Gateway MT6729 Hardware Replacement Manual

Brand: Gateway

Model: MT6729

Category: Notebook accessories

Type: Hardware Replacement Manual

Replacing the AC Adapter

Technical Support

See the label on the bottom of the notebook for Customer Care Information. See

your reference guide for important safety, regulatory, and legal information.

or registered trademarks of Gateway, Inc. in the United States and other countries.

All other brands and product names are trademarks or registered trademarks of

their respective companies.

Replacing the AC Adapter

To connect the AC adapter:

1 Connect the power cord to the AC adapter.

2 Connect the AC adapter to your notebook’s power connector.

3 Plug the power cord into an AC power outlet. The power indicator

turns on.

If the battery charge indicator does not turn on:

• Unplug the adapter from your notebook, then plug it back in.

•Press F

N+F1 to toggle the status lights on and off.

• Make sure the power cord is firmly attached to the AC

adapter.

• Plug the power cord into a different wall outlet.

Caution

Replace the power cord if it becomes damaged. The replacement cord

must be of the same type and voltage rating as the original cord or your

notebook may be damaged.

Warning

Do not attempt to disassemble the AC adapter. The AC adapter has

no user-replaceable or user-serviceable parts inside. The AC adapter has

dangerous voltages that can cause serious injury or death. Contact Gateway

about returning defective AC adapters.

Important

If the battery charge indicator does not turn blue after three hours,

contact Gateway Customer Care at the Web address or telephone number

shown on the label on the bottom of your notebook.

Power indicator

Replacing the Battery

Technical Support

See the label on the bottom of the notebook for Customer Care Information. See

your reference guide for important safety, regulatory, and legal information.

or registered trademarks of Gateway, Inc. in the United States and other countries.

All other brands and product names are trademarks or registered trademarks of

their respective companies.

Replacing the Battery

Locating Components

To replace the battery:

1 If your notebook is on and is connected to AC power, go to Step 2.

- OR -

If your notebook is on and is not connected to AC power, save

your work and turn off your notebook.

2 Close the LCD panel.

3 Turn your notebook over so the bottom is facing up.

4 Slide the battery lock to the unlock position.

5 Slide the battery release latch, then slide the battery out of the

notebook.

6 Slide the replacement battery into the notebook until it snaps into

place.

7 Slide the battery lock to the lock position.

8 Turn your notebook over.

9 Plug your notebook into an AC outlet.

10 Open the LCD panel and press the power button.

Important

If your notebook is connected to AC power, you can replace the

battery while the notebook is turned on.

Warning

Danger of explosion if the battery is incorrectly replaced.

Replace only with a battery specifically manufactured for your notebook.

Recycle or dispose of the battery as hazardous waste.

The battery used in this device may present a fire or chemical burn hazard

if mishandled. Do not disassemble, heat above 212°F (100°C), or incinerate.

Keep away from children.

Battery

Important

If the battery charge indicator does not turn blue after three hours,

contact Gateway Customer Care at the Web address or telephone number

shown on the label on the bottom of your notebook.

Replacing the DVD Drive

Technical Support

See the label on the bottom of the notebook for Customer Care Information. See

your reference guide for important safety, regulatory, and legal information.

or registered trademarks of Gateway, Inc. in the United States and other countries.

All other brands and product names are trademarks or registered trademarks of

their respective companies.

Replacing the DVD Drive

Preventing static electricity discharge

The components inside your notebook are extremely sensitive to static

electricity, also known as electrostatic discharge (ESD). ESD can

permanently damage electrostatic discharge-sensitive components in

your notebook.

Before working with notebook components, follow these guidelines:

• Avoid static-causing surfaces such as carpeted floors, plastic, and

packing foam.

• Remove components from their antistatic bags only when you are

ready to use them. Do not lay components on the outside of

antistatic bags because only the inside of the bags provide

electrostatic protection.

• Always hold components by their edges. Avoid touching the edge

connectors. Never slide components over any surface.

• Wear a grounding wrist strap (available at most electronics stores)

and attach it to a bare metal part of your workbench or other

grounded connection.

• Touch a bare metal surface on your workbench or other grounded

object.

Replacing the DVD drive

To replace the DVD drive:

1 Follow the guidelines under “Preventing static electricity

discharge.”

