PARTS
Read through all the instructions before beginning assembly. Unpack and identify all the parts.
Place them on a flat, non-abrasive surface. Assembly by six people is recommended.
A (6)
Leg Post
B (6)
Top Crossbar
2
C (4)
Decorative Panel
D (2)
Tabletop Crossbar
E (1)
F (6)
Canopy Short Bar
G (4)
Surpport Long Bar
Canopy Frame
H (2)
Surpport Short Bar
I (1)
J (1)
Tabletop
(with “J” label)
K (1)
Tabletop
(with “K” label)
Tabletop
(with “I” label)
L (1)
Tabletop
(with “L” label)
Special Warning
Assemble your gazebo on a soft, non-abrasive surface to avoid damage. The gazebo is heavy. Use care when handing.
Assembly by four adults is recommended. The gazebo is not intended to be a permanent structure. Take it down during
high winds or it may be damaged.
KEEP ALL FLAME AND HEAT SOURCES AWAY FROM CANOPY FABRIC
The canopy is made with flame-resistant fabric which meets CPAI-84 specifications. It is not fireproof. The canopy fabric
will burn if left in continuous contact with flame source. The application of any foreign substance to the canopy fabric
may render the flame-resistant properties ineffective.
Caution:
This gazebo is made for explicit purpose of providing limited outdoor sun shade and is not to be used as a toy, shelter
or tent. This gazebo is not intended for inclement weather in any form including, but not limited to: rain, hail, sleet, snow
and/or wind. Do not locate structure near any open flame. Do not use structure as a support. Do not shake, lean or climb
on structure. Children under age of 10, near the structure, should be supervised by a competent adult at all times.
ACCESSORIES
Oa (16 + 1 spare)
M6 x 15L Bolt
Ob (48 + 3 spares)
M6 x 20L Bolt
Oc (6 + 1 spare)
M6 x 25L Bolt
Oj (2)
Open Hex Wrench
Ok (2)
Allen Wrench
Oi (1)
Hook
Od (12 + 1 spare)
M6 x 30L Bolt
Ol (1)
Touch up Paint
Oe (84 + 3 spares)
Metal Washer
Of (18 + 1 spare)
Nut
Og (6)
Bracket
Oh (12)
Lawn Stake
Om (1)
Assembly
Instructions Sheet
3
M (1)
Canopy Fabric
N (6)
Net
ASSEMBLY INSTRUCTIONS
4
Fig. 3
B
Ob
Ob
Oe
B
Og Oe
Attach a decorative panel (C) to two leg
posts (A). Insert two hooks of decorative
panel (C) into two holes of two leg posts (A).
See Fig. 1. Then insert the pins through the
decorative panel (C) and into the leg post (A)
for each hole. See Fig. 2. Repeat procedure for
the remaining decorative pannels (C) and leg
posts (A).
Attach a top crossbar (B) to the assembled
frame (A&C). Line up all holes and for each
hole insert an M6 x 20L bolt (Ob) through a metal
washer (Oe), top crossbar (B) and secure into
leg posts (A). Don’t tighten completely. Repeat
procedure for the other side and the remaining
top crossbars (B). Attach a bracket (Og) to a
leg post (A). Line up all holes and for each hole
insert an M6 x 20L bolt (Ob) through a metal
washer (Oe) and secure into the post (A). Don’t
tighten completely. Repeat procedure for the
remaining leg posts (A). See Fig. 3. Tighten all
bolts.
1
2
A
A
C
CA
A
C
Fig. 1
Fig. 2
A
C
5
Fig. 4
Fig. 5
Fig. 6
Fig. 7
F
E
M
F
Od
Oe Oe
Of
E
E
F
D
D
a
O
C
DD
Oa
Oa
Attach a tabletop crossbar (D) to the assembled
frame (A&C) Line up all holes, for each hole
insert an M6 x 15L bolt (Oa) through the bracket
of tabletop crossbar (D) and secure into the leg
post (A) or the decorative pannel (C). Don’t
tighten completely. Repeat procedure for the
remaining tabletop crossbars (D). See Fig. 4.
and Fig. 5. Tighten all bolts. NOTE: The holes
of tabletop crossbars (D) facing inside (For
attaching to tabletops).
Attach the canopy short bars (F) to the canopy
frame (E). For each hole, insert an M6 x 30L
bolt (Od) through a metal washer (Oe), canopy
frame (E), short bar (F), another metal washer (Oe)
and secure with a nut (Of). Tighten all bolts and
nuts. Repeat procedure for the remaining five
short bars (F). See Fig. 6.
Place the canopy fabric (M) to the assembled
canopy frame (E&F). Insert each top short bars of
canopy frame (E) into each top pockets of the canopy
fabric (M). Pull down the canopy fabric and spread to
the location. See Fig. 7.
