Proteus PEC-1900 Series Owner's manual

Brand: Proteus

Model: PEC-1900 Series

Category: Fitness, gymnastics & weight training

Type: Owner's manual

Owner's manual

PEC 1900 SERIES

MAGNETIC CYCLE

PEC-1900 SERIES HOME MAGNETIC CYCLE ASSEMBLY INSTRUCTION

Important safety precautions

1. Read the owner's manual and all accompanying literature and follow it carefully before using

your machine.

2. This machine is intended for household use only. It is not designed for commercial use.

3. Inspect your exercise machine prior to exercising to ensure that all nuts and bolts are fully

tightened before each use.

4. Make sure machine is stabilized on the floor and uneven surfaces are leveled before use.

5. Most exercise equipment is not recommended for small children. Children should not use the

machine unless they are under adult supervision.

6. Exercise equipment has moving parts. In the interest of safety, keep others, especially children,

at a safe distance while exercising.

7. Make sure all adjustment devices are fully inserted and properly adjusted before use to avoid

injury.

8. Remove all jewelry, including rings, chains and pins before commencing exercise.

9. Always wear suitable clothing and footwear during exercise. Do not wear loose fitting clothing

that could become entangled with the moving parts of your exercise machine.

10. Warm up 5 to 10 minutes before each workout and cool down 5 to 10 minutes afterward. This

allows your heart rate to gradually increase and decrease and will help prevent straining

muscles.

11. Never hold your breath while exercising. Breathing should remain at a normal rate in

conjunction with the level of exercise being performed.

12. Rest adequately between workouts. Muscles tone and develop during these rest periods.

Beginners should work out twice a week and increase gradually to 4 or 5 times per week.

13. Do not "over train". Incorrect or excessive training may result in injury.

- 1 -

NOTE : THE EQUIPMENT IS SPEED-DEPENDENT ON BRAKING SYSTEM.

IMPORTANT : THE MAXIMUM RECOMMENDED WEIGHT CAPACITY FOR

YOUR EQUIPMENT IS 110 KG ( 240 LB ) PER USER.

- 1 -

THIS OWNER'S MANUAL CONTAINS ASSEMBLY, OPERATION, MAINTENANCE AND

SAFETY INFORMATION. IN THE INTEREST OF SAFETY, PLEASE MAKE CERTAIN

THAT YOU READ AND UNDERSTAND ALL THE INFORMATION BELOW.

Warning : Before commencing with any exercise program, please consult your family physician. If

at any time during exercise you feel faint, dizzy or experience pain, stop and consult

your family physician. In the event any of the above mentioned warnings are breached

by the consumer, the manufacturer may use same as a defense to any claim for

injuries, damage or loss. The above warnings are in no way intended to limit or modify

the consumer's remedies for breach of warranties pursuant to applicable federal and

state laws of regulations. They are being supplied strictly to ensure the safety of the

individuals using this product.

The appliances are not for children under 14 years of ages.

Before you begin

Important : Read all instructions carefully. Assemble the unit in accordance with the steps in the

manual. Lay out all parts on the floor and check if you have all the parts included

completely before beginning assembly. In case of a discrepancy, please call the

customer service department of the store for help.

Note : Some parts may be factory pre-assembled.

Tools required for assembly

One adjustable wrench, a philips head screwdriver and a allen key

The safety level of the equipment can be maintained only if it is examined

regularly for damaged and wear.

The pedal crank training equipment of class b and c is not suitable for

therapeutic purposes.

Replaced defective components immediately and keep the equipment out of use until

repair.

The most susceptible to wear parts are

Drum magnetic wheel

Belt

B.B parts

- 2 -

- 3 -

MAGNETIC CYCLE ASSEMBLY INSTRUCTION

IMPORTANT : READ ALL STEPS BEFORE ATTACHING PEDALS

Step 1. Attach both front and rear stabilizers ( 2/3 ) to main frame ( 01 ), fix with carriage bolts

( 27 ) washers ( 30 ) and dome nuts ( 34 ).

Step 2.

a. Attach pedals ( 18 / 19 ) to pedal cranks, ( pedals marked "L" and "R" indicates left

and right side of bike. Make sure not to mix it up ).

b. Left pedal has left hand thread and must be turned counter- clockwise ( ccw ) to

attach, right pedal has right hand thread, must be turned clockwise ( cw ) to attach.

Step 3. Attach saddle ( 13 ) to saddle plate of seat post ( 04 ) fasten with spring washers ( 32 )

and nylon nuts ( 33 ).