2 Make sure that the DVD drive is empty.

3 Turn off your notebook.

4 Close the LCD panel.

5 Disconnect the AC adapter, modem cable, and network cable.

6 Disconnect all peripheral devices and remove any Express, PC,

and memory cards.

7 Turn your notebook over so the bottom is facing up, then remove

the battery. For more information, see “Changing Batteries” in

your Reference Guide.

8 With a small Phillips screwdriver, remove the keyboard screw and

put it in a safe place.

9 Loosen the six memory bay cover screws (these screws cannot

be removed), then remove the memory bay cover.

10 With a small Phillips screwdriver, remove the DVD drive screw,

then put it in a safe place.

Tools

You need a small Phillips screwdriver to replace the DVD drive.

Warning

To avoid exposure to dangerous electrical voltages and moving parts,

turn off your notebook and unplug the AC adapter, modem cable, and

network cable and remove the battery before replacing a component.

Important

The keyboard screw hole is marked with a K.

Screw

Replacing the DVD Drive

Technical Support

See the label on the bottom of the notebook for Customer Care Information. See

your reference guide for important safety, regulatory, and legal information.

or registered trademarks of Gateway, Inc. in the United States and other countries.

All other brands and product names are trademarks or registered trademarks of

their respective companies.

11 Slide the DVD drive out of the drive bay by pushing on the DVD

bracket.

12 Slide the new DVD drive into the drive bay. Make sure that the

drive fits securely in the bay.

13 Secure the DVD drive with the screw removed in Step 10.

14 Replace the memory bay cover, then tighten the six cover screws.

15 Replace the keyboard screw.

16 Insert the battery, then turn your notebook over.

17 Connect the power adapter, modem cable, and network cable,

then turn on your notebook.

18 Reconnect all peripheral devices and replace any Express, PC, or

memory cards.

DVD bracket

Replacing the Hard Drive Kit

Technical Support

See the label on the bottom of the notebook for Customer Care Information. See

your reference guide for important safety, regulatory, and legal information.

or registered trademarks of Gateway, Inc. in the United States and other countries.

All other brands and product names are trademarks or registered trademarks of

their respective companies.

Replacing the Hard Drive Kit

Locating Components

Preventing static electricity discharge

The components inside your notebook are extremely sensitive to static

electricity, also known as electrostatic discharge (ESD). ESD can

permanently damage electrostatic discharge-sensitive components in

your notebook.

Before working with notebook components, follow these guidelines:

• Avoid static-causing surfaces such as carpeted floors, plastic, and

packing foam.

• Remove components from their antistatic bags only when you are

ready to use them. Do not lay components on the outside of

antistatic bags because only the inside of the bags provide

electrostatic protection.

• Always hold components by their edges. Avoid touching the edge

connectors. Never slide components over any surface.

• Wear a grounding wrist strap (available at most electronics stores)

and attach it to a bare metal part of your workbench or other

grounded connection.

• Touch a bare metal surface on your workbench or other grounded

object.

Replacing the hard drive kit

To replace the hard drive kit:

1 If possible, create a Drivers and Applications Recovery disc. For

more information, see “Preparing for software and device driver

recovery” in the Reference Guide.

2 Follow the guidelines under “Preventing static electricity

discharge.”

3 Turn off your notebook.

4 Disconnect the AC adapter, modem cable, and network cable.

5 Disconnect all peripheral devices and remove any Express, PC,

and memory cards.

6 Turn your notebook over so the bottom is facing up, then remove

the battery. For more information, see “Changing Batteries” in

your Reference Guide.

7 Remove the two hard drive bay cover screws, slide the hard drive

bay cover, then remove it. The hard drive is attached to the back

of the cover.

8 Remove the four screws that secure the hard drive to the hard

drive cover.

9 Remove the cover from the old drive.

10 Place the new drive, label side up, onto the cover so the screw

holes line up.

11 Replace the four screws that secure the cover to the drive.

12 Slide the new hard drive kit into your notebook, then replace the

cover screws.

Tools

You need a small Phillips screwdriver to replace the hard drive.

You may need the operating system disc that came with your

notebook.

Warning

To avoid exposure to dangerous electrical voltages and moving parts,

turn off your notebook and unplug the AC adapter, modem cable, and

network cable and remove the battery before replacing a component.

