Gaggia CLASSIC COFFEE User manual

EsPREsso

Instructions

Mode d’emploi

lnstrucciones de

us0

READ THIS FIRST!

For

GAGGIA~~~presso/Cappuccino

Makers

BEFORE making espresso the first time, you MUST prime the pump!

Here’s how to do it:

1. Plug the electrical cord into a live outlet.

2. Fill the water reservoir. (Filtered water is better.)

3. Place an empty filter into the black handled filter holder.

4. Attach the filter holder to the machine.

5. Turn on the power switch.

6. Allow the machine to heat up for 6 minutes.

7. Open the steam valve all the way.

8. Place an empty steam pitcher or mug under the steam tube.

9. Turn on the coffee switch and the steam switch.

10. Water will come out of the steam tube.

Il.

Allow about a cup of water to come out into the pitcher.

12. Turn off the coffee and steam switches.

13. Close the steam valve.

14. Place an empty cup under the coffee filter.

15. Turn on the “coffee” switch.

16. Fill the cup with water.

17. Turn off the “coffee” switch.

YOU ONLY NEED TO PRIME THE PUMP AGAIN ONLY IF NO WATER

COMES OUT OR THE PUMP IS MAKING TOO MUCH NOISE.

Now you are ready to make espresso!!! Here’s how:

Remove the black handled filter holder.

2. Using the measure provided, place one or two measures of finely

ground espresso coffee in the filter basket.

(The large filter holds two measures for two cups,

the small filter is for one cup.)

3. Using the tamper provided, gently press and twist the tamper on the

surface of the ground coffee to pack it down.

4. Brush off any grounds on the rim with the palm of your hand.

5. Attach the filter holder firmly to the machine.

6. Place empty cup (or cups) under the filter holder spouts.

7. Turn on the “coffee” switch.

8. The pump sound will change in a few seconds and espresso

will start to flow into the cups.

9. When the streams of espresso turn light in color,

TURN OFF the “coffee” switch.

10. You may now remove the cups of espresso and serve them.

11. Before making more espresso, remove the filter holder and

knock out the used grounds. DO NOT rinse the filter or filter holder at

this time as it will cool them and make the next batch taste bitter.

TO MAKE CAPPUCCINO

1. Turn on the steam switch.

2. Put cold milk (skim,

I%,

2%, Regular, Half

Half)

into a steaming pitcher only one-third full.

3. Place an empty mug under the steam tube and open the steam

valve part way to remove any accumulated water from the steam tube.

4. Close the steam valve.

5. Hold the pitcher with milk in it so that the end of the steam tube

is below the surface of the milk but not so deep to block the air intake.

6. Open the steam valve all the way.

7. As the froth forms, raise the pitcher so that the steam tube

goes deeper into the pitcher over the air intake.

8. When the froth is near the top of the pitcher, turn off the steam valve.

(the froth may not come to the top if you are using a large

pitcher with less milk in it.)

9. Turn off the “Steam” switch.

10. Remove the cups of espresso from the drip pan grid.

11. Spoon some froth from the pitcher on the espresso in the cup(s),

then pour the hot milk in until the froth reaches the top of the cup(s).

12. If desired, sprinkle shaved chocolate or cinamon on top of the froth.

IMPORTANT SAFEGUARDS

When using electrical appliances,

basic safety precautions should always

be followed to reduce the risk of fire,

electric shock, and/or injury to persons,

including the following:

_-’

Read all instructions and informa-

tion in this instruction book and any

other literature included in this

carton referring to this product

before operating or using this

appliance.

Do not touch hot surfaces. Use

handles or knobs.

To protect against fire, electric

shock and personal injury do not

immerse cord, plugs, or appliance

in water or other liquid.

Close supervision is necessary

when any appliance is used by or

near children,

Unplug from outlet when not in use

and before cleaning. Allow to cool

before putting on or taking off parts,

and before cleaning the appliance.

Do not operate any appliance with a

damaged cord or plug or after the

10.

11.

12.

13.

appliance malfunctions or has been

damaged in any manner. Return

appliance to the nearest authorized

service center for examination,

repair or adjustment.

