agape IRUB1112 Assembly Instructions

Brand: agape

Model: IRUB1112

Category: Sanitary ware

Type: Assembly Instructions

This manual is also suitable for

ERUB1115

agape IRUB1112 is a flexible hose with O-ring seal connectors that can be hand-tightened. It has a maximum torque of 3 Nm and should not be tightened with inappropriate tools or in inappropriate ways. The hose should not be set in the wall, and it should not be exposed to lateral stress or overtightened by any tool. It has a minimum bend radius of 25 mm for DN6, 30 mm for DN8, 35 mm for DN10, and 45 mm for DN13. Before bending the hose, consider a straight part of at least 1.5-2 times the external diameter.

agape IRUB1112 is a flexible hose with O-ring seal connectors that can be hand-tightened. It has a maximum torque of 3 Nm and should not be tightened with inappropriate tools or in inappropriate ways. The hose should not be set in the wall, and it should not be exposed to lateral stress or overtightened by any tool. It has a minimum bend radius of 25 mm for DN6, 30 mm for DN8, 35 mm for DN10, and 45 mm for DN13. Before bending the hose, consider a straight part of at least 1.5-2 times the external diameter.

ISTRUZIONI DI MONTAGGIO

ASSEMBLY INSTRUCTIONS

Rubinetti / Taps

1/2

RUBINETTI

FLESSIBILI

ISTRUZIONI DI MONTAGGIO

ASSEMBLY INSTRUCTIONS

Rubinetti /Taps- essibili/hose

COD.

16018 20160610/0 - SV

VERS. 2/2

Prima dell’installazione controllare la pre

-

sibili da ambo i lati.

Before installation, check presence and

integrity of the clamping of the side tu

bes.

Non serrare con utensili non

adatti o in punti non corretti.

Do not tighten by inappropriate

tools or in inappropriate ways.

Dopo il montaggio evitare sol

lecitazioni laterali anche mini

me, con qualsiasi utensile.

-

rante o astina).

Do not expose the hose to

lateral stress nor overtight by

any tool.

(Ex.: during the installation of

the faucet stud or the drain

pop-up lever).

Non incassare il condotto

nel muro.

Do not set the hose in the

wall.

torsione o in tensione.

Tighten the hose without

any twist or tension.

Il contatto prolungato con sostanze, pur

blandamente aggressive, può determina

re il danneggiamento della treccia ed il

Prolonged contact with any substance,

even scarcely aggressive, can cause

external braid damage and subsequent

Avvitare i raccordi con tenuta O.R.

a mano. Coppia massima di ser

raggio 3 Nm.

Hand-tighten O-ring seal connec

tors.

Max torque 3 Nm.

Avvitare i raccordi con tenuta a

guarnizione (dadi) a mano più

1/4 di giro con chiave appro

priata.

Hand-tighten connectors with

gasket seal (nuts) then apply

1/4 turn using an appropriate

wrench.

Rispettare il raggio minimo di cur

vatura.

Maintain minimum bend radius.

DN6 = 25 mm DN8 = 30 mm

DN10 = 35 mm DN13 = 45 mm

Prima dell’inizio della curvatura la

sciare un tratto rettilineo di almeno

1,5 - 2 volte il diametro esterno.

Before bending the hose please

consider a straight part of at least

1,5-2 times the external diameter.

Non collegare la messa a terra dell’impianto elettrico al

Chiudere l’impianto idraulico in caso di prolungata assen

nor to any other water piping.

Turn o the plumbing in case of long absence. Replace the

hose in case of leakage and anyway.

1

2

3

4

5

6

7

8

9

10

11

1
2

agape IRUB1112 Assembly Instructions

Brand: agape

Model: IRUB1112

Category: Sanitary ware

Type: Assembly Instructions

This manual is also suitable for

ERUB1115

agape IRUB1112 is a flexible hose with O-ring seal connectors that can be hand-tightened. It has a maximum torque of 3 Nm and should not be tightened with inappropriate tools or in inappropriate ways. The hose should not be set in the wall, and it should not be exposed to lateral stress or overtightened by any tool. It has a minimum bend radius of 25 mm for DN6, 30 mm for DN8, 35 mm for DN10, and 45 mm for DN13. Before bending the hose, consider a straight part of at least 1.5-2 times the external diameter.

in other languages

italiano: agape IRUB1112

Related papers

Other documents