3M Red Dot™ Neonatal, Pre-Wired, Radiolucent Monitoring Electrode Operating instructions

Brand: 3M

Model: Red Dot™ Neonatal, Pre-Wired, Radiolucent Monitoring Electrode

Type: Operating instructions

This manual is also suitable for

Red Dot™ ECG Monitoring Electrodes, Infant, Pre-Wired, Radiolucent, 2283

Application Instructions

Prepare the skin.

Application sites must be clean, dry

and free of any body lotions. Cleaning

with isopropyl alcohol should be

avoided or limited to situations in

which electrode adhesion is an issue

(excessively oily or lotion covered skin).

If alcohol is used, allow it to dry prior

to electrode application.

Excessive hair at the site should be

removed by clipping.

Apply the electrodes.

Remove the electrodes from the sealed

package. Separate and straighten the

leadwires.

Remove the ﬁrst electrode from the

liner.

Place the electrode on the patient and

use gentle pressure to ensure contact

of the entire electrode surface to the

skin.

Repeat for each electrode.

Connect the leadwires

to the cable yoke.

Remove a DIN plug from the

disposable holder and plug it into the

corresponding color on the cable yoke.

Repeat for each DIN plug.

™

Red Dot

™

Pre-wired Monitoring Electrodes

See Removal instructions on back.

3M Health Care JOB #03R1005 TRIM SIZE =4.25” x 11”

Red Dot Appl/Remove Card COLOR: 4/C Process BLEED = +.125”

Source ﬁle in InDesign / Output ﬁle at 100% / Use fonts provided

Please recycle. Printed in U.S.A.

3M and Red Dot are trademarks of 3M.

70-2010-7553-1

3M Health Care

Infection Prevention Division

3M Center, Building 275-4E-02

St. Paul, MN 55144-1000

USA

1-800-228-3957

www.3M.com/infectionprevention

Removal Instructions

Loosen one side of the electrode.

Grasping the full width of the electrode,

slowly and gently pull it back over itself.

Electrodes should be removed in the

direction of hair growth whenever

possible. Keep the electrode close to

the skin surface as you pull it back, and

support the skin immediately adjacent

to the adhesive being removed.

To remove the DIN plug from the cable

yoke, grasp the plug ﬁrmly and pull.

Repeat for each DIN plug.

DO NOT remove the DIN plugs from

the cable by pulling on the wires.

All 3M Red Dot Monitoring Electrodes

are backed with a guarantee that’s

“Good as Gold.” If, for any reason,

you are dissatisﬁed with 3M Red Dot

Monitoring Electrodes, we will replace

the unexpired/unused product or, if

you prefer, refund the purchase price.

To learn more about 3M Red Dot Electrodes, call the 3M Health Care

Helpline at 1-800-228-3957 or visit www.3M.com/reddotelectrodes.

™

Red Dot

™

Pre-wired Monitoring Electrodes

3M Red Dot™ Neonatal, Pre-Wired, Radiolucent Monitoring Electrode Operating instructions

Brand: 3M

Model: Red Dot™ Neonatal, Pre-Wired, Radiolucent Monitoring Electrode

Type: Operating instructions

This manual is also suitable for

Red Dot™ ECG Monitoring Electrodes, Infant, Pre-Wired, Radiolucent, 2283

Download PDF

report

3M Red Dot™ Neonatal, Pre-Wired, Radiolucent Monitoring Electrode Operating instructions

This manual is also suitable for

3M Red Dot™ Neonatal, Pre-Wired, Radiolucent Monitoring Electrode Operating instructions

Related papers

Other documents