The use of accessory attachments

not recommended by the appliance

manufacturer may result in fire,

electric shock or personal injury.

Do not use outdoors.

Do not let cord hang over edge of

table or counter, or touch hot

surfaces.

Do not place on or near a hot gas

or electric burner, or in a heated

oven.

Always turn appliance

“O”,

then

plug cord into the wall outlet. To

disconnect, turn switch to

‘IO”,

then

remove plug from wall outlet.

Do not use appliance for other than

intended household use.

Use

egtreme

caution when using hot

steam.

SAVE THESE INSTRUCTIONS.

CAUTION:

This appliance is for household use. Any servicing, other than cleaning and user

maintenance, should be performed by an authorized service center.

Do not immerse base in water.

To reduce the risk of fire or electric shock, do not disassemble the base. No user

serviceable parts inside. Repair should be done by authorized service personnel

only.

1. Check voltage to be sure that the voltage indicated on the name plate agrees

with your voltage.

2. Never use warm or hot water to fill the water reservoir. Use cold water only.

3. Keep your hands and the cord away from hot parts of the appliance during

operation.

4. Never clean with scouring powders or

hard,implements.

5. To avoid your machine scaling up, use purified’or bottled water.

Description of Parts:

On-Off switch

Power-on light

Hot water/brew switch (pump)

Temperature ready-light

Steam switch (temperature)

Reservoir cover

Removable water knob

Steam/hot water knob

Turbo frother steam nozzle

(remo-

veable)

Filterholder

9a.

Filter basket 1

cups

10.

Drip plate

1 Oa. Drip tray

11.

Brew head

1 la. Filterholder seal

11 b.

Showerholder

12.

Shower head

13.

Tamper

14. Power cable and plug

INSTRUCTIONS FOR THE POWER SUPPLY CORD

Regarding Your Cord Set:

A. A short power-supply cord is provided to reduce risks resulting from becoming

entangled in or tripping over a longer cord.

ONLY FOR TWO WIRES POWER SUPPLY CORD:

This appliance has a polarized plug (one blade is wider than the other).

As a safety feature, this plug will fit in a polarized outlet only one way.

If fhe plug does not fit fully in the outlet, reverse the plug. If it still does not fit,

contact a qualified electrician. Do not attempt to defeat the safety feature.

B. Longer extension cords are available and may be used if care is exercised in

their use.

C. If a long extension cord is used, (1) the marked electrical rating of the extension

cord should be at least as great as the electrical rating of the appliance, (2) if the

appliance is of the grounded type, the extension cord should be a grounding type

wire cord, and (3) the longer cord should be arranged so that it will not drape over the

counter top or table top where it can be pulled on by children or tripped over.

Introduction:

As the proud owner or the Gaggia

Espresso, you can now experience the

taste of a delicious cup of espresso or

cappuccino in the comfort of your own

home. Congratulations on making a

wise decision!

Espresso coffee, originally created in

Italy, is made by rapidly forcing water

that has been heated to the correct

brewing temperature, through a special

finely ground coffee. The heart of the

Espresso Gaggia is a precision

engineered pump. The pump and

water flow is easily controlled with just

a flick of the switch.

Making espresso or cappuccino is very

different from using a coventional

coffee maker. The Espresso Gaggia

operates with pressure and steam and

it is, therefore, important to read all the

instructions before using. Become

familiar with all parts of the machine

before operating the unit.

Important to know...

The taste of your coffee depends on

the characteristics of the beans from

which it is made, the type of bean,

where it was grown and processed.

The special flavor of a coffee bean is

determined by many factors, but its

taste and aroma are the result of the

roasting process. Most coffees

purchased from the supermarket are

roasted to a moderate degree.

Those beans are light in color and

have a dry, rather than an oily

surface. This is known as the

American roast (in USA).

The coffee beans that are roasted

for a longer period of time and at

higher temperatures will be much

darker in color. Darker beans will

produce a more flavorful cup of

coffee than the lightly-roasted

beans.

2. A variety of dark roasts is available

from which you can choose to brew

your espresso. Examples: Vienna

roast, French roast, Italian roast, etc.

Each of these roasts is a blend of

coffee beans that are roasted at a

specific temperature producing a

specific type of flavor.