Important

If you cannot create a Drivers and Applications Recovery disc,

Gateway may send you a set of recovery discs or a replacement hard drive

with the drivers and applications already installed. Contact Gateway

Customer Care at the Web address or telephone number shown on the label

on the bottom of your notebook.

Hard

drive

bay

Screws

Screws Screws

Replacing the Hard Drive Kit

Technical Support

See the label on the bottom of the notebook for Customer Care Information. See

your reference guide for important safety, regulatory, and legal information.

or registered trademarks of Gateway, Inc. in the United States and other countries.

All other brands and product names are trademarks or registered trademarks of

their respective companies.

13 Insert the battery, then turn your notebook over.

14 Connect the power adapter, modem cable, and network cable.

15 Turn on your notebook.

16 If the hard drive was sent to you from Gateway with the operating

system, applications, and drivers installed, you will see the

Windows startup screen. Go to Step 18.

-OR-

If you see a blank screen, insert the Windows DVD into your

notebook’s DVD drive, then restart your notebook.

17 Follow the on-screen instructions. As part of the process, you may

be prompted to insert your Drivers and Applications Recovery

disc.

18 Reconnect all peripheral devices and replace any Express, PC, and

memory cards.

Replacing the Keyboard

Technical Support

See the label on the bottom of the notebook for Customer Care Information. See

your reference guide for important safety, regulatory, and legal information.

or registered trademarks of Gateway, Inc. in the United States and other countries.

All other brands and product names are trademarks or registered trademarks of

their respective companies.

Replacing the Keyboard

Preventing static electricity discharge

The components inside your notebook are extremely sensitive to static

electricity, also known as electrostatic discharge (ESD). ESD can

permanently damage electrostatic discharge-sensitive components in

your notebook.

Before working with notebook components, follow these guidelines:

• Avoid static-causing surfaces such as carpeted floors, plastic, and

packing foam.

• Remove components from their antistatic bags only when you are

ready to use them. Do not lay components on the outside of

antistatic bags because only the inside of the bags provide

electrostatic protection.

• Always hold components by their edges. Avoid touching the edge

connectors. Never slide components over any surface.

• Wear a grounding wrist strap (available at most electronics stores)

and attach it to a bare metal part of your workbench or other

grounded connection.

• Touch a bare metal surface on your workbench or other grounded

object.

Removing the old keyboard

To remove the old keyboard:

1 Follow the guidelines under “Preventing static electricity

discharge.”

2 Turn off your notebook.

3 Close the LCD panel.

4 Disconnect the AC adapter, modem cable, and network cable.

5 Disconnect all peripheral devices and remove any Express, PC,

and memory cards.

6 Turn your notebook over so the bottom is facing up, then remove

the battery. For more information, see “Changing Batteries” in

your Reference Guide.

7 Remove the two keyboard screws and put them in a safe place.

8 Loosen the six memory bay cover screws (these screws cannot

be removed), then remove the bay cover.

9 If your notebook has the optional keyboard screw as shown,

remove it.

10 Turn your notebook over so the top is facing up.

11 With a small Phillips screwdriver, remove the two hinge cover

screws and put them in a safe place.

Tools

You need a small Phillips and a small flat-blade screwdriver to replace

the keyboard.

Warning

To avoid exposure to dangerous electrical voltages and moving parts,

turn off your notebook and unplug the AC adapter, modem cable, and

network cable and remove the battery before replacing a component.

Important

The keyboard screw holes are marked with a K.

Keyboard screw

Screw

Replacing the Keyboard

Technical Support

See the label on the bottom of the notebook for Customer Care Information. See

your reference guide for important safety, regulatory, and legal information.

or registered trademarks of Gateway, Inc. in the United States and other countries.

All other brands and product names are trademarks or registered trademarks of

their respective companies.

12 Insert the small flat-blade screwdriver under the bottom of each

hinge cover and gently pry them up.

13 Carefully open the LCD panel to the fully opened position.

14 Insert the small flat-blade screwdriver under the right hinge cover

and gently pry it up. The hinge cover is part of the keyboard

cover.

15 Pull the keyboard cover off the notebook. Be careful to not

damage the LCD panel.

16 Lift the back edge of the keyboard slightly, then slowly slide it

toward the LCD panel to release the keyboard retaining tabs

located on the front of the keyboard.