Step 4. Attach seat post ( 04 ) to seat post support ( on main frame ), adjust saddle to desired

height and tighten with knob ( 14 ).

Step 5. Insert tension cable ( 10 ) inside of handle bar post ( 05 ), pull the tension cable out

from middle hole of handle bar post. Connect wire A ( 11 ) and wire B ( 12 ), then

attach handlebar post to main frame ( 01 ), fix with bolts ( 28 ) and washers ( 30 ).

Assemble tension control knob ( 09 ) and tension cable ( 10 ), by connecting cable head

( on knob ) to the draw hook of tension cable ( please refer to FIG. A & FIG. B ).

Assemble the tension control knob ( 09 ) onto handlebar post ( 05 ). Note the fix-hook

(on tension control ) well inserted onto handle bar post. Then tighten with screw ( 26 ).

Assemble handlebar & monitor

( 1 ) If your model no. is PEC-1900/1900EP/1905/1905EP/1925HP, please do step 6. &

step 7.

( 1 ) If your model no. is PEC-1900GP/1905GP/1935GP. please do step 8.

Step 6. Assemble foam grip ( 17 ) and end cap ( 16 ) onto one side of handlebar ( 06 ), then

attach handlebar ( 06 ) to handle bar post ( 05 ), tighten with washer ( 31 ) and T-knob

( 25 ). Assemble foam grip ( 17 ) and end cap ( 16 ) onto another side of handlebar

( 06 ).

Note : Use some soap water as lubricant while fitting foam grips.

Step 7. Assemble wire A ( 11 ) to monitor ( 08 ), then attach monitor on fixplate of handlebar

post.

MAGNETIC CYCLE ASSEMBLY INSTRUCTION

Step 8. a. Attach half moon bracket ( 38 ), handlebar ( 06 ) to handlebar post ( 05 ) and fix with

screw ( 37 ), T-knob ( 25 ) & washer ( 31 ). Do not overtighten the screw & T-knob

before the handlebar located in desired position. ( Please refers to FIG. C )

( Note To adjust angle of handlebar, by unscrewing T-knob then tighten it firmly. )

b. Insert the grip pulse wire ( 35 ) into the handlebar post and let it through the top of

monitor mounting plate.

c. Connecting wire A ( 11 ) & grip pulse wire ( 35 ) with monitor ( 08 ).

( Please refers to FIG. D )

d. Slide the monitor into mounting plate carefully.

**** Now your PEC-1900 series has been well assembled. ****

" THE BATTERIES MUST BE REMOVED FROM THE APPLIANCE BEFORE IT IS

SCRAPPED AND THAT THEY ARE DISPOSED OF SAFELY ".

- 4 -

- 5 -

EXPLODED VIEW

FIG. A

FIG. B

PEC-1935

KEY

ALLEN

PEC-1905 FIG.D

PEC-1905/1935 FIG.C

PEC-1900

PEC-1925

- 6 -

PARTS LIST

1. 1 Main frame

2. 1 Front stabilizer

3. 1 Rear stabilizer

4. 1 Seat post

5. 1 Handlebar post

6. 1 Handlebar

7. 1 Crank assembly

8. 1 Cyclemonitor

9. 1 Tension control

10. 1 Tension cable

11. 1 Wire ( A )

12. 1 Wire ( B )

13. 1 Saddle

14. 1 Knob

15. 1 60 sleeve

16. 2 Handlebar end cap

17. 2 Foam grip

18. 1 Pedal ( R )

19. 1 Pedal ( L )

20. 1 Chain cover ( R )

21. 1 Chain cover ( L )

22. 2 Crank hole cover

23. 2 Foot cap ( A )

24. 2 Foot cap ( B )

25. 1 T-knob

26. 1 M4 screw x 15mm

27. 4 M8 carrage bolt x 70mm

28. 3 M8 socket bolt x 15mm

30. 7 M8 washer

31. 1 M8 small washer

32. 3 M8 spring washer

33. 3 M8 nylon nut

34. 4 M8 dome nut

35. 1 Grip pulse wire

36. 2 Grip pulse

37. 1 M7 socket screw x 20mm

38. 1 Half-moon bracket

39. 2 M5 screw x 25mm

ey Q'ty Description

PEC1900SERIES-050221GB

Proteus PEC-1900 Series Owner's manual

Brand: Proteus

Model: PEC-1900 Series

Category: Fitness, gymnastics & weight training

Type: Owner's manual

Download PDF

report

Proteus PEC-1900 Series Owner's manual

Proteus PEC-1900 Series Owner's manual

Related papers

Other documents