SG Electronics SGCLK046 User manual

Brand: SG Electronics

Model: SGCLK046

Type: User manual

Digital Clock

User Manual

AN ISO 9001:2008 CERTIFIED COMPANY

E-mail: [email protected], Web: www.gblinst.com 1

DISCLAIMER

The information provided in this document is believed to be reliable. However, no responsibility is assumed

for any possible inaccuracies or omissions. S.G. Electronics reserves the right to make changes without

further notice to any product, herein to improve reliability, utility, or design. Specifications are subject to

change without notice.

Main Clock

GPS Clock 1

Clock 2

Clock 3

Clock 4

Specification

LED bar

4 * 2.3

4 Digit

Display Digit LED matrix LED matrix

Digit Size (in Inches) 6 * 4 8 * 4.5

4 Digit 4 Digit

Serial Features SGCLK044 SGCLK046 SGCLK048

Number of Alarms

Clock Size (L*H*D, in Inches)

Time Format 12 Hrs & 24 Hrs 12 Hrs. & 24 Hrs. 12 Hrs. & 24 Hrs.

Power Requirement 220V, 50Hz AC+10% 220V, 50Hz AC +10% 220V, 50Hz AC+10%

Suspension Method Mounting Hanging

Hanging

34.25*10.125*3

30.25*8.125*3

18.25*7.25*3

16 16 16

Digital Clock User Manual 2

1122

Hardware Design & Installation

10.

Calibration:

I) Through key panel

II) RS232 Interface With Computer

III) GPS Synchronization

In Build

In Build In Build In Build

In Build

Optional

Synchronization between clocks:

I) Through Wired Link (interface only)

II) Through Wireless link

Alarm Output

220 V AC 220 V AC 220 V AC

Height

7.25

Lenght

18.25

Width

SGCLK044

Height

8.125

Lenght

30.25

Width

SGCLK046

Height

10.125

Length

34.25

Width

SGCLK048

Mounting Process Antenna Setting

GPS Setting

3123

Hanging Method

Wire / Wireless Conection Process

Clock Key Calibration

Wire Connectivity

Master Clock Slave Clock

234

Master Clock Slave Clock Slave Clock Slave Clock Slave Clock

234

( )

GND

()

220V, 6A

AC, O/P

220V, 6A

AC, O/P

220V, 6A

AC, O/P

220V, 6A

AC, O/P

220V, 6A

AC, O/P

220V, 6A

AC, O/P

Cable Connectivity Details

SET

234

Solution Galore

S.G.Electronics

www.sgelectronics.co.in

DIGITAL CLOCK

MODEL: SGCLK04

Sl. No.:

( )

GND

()

220V, 6A

AC, O/P

Power Connection 220V, 50Hz, ±10%

Wire Connectivity

Computer Calibration

GPS Calibration

Master Clock

Wireless Connection

Master Clock

Wireless Connection

Slave Clock

234

Computer Clock

Slave Clock Slave Clock Slave Clock Slave Clock

234

( )

GND

()

220V, 6A

AC, O/P

Transmitted Data(TX)

Signal Ground(GND)

Receive Data(RX)

PIN SIGNAL

220V, 6A

AC, O/P

220V, 6A

AC, O/P

220V, 6A

AC, O/P

220V, 6A

AC, O/P

234

Master Clock Slave Clock Slave Clock Slave Clock Slave Clock

234

( )

GND

()

220V, 6A

AC, O/P

220V, 6A

AC, O/P

220V, 6A

AC, O/P

220V, 6A

AC, O/P

220V, 6A

AC, O/P

220V, 6A

AC, O/P

Main Clock

Clock 3

Clock 4

Digital Clock User Manual 3

GPS Calibration

MAINS 220VAC

234

( )

GND

()

220V, 6A

AC, O/P

Alarm Sound Output Connection (220 V Ac 6 Amp )

GPS

Clock 1

Clock 2

School Hospital

Firm / Industries Transport

Broadcast & Telecast Defense

Digital Clock User Manual 4

Click here to check

com port connectivity Click here to

Update Clock

Application

Alarm Duration

Click here to

set time format

Click here to

set 16 Alarm Click here to

set alarm duration

Select COM Port Update Clock Exit

Alarm 1 time: Alarm 9 time:

Alarm 2 time: Alarm10 time:

Alarm 3 time: Alarm 11 time:

Alarm 4 time: Alarm12 time:

Alarm 5 time: Alarm 13 time:

Alarm 6 time: Alarm 14 time:

Alarm 7 time:

Alarm 8 time:

Apply Reset All Exit

Alarm15 time:

Alarm 16 time:

Apply

Select Time Format

Configure Time Configure Time

Configure Alarm Configure Alarm

12-Hrs

Solution Galore

SG Electronics

The Industrial Automation Needs

SG Electronics

The Industrial Automation Needs

0 Sec

( in Seconds )

Clock Interface powered by SG Electronics Clock Interface powered by SG Electronics

13:30

GUI Application Calibration

Key Calibration

Step1: First Press SET Key and switch ON digital Clock with holding SET for

2 Second continuously.

Step2: After 2 second, Digital Clock Minute Panel will be Blinking for time

calibration.

Step3:First set minute, then Press SET Key for Hour calibration.

After that press SET key for time calibrate and save into digital clock with 00

second by default.

Time Format Setting :

Step1: First press SET Key and Switch ON Digital clock and holding the

SET key for 10 Second Continuously.

Step2: After 10 second Digital clock screen has show firstly 12HR / 24HR

With Blinking digit.

Step3:after that we choose 12hr & 24 hr time format by pressing Down and

UP keys.

Step4: After Choose time format Press SET key for setting time format save

into digital clock.

Step1: First switch ON digital clock properly, then press SET key.

Step2: After Press SET key , digital clock screen has show AL 1(Alarm1).

Step3:After 2 second alarm time calibration will be show with

blinking digit of minute.

Step4 : after that minute will be setting by pressing DOWN and UP key then,

press SET key for Hours setting.

After setting hours into digital clock press SET key for other 15 alarm time

Setting.

Step6: Rest all 15 Alarm setting follow through exact instruction of alarm1.

Step7: After 16 Alarm time setting ,Alarm on will be show, which is represents to

alarm duration setting that is minimum 0 second and maximum 59 second.

1. Alarm time is always in 24 hrs format and this clock initially on any

inbuilt alarm, for alarm it provides 220V AC 6 Amp output.

2. By default time of the clock is calibrated with format of 12 hrs

with no alarm set.

3.If we set alarm 00:00 then alarm does not work.

In duration of setting, if we no touch any key of digital clock for 5 Second,

digital clock auto go back to main time screen.

06:28 PM

Alarm Time Setting:

Time Calibration:

Apply

SG Electronics SGCLK046 User manual

Brand: SG Electronics

Model: SGCLK046

Type: User manual

Download PDF

report

SG Electronics SGCLK046 User manual

SG Electronics SGCLK046 User manual

Other documents