17 Slowly rotate the keyboard toward you so it lies keys-down on

top of your notebook. Be careful to not damage the LCD panel.

18 Slide the black keyboard connector clip to the front of the

notebook and slide the cable out of the clip. Be careful not to

touch or damage any other components.

Installing the new keyboard

To install the new keyboard:

1 Place the new keyboard keys-down on your notebook with the

space bar away from you.

2 Make sure the black keyboard connector clip is fully moved

toward the front of the notebook, insert the cable into the

connector, then slide the black clip to lock the connector in place.

3 Rotate the keyboard toward the LCD panel until the keyboard is

almost face-up.

4 Insert the tabs on the front edge of the keyboard into the slots

under the palm rest. You may need to press down on the

keyboard keys along the front edge of the keyboard to seat the

retaining tabs into their corresponding slots.

5 Gently press the keyboard down until it is flat all the way across.

The keyboard should easily fall into place. Be careful to not

damage the LCD panel.

6 Replace the keyboard cover. Press down on the cover in several

places until it clicks in place. The cover is correctly mounted when

you can run you finger along the cover and find no loose spots.

The cover should be flat all the way across.

7 Close the LCD panel, then replace the two hinge cover screws.

8 Turn your notebook over so the bottom is facing up.

9 Replace the optional keyboard screw.

10 Replace the memory bay cover.

11 Replace the keyboard screw.

12 Insert the battery, then turn your notebook over.

13 Connect the power adapter, the modem cable, and the network

cable, then turn on your notebook.

14 Reconnect all peripheral devices and replace any Express, PC, and

memory cards.

Connector

Important

The keyboard cable is correctly oriented if it is not twisted.

Caution

If the cover is not correctly replaced, your notebook could be

damaged when you try to close the LCD panel.

Replacing the Memory Module

Technical Support

See the label on the bottom of the notebook for Customer Care Information. See

your reference guide for important safety, regulatory, and legal information.

or registered trademarks of Gateway, Inc. in the United States and other countries.

All other brands and product names are trademarks or registered trademarks of

their respective companies.

Replacing the Memory

Module

Locating Components

Preventing static electricity discharge

The components inside your notebook are extremely sensitive to static

electricity, also known as electrostatic discharge (ESD). ESD can

permanently damage electrostatic discharge-sensitive components in

your notebook.

Before working with notebook components, follow these guidelines:

• Avoid static-causing surfaces such as carpeted floors, plastic, and

packing foam.

• Remove components from their antistatic bags only when you are

ready to use them. Do not lay components on the outside of

antistatic bags because only the inside of the bags provide

electrostatic protection.

• Always hold components by their edges. Avoid touching the edge

connectors. Never slide components over any surface.

• Wear a grounding wrist strap (available at most electronics stores)

and attach it to a bare metal part of your workbench or other

grounded connection.

• Touch a bare metal surface on your workbench or other grounded

object.

Replacing the memory module

To replace the memory module:

1 Follow the guidelines under “Preventing static electricity

discharge.”

2 Turn off your notebook.

3 Close the LCD panel.

4 Disconnect the AC adapter, modem cable, and network cable.

5 Disconnect all peripheral devices and remove any Express, PC,

and memory cards.

6 Turn your notebook over so the bottom is facing up, then remove

the battery. For more information, see “Changing Batteries” in

your Reference Guide.

7 With a small Phillips screwdriver, remove the keyboard screw and

put it in a safe place.

8 Loosen the six memory bay cover screws (these screws cannot

be removed), then remove the memory bay cover.

9 If you are removing a memory module, gently press outward on

the clip at each end of the module until the module tilts upward.

Tools

You need a small Phillips screwdriver to replace the memory module.

Warning

To avoid exposure to dangerous electrical voltages and moving parts,

turn off your notebook and unplug the AC adapter, modem cable, and

network cable and remove the battery before replacing a component.

Memory

bay

Important

The keyboard screw hole is marked with a K.

Screw

Replacing the Memory Module

Technical Support

See the label on the bottom of the notebook for Customer Care Information. See

your reference guide for important safety, regulatory, and legal information.

or registered trademarks of Gateway, Inc. in the United States and other countries.

All other brands and product names are trademarks or registered trademarks of

their respective companies.