3
4
5
A
C
Fig. 8
Fig. 9
Fig. 11
6
Oe
Od
Of
Oe
Og
K
J
IL
G
Ob
Oe
Oe
Oc
I
Fig. 12
Ob
Oe
J
Fig. 14
Oe
Of
I
J
Oc
Oe
H
Fig. 13
Ob
Oe
Of
Oe
I
J
CH
Oa
Fig. 10
Oa G
C
Place the completed canopy onto the top of
assembled leg posts. Line up the holes, for each
hole insert an M6 x 30L bolt (Od) through a metal
washer (Oe), a short bar (F), a bracket (Og), another
metal washer (Oe) and secure with a nut (Of). Don’t
tighten completely. Repeat procedure for the
remaining five short bars (F). Tighten all bolts and
nuts. See Fig. 8. Pull down the edges of the canopy
fabric and insert each tip of the canopy short bar (F)
into the pocket of the canopy fabric.
: Attach the tabletop (I) to the tabletop crossbar (D).
Line up the hole, insert an M6 x 20L bolt (Ob) through
a metal washer (Oe), the tabletop (I) and secure into
the tabletop crossbar (D) for each hole. See Fig. 9.
Don’t tighten completely. Attach the support long bar (G)
to the decorative panel (C), insert an M6 x 15L bolt (Oa)
through the support long bar (G) and secure into the
decorative panel (C). See Fig. 10. Don’t tighten
completely. Attach the support long bar (G) to the
tabletop (I), insert an M6 x 25L bolt (Oc) through a
metal washer (Oe), the support long bar (G) and
secure into the tabletop (I). See Fig. 11. Don’t
tighten completely.
: Attach the tabletop (J) to the tabletop
crossbar (D). See Fig. 12. Attach the tabletop (J)
to the tabletop (I). Line up the hole, insert an
M6 x 20L bolt (Ob) through a metal washer (Oe),
the tabletop (J), the tabletop (I), another metal
washer (Oe) and secure with a nut (Of). Attach
the support short bar (H) to the decorative
panel (C), insert an M6 x 15L bolt (Oa) through
the support short bar (H) and secure into the
decorative panel (C). See Fig. 13. Don’t tighten
completely. Attach the support short bar (H) to
the tabletop (J&I), insert an M6 x 25L bolt (Oc)
through a metal washer (Oe), the tabletop (J&I),
the support short bar (H), another metal washer (Oe)
and secure with a nut (Of). See Fig. 14. Don’t tighten
completely.
6
7
F
Fig. 15
Fig. 16
Fig. 17
Fig. 18
Fig. 19
7
G
Oe
Oe
J
K
Ob
Of
K
J
I
L
Oa
Oe
G
J
K
Of Oe Oe
Ob
Oc
G
Oi
A
Oh
Secure the gazebo to the ground by inserting
the lawn stakes (Oh) through the holes at the
bottom of the leg post into the ground. See
Fig. 18. Attach the S shaped hook (Oi) to the
ring of the canopy. The S shaped hook is used
for hanging decoration items if necessary. See
Fig. 19.
8
: Repeat step for remaining tabletop (K&L).
: Attach the tabletop (J&I) to the tabletop (K&L).
Line up the hole, insert an M6 x 15L bolt (Oa)
through the support long bar (G) and secure into the
decorative panel (C) for total of 2 holes. See Fig. 15.
Don’t tighten completely. Attach the support long
bar (G) to the tabletop (J&K), insert an M6 x 25L
bolt (Oc) through a metal washer (Oe), the support
bar (G) and secure into the tabletop (J&K). Don’t
tighten completely. Then insert an M6 x 20L bolt (Ob)
through a metal washer (Oe), the tabletop (K&J),
another metal washer (Oe) and secure with a
nut (Of) for total of 2 holes. See Fig.16 and Fig. 17.
Don’t tighten completely.
: Tighten all bolts and nuts.
C
8
Made in / Hecho en CHINA for Kmart Corporation, Hoffman Estates, IL 60179
SHOP kmart.com
See our extensive assortment of outdoor living products
on-line at www.sears.com and www.kmart.com
For questions or comments about product:
Call toll-free: 800-457-4652
Please refer to part numbers when reordering
CARE INSTRUCTIONS
Wash with a mild solution of soap and water; rinse thoroughly. Dry completely. Do not use bleach or solvents.
Cover furniture with outdoor furniture covers when not in use.
Fig. 20
M
N
N
B
F
Locate the nets (N) to the net bars of top
crossbars (B) with Velcro tabs. See Fig. 20.
Make sure the top crossbar is between two
edges of the canopy fabric (M). Affix inner
edges with Velcro tabs. See Fig. 21.
9
Your gazebo is now ready for use. Enjoy!
/
