Sharp HTSB32D Owner's manual

Sharp
Brand
Sharp
Model
HTSB32D
Type
Owner's manual

This manual is also suitable for

Remote control battery installation
TINSEA348AWZZ
MODEL
HT-SB32D
SOUND BAR HOME THEATRE SYSTEM
This Quick Start Guide will help you to correctly install and operate your system.
Remote control × 1
RCA cable
(2 pins - 2 pins) × 1
AC power lead × 1 Foot cushion × 4
AC/DC adaptor × 1 Wall mount angle × 2
Nut
(Spike + Nut) × 4
(Length: 25 mm)
Pattern paper × 1
Accessories
Turn on your system
Before using remote control
Before using remote control, please remove plastic
shield at battery holder.
Battery holder
Plastic shield
Remote control
1 Press the ON/STAND-BY button.
The sound mode indicator and display light up. If the
power does not turn on, check whether the power
cord is plugged in properly.
2 To set the unit to stand-by mode:
Press the ON/STAND-BY button again.
The STAND-BY indicator turns red.
Polarity (+) symbol
Printed in Malaysia
11A R AS 1
1 Insert pin into the hole as shown and pull to open the
battery holder.
Battery holder
Locking tab
Battery type
Positive (+) side up
2 Remove the old battery from the battery holder,
insert the new battery and then slide the battery
holder back into the remote control.
Back of remote
control
Pin
HT-SB250W250BK (QG).indd 1 12/29/2010 5:07:22 PM
Accessories
MUTE
O
N/
STA
ND
-
B
Y
MU
SICCI
NEM
A NE
WS
SUR
ROU
ND
BYPA
SS
INPU
T
TV
CHVOL
VOL
RRMCG
A
322A
W
S
A
SOU
ND M
ODE
Remote control x 1 AC/DC adaptor x 1
(RADPA100AWZZ)
Optical cable x 1 Pattern paper x 1
Velcro tape (hook type) x 1 Velcro tape (loop type) x 2
HT-SB32D
AC power lead x 1 NFC tag x 1
Spike leg x 2
Before using remote control
Before using the remote control, remove the
plastic shield from the battery holder.
Remote control
Plastic shield
Battery holder
Turn on your system
Press the ON/STANDBY button.
The On/Standby/Input indicator lights up according to input
source:
Input source On/Standby/Input
indicator
OPTICAL IN Turns green
AUDIO IN Turns cyan
Bluetooth Turns blue
Note:
If the power does not turn on, check whether the power lead is
plugged in properly.
To set the sound bar to standby mode:
Press the ON/STANDBY button again. The PAIRING indicator
turns BLUE.
AC power connection
1 Plug the AC power lead into the AC/DC
adaptor.
2 Plug the AC/DC adaptor cable into the DC
INPUT socket on the sound bar.
3 Plug the AC power lead into a wall socket. The
PAIRING indicator turns BLUE.
14G R AS
1
TINSEA474AWZZ
B
arcodesof
t
http://www.barcodesoft.com
Barcode Symbology:
Code 93
; Font Facename:
Code93
M
H
r
Data To Encode:
TINSEA474AWZZ
Point Size 8 :
*TINSEA474AWZZI3*|
Point Size 10 :
*TINSEA474AWZZI3*|
Point Size 12 :
*TINSEA474AWZZI3*|
Point Size 14 :
*TINSEA474AWZZI3*|
Make sure to unplug the AC power lead before
making any connections.
2
1
AC/DC Adaptor
Cable
DC IN socket
(DC 19V)
AC power lead
AC/DC Adaptor
(AC 100 - 240 V ~ 50/60 Hz)
Wall socket
HTSB32_QG.indd 1 2014-07-07 08:56:37
To mount the sound bar on the wall
1 Fix the pattern paper to the wall in horizontal
position as below.
44 mm
509 mm
Wall
surface
Pattern paper
(supplied)
548 mm
2 Make a hole on the wall following the screw point
marks on the pattern paper by using a drill.
Wall surface
32 mm
8-9 mm
3 Fix a wall mount plug into the hole using a ham-
mer, until it is ush with the wall surface.
32 mm
8-9 mm
Wall surface
4 Fasten the screws to the wall as shown below.
(Total screw is 2 pieces)
Screw using
Wall surface
Wall surface
Screwdriver
4.5 mm - 5 mm
Gap from wall surface
5 Hang the sound bar onto the screws.
System preparation
1 Peel the double sided tape separator. 2 Fix the spike leg onto the sound bar as shown.
Make sure to unplug the AC power lead before installing the sound bar or changing the position.
Spike leg
Double sided
tape separator
Bottom of
sound bar
HTSB32_QG.indd 2 2014-07-07 08:56:38
  • Page 1 1
  • Page 2 2

Sharp HTSB32D Owner's manual

Sharp
Brand
Sharp
Model
HTSB32D
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents