-pin Amphenol plug for connection to the power source.
Contact your local distributor for correct adapter if Amphenol plug on FTC-14/FTC-23 does not mate with intended
power source receptacle.
WARNING: ELECTRIC SHOCK can kill.
•
Do not touch live electrical parts.
•
Shut
down welding power source, and be sure it cannot be accidentally energized before making re
-
mote control connections.
•
Be sure remote switch is fully in the off position before turning on or off the welding power source.
A. Installation
1. The
remote control consists of a 28 ft. (8.5 mm) electrical cord with an Amphenol plug on one
end and a finger tip
control switch device on the other. Position the supplied switch on the electrode holder gun so that the
operator’s thumb can manipulate the rotating switch.
2. Secure the switch in position by taping it to the electrode holder gun with insulated electrical tape.
3. The remote control is connected to the REMOTE CONTACTOR AND CURRENT receptacle on the welding
power
source as follows: align keyway
, insert plug into receptacle, and rotate threaded collar fully clockwise.
B. Operation
The
remote control is both a remote contactor control and a remote current control device. Initial clockwise rotation of
the control will close the contactor circuitry and energize the welding power source.
Continued
clockwise rotation of the control will increase the output current level up to that established by the welding
power source CURRENT CONTROL setting.
Rotating the control fully counterclockwise reduces the current output to zero and deenergizes the contactor.
Description
Quantity
Model
FTC14 FTC23
Part
No.
008 356 SWITCH, contactor current thumb control 1 1.
. . . . . . . . . . . . . . . . . . . . . . . . . . .
052 246 CABLE, pwr No. 20ga 5/c (order by ft) 28ft 28ft.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
144 310 HOUSING PLUG & PINS, (consisting of) 1.
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
134 732 · TERMINAL, male 1 pin 24-20 wire 14.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
079 739 CLAMP, cable stain relief sz 17 1.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
039 273 PLUG, 5 pin MS-3106A-16S-8P 1.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
039 685 CLAMP, cable AN-3057-8 1.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
604 311 GROMMET, rbr .250 ID x .375mtg hole 1.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BE
SURE T
O PROVIDE MODEL AND SERIAL NUMBER WHEN ORDERING REPLACEMENT P
ARTS.
-
1
Miller FTC-23 Owner's manual
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Miller JE802550 Owner's manual
-
-
Miller JK674521 Owner's manual
-
-
-
-
-
-
-