There are decaffeinated beans that

have up to 98% of the caffeine

content removed.

The next time you purchase coffee

for your espresso maker, experiment

with one of the many kinds of coffee

being sold. You may just find that it

tastes better than the blend you

have been using.

3. A fine “espresso grind” for

pump-

driven machines must be used. Be

sure to ask for this when buying

coffee or when having beans ground.

Do not use a blade-type grinder

because it makes too much coffee

dust and produces an irregular grind.

4. The mark of real espresso is its dark

color, rich taste and the light

brown, natural froth called “crema” in

Italian.

5. Cappuccino is simply a combination

of espresso and hot, frothy milk.

Equal amounts of espresso, froth

and hot milk are recommended.

Cappuccino is usually topped with

cinnamon, nutmeg or chocolate

shavings.

6. Espresso Coffee should be served

immediately after it is made.

7. Espresso is

SeNed

in 2 to 2

l/2

oz.

demitasse cups. A 4 or 6 oz. cup or

glass is used for cappuccino.

8. Ideally, coffee beans should be

ground immediately before using.

Remember, it must be an “espresso

grind” for pump-driven machines.

9. It’s best to store ground coffee or

beans in an airtight container in the

freezer of your refrigerator. Ground

coffee readily picks up food flavors.

Preparation:

1. Remove the water reservoir cover (5)

and fill with cold water to the MAX

line indicated on reservoir (6). For

best taste, the use of bottled water is

recommended.

The water reservoir (6) can be

removed by sliding it forward and

then filling it.

IMPORTANT: When replacing

reservoir, be certain that suction

tube is inside the reservoir and not

kinked or blocked.

2. Insert plug (14) into a suitable wall

outlet (see point (1) under

“caution”).

3. Turn the power switch (1) to “I”. The

power-on indicator light (2) will light

up. Make certain that the hot water/

brew switch (3) is in the

“0”

position.

If you hear a noise it means the

pump is on, turn it off immediately

with the brew switch.

Priming the pump:

This procedu-

re prepares the pump and fills the

water boiler with fresh water. This

should be done whenever the

machine is switched on.

This machine features a self-priming

pump.

Place an empty cup on the drip-plate,

do not insert filter holder into brew head

and press hot water/coffee switch (3).

You will hear the sound of the

operating pump and after few seconds,

water will start to get out from the

brewing head.

Once cup is filled, set coffee switch (3)

onto pos.

“0”.

Espresso Gaggia in now ready to be

used.

Note: It may happen that the self-

priming feature of the pump does not

temporarily work due to an air lock. In

this case water does not get out from

brewing head, and the following

procedure should be followed:

a) Place a small frothing pitcher or mug

under the steam nozzle (8).

b) Turn the steam knob (7) on the side

counter-clockwise to open the

steam/hot water valve, and turn the

hot water/brew switch (3) to “I”. You

will hear the sound of the pump.

c) After a few seconds, a steady

stream of water will emerge from the

steam nozzle. Allow about one cup

of water to fill the pitcher. Shut the

steam/hot water valve and turn hot

water/brew switch to

“0”.

The Espresso Gaggia has been primed.

NOTE: The temperature ready-light

(3a) will automatically go on-and-off

as the machine’s boiler heats. When

the light goes on, the correct water

temperature for brewing (and

steaming) has been reached.

Wait at least 6 minutes for the machine

to reach its full operating temperature

(during this time, the indicator light will

go on and off frequently).

Another feature of the machine is the

“no-drip system”, eliminating most of

dripping from brewing head (that is

normal and due to the pump pressure in

the system).

The feature “no-drip system” causes a

light gurgle, for the return of hot water

into the tank. After coffee brewing,

however, a little dripping may occur due

to wet coffee grinds in the filter-holder.

Caution: Never operate pump

without water in machine as

damage to the pump may occur.

Damage of pump run without

water is not covered by warranty.

Making Espresso:

Follow the procedure described

under Preparation.

2. Allow about 6 minutes for the machine to

reach its proper operating temperature.

(Use this time to set table, ‘prepare

cups, coffee, milk, etc.).

3. Select the correct filter basket

(9a)

and insert it in the filter holder (9).