10 Pull the memory module out of the slot. 11 Hold the new or replacement module at a 30-degree angle and

insert it into the empty memory slot. This module is keyed so it

can only be inserted in one direction. If the module does not fit,

make sure that the notch in the module lines up with the tab in

the memory bay.

12 Gently push the module down until it clicks in place.

13 Replace the memory bay cover, then tighten the six cover screws.

14 Replace the keyboard screw.

15 Insert the battery, then turn your notebook over.

16 Connect the power adapter, the modem cable, and the network

cable.

17 Reconnect all peripheral devices and replace any Express, PC, or

memory cards.

18 Turn on your notebook.

Important

Use only memory modules designed for your Gateway notebook.

Replacing the Wireless Network Module

Technical Support

See the label on the bottom of the notebook for Customer Care Information. See

your reference guide for important safety, regulatory, and legal information.

or registered trademarks of Gateway, Inc. in the United States and other countries.

All other brands and product names are trademarks or registered trademarks of

their respective companies.

Replacing the Wireless

Network Module

Locating Components

Preventing static electricity discharge

The components inside your notebook are extremely sensitive to static

electricity, also known as electrostatic discharge (ESD). ESD can

permanently damage electrostatic discharge-sensitive components in

your notebook.

Before working with notebook components, follow these guidelines:

• Avoid static-causing surfaces such as carpeted floors, plastic, and

packing foam.

• Remove components from their antistatic bags only when you are

ready to use them. Do not lay components on the outside of

antistatic bags because only the inside of the bags provide

electrostatic protection.

• Always hold components by their edges. Avoid touching the edge

connectors. Never slide components over any surface.

• Wear a grounding wrist strap (available at most electronics stores)

and attach it to a bare metal part of your workbench or other

grounded connection.

• Touch a bare metal surface on your workbench or other grounded

object.

Replacing the wireless network module

To replace the wireless network module:

1 Follow the guidelines under “Preventing static electricity

discharge.”

2 Turn off your notebook.

3 Close the LCD panel.

4 Disconnect the AC adapter, modem cable, and network cable.

5 Disconnect all peripheral devices and remove any Express, PC,

and memory cards.

6 Turn your notebook over so the bottom is facing up, then remove

the battery. For more information, see “Changing Batteries” in

your Reference Guide.

7 Loosen the wireless network bay cover screw (this screw cannot

be removed), then remove the wireless network bay cover.

8 Unplug the antenna cables. Note which color cable is connected

to each antenna connector.

9 Move the antenna cables out of the way.

Caution

By law, only approved wireless modules provided by Gateway or a

Gateway authorized representative, explicitly for your notebook, may be

installed in this notebook.

Tools

You need a small Phillips screwdriver to replace the wireless network

module.

Warning

To avoid exposure to dangerous electrical voltages and moving parts,

turn off your notebook and unplug the AC adapter, modem cable, and

network cable and remove the battery before replacing a component.

Wireless

network

bay

Screw

Replacing the Wireless Network Module

Technical Support

See the label on the bottom of the notebook for Customer Care Information. See

your reference guide for important safety, regulatory, and legal information.

or registered trademarks of Gateway, Inc. in the United States and other countries.

All other brands and product names are trademarks or registered trademarks of

their respective companies.

10 Remove the screw securing the wireless network module.

11 Pull the module out of the slot.

12 Hold the new module at a 30-degree angle and insert it into the

empty slot. This module is keyed so it can only be inserted in one

direction. If the module does not fit, make sure that the notch in

the module lines up with the tab in the module slot.

13 Move the antenna wires out of the way.

14 Replace the screw removed in Step 10.

15 Reattach the antenna cables to the corresponding connectors.

16 Replace the wireless network bay cover, then tighten the cover

screw.

17 Insert the battery, then turn your notebook over.

18 Connect the power adapter, the modem cable, and the network

cable.

19 Reconnect all peripheral devices and replace any Express, PC, and

memory cards.

20 Turn on your notebook.

Screw

Gateway MT6729 Hardware Replacement Manual

Brand: Gateway

Model: MT6729

Category: Notebook accessories

Type: Hardware Replacement Manual

Download PDF

report

Gateway MT6729 Hardware Replacement Manual

Gateway MT6729 Hardware Replacement Manual

Related papers

Other documents