Facom V.96F Owner's manual

Category
Power tools
Type
Owner's manual
WARNING
IMPORTANT SAFETY INFORMATION ENCLOSED.
READ THIS MANUAL BEFORE OPERATING TOOL.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE INFORMATION IN THIS MANUAL INTO THE HANDS OF THE OPERATOR.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
EN
PLACING TOOL IN SERVICE
• Always operate, inspect and maintain this tool in accordance
with all regulations (local, state, federal and country), that may
apply to hand held/hand operated pneumatic tools.
• For safety, top performance, and maximum durability of parts,
operate this tool at 90 psig (6.2 bar/620 kPa) maximum air
pressure at the inlet with 3/8” (10 mm) inside diameter air
supply hose.
• Always turn off the air supply and disconnect the air supply
hose before installing, removing or adjusting any accessory on
this tool, or before performing any maintenance on this tool.
• Do not use damaged, frayed or deteriorated air hoses and
ttings.
• Be sure all hoses and ttings are the correct size and are tightly
secured.
• Always use clean, dry air at 90 psig maximum air pressure.
Dust, corrosive fumes and/or excessive moisture can ruin the
motor of an air tool.
• Do not lubricate tools with ammable or volatile liquids such as
kerosene, diesel or jet fuel.
• Do not remove any labels. Replace any damaged label.
• The use of a hose whip is recommended. A coupler connected
directly to the air inlet increases tool bulk and decreases tool
maneuverability.
• For maximum performance, the coupler on the wall should be
the next size larger than the coupler used on the tool. The coupler
closest to the tool should not be less than the proper air supply
hose size.
NOTICE
The use of other than genuine FACOM replacement parts may result in safety hazards, decreased tool performance, and increased
maintenance, and may invalidate all warranties.
Repairs should be made only by authorized trained personnel. Consult your nearest FACOM Authorized Servicenter.
USING THE TOOL
• Always wear eye protection when operating or performing
maintenance on this tool.
• Always wear hearing protection when operating this tool.
• Keep hands, loose clothing and long hair away from rotating
end of tool.
• Anticipate and be alert for sudden changes in motion during
start up and operation of any power tool.
• Keep body stance balanced and rm. Do not overreach when
operating this tool. High reaction torques can occur at or below
the recommended air pressure.
• Air powered tools can vibrate in use. Vibration, repetitive mo-
tions or uncomfortable positions may be harmful to your hands
and arms. Stop using any tool if discomfort, tingling feeling or
pain occurs. Seek medical advice before resuming use.
• Use accessories recommended by FACOM.
• This tool is not designed for working in explosive atmospheres.
• This tool is not insulated against electric shock.
WARNING
WARNING LABEL IDENTIFICATION
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
WARNING
Always wear eye protection when operating or
performing maintenance on this tool.
WARNING
Always wear hearing protection when operating
this tool.
WARNING
Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions may be
harmful to your hands and arms. Stop using any tool if
discomfort, tingling feeling or pain occurs.
Seek medical advice before resuming use.
WARNING
Do not carry the tool by the hose.
WARNING
Keep body stance balanced and rm. Do not overreach
when operating this tool.
WARNING
Always turn off the air supply and disconnect the air
supply hose before installing, removing or adjusting
any accessory on this tool, or before performing any
maintenance on this tool.
WARNING
Operate at 90 psig (6.2 bar/ 620 kPa) Maximum air
pressure.
WARNING
Do not use damaged, frayed or deteriorated air hoses
and ttings.
LUBRICATION
FACOM NS.557
Always use of an air line lubricator with these tools. We recommended the
following Filter-Lubricator-Regulator Unit: FACOM N.553D.
After each eight hours operation, unless the air line lubricator is used, detach
the air hose and inject about 1-1/2 cc of oil into the inlet busching.
After each forty-eight hours of operation, or as experience indicates, remove
the Oil Chamber Plug and ll the mechanism oil chamber with the recommen-
ded oil FACOM NS.557.
PLACING TOOL IN SERVICE
En France, pour tous renseignements techniques sur l'outillage à main, téléphonez au : 01 64 54 45 14
BELGIQUE
LUXEMBOURG
FACOM Belgique S.A/NV
Weihoek 4
1930 Zaventem
BELGIQUE
: (02) 714 09 00
Fax : (02) 721 24 11
NEDERLAND
FACOM Gereedschappen BV
Kamerlingh Onnesweg 2
Postbus 134
4130 EC Vianen
NEDERLAND
: (0347) 362 362
Fax : (0347) 376 020
DANMARK
FINLAND
ISLAND
NORGE
SVERIGE
FACOM NORDEN
Nordre Strandvej 119B
3150 HELLEBÆK
DENMARK
: (45) 22 17 08 00
Fax : (45)
SINGAPORE
FAR EAST
FACOM TOOLS FAR EAST
N° 25 Senoko South Road
Woodlands East Industrial Estate
Singapore 758081
SINGAPORE
: (65) 6752 2001
Fax : (65) 6752 2697
DEUTSCHLAND
FACOM GmbH
Otto-Hahn-Straße 9
42369 Wuppertal
DEUTSCHLAND
: +49 202 69 819-329
Fax : +49 202 69 819-350
SUISSE
ÖSTERREICH
MAGYARORSZAG
CESKA REP.
FACOM OUTILLAGE SARL
Ringstrasse 14
8600 DÜBENDORF
SUISSE
: 41 44 802 8093
Fax : 41 44 802 8091
ESPAÑA
PORTUGAL
FACOM Herramientas SRL
Poligono industrial de Vallecas
C/Luis 1°, s/n-Nave 95 - 2°Pl.
28031 Madrid
ESPAÑA
: (91) 778 21 13
Fax : (91) 380 65 33
UNITED
KINGDOM
EIRE
FACOM-UK
Europa view
SHEFFIELD BUSINESS PARK
UNITED KINGDOM
: (44) 114 244 8883
Fax : (44) 114 273 9038
ITALIA
Utensilerie Associate srl.
Via Volta 3
21020 Monvalle (VA)
ITALIA
: (0332) 790 381
Fax : (0332) 790 307
POLSKA
FACOM Tools Polska Sp. zo.o.
ul.Modlińska 190
03-119 Warszawa
POLSKA
: (00 48 22) 510 36 55
Fax : (00 48 22) 510 36 56
FRANCE
&
INTERNATIONAL
Société FACOM
6-8, rue Gustave Eiffel B.P.99
91423 Morangis cedex
FRANCE
: 01 64 54 45 45
Fax : 01 69 09 60 93
http:/ /www.facom.fr
Europa link
SHEFFIELD
1 / 1

Facom V.96F Owner's manual

Category
Power tools
Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Ask the document