Use the small filter basket for 1 cup

and the large filter basket for 2 cups

of espresso. Then.insert the filter

holder (9) into the brew head

(11)

warm-up.

4. After the warm-up period, remove

the warm filter-holder (9) from the

brew-head (11) and fill with correctly

ground espresso coffee using the

measuring spoon provided Place

one level measure of coffee in

basket for each cup of espresso. Do

not overfill. Gently tamp down coffee

with the tamper (13) provided. Do

not compress too firmly.

5. Clean any excess coffee from the

rim of filter holder (9). Insert filter

holder into brew head (11) by

holding handle approximately 45

degrees to the left as you face

machine. When properly aligned,

move handle firmly to the right to

lock into position. The handle should

point to the front of the machine or

slightly to the right.

6. Place one or two espresso cups on

the drip plate (10) to line up with the

spouts of the filter holder. Depress hot

water/brew switch (3) to “I” position.

Espresso will start to flow into cups.

7. When cups are

3/4

full, release brew

switch to

“0”.

The more water. you

allow to flow, the weaker the coffee.

When properly made, the espresso

will have a light brown foam “crema”

floating on the top. If not, refer to

Troubleshooting Hints.

Remove

cups and serve.

8. To make more espresso, carefully

and slowly remove the filter holde;

by moving handle to the left. Use

care as hot water will be on top of

the coffee grinds in the holder. Some

water will continue to drip from brew

head as filter holder is removed.

That is normal and due to the pump

pressure in the system.

Knock out used coffee grinds from

filter basket and rinse. For more

espresso repeat steps 4 to 8 above.

“Perfect

crema”

device

A unique

disc fitted

L--l

into the

sr--

ftlterholder

will produce

coffee giving

the perfect

“Crema”

essential for the authentic espresso,

whatever type of grind you use.

Furthermore, you need only use the

two-

cup filter basket even when brewing for

one person (one level measure of coffee

only).

Preparing

cappuccino:

When preparing to make cappuccino,

have all of the ingredients at hand as

well as a frothing pitcher (or mug)

half-

filled with skimmed or low-fat milk and

cups that are larger (6 oz.) than those

used for espresso.

Frothing Milk:

Which kind of milk?

The less fat content in the milk the

denser the froth will be. Skimmed or

low-fat (2%) milk will provide a thick

foam. With regular milk the froth will

quickly collapse. The Turbo-Frother will

give you all the froth required but don’t

let milk come to a boil. Let frothed milk

stand for about 30 seconds before

spooning in onto the espresso.

It may require two or three tries to

“become an expert” but you will be

successful at frothing milk if you give it a

chance. Swivel the Turbo-Frother steam

nozzle slightly outward so that you can

get the frothing pitcher under the nozzle

without hitting the base of the machine.

1. Make espresso (in a large cups) as

described above.

2. Depress steam switch (4) to “I”.

3. After 10 to 15 seconds or, when

temperature ready-light (3a) goes

on, place the frothing pitcher

halffilled with low-fat milk under

Turbo Frother steam nozzle so that

tip is just under the surface of the

milk. See Fig. A.

4. Slowly turn steam valve knob (7)

counter clockwise to release steam.

IMPORTANT: The more you turn

the knob, the greater the steam

pressure for frothing.

5. Move pitcher in circular motion

keeping the tip of steam nozzle just

under surface of milk as it begins to

froth. Do not let milk come to a boil

since it will not froth.

6. When you have made enough froth,

turn steam knob clockwise to shut

off steam and remove pitcher. Put

steam switch (4) to

“0”

position.

7. Spoon the froth onto the espresso in

each cup and gently pour the hot milk

along the side of the cup. Top

each cup of cappuccino with a dash

of cinnamon, cocoa, nutmeg or

chocolate shavings. Serve.

8. NOTE: If you want to make more

espresso immediately after steaming

milk, the machine’s boiler must be

refilled with water and temperature

brought down to a brewing tempera-

ture. Otherwise, espresso may taste

“burned”. To do this: place an empty

cup on drip plate.

Do not insert filter holder. Turn hot

water/brew switch (3) to “I” letting

cup fill with water. Turn brew switch

“0”.

You many now proceed to make

more espresso.

AIR HOLE

FIG.

Making hot water:

Follow the procedure described

under preparation.

Turn the steam switch (4) to “I”.

Allow about 6 minutes for the

machine to reach its proper

operating temperature.

Place a pitcher under the steam

nozzle (8).

Turn the hot water/brew switch (3) to

“I” and slowly turn steam valve knob

(7) counter clockwise to release hot

water.

When you have made

th’e

desired

quantity of hot water, turn steam

knob clockwise and hot water/brew

switch to

“0”

to shut off hot water

and remove pitcher.

Put steam switch (4) to

“0”.

NOTE: If you want to make espresso

immediately after making hot water,

the temperature of the machine

boiler must be brought down to a

brewing temperature. Otherwise,

espresso may taste “burned”. To do

this: place an empty cup on drip

plate. Do not insert filter holder. Turn

hot water/brew switch (3) to

“I”

letting cup fill with water. Turn brew

switch

“0”.

You may now proceed to

make espresso.

Keeping it clean:

IMPORTANT: The steam nozzle

should be cleaned after each use in

order to avoid build up of milk

deposits that are very difficult to

clean. Cleaning is made easy as

can be seen in the Description of

Parts. The outer jacket of nozzle can

be removed by pulling downward.

The steam jet is cleaned by running

a shot of steam through it. A cleaning

needle has been supplied to clear

any obstruction. Outside of steam

pipe can be cleaned with a damp

cloth. Hole in steam nozzle must be

kept open. A needle may be used.

Clean filter holder and filter basket in

warm water after use.

Wipe body of machine with a damp

cloth asrequired.

Remove drip tray and plate (10,

10a)

and wash in warm soapy water. Use

sponge to clean out drip area.

Ground coffee will adhere to the seal

inside of the brew head (11). Keep it

clean.

The shower head (12) should be

unscrewed and cleaned periodically

depending on frequency of use.

After long periods of non-use, drain

stale water from machine by turning

hot water/brew switch to “I”. Howe-

ver, do this only after you have filled

reservoir with fresh water. Never

operate pump unless there

water

in reservoir (6).

NOTE: It is very normal for an

espresso machine to emit steam

and drip occasionally as the water

pressure changes during use. Be

certain to empty drip tray (1

Oa)

required.

Descaling:

In-hard water areas, minerals found in

the water will accumulate and affect

operation of the unit. Approximately

every four months (this can vary

depending on use and water

condition), clean the machine with

Gaggia descaler (in which case follow

the instructions on the packet).

Remove shower head (12) and clean.

Pour solution into reservoir and turn on

pump for 15 seconds. Allow solution to

flow through brew head and steam

nozzle for several seconds. Wait 20

minutes and repeat. Repeat process

until solution has been run through.

Rinse machine throughly by running

plain cold water through machine.

Replace shower head.

NOTE’: Product failure due to

scale accumulation is not

covered by warranty. No

other

servicing should be attempted by the

user. Use “Gaggia cleaner” for best results.

Trouble-shooting

hints:

Problem: Coffee does not flow

Check:

For water in reservoir

Filter basket clogged because

coffee is too fine or compressed

too firmly

Shower head requires cleaning

Problem: Coffee flows too quickly

Check:

Coffee is ground too coarsely

Coffee not pressed down with

tamper

Problem: Pump makes loud noise

Check:

No water in reservoir

Pump not primed

Coffee is ground too coarsely

Problem: Water leaking excessively

from filter holder

Check:

Filter holder not properly inserted

in brew head

Gasket in brew head dirty or worn

Coffee grinds not cleaned off the

rim of filter holder

Problem: Espresso has little crema froth

Check:

Coffee is ground too coarsely

Coffee is not pressed down with

tamper

Cl Coffee is too old or dried out

Problem: Espresso is too cold

Check:

Machine not warmed up (6 min.)

Coffee flows through too quickly-

coffee is ground too coarsely

Problem: Not enough milk froth

Check:

Use skimmed or low-fat milk

Steam nozzle and/or air intake

hole clogged

Milk is too hot

Gaggia CLASSIC COFFEE, Espresso User manual

Related papers

